Recycling and characterization of carbon fibers from carbon fiber reinforced epoxy matrix composites by a novel super-heated-steam method.

In order to manufacture high quality recycled carbon fibers (R-CFs), carbon fiber-reinforced composite wastes were pyrolysed with super-heated steam at 550 °C in a fixed bed reactor for varying reaction times. The mechanical and surface properties of the R-CFs were characterized with a single fiber tensile test, interface shear strength (IFSS), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The surface analysis showed that there was no matrix char residue on the fiber surfaces. The tensile strength and IFSS values of the R-CFs were 90% and 115% compared to those of virgin carbon fibers (V-CFs), respectively. The recycling efficiency of the R-CFs from the composites were strongly dependent on the pyrolysis temperature, reaction time, and super-heated steam feeding rate.

CO2 Adsorption Behaviors of Biomass-Based Activated Carbons Prepared by a Microwave/Steam Activation Technique for Molecular Sieve.

In this study, the activated carbon was prepared with superior CO2 selective adsorption properties using walnut shells, a biomass waste, as a precursor. The activations were conducted at various times using the microwave heating technique in a steam atmosphere. The surface morphology and chemical composition of activated carbon were analyzed using a scanning electron microscope and energy-dispersive X-ray spectroscopy. The textural properties were investigated using the N2/77K isothermal method, and the structural characteristics were examined using X-ray diffraction analysis. The CO2 and H2 adsorption properties of activated carbon were analyzed using a thermogravimetric analyzer and a high-pressure isothermal adsorption apparatus, respectively, under atmospheric and high-pressure conditions. Depending on the activation time, the specific surface area and total pore volume of the activated carbon were 570-690 m2/g and 0.26-0.34 cm3/g, respectively. The adsorption behaviors of CO2 of the activated carbon were different under atmospheric and high-pressure conditions. At atmospheric pressure, a significant dependence on micropores with diameters less than 0.8 nm was observed, whereas, at high pressure, the micropores and mesopores in the range of 1.6-2.4 nm exhibited a significant dependence. However, H2 adsorption did not occur at relatively low pressures. Consequently, the prepared activated carbon exhibited superior selective adsorption properties for CO2.

Bamboo-Based Mesoporous Activated Carbon for High-Power-Density Electric Double-Layer Capacitors.

Demand for hybrid energy storage systems is growing, but electric double-layer capacitors (EDLCs) have insufficient output characteristics because of the microporous structure of the activated carbon electrode material. Commercially, activated carbon is prepared from coconut shells, which yield an activated carbon material (YP-50F) rich in micropores, whereas mesopores are desired in EDLCs. In this study, we prepared mesoporous activated carbon (PB-AC) using a readily available, environmentally friendly resource: bamboo. Crucially, modification using phosphoric acid and steam activation was carried out, which enabled the tuning of the crystal structure and the pore characteristics of the product. The structural characteristics and textural properties of the PB-AC were determined, and the specific surface area and mesopore volume ratio of the PB-AC product were 960-2700 m2/g and 7.5-44.5%, respectively. The high specific surface area and mesopore-rich nature originate from the phosphoric acid treatment. Finally, PB-AC was used as the electrode material in EDLCs, and the specific capacitance was found to be 86.7 F/g for the phosphoric-acid-treated sample steam activated at 900 °C for 60 min; this capacitance is 35% better than that of the commercial YP-50F (64.2 F/g), indicating that bamboo is a suitable material for the production of activated carbon.

Effect of Mesopore Development on Butane Working Capacity of Biomass-Derived Activated Carbon for Automobile Canister.

Kenaf-derived activated carbons (AKC) were prepared by H3PO4 activation for automobile canisters. The microstructural properties of AKC were observed using Raman spectra and X-ray diffraction. The textural properties were studied using N2/77 K adsorption isotherms. Butane working capacity was determined according to the ASTM D5228. From the results, the specific surface area and total pore volume of the AKC was determined to be 1260-1810 m2/g and 0.68-2.77 cm3/g, respectively. As the activation time increased, the butane activity and retentivity of the AKC increased, and were observed to be from 32.34 to 58.81% and from 3.55 to 10.12%, respectively. The mesopore ratio of activated carbon increased with increasing activation time and was observed up to 78% at 973 K. This indicates that butane activity and retentivity could be a function not only of the specific surface area or total pore volume, but also of the mesopore volume fraction in the range of 2.8-3.8 nm and 5.5-6.5 nm of adsorbents, respectively. The AKC exhibit enhanced butane working capacity compared to commercial activated carbon with the high performance of butane working capacity due to its pore structure having a high mesopore ratio.

Flower-Like Internal Emission Distribution of LEDs with Monolithic Integration of InGaN-based Quantum Wells Emitting Narrow Blue, Green, and Red Spectra.

We report a phosphor-free white light-emitting diodes (LED) realized by the monolithic integration of In0.18Ga0.82N/GaN (438 nm, blue), In0.26Ga0.74N/GaN (513 nm, green), and In0.45Ga0.55N/In0.13Ga0.87N (602 nm, red) quantum wells (QWs) as an active medium. The QWs corresponding to blue and green light were grown using a conventional growth mode. For the red spectral emission, five-stacked In0.45Ga0.55N/In0.13Ga0.87N QWs were realized by the so-called Ga-flow-interruption (Ga-FI) technique, wherein the Ga supply was periodically interrupted during the deposition of In0.3Ga0.7N to form an In0.45Ga0.55N well. The vertical and lateral distributions of the three different light emissions were investigated by fluorescence microscope (FM) images. The FM image measured at a focal point in the middle of the n-GaN cladding layer for the red-emitting LED shows that light emissions with flower-like patterns with six petals are periodically observed. The chromaticity coordinates of the electroluminescence spectrum for the white LEDs at an injection current of 80 mA are measured to be (0.316, 0.312), which is close to ideal white light. In contrast with phosphor-free white-light-emitting devices based on nanostructures, our white light device exhibits a mixture of three independent wavelengths by monolithically grown InGaN-based QWs, thus demonstrating a more facile technique to obtain white LEDs.