Design of a Deployable Broadband Mesh Reflector Antenna for a SIGINT Satellite System Considering Surface Shape Deformation.

In this paper, we propose a deployable broadband mesh reflector antenna for use in signals intelligence (SIGINT) satellite systems, considering performance degradation due to shape deformation. To maximize gain by increasing the diameter of the reflector while reducing the weight of the antenna, the reflector of the antenna is designed using lightweight silver-coated Teflon mesh. The mesh reflectors are typically expanded by tension to maintain their parabolic structure; thus, shape deformation cannot be avoided. This shape deformation results in shape differences between the surface of the mesh reflector and the ideal parabolic reflector, thus resulting in the degradation of the performance of the mesh reflector antenna. To observe this degradation, we analyze antenna performance according to the number of arms, the number of joints, the feed distance, and the distance from the reflector center to each joint. The performance of the mesh reflector antenna is examined using an effective lossy conducting surface (ELCS) that has the same reflectivity as the silver-coated Teflon mesh to reduce simulation time and computing resources. The designed silver-coated Teflon mesh reflector and the double-ridged feed antenna are fabricated, and the bore-sight gain is measured using the three-antenna method. The measured bore-sight gain of the proposed antenna is 31.6 dBi at 10 GHz, and the measured and simulated results show an average difference of 3.28 dB from 2 GHz to 18 GHz. The proposed deployable mesh reflector antenna can be used in a variety of applications where small stowed volume is required for mobility, such as mobile high-gain antennas as well as satellite antenna systems. Through this study, we demonstrate that shape deformation of the mesh reflector surface significantly affects the performance of reflector antennas.

Design of a Tripod-Shaped Radiator Patch Antenna for Ultra-Wideband Direction Finding.

As UWB technology develops and devices become smaller, miniaturization techniques for an array antenna system are required. In addition, more in-depth research is needed for UWB direction-finding techniques using channel impulse response (CIR) data. This paper proposes an ultra-wideband (UWB) antenna using a single-radiator multiple-port (SRMP) design for the direction-finding systems of smart devices. The proposed SRMP antenna was designed using a single tripod-shaped patch that can replace the array system. The tripod-shaped radiator was optimized using the edge shape design function to improve its broadband and mutual coupling characteristics. For performance verification, the proposed antenna was fabricated, and the reflection coefficient, mutual coupling, and radiation patterns were measured in a fully anechoic chamber. The proposed antenna has an operating frequency band of 6.1 GHz (from 5.8 GHz to 11.9 GHz) for port 1 and a measured mutual coupling of -14.8 dB at 8 GHz. The SRMP antenna has measured maximum gains of 3.5 dBi for port 1 and 2.9 dBi for port 2. To examine the direction-finding performance, the fabricated antenna was connected to a circuit module with a DW3000 chip, which is widely employed in commercial mobile UWB systems. The direction of arrival (DoA) results using the measured CIR data show root-mean-square (RMS) errors of 1.57° and 4.58° at distances of 30 cm and 60 cm.

Design of a mmWave Antenna Printed on a Thick Vehicle-Glass Substrate Using a Linearly Arrayed Patch Director and a Grid-Slotted Patch Reflector for High-Gain Characteristics.

This paper proposes a 5G glass antenna that can be printed on the thick window glass of a vehicle. The proposed antenna consists of a coplanar waveguide (CPW), a printed monopole radiator, parasitic elements, a linearly arrayed patch director, and a grid-slotted patch reflector. The linearly arrayed patch director and grid-slotted patch reflector are applied to improve the bore-sight gain of the antenna. To verify the performance improvement and feasibility, the proposed antenna is fabricated, and a reflection coefficient and a radiation pattern are measured and compared with the simulation results. The measured reflection coefficient shows broadband characteristics of less than -10 dB from 24.1 GHz to 31.0 GHz (fractional bandwidth of 24.6%), which agrees well with the simulation results. The reflection coefficients are -33.1 dB by measurement and -25.7 dB by simulation, and the maximum gains are 6.2 dBi and 5.5 dBi at 28 GHz, respectively. These results demonstrate that the proposed antenna has high-gain characteristics being suitable for 5G wireless communications.

Design of a Novel Wideband Leaf-Shaped Printed Dipole Array Antenna Using a Parasitic Loop for High-Power Jamming Applications.

This paper proposes a novel wideband leaf-shaped printed dipole antenna sensor that uses a parasitic element to improve the impedance matching bandwidth characteristics for high-power jamming applications. The proposed antenna sensor consists of leaf-shaped dipole radiators, matching posts, rectangular slots, and a parasitic loop element. The leaf-shaped dipole radiators are designed with exponential curves to obtain a high directive pattern and are printed on a TLY-5 substrate for high-power durability. The matching posts, rectangular slots, and a parasitic loop element are used to enhance the impedance matching characteristics. The proposed antenna sensor has a measured fractional bandwidth of 66.7% at a center frequency of 4.5 GHz. To confirm the array antenna sensor characteristics, such as its active reflection coefficients (ARCs) and beam steering gains, the proposed single antenna sensor is extended to an 11 × 1 uniform linear array. The average values of the simulated and measured ARCs from 4.5 to 6 GHz are -13.4 dB and -14.7 dB. In addition, the measured bore-sight array gains of the co-polarization are 13.4 dBi and 13.7 dBi at 4 GHz and 5 GHz, while those of the cross-polarizations are -4.9 dBi and -3.4 dBi, respectively. When the beam is steered at a steering angle, θ0, of 15°, the maximum measured array gains of the co-polarization are 12.2 dBi and 10.3 dBi at 4 GHz and 5 GHz, respectively.

Design of a Miniaturized Rectangular Multiturn Loop Antenna for Shielding Effectiveness Measurement.

This paper proposes a novel miniaturized rectangular loop antenna sensor consisting of a multiturn wire and a cuboid ferrite core. The lateral surface of the ferrite core is tightly wound by the multiturn wire. To verify its feasibility, the antenna sensor is fabricated, and the antenna factor (AF) levels are measured using the three-antenna method from the very low frequency (VLF) to the high-frequency (HF) bands. The measured AF levels are 31.8 dB (with a covering plastic case) and 33.1 dB (without a covering plastic case) at 30 kHz. In addition, the proposed antenna is employed in the shielding effectiveness measurement of a small commercial cabinet to observe its suitability for shielding effectiveness (SE) measurement of small shielding enclosures. The SE values averaged over the frequency range from 10 kHz to 3 MHz are 4.1 dB and 12 dB in the horizontal and vertical polarizations, respectively.

Wireless-Powered Chemical Sensor by 2.4 GHz Wi-Fi Energy-Harvesting Metamaterial.

Metamaterial Sensors show significant potential for applications ranging from hazardous chemical detection to biochemical analysis with high-quality sensing properties. However, they require additional measurement systems to analyze the resonance spectrum in real time, making it difficult to use them as a compact and portable sensor system. Herein, we present a novel wireless-powered chemical sensing system by using energy-harvesting metamaterials at microwave frequencies. In contrast to previous studies, the proposed metamaterial sensor utilizes its harvested energy as an intuitive sensing indicator without complicated measurement systems. As the spectral energy-harvesting rate of the proposed metamaterial sensor can be varied by changing the chemical components and their mixtures, we can directly distinguish the chemical species by analyzing the resulting output power levels. Moreover, by using a 2.4 GHz Wi-Fi source, we experimentally realize a prototype chemical sensor system that wirelessly harvests the energy varying from 0 mW up to 7 mW depending on the chemical concentration of the water-based binary mixtures.

New perspective on single-radiator multiple-port antennas for adaptive beamforming applications.

One of the most challenging problems in recent antenna engineering fields is to achieve highly reliable beamforming capabilities in an extremely restricted space of small handheld devices. In this paper, we introduce a new perspective on single-radiator multiple-port (SRMP) antenna to alter the traditional approach of multiple-antenna arrays for improving beamforming performances with reduced aperture sizes. The major contribution of this paper is to demonstrate the beamforming capability of the SRMP antenna for use as an extremely miniaturized front-end component in more sophisticated beamforming applications. To examine the beamforming capability, the radiation properties and the array factor of the SRMP antenna are theoretically formulated for electromagnetic characterization and are used as complex weights to form adaptive array patterns. Then, its fundamental performance limits are rigorously explored through enumerative studies by varying the dielectric constant of the substrate, and field tests are conducted using a beamforming hardware to confirm the feasibility. The results demonstrate that the new perspective of the SRMP antenna allows for improved beamforming performances with the ability of maintaining consistently smaller aperture sizes compared to the traditional multiple-antenna arrays.

Micromachined silicon grisms for infrared optics.

We demonstrate the successful fabrication of large format (approximately 50 mm × 50 mm) gratings in monolithic silicon for use as high-efficiency grisms at infrared wavelengths. The substrates for the grisms were thick (8-16 mm) disks of precisely oriented single-crystal silicon (refractive index, n ~ 3.42). We used microlithography and chemical wet etching techniques to produce the diffraction gratings on one side of these substrates. These techniques permitted the manufacture of coarse grooves (as few as 7 grooves/mm) with precise control of the blaze angle and groove profile and resulted in excellent groove surface quality. Profilometric measurements of the groove structure of the gratings confirm that the physical dimensions of the final devices closely match their design values. Optical performance of these devices exceeds the specifications required for diffraction-limited performance (RMS wave surface error <λ/20) in the near- and mid-infrared (1-40 µm). Peak diffraction efficiencies measured in the reflection range from 70-95% of the theoretical maximum. Tests of our grisms in the near infrared indicate transmission efficiencies of 30-48% uncorrected for Fresnel losses and confirm excellent performance. In infrared wavelength regions where silicon transmits well, the blaze control and high index permit high-resolution, high-order dispersion in a compact space. The first application of these grisms is to provide FORCAST, a mid-infrared camera on NASA's airborne observatory, with a moderate resolution (R=100-1000) spectroscopic capability.