Genome-based taxonomic identification and safety assessment of an Enterococcus strain isolated from a homemade dairy product.

The aim of this study was to explore the taxonomic identification and evaluate the safety of a bacterium, Enterococcus lactis IDCC 2105, isolated from homemade cheese in Korea, using whole genome sequence (WGS) analysis. It sought to identify the species level of this Enterococcus spp., assess its antibiotic resistance, and evaluate its virulence potential. WGS analysis confirmed the bacterial strain IDCC 2105 as E. lactis and identified genes responsible for resistance to erythromycin and clindamycin, specifically msrC, and eatAv, which are chromosomally located, indicating a minimal risk for horizontal gene transfer. The absence of plasmids in E. lactis IDCC 2105 further diminishes the likelihood of resistance gene dissemination. Additionally, our investigation into seven virulence factors, including hemolysis, platelet aggregation, biofilm formation, hyaluronidase, gelatinase, ammonia production, and ß-glucuronidase activity, revealed no detectable virulence traits. Although bioinformatic analysis suggested the presence of collagen adhesion genes acm and scm, these were not corroborated by phenotypic virulence assays. Based on these findings, E. lactis IDCC 2105 presents as a safe strain for potential applications, contributing valuable information on its taxonomy, antibiotic resistance profile, and lack of virulence factors, supporting its use in food products.

Key factors for the survival of Lactiplantibacillus plantarum IDCC 3501 in manufacturing and storage.

Functional microbiome development has steadily increased; with this, the viability of microbial strains must be maintained not only after the manufacturing process but also at the time of consumption. Survival is threatened by various unavoidable factors during freeze-drying and shelf storage. Here, the aim was to optimize the manufacturing process of the functional strain Lactiplantibacillus plantarum IDCC 3501 after freeze-drying and storage. Explosive growth was achieved using a medium composition with two nitrogen sources and a mineral, and growth was drastically improved by neutralizing the medium pH during the culture of L. plantarum IDCC 3501. Culture optimization involved a smaller cell size, leading to less intracellular free water. Moreover, when maltodextrin (MD) powder was directly added to the harvested cells, some intracellular free water was extracted from the bacterial cells, resulting in a dramatic increase in the viability of L. plantarum IDCC 3501 after freeze-drying and subsequent storage. Furthermore, MD enhanced survival in a dose-dependent manner. Bacterial survival was correlated with lysozyme tolerance; therefore, the positive result might have been caused by the osmotic dehydration of intracellular free water, which would potentially damage the bacterial cells via ice crystallization and/or a phase transition during freeze-drying. These critical factors of L. plantarum IDCC 3501 processing provide perspectives on survival issues for manufacturing microbiome strains. KEY POINTS: • Culture conditions for probiotic bacteria were optimized for high growth yield. • Osmotic dehydration improved bacterial survival after manufacturing and shelf storage. • Reduction in intracellular free water content is crucial for intact survival.

Pyrophosphate-Enhanced Oxidase Activity of Cerium Oxide Nanoparticles for Colorimetric Detection of Nucleic Acids.

In recent years, cerium oxide (CeO2) nanoparticles (NPs) have drawn significant attention owing to their intrinsic enzyme mimetic properties, which make them powerful tools for biomolecular detection. In this work, we evaluated the effect of pyrophosphate (PPi) on the oxidase activity of CeO2 NPs. The presence of PPi was found to enhance the oxidase activity of CeO2 NPs, with enhanced colorimetric signals. This particular effect was then used for the colorimetric detection of target nucleic acids. Overall, the PPi-enhanced colorimetric signals of CeO2 NPs oxidase activity were suppressed by the presence of the target nucleic acids. Compared with previous studies using CeO2 NPs only, our proposed system significantly improved the signal change (ca. 200%), leading to more sensitive and reproducible colorimetric analysis of target nucleic acids. As a proof-of-concept study, the proposed system was successfully applied to the highly selective and sensitive detection of polymerase chain reaction products derived from Klebsiella pneumoniae. Our findings will benefit the rapid detection of nucleic acid biomarkers (e.g., pathogenic bacterial DNA or RNA) in point-of-care settings.

Simultaneous monitoring of the bioconversion from lysine to glutaric acid by ethyl chloroformate derivatization and gas chromatography-mass spectrometry.

Glutaric acid is a precursor of a plasticizer that can be used for the production of polyester amides, ester plasticizer, corrosion inhibitor, and others. Glutaric acid can be produced either via bioconversion or chemical synthesis, and some metabolites and intermediates are produced during the reaction. To ensure reaction efficiency, the substrates, intermediates, and products, especially in the bioconversion system, should be closely monitored. Until now, high performance liquid chromatography (HPLC) has generally been used to analyze the glutaric acid-related metabolites, although it demands separate time-consuming derivatization and non-derivatization analyses. To substitute for this unreasonable analytical method, we applied herein a gas chromatography - mass spectrometry (GC-MS) method with ethyl chloroformate (ECF) derivatization to simultaneously monitor the major metabolites. We determined the suitability of GC-MS analysis using defined concentrations of six metabolites (l-lysine, cadaverine, 5-aminovaleric acid, 2-oxoglutaric acid, glutamate, and glutaric acid) and their mass chromatograms, regression equations, regression coefficient values (R2), dynamic ranges (mM), and retention times (RT). This method successfully monitored the production process in complex fermentation broth.

Removal of Fluoride from Water Using a Calcium-Modified Dairy Manure-Derived Biochar.

This study investigated the removal of fluoride from water using a calcium-modified dairy manure-derived biochar (Ca-DM500). The Ca-DM500 showed a 3.82 - 8.86 times higher removal of fluoride from water than the original (uncoated) manure-derived biochar (DM500). This is primarily attributed to strong precipitation/complexation between fluoride and calcium. The Freundlich and Redlich-Peterson sorption isotherm models better described the experimental data than the Langmuir model. Additionally, the removal kinetics were well described by the intraparticle diffusion model. The Ca-DM500 showed high reactivity per unit surface area [0.0001, 0.03, 0.16 mg F per m2 for Douglas fir-derived biochar (DF-BC), DM500. and Ca-DM500, respectively] for retention of fluoride reflecting the importance of surface complexation. The copresence of anions reduced removal by Ca-DM500 in the order SO 4 2 - ≈ PO 4 3 - > NO 3 - . The sorption behavior of fluoride in a continuous fixed-bed column was consistent with the Thomas model. Column studies demonstrated that the Ca-DM500 shows a strong affinity for fluoride, a low release potential, and a stable (unreduced) removal capacity through regeneration and reuse cycles.

Polyhydroxybutyrate production in halophilic marine bacteria Vibrio proteolyticus isolated from the Korean peninsula.

Polyhydroxybutyrates (PHB) are biodegradable polymers that are produced by various microbes, including Ralstonia, Pseudomonas, and Bacillus species. In this study, a Vibrio proteolyticus strain, which produces a high level of polyhydroxyalkanoate (PHA), was isolated from the Korean marine environment. To determine optimal growth and production conditions, environments with different salinity, carbon sources, and nitrogen sources were evaluated. We found that the use of a medium containing 2% (w/v) fructose, 0.3% (w/v) yeast extract, and 5% (w/v) sodium chloride (NaCl) in M9 minimal medium resulted in high PHA content (54.7%) and biomass (4.94 g/L) over 48 h. Addition of propionate resulted in the production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (P(HB-co-HV)) copolymer as propionate acts as a precursor for the HV unit. In these conditions, the bacteria produced poly(3-hydroxybutyrate-co-3-hydroxyvalerate) containing a 15.8% 3HV fraction with 0.3% propionate added as the substrate. To examine the possibility of using unsterilized media with high NaCl content for PHB production, V. proteolyticus was cultured in sterilized and unsterilized conditions. Our results indicated a higher growth, leading to a dominant population in unsterilized conditions and higher PHB production. This study showed the conditions for halophilic PHA producers to be later implemented at a larger scale.

Biotechnological potential of microbial consortia and future perspectives.

Design of a microbial consortium is a newly emerging field that enables researchers to extend the frontiers of biotechnology from a pure culture to mixed cultures. A microbial consortium enables microbes to use a broad range of carbon sources. It provides microbes with robustness in response to environmental stress factors. Microbes in a consortium can perform complex functions that are impossible for a single organism. With advancement of technology, it is now possible to understand microbial interaction mechanism and construct consortia. Microbial consortia can be classified in terms of their construction, modes of interaction, and functions. Here we discuss different trends in the study of microbial functions and interactions, including single-cell genomics (SCG), microfluidics, fluorescent imaging, and membrane separation. Community profile studies using polymerase chain-reaction denaturing gradient gel electrophoresis (PCR-DGGE), amplified ribosomal DNA restriction analysis (ARDRA), and terminal restriction fragment-length polymorphism (T-RFLP) are also reviewed. We also provide a few examples of their possible applications in areas of biopolymers, bioenergy, biochemicals, and bioremediation.

Cytotoxic Effects of ZnO Nanoparticles on the Expression of ROS-Responsive Genes in the Human Cell Lines.

In the present investigation, engineered ZnO nanoparticles were tested for their induced oxidative stress in T47D tumor cell lines. The expressions of reactive oxygen species (ROS) related genes, glutathione S-transferase (GST) and catalase were quantified by real time-polymerase chain reaction (RT-PCR). In addition, qualitative analysis of GST was also performed at the cell level using molecular beacon (MB) technology. The tested nanoparticles were 20 nm in size, water-dispersible and treated on human breast tumor epithelial cell lines at 20, 40, 80 µg/ml concentration with 14, 28, 48 h incubation times. Nanoparticles induced expressions of ROS responsive genes at molecular and cellular level, produces consistent results with respect to different dosage and incubation time. The experiment showed that the expression of both GST and catalase genes were maximized at 28 h with 80 µg/ml concentration. However, the toxic effect of the monodisperse ZnO nanoparticles was not significant compared with control experiments, demonstrating its high potential in the applications of nanomedicines for a diagnostic and therapeutic tool.

In vitro cytotoxic evaluation of MgO nanoparticles and their effect on the expression of ROS genes.

Water-dispersible MgO nanoparticles were tested to investigate their cytotoxic effects on oxidative stress gene expression. In this in vitro study, genes related to reactive oxygen species (ROS), glutathione S-transferase (GST) and catalase, were quantified using real-time polymerase chain reactions (molecular level) and molecular beacon technologies (cellular level). The monodispersed MgO nanoparticles, 20 nm in size, were used to treat human cancer cell lines (liver cancer epithelial cells) at different concentrations (25, 75 and 150 µg/mL) and incubation times (24, 48 and 72 h). Both the genetic and cellular cytotoxic screening methods produced consistent results, showing that GST and catalase ROS gene expression was maximized at 150 µg/mL nanoparticle treatment with 48 h incubation. However, the genotoxic effect of MgO nanoparticles was not significant compared with control experiments, which indicates its significant potential applications in nanomedicine as a diagnostic and therapeutic tool.

Development of Blended Biopolymer-Based Photocatalytic Hydrogel Beads for Adsorption and Photodegradation of Dyes.

Blended biopolymer-based photocatalytic hydrogel beads were synthesized by dissolving the biopolymers in 1-ethyl-3-methylimidazolium acetate ([Emim][Ac]), adding TiO2, and reconstituting the beads with ethanol. The incorporation of modifying biopolymer significantly enhanced the adsorption capacity of the cellulose/TiO2 beads. Cellulose/carrageenan/TiO2 beads exhibited a 7.0-fold increase in adsorption capacity for methylene blue (MB). In contrast, cellulose/chitosan/TiO2 beads showed a 4.8-fold increase in adsorption capacity for methyl orange (MO) compared with cellulose/TiO2 beads. In addition, cellulose/TiO2 microbeads were prepared through the sol-gel transition of the [Emim][Ac]-in-oil emulsion to enhance photodegradation activity. These microbeads displayed a 4.6-fold higher adsorption capacity and 2.8-fold higher photodegradation activity for MB than the millimeter-sized beads. Furthermore, they exhibited superior dye removal efficiencies for various dyes such as Congo red, MO, MB, crystal violet, and rhodamine B, surpassing the performance of larger beads. To expand the industrial applicability of the microbeads, biopolymer/TiO2 magnetic microbeads were developed by incorporating Fe2O3. These magnetic microbeads outperformed millimeter-sized beads regarding the efficiency and time required for MB removal from aqueous solutions. Furthermore, the physicochemical properties of magnetic microbeads can be easily controlled by adjusting the type of biopolymer modifier, the TiO2 and magnetic particle content, and the ratio of each component based on the target molecule. Therefore, biopolymer-based photocatalytic magnetic microbeads have great potential not only in environmental fields but also in biomedical fields.

Reswellable alginate/activated carbon/carboxymethyl cellulose hydrogel beads for ibuprofen adsorption from aqueous solutions.

In this study, alginate (Alg) composite beads were prepared by blending with activated carbon (AC) to enhance adsorption capacity for ibuprofen and carboxymethyl cellulose (CMC) to create a reswellable hydrogel. The dried Alg/AC/CMC composite beads could be recovered to sizes and morphologies similar to the initial hydrogel states via a simple reswelling process; however, the dried Alg/AC composite beads without CMC could not be recovered to the initial hydrogel state. Following the reswelling process, the dried Alg/AC/CMC beads demonstrated an 86 % recovery (qe = 34.0 mg/g) in the adsorption capacity for ibuprofen compared to the initial hydrogel beads (qe = 39.6). In contrast, the reswelled Alg/AC beads exhibited only 18 % (qe = 8.6) of the initial adsorption capacity (qe = 48.1). We elucidated the effects of the substitution degree of CMC, AC content, and solution pH on the reswelling property and ibuprofen adsorption capacity of the Alg/AC/CMC composite beads. The adsorption kinetics and isotherms of the prepared composite beads in the hydrogel and reswelled states fit the pseudo-second-order and Langmuir models, respectively. Furthermore, the reswelled Alg composite beads exhibited high adsorption capacity (>93 %) after 10 cycles. Taken together, our findings indicate that the Alg/AC/CMC composite beads can be used as adsorbents without a considerable decrease in adsorption performance by reswelling the beads with distilled water after long-term storage in a dry state.

Submerged leaves of live indoor foliage plants adsorb H1N1 influenza virus from suspension.

Control of hazardous indoor particles using plants has attracted interest due to the increasing worldwide air pollution and spread of pandemic-causing viruses. However, the interaction between human pathogenic viruses (HPVs) and live plants has not been examined largely due to issues in detecting tiny amounts of infectious viruses in a carrier (such as an aerosol) and the lack of suitable examination methods. In this study, as a novel evaluation method, the effect of submerged leaves of live plants on HPVs in water was examined, using the H1N1 influenza virus as a model. Selected plant foliage of a live plant was immersed in a small bag containing HPV water suspension. In an initial screening test, the activities of 20 different plant species on the virus suspension were evaluated using a rapid virus detection kit. Ten plant species had the capability to decrease virus concentrations in the water suspension within 72 h. Among the experimental plant species, Epipremnum aureum showed the highest virus decreasing characteristics when examined using both the kit and quantitative real time polymerase chain reaction. The capacity of immersed leaf of live E. aureum to decrease viral content was enhanced when the plant-containing pot was electrically grounded to the earth (approximately 70% decrease in virus concentration). The foliage sample analysis showed that virus adsorption to the plant foliage surface could be the major reason for the decrease in the suspension. These results suggest that the proposed method can be applied to select plants to further investigate plant-HPV interactions.

Adsorptive Behavior of Cu2+ and Benzene in Single and Binary Solutions onto Alginate Composite Hydrogel Beads Containing Pitch Pine-Based Biochar.

In this study, we prepared alginate composite hydrogel beads containing various compositions of biochar produced from pitch pine (Pinus rigida) for the removal of Cu2+ and benzene from model pollutant solutions. The properties of the alginate/biochar hydrogel beads were evaluated using scanning electron microscopy, Fourier transform infrared spectroscopy, and Brunauer−Emmet−Teller analyses. Adsorption behavior of alginate/biochar hydrogel beads indicated that the adsorption capacities for Cu2+ (28.6−72.7 mg/g) were enhanced with increasing alginate content, whereas the adsorption capacities for benzene (20.0−52.8 mg/g) were improved with increasing biochar content. The alginate/biochar hydrogel beads exhibited similar adsorption capacities for Cu2+ and benzene in the concurrent system with Cu2+ and benzene compared to those in a single pollutant system. Adsorption kinetics and isotherm studies of the alginate/biochar hydrogel beads followed the pseudo-second-order model (r2 = 0.999 for Cu2+, and r2 = 0.999 for benzene), and Langmuir model (r2 = 0.999 for Cu2+, and r2 = 0.995 for benzene). In addition, alginate/biochar hydrogel beads (containing 1 and 4% biochar) exhibited high reusability (>80%). Therefore, alginate/biochar hydrogel beads can be applied as adsorbents for the removal of multiple pollutants with different properties from wastewater.

Adsorptive removal of synthetic plastic components bisphenol-A and solvent black-3 dye from single and binary solutions using pristine pinecone biochar.

The existing study deals with adsorptive removal of the endocrine-disrupting chemical bisphenol-A and toxic azo dye solvent black-3 from single and binary solutions. These two chemicals are commonly used as an additive in the synthetic plastic industries. Among the tested twenty pristine and modified biochars, the pristine pinecone biochar produced at 750 °C revealed greater bisphenol-A removal. Simulation of the experimental data obtained for bisphenol-A and dye removal from the single-component solution offered a best-fit to Elovich (R2 > 0.98) and pseudo-second-order (R2 > 0.99) kinetic models, respectively. Whereas for the bisphenol-A + dye removal from binary solution, the values for bisphenol-A adsorption were best suited to Elovich (R2 > 0.98), while pseudo-second-order (R2 > 0.99) for dye removal. Similarly, the two-compartment model also demonstrated better values (R2 > 0.92) for bisphenol-A and dye removal from single and binary solutions with greater Ffast values (except for bisphenol-A in binary solution). The Langmuir isotherm model demonstrated the highest regression coefficient values (R2 > 0.99) for bisphenol-A and dye removal with the highest adsorption capacity of 38.387 mg g-1 and 346.856 mg g-1, correspondingly. Besides, the co-existence of humic acid revealed a positive impact on bisphenol-A removal, while the dye removal rate was slightly hindered in presence of humic acid. The absorption process showed monolayer coverage of biochar surface with contaminants using a chemisorption mechanism with fast reactions between functional groups on the adsorbate and adsorbent. Whereas the adsorption mechanism was primarily controlled by hydrogen bonding, hydrophobic and π-π electron-donor-acceptor interactions as confirmed by FTIR, XPS, and pH investigations.

Gamma aminobutyric acid (GABA) production in Escherichia coli with pyridoxal kinase (pdxY) based regeneration system.

Gamma-aminobutyric acid (GABA) is a non-proteinogenic amino acid act as a major neurotransmitter inhibitor in the nervous system of mammals. It also used as a precursor of bioplastics synthesis such as N-methylpyrolidone and polyamide 4. Chemical-based synthesis methods have many environmental-related issues, so efforts have been made to develop biosynthetic methods to produce GABA. Glutamate decarboxylase (GAD) transforms L-glutamate to GABA using pyridoxal 5'-phosphate (PLP) as a cofactor. Bioconversion of GABA with whole cells overexpressing the glutamate decarboxylase has advantages of fewer byproducts and rapid reaction. However, there is a bottleneck in the whole-cell bioconversion system i.e., higher GABA production require a large amount of cofactor PLP which make the process costly. Therefore, pyridoxal kinase (PdxY) able to regenerate PLP was introduced in the whole-cell system to construct a new GABA producing system. Culture and reaction conditions were optimized, and 100% conversion of 0.6 M MSG was obtained. This study reports that a competitive level of GABA production could be achieved without supplying additional PLPs.

Iron-activated bermudagrass-derived biochar for adsorption of aqueous sulfamethoxazole: Effects of iron impregnation ratio on biochar properties, adsorption, and regeneration.

This work focused on the impacts of FeCl3 impregnation ratio on the properties of FeCl3-activated bermudagrass (BG)-derived biochars (IA-BCs), adsorption of sulfamethoxazole (SMX) onto IA-BCs and regeneration of SMX-spent IA-BC. Compared with the control BC (85.82 m2/g), IA-BCs made via pyrolysis with FeCl3 to BG mass ratio between 1 and 3 (1-3 g FeCl3/g BG) resulted in significantly enhancing surface area (1014-1035 m2/g), hydrophobicity, Fe content in IA-BCs (3.87-7.27%), and graphitized carbon. The properties of IA-BCs supported magnetic separation and higher adsorption (32-265 mg SMX/g BC) than the control BC (6-14 mg SMX/g BC) at various pH. Adsorption experiments indicated various adsorption mechanisms between SMX and IA-BCs via π-π EDA, hydrophobic interactions, and hydrogen bond with intraparticle diffusion limitation. The adsorption was also found to be spontaneous and exothermic. The IA-BC made at FeCl3 to BG mass ratio of 2 (IA-BC2.0) showed the maximum adsorption capacity for SMX (253 mg SMX/g BC) calculated from Langmuir isotherm model. Additionally, both NaOH desorption and thermal oxidation showed effective regeneration of SMX-saturated IA-BC2.0 over multiple cycles. After three cycles of adsorption-regeneration, 64% and 62% of regeneration efficiencies were still achieved under thermal treatment at 300 °C and desorption with 0.1 M NaOH solution, respectively, indicating a cost-efficient adsorbent for the elimination of SMX in water.

Bioprospecting of exopolysaccharide from marine Sphingobium yanoikuyae BBL01: Production, characterization, and metal chelation activity.

In the present study, an exopolysaccharide (EPS)-producing bacterial strain was isolated from the Eastern Sea (Sokcho Beach) of South Korea and identified as Sphingobium yanoikuyae BBL01. Media optimization was performed using response surface design, and a yield of 2.63 ± 0.02 g/L EPS was achieved. Purified EPS produced using lactose as the main carbon source was analyzed by GC-MS and found to be composed of α-D-xylopyranose (28.6 ± 2.0%), ß-D-glucopyranose (21.0 ± 1.6%), α-D-mannopyranose (18.5 ± 1.2%), ß-d-mannopyranose (13.1 ± 1.4%), ß-D-xylopyranose (10.2 ± 2.1%), α-d-talopyranose (5.9 ± 1.1%), and ß-d-galacturonic acid (2.43 ± 0.8%). Interestingly, different carbon sources (glucose, galactose, glycerol, lactose, sucrose, and xylose) showed no effect on EPS monomer composition, with a slight change in the mass percentage of various monosaccharides. Purified EPS was stable up to 233 °C, indicating its possible suitability as a thickening and gelling agent for food-related applications. EPS also showed considerable emulsifying, flocculating, free-radical scavenging, and metal-complexion activity, suggesting various biotechnological applications.

Biowaste-to-bioplastic (polyhydroxyalkanoates): Conversion technologies, strategies, challenges, and perspective.

Biowaste management is a challenging job as it is high in nutrient content and its disposal in open may cause a serious environmental and health risk. Traditional technologies such as landfill, bio-composting, and incineration are used for biowaste management. To gain revenue from biowaste researchers around the world focusing on the integration of biowaste management with other commercial products such as volatile fatty acids (VFA), biohydrogen, and bioplastic (polyhydroxyalkanoates (PHA)), etc. PHA production from various biowastes such as lignocellulosic biomass, municipal waste, waste cooking oils, biodiesel industry waste, and syngas has been reported successfully. Various nutrient factors i.e., carbon and nitrogen source concentration and availability of dissolved oxygen are crucial factors for PHA production. This review is an attempt to summarize the recent advancements in PHA production from various biowaste, its downstream processing, and other challenges that need to overcome making bioplastic an alternate for synthetic plastic.

Methodology: non-invasive monitoring system based on standing wave ratio for detecting water content variations in plants.

BACKGROUND: Water content variation during plant growth is one of the most important monitoring parameters in plant studies. Conventional parameters (such as dry weight) are unreliable; thus, the development of rapid, accurate methods that will allow the monitoring of water content variation in live plants is necessary. In this study, we aimed to develop a non-invasive, radiofrequency-based monitoring system to rapidly and accurately detect water content variation in live plants. The changes in standing wave ratio (SWR) caused by the presence of stem water and magnetic particles in the stem water flow were used as the basis of plant monitoring systems. RESULTS: The SWR of a coil probe was used to develop a non-invasive monitoring system to detect water content variation in live plants. When water was added to the live experimental plants with or without illumination under drought conditions, noticeable SWR changes at various frequencies were observed. When a fixed frequency (1.611 GHz) was applied to a single experimental plant (Radermachera sinica), a more comprehensive monitoring, such as water content variation within the plant and the effect of illumination on water content, was achieved. CONCLUSIONS: Our study demonstrated that the SWR of a coil probe could be used as a real-time, non-invasive, non-destructive parameter for detecting water content variation and practical vital activity in live plants. Our non-invasive monitoring method based on SWR may also be applied to various plant studies.

Morphological and Chemical Evaluations of Leaf Surface on Particulate Matter2.5 (PM2.5) Removal in a Botanical Plant-Based Biofilter System.

Particulate matter has been increasing worldwide causing air pollution and serious health hazards. Owing to increased time spent indoors and lifestyle changes, assessing indoor air quality has become crucial. This study investigated the effect of watering and drought and illumination conditions (constant light, light/dark cycle, and constant dark) on particulate matter2.5 (PM2.5) removal and surface characterization of leaf in a botanical plant-based biofilter system. Using Ardisia japonica and Hedera helix as experimental plants in the plant-based biofilter system, PM2.5, volatile organic carbon, and CO2, as the evaluators of indoor air quality, were estimated using a sensor. Morphological and chemical changes of the leaf surface (i.e., roughness and wax) associated with PM2.5 removal were characterized via scanning electron microscopy, Fourier transform infrared spectroscopy, and atomic force microscopy. The highest PM2.5 removal efficiency, stomata closure, high leaf roughness, and wax layer were observed under drought with constant light condition. Consequently, PM2.5 removal was attributed to the combined effect of leaf roughness and wax by adsorption rather than stomatal uptake. These results suggest that operating conditions of indoor plant-based biofilter system such as watering (or drought) and illumination may be applied as a potential strategy for enhancing PM2.5 removal.