Teat morphology across five buffalo breeds: a multi-country collaborative study.

The buffalo (Bubalus bubalis) is a species of worldwide importance, raised to produce milk, meat, and hides, and often used as a working animal in rural contexts with low access to hi-tech solutions. In the present study, 100 lactating buffaloes (50 primiparous and 50 pluriparous) of five popular breeds were recruited to characterize and compare teat morphology. In particular, the focus was put on the Nili Ravi, Mediterranean, Egyptian, Bulgarian Murrah, and Azeri buffaloes raised in Pakistan, Italy, Egypt, Bulgaria, and Iran, respectively. In all countries, a longitudinal cross-section ultrasound was obtained before the milking to measure teat parameters at individual level: overall, teat canal length (TCL) averaged 24.13 mm, teat diameter (TD) 30.46 mm, cisternal diameter (CD) 17.80 mm, and teat wall (TW) 7.12 mm. The most variable trait across breeds was TCL which was positively correlated with CD and TD and negatively with TW, regardless of the teat position (front/rear or left/right). A strong negative correlation was found between TW and CD (- 0.43). The analysis of variance revealed that the fixed effect of breed significantly affected all the traits except TD. In fact, Bulgarian Murrah, Azeri, and Egyptian buffaloes presented the greatest estimate of TCL, whereas NR the smallest (14.70 mm). The TW was maximum in Nili Ravi, Egyptian, and Mediterranean buffaloes, with estimates equal to 8.19, 7.59, and 8.74 mm, respectively. Nili Ravi also showed the greatest TL (82.39 mm). In terms of CD, the lowest least square mean was that of Mediterranean buffaloes (12.14 mm). Primiparous and pluriparous buffaloes differed in terms of TD, TW, and TL, with older animals presenting the highest least square mean. In terms of position, instead, significant differences were observed for TD, CD, and TL when comparing front and rear teats, as left and right teats did not differ. Teat anatomy includes a set of heritable morphological features and is therefore breed-dependent. Differences presented in this study could be attributed to the divergent breeding objective and selective pressure across the five breeds; e.g., in some cases such as Mediterranean buffalo, selection for decades was oriented to improve milk production and milkability and achieve optimal conformation for mechanical milking. A better understanding of the mammary gland anatomical descriptors can be informative of the history of a breed and could provide useful insights to guide possible selection.

Study of the Milkability of the Mediterranean Italian Buffalo and the Tunisian Maghrebi Camel According to Parity and Lactation Stage.

While considered as hard milkers, both buffaloes and camels are milked with equipment destined for dairy cows based on external morphological similarities with this species. This work aimed to study similarities and differences in milkability traits between Mediterranean buffaloes and Maghrebi she-camels and to evaluate the effect of parity and lactation stage. A total of 422 milk flow curves recorded with an electronic milkmeter (Lactocorder®) for both species were accessed. Milking characteristics including milk yield per milking, peak milk flow, average milk flow, duration of the main milking phase, duration of total milking, duration of various phases of milk flow, lag time and time to milk ejection, stripping yield, overmilking time and incidence of bimodal milk flow curves were evaluated for both species. Results showed that the values of milk yield per milking, duration of the main milking phase and duration of total milking were higher in buffaloes (3.98 ± 0.10 kg; 4.07 ± 0.11 min; 9.89 ± 0.21 min, respectively) compared to camels (3.51 ± 0.08 kg; 3.05 ± 0.09 min; 3.76 ± 0.09 min, respectively). However, camels had significantly higher peak and average milk flow (2.45 ± 0.07 kg/min and 1.16 ± 0.03 kg/min, respectively). Camels took significantly less time for milk ejection to occur. Only 15.49% of recorded curves were bimodal in buffaloes while 34.93% of bimodal curves were recorded for camels. Overmilking was significantly higher in buffaloes (3.64 ± 0.21 min vs. 0.29 ± 0.02 min). Parity and lactation stage had a significant effect on most studied milking traits suggesting the need for some particular practices with primiparous animals and animals at different levels of lactation for both species.

The Effect of Pre-milking Stimulation on Teat Morphological Parameters and Milk Traits in the Italian Water Buffalo.

Water buffaloes (Bubalus bubalis) are very sensitive to environmental stimulus before and during milking, and this explains why disrupted milk ejections due to blood oxytocin level instability are frequent in this species. According to the literature, the manual stimulation (MS) of teats before milking promotes oxytocin release and allows milk ejection to start within 2-3 min. However, the pre-milking stimulation of teats is not always part of the milking routine in Italian buffalo farms; moreover, buffaloes with unstable milk let-down are sometimes treated with exogenous oxytocin (OX). Different types of pre-milking stimulation can impact differently on the mammary gland epithelium and structures and, therefore, on milk yield. In this study, we observed the changes in teat morphological traits before and after the application of three types of stimuli, i.e., no manual stimulation (NS), MS, and OX, in buffaloes reared in an Italian dairy farm. In particular, measurements were available for 23 and 21 buffaloes for front and rear teats, respectively. Subsequently, the effect of the pre-milking stimulation type was estimated on teat morphological characteristics and on milk traits recorded after the application of stimuli. The results showed that the teat canal length was shorter (P < 0.05) after stimulation in the case of MS and OX compared to NS. Cistern diameter was overall greater for MS and lower for OX. On the contrary, teat wall thickness was greater and lower for OX and MS, respectively. Milk yield and quality (fat, protein, and somatic cell score) were similar across the three types of pre-milking stimulation. In perspective, the impact of these types of pre-milking stimulation should be evaluated on a large scale, and the focus might be put on mammary gland epithelium integrity, mastitis incidence, and other udder health indicators in milk, e.g., electrical conductivity, differential somatic cell count, lactose content, and sodium and chloride concentration.

Biochemical and nutritional characteristics of buffalo meat and potential implications on human health for a personalized nutrition.

The human consumption of food animal products is the main topic of an important debate among professionals in this sector: dietologists, dietitians and nutritional biologists. The red meat provides all the essential amino acids, bioavailable iron, zinc, calcium, lipids and B-group vitamins. A valid alternative to beef could be the buffalo meat. Italy is the largest European producer of buffalo meat and derivatives. The high nutritional characteristics of buffalo meat make it suitable to be included in the Mediterranean diet to customize it in relation to the needs and conditions of the population. Polyunsaturated/saturated fatty acids ratio can be influenced by diet, breed and type of breeding, but muscle tissue fat percentage is the main factor in determining a favorable fatty acid composition. This review focuses on the biochemical and nutritional characteristics of the buffalo meat (content of fats, cholesterol, amino acids, vitamins and minerals), explaining their variability depending on the different breeds, and the favorable implications on the human health. These results suggest that buffalo meat can be a healthier alternative to beef, not only for healthy people in particular physiological conditions (i.e. pregnancy), but also for persons at risk for cardiovascular and cerebrovascular diseases, thus achieving the goal of a personalized nutrition.

Application of Microbiological Method Direct Epifluorescence Filter Techique/Aerobic Plate Count Agar in the Identification of Irradiated Herbs and Spices.

Irradiation is a preservation technology used to improve the safety and hygienic quality of food. Aim of this study was to assess the applicability and validity of the microbiological screening method direct epifluorescence filter technique (DEFT)/aerobic plate count (APC) (EN 13783:2001) for the identification of irradiated herbs and spices. Tests on non-irradiated and irradiated samples of dried herbs and spices were performed. The method was based on the comparison of APC and count obtained using DEFT. In accordance with the standard reference, this method is not applicable to samples with APC<103 colony forming units (CFU)/g and this is its main limit. The results obtained in our laboratories showed that in 50% of cases of non-irradiated samples and in 96% of the samples treated with ionising radiation, the method was not applicable due to a value of CFU/g <103.