Tunable channel drop filters consisting of a tilted Bragg grating and a mode sorting polymer waveguide.

Optical wavelength filters with large tuning range and narrow bandwidth are crucial for enhancing the capability of WDM communication systems. A polymeric tunable filter for C-band, comprising a tilted Bragg grating and a mode sorting waveguide junction is proposed in this work. For dropping a certain wavelength signal, the tilted Bragg grating reflects an odd mode into an even mode and then the reflected even mode propagates towards an output port of the asymmetric Y-junction due to the mode sorting. Consequently, the output port is separated from the input port, which is not possible in an ordinary Bragg reflector. The tilted Bragg reflector with an odd-even mode coupling efficiency of 61% exhibited a maximum reflectivity of 95% for a grating of 6 mm. A linear wavelength tuning of over 10 nm was achieved for an applied thermal power of 312 mW.

Integrated-optic current sensors with a multimode interference waveguide device.

Optical current sensors based on polarization-rotated reflection interferometry are demonstrated using polymeric integrated optics and various functional optical waveguide devices. Interferometric sensors normally require bias feedback control for maintaining the operating point, which increases the cost. In order to resolve this constraint of feedback control, a multimode interference (MMI) waveguide device is integrated onto the current-sensor optical chip in this work. From the multiple outputs of the MMI, a 90° phase-shifted transfer function is obtained. Using passive quadrature demodulation, we demonstrate that the sensor could maintain the output signal regardless of the drift in the operating bias-point.

Integrated optic polarization splitter based on total internal reflection from a birefringent polymer.

An integrated optic polarization splitter with large fabrication tolerance and high reliability is required for optical signal processing in quantum-encrypted communication systems. A polarization splitter based on total internal reflection from a highly birefringent polymer-reactive mesogen-is proposed and demonstrated in this work. The device consists of a mode expander for reducing the wave vector distribution of the guided mode, and an interface with a large birefringence. Several polymers with suitable refractive indexes were used for fabricating the device. We obtained a polarization splitter with a low crosstalk (less than -30 dB), and a large fabrication tolerance.

Integrated optic current transducers incorporating photonic crystal fiber for reduced temperature dependence.

Optical current transducers (OCT) are indispensable for accurate monitoring of large electrical currents in an environment suffering from severe electromagnetic interference. Temperature dependence of OCTs caused by its components, such as wave plates and optical fibers, should be reduced to allow temperature-independent operation. A photonic crystal fiber with a structural optical birefringence was incorporated instead of a PM fiber, and a spun PM fiber was introduced to overcome the temperature-dependent linear birefringence of sensing fiber coil. Moreover, an integrated optic device that provides higher stability than fiber-optics was employed to control the polarization and detect the phase of the sensed optical signal. The proposed OCT exhibited much lower temperature dependence than that from a previous study. The OCT satisfied the 0.5 accuracy class (IIEC 60044-8) and had a temperature dependence less than ± 1% for a temperature range of 25 to 78 °C.

Tunable channel-drop filters consisting of polymeric Bragg reflectors and a mode sorting asymmetric X-junction.

A tunable channel-drop filter as essential component for the wavelength-division-multiplexing optical communication system has been demonstrated, which is based on polymer waveguide Bragg reflectors. For an ordinary Bragg reflector, the filtered signal is reflected toward the input waveguide. Thus an external circulator is required to separate the filtered signal from the input port, though it increases the total footprint and cost. For this purpose, we employed dual Bragg reflectors and a mode sorting asymmetric X-junction. The Bragg reflector exhibited a maximum reflectivity of 94% for a 6-mm long grating, a 3-dB bandwidth of 0.39 nm and a 20-dB bandwidth of 2.6 nm. The mode sorting crosstalk in asymmetric X-junction was less than -20 dB, and linear wavelength tuning was achieved over 10 nm at the applied thermal power of 377 mW.

Surface relief apodized grating tunable filters produced by using a shadow mask.

To produce a compact low-cost tunable filter required for WDM optical communications, a polymeric Bragg reflection filter with an apodized grating structure is proposed. A high-contrast polymeric waveguide is incorporated in order to obtain high reflectivity from a short Bragg grating. To overcome the bandwidth broadening, an apodized grating with a gradually changing depth of surface relief grating along the propagation direction is fabricated through the dry etching with a shadow mask. The apodized polymer grating exhibits 3-dB, 20-dB bandwidths of 0.36 nm, and 0.72 nm, respectively with a 95% reflection. The reflection wavelength is tunable over 14 nm for an applied thermal power of 500 mW.

Arrayed waveguide collimators for integrating free-space optics on polymeric waveguide devices.

Array-type optical devices are important for wavelength-division multiplexing optical communication system to achieve small footprint, mass production, and reliability. For fabricating transmitter module in an array configuration, it is difficult to achieve a passive alignment of isolator, collimating lens, and laser diode. To facilitate array isolator integration, a waveguide collimator is proposed in this work by using a low-contrast, large-core polymer waveguide. The diffraction of a guided mode propagating through a free-space region is suppressed by enlarging the guided mode. The fiber coupling loss due to the enlarged mode was overcome by incorporating an adiabatic taper structure. The excess loss of waveguide collimator including the loss through a 400-µm free-propagation region was less than 1.0 dB.

Low-crosstalk high-density polymeric integrated optics incorporating self-assembled scattering monolayer.

Highly integrated optical components are strongly demanded because they enable wavelength-division multiplexing optical communication systems to achieve smaller footprints, lower power consumption, and enhanced reliability. Variable optical attenuator (VOA) arrays are often used with optical switches in cascaded form for reconfigurable optical add-drop multiplexer systems. Although VOAs and optical switches based on polymer waveguide technology are commercially available, it is still not viable to integrate these two array devices on a single chip because of significant interchannel crosstalk. In this work, we resolved the issue of crosstalk and integrated the arrays of optical switch and VOA on a single chip by incorporating a self-assembled scattering monolayer (SASM). The SASM was effective for scattering the planar guided mode; consequently, the crosstalk into an adjacent channel was significantly reduced, to less than -35 dB.

Integrated-optic polarization controllers incorporating polymer waveguide birefringence modulators.

Polarization controllers based on polymer waveguide technology are demonstrated by incorporating thermo-optic birefringence modulators (BMs) and thin-film wave plates. Highly birefringent polymer materials are used to increase the efficiency of birefringence modulation in proportion to the heating power. Thin-film quarter-wave plates are fabricated by using a crosslinkable liquid crystal, reactive mesogen, and inserted between the BMs to produce static phase retardation and polarization coupling. By applying a triangular AC signal to one BM and a DC signal to another, the polarization states of the output light are modulated to cover the entire surface of the Poincaré sphere.

Polymer waveguide integrated-optic current transducers.

Various functional optical devices are integrated on a single chip in order to construct optical current transducers based on polarization rotated reflection interferometry, which consists of polarization maintaining 3-dB couplers, TE-pass polarizers, TE/TM polarization converters, and thermo-optic phase modulators. By virtue of the device integration, the sensor exhibited good linearity, and excellent accuracy with an error less than 0.2%. The integrated-optic device provides inherent polarization maintaining characteristics and precise controllability of the optical path length in the interferometric sensor. Single chip integration reduces the complexity of the interferometry, and enables mass-production of low-cost high performance current sensors.