Near Room Temperature Production of Segregated Network Composites of Carbon Nanotubes and Regolith as Multifunctional, Extra-Terrestrial Building Materials.

Constructing a semi-permanent base on the moon or Mars will require maximal use of materials found in situ and minimization of materials and equipment transported from Earth. This will mean a heavy reliance on regolith (Lunar or Marian soil) and water, supplemented by small quantities of additives fabricated on Earth. Here it is shown that SiO2-based powders, as well as Lunar and Martian regolith simulants, can be fabricated into building materials at near-ambient temperatures using only a few weight-percent of carbon nanotubes as a binder. These composites have compressive strength and toughness up to 100 MPa and 3 MPa respectively, higher than the best terrestrial concretes. They are electrically conductive (>20 S m-1) and display an extremely large piezoresistive response (gauge factor >600), allowing these composites to be used as internal sensors to monitor the structural health of extra-terrestrial buildings.

High Selectivity and Sensitivity in Chemiresistive Sensing of Co(II) Ions with Liquid-Phase Exfoliated Functionalized MoS2 : A Supramolecular Approach.

Chemical sensing of water contamination by heavy metal ions is key as it represents a most severe environmental problem. Liquid-phase exfoliated two-dimensional (2D) transition metal dichalcogenides (TMDs) are suitable candidates for chemical sensing thanks to their high surface-to-volume ratio, sensitivity, unique electrical characteristics, and scalability. However, TMDs lack selectivity due to nonspecific analyte-nanosheet interactions. To overcome this drawback, defect engineering enables controlled functionalization of 2D TMDs. Here, ultrasensitive and selective sensors of cobalt(II) ions via the covalent functionalization of defect-rich MoS2 flakes with a specific receptor, 2,2':6',2″-terpyridine-4'-thiol is developed. A continuous network is assembled by healing of MoS2 sulfur vacancies in a tailored microfluidic approach, enabling high control over the assembly of thin and large hybrid films. The Co2+ cations complexation represents a powerful gauge for low concentrations of cationic species which can be best monitored in a chemiresisitive ion sensor, featuring a 1 pm limit of detection, sensing in a broad concentration range (1 pm - 1 µm) and sensitivity as high as 0.308 ± 0.010 lg([Co2+ ])-1 combined with a high selectivity towards Co2+ over K+ , Ca2+ , Mn2+ , Cu2+ , Cr3+ , and Fe3+ cations. This supramolecular approach based on highly specific recognition can be adapted for sensing other analytes through specific ad-hoc receptors.

Solution-Processed Heterojunction Photodiodes Based on WSe2 Nanosheet Networks.

Solution-processed photodetectors incorporating liquid-phase-exfoliated transition metal dichalcogenide nanosheets are widely reported. However, previous studies mainly focus on the fabrication of photoconductors, rather than photodiodes which tend to be based on heterojunctions and are harder to fabricate. Especially, there are rare reports on introducing commonly used transport layers into heterojunctions based on nanosheet networks. In this study, a reliable solution-processing method is reported to fabricate heterojunction diodes with tungsten selenide (WSe2 ) nanosheets as the optical absorbing material and PEDOT: PSS and ZnO as injection/transport-layer materials. By varying the transport layer combinations, the obtained heterojunctions show rectification ratios of up to ≈104 at ±1 V in the dark, without relying on heavily doped silicon substrates. Upon illumination, the heterojunction can be operated in both photoconductor and photodiode modes and displays self-powered behaviors at zero bias.

Highly Conductive Networks of Silver Nanosheets.

Although printed networks of semiconducting nanosheets have found success in a range of applications, conductive nanosheet networks are limited by low conductivities (<106 S m-1 ). Here, dispersions of silver nanosheets (AgNS) that can be printed into highly conductive networks are described. Using a commercial thermal inkjet printer, AgNS patterns with unannealed conductivities of up to (6.0 ± 1.1) × 106  S m-1 are printed. These networks can form electromagnetic interference shields with record shielding effectiveness of >60 dB in the microwave region at thicknesses <200 nm. High resolution patterns with line widths down to 10 µm are also printed using an aerosol-jet printer which, when annealed at 200 °C, display conductivity >107  S m-1 . Unlike conventional Ag-nanoparticle inks, the 2D geometry of AgNS yields smooth, short-free interfaces between electrode and active layer when used as the top electrode in vertical nanosheet heterostructures. This shows that all-printed vertical heterostructures of AgNS/WS2 /AgNS, where the top electrode is a mesh grid, function as photodetectors demonstrating that such structures can be used in optoelectronic applications that usually require transparent conductors.

Liquid Processing of Interfacially Grown Iron-Oxide Flowers into 2D-Platelets Yields Lithium-Ion Battery Anodes with Capacities of Twice the Theoretical Value.

Iron oxide (Fe2 O3 ) is an abundant and potentially low-cost material for fabricating lithium-ion battery anodes. Here, the growth of α-Fe2 O3 nano-flowers at an electrified liquid-liquid interface is demonstrated. Sonication is used to convert these flowers into quasi-2D platelets with lateral sizes in the range of hundreds of nanometers and thicknesses in the range of tens of nanometers. These nanoplatelets can be combined with carbon nanotubes to form porous, conductive composites which can be used as electrodes in lithium-ion batteries. Using a standard activation process, these anodes display good cycling stability, reasonable rate performance and low-rate capacities approaching 1500 mAh g-1 , consistent with the current state-of-the-art for Fe2 O3 . However, by using an extended activation process, it is found that the morphology of these composites can be significantly changed, rendering the iron oxide amorphous and significantly increasing the porosity and internal surface area. These morphological changes yield anodes with very good cycling stability and low-rate capacity exceeding 2000 mAh g-1 , which is competitive with the best anode materials in the literature. However, the data implies that, after activation, the iron oxide displays a reduced solid-state lithium-ion diffusion coefficient resulting in somewhat degraded rate performance.

Printable G-Putty for Frequency- and Rate-Independent, High-Performance Strain Sensors.

While nanocomposite electromechanical sensors are expected to display reasonable conductivity and high sensitivity, little consideration is given to eliminating hysteresis and strain rate/frequency dependence from their response. For example, while G-putty, a composite of graphene and polysiloxane, has very high electromechanical sensitivity, its extreme viscoelasticity renders it completely unsuitable for real sensors due to hysteretic and rate-/frequency-dependent effects. Here it is shown that G-putty can be converted to an ink and printed into patterned thin films on elastic substrates. A partial graphene-polymer phase segregation during printing increases the thin-film conductivity by ×106 compared to bulk, while the mechanical effects of the substrate largely suppress hysteresis and completely remove strain rate and frequency dependence. This allows the fabrication of practical, high-gauge-factor, wearable sensors for pulse measurements as well as patterned sensors for low-signal vibration sensing.

Tuning the Photo-electrochemical Performance of RuII -Sensitized Two-Dimensional MoS2.

Covalently tethering photosensitizers to catalytically active 1T-MoS2 surfaces holds great promise for the solar-driven hydrogen evolution reaction (HER). Herein, we report the preparation of two new RuII -complex-functionalized MoS2 hybrids [RuII (bpy)2 (phen)]-MoS2 and [RuII (bpy)2 (py)Cl]-MoS2 . The influence of covalent functionalization of chemically exfoliated 1T-MoS2 with coordinating ligands and RuII complexes on the HER activity and photo-electrochemical performance of this dye-sensitized system was studied systematically. We find that the photo-electrochemical performance of this RuII -complex-sensitized MoS2 system is highly dependent on the surface extent of photosensitizers and the catalytic activity of functionalized MoS2 . The latter was strongly affected by the number and the kind of functional groups. Our results underline the tunability of the photovoltage generation in this dye-sensitized MoS2 system by manipulation of the surface functionalities, which provides a practical guidance for smart design of future dye-sensitized MoS2 hydrogen production devices towards improved the photofuel conversion efficiency.

Mechanochromic and Thermochromic Sensors Based on Graphene Infused Polymer Opals.

High quality opal-like photonic crystals containing graphene are fabricated using evaporation-driven self-assembly of soft polymer colloids. A miniscule amount of pristine graphene within a colloidal crystal lattice results in the formation of colloidal crystals with a strong angle-dependent structural color and a stop band that can be reversibly shifted across the visible spectrum. The crystals can be mechanically deformed or can reversibly change color as a function of their temperature, hence their sensitive mechanochromic and thermochromic response make them attractive candidates for a wide range of visual sensing applications. In particular, it is shown that the crystals are excellent candidates for visual strain sensors or integrated time-temperature indicators which act over large temperature windows. Given the versatility of these crystals, this method represents a simple, inexpensive, and scalable approach to produce multifunctional graphene infused synthetic opals and opens up exciting applications for novel solution-processable nanomaterial based photonics.

RuII Photosensitizer-Functionalized Two-Dimensional MoS2 for Light-Driven Hydrogen Evolution.

Metallic-phase molybdenum disulfide (1T-MoS2 ) nanosheets have proven to be highly active in the hydrogen evolution reaction (HER). We describe construction of photosensitizer functionalized 1T-MoS2 by covalently tethering the molecular photosensitizer [RuII (bpy)3 ]2+ (bpy=2,2'-bipyridine) on 1T-MoS2 nanosheets. This was achieved by covalently tethering the bpy ligand to 1T-MoS2 nanosheets, and subsequent complexation with [RuII (bpy)2 Cl2 ] to yield [RuII (bpy)3 ]-MoS2 . The obtained [RuII (bpy)3 ]-MoS2 nanosheets were characterized using infra-red, electronic absorption, X-ray photoelectron, and Raman spectroscopies, X-ray powder diffraction and electron microscopy. The fabricated material exhibited a significant improvement of photocurrent and HER performance, demonstrating the potential of such two-dimensional [RuII (bpy)3 ]-MoS2 constructs in photosensitized HER.

Enabling Flexible Heterostructures for Li-Ion Battery Anodes Based on Nanotube and Liquid-Phase Exfoliated 2D Gallium Chalcogenide Nanosheet Colloidal Solutions.

2D metal chalcogenide (MC) nanosheets (NS) have displayed high capacities as lithium-ion battery (LiB) anodes. Nevertheless, their complicated synthesis routes coupled with low electronic conductivity greatly limit them as promising LiB electrode material. Here, this work reports a facile single-walled carbon nanotube (SWCNT) percolating strategy for efficiently maximizing the electrochemical performances of gallium chalcogenide (GaX, X = S or Se). Multiscaled flexible GaX NS/SWCNT heterostructures with abundant voids for Li+ diffusion are fabricated by embedding the liquid-exfoliated GaX NS matrix within a SWCNT-percolated network; the latter improves the electron transport and ion diffusion kinetics as well as maintains the mechanical flexibility. Consequently, high capacities (i.e., 838 mAh g-1 per gallium (II) sulfide (GaS) NS/SWCNT mass and 1107 mAh g-1 per GaS mass; the latter is close to the theoretical value) and good rate capabilities are achieved, which can be majorly attributed to the alloying processes of disordered Ga formed after the first irreversible GaX conversion reaction, as monitored by in situ X-ray diffraction. The presented approach, colloidal solution processing of SWCNT and liquid-exfoliated MC NS to produce flexible paper-based electrode, could be generalized for wearable energy storage devices with promising performances.

Production of Two-Dimensional Nanomaterials via Liquid-Based Direct Exfoliation.

Tremendous efforts have been devoted to the synthesis and application of two-dimensional (2D) nanomaterials due to their extraordinary and unique properties in electronics, photonics, catalysis, etc., upon exfoliation from their bulk counterparts. One of the greatest challenges that scientists are confronted with is how to produce large quantities of 2D nanomaterials of high quality in a commercially viable way. This review summarizes the state-of-the-art of the production of 2D nanomaterials using liquid-based direct exfoliation (LBE), a very promising and highly scalable wet approach for synthesizing high quality 2D nanomaterials in mild conditions. LBE is a collection of methods that directly exfoliates bulk layered materials into thin flakes of 2D nanomaterials in liquid media without any, or with a minimum degree of, chemical reactions, so as to maintain the high crystallinity of 2D nanomaterials. Different synthetic methods are categorized in the following, in which material characteristics including dispersion concentration, flake thickness, flake size and some applications are discussed in detail. At the end, we provide an overview of the advantages and disadvantages of such synthetic methods of LBE and propose future perspectives.

Understanding the Dispersion and Assembly of Bacterial Cellulose in Organic Solvents.

The constituent nanofibrils of bacterial cellulose are of interest to many researchers because of their purity and excellent mechanical properties. Mechanisms to disrupt the network structure of bacterial cellulose (BC) to isolate bacterial cellulose nanofibrils (BCN) are limited. This work focuses on liquid-phase dispersions of BCN in a range of organic solvents. It builds on work to disperse similarly intractable nanomaterials, such as single-walled carbon nanotubes, where optimum dispersion is seen for solvents whose surface energies are close to the surface energy of the nanomaterial; bacterial cellulose is shown to disperse in a similar fashion. Inverse gas chromatography was used to determine the surface energy of bacterial cellulose, under relevant conditions, by quantifying the surface heterogeneity of the material as a function of coverage. Films of pure BCN were prepared from dispersions in a range of solvents; the extent of BCN exfoliation is shown to have a strong effect on the mechanical properties of BC films and to fit models based on the volumetric density of nanofibril junctions. Such control offers new routes to producing robust cellulose films of bacterial cellulose nanofibrils.

Sub-5 nm graphene nanopore fabrication by nitrogen ion etching induced by a low-energy electron beam.

A flexible and efficient method to fabricate nanopores in graphene has been developed. A focused, low-energy (5 keV) electron beam was used to locally activate etching of a graphene surface in a low pressure (0.3 Pa) N2 environment. Nanopores with sub-5 nm diameters were fabricated. The lattice structure of the graphene was observed to recover within 20 nm of the nanopore edge. Nanopore growth rates were investigated systematically. The effects of nitrogen pressure, electron beam dwell time and beam current were characterised in order to understand the etching mechanism and enable optimisation of the etching parameters. A model was developed which describes how the diffusion of ionised nitrogen affects the nanopore growth rate. Etching of other two-dimensional materials was attempted as demonstrated with MoS2. The lack of etching observed supports our model of a chemical reaction-based mechanism. The understanding of the etching mechanism will allow more materials to be etched by selection of an appropriate ion species.

Highly Conductive Graphene and Polyelectrolyte Multilayer Thin Films Produced From Aqueous Suspension.

Rapid, large-scale exfoliation of graphene in water has expanded its potential for use outside niche applications. This work focuses on utilizing aqueous graphene dispersions to form thin films using layer-by-layer processing, which is an effective method to produce large-area coatings from water-based solutions of polyelectrolytes. When layered with polyethyleneimine, graphene flakes stabilized with cholate are shown to be capable of producing films thinner than 100 nm. High surface coverage of graphene flakes results in electrical conductivity up to 5500 S m-1 . With the relative ease of processing, the safe, cost effective nature of the ingredients, and the scalability of the deposition method, this system should be industrially attractive for producing thin conductive films for a variety of electronic and antistatic applications.

Nanopatterning and Electrical Tuning of MoS2 Layers with a Subnanometer Helium Ion Beam.

We report subnanometer modification enabled by an ultrafine helium ion beam. By adjusting ion dose and the beam profile, structural defects were controllably introduced in a few-layer molybdenum disulfide (MoS2) sample and its stoichiometry was modified by preferential sputtering of sulfur at a few-nanometer scale. Localized tuning of the resistivity of MoS2 was demonstrated and semiconducting, metallic-like, or insulating material was obtained by irradiation with different doses of He(+). Amorphous MoSx with metallic behavior has been demonstrated for the first time. Fabrication of MoS2 nanostructures with 7 nm dimensions and pristine crystal structure was also achieved. The damage at the edges of these nanostructures was typically confined to within 1 nm. Nanoribbons with widths as small as 1 nm were reproducibly fabricated. This nanoscale modification technique is a generalized approach that can be applied to various two-dimensional (2D) materials to produce a new range of 2D metamaterials.

White Graphene undergoes Peroxidase Degradation.

Hexagonal boron nitride (hBN) nanosheets are emerging as promising 2D materials for different types of applications. However, biodegradation of hBN materials is poorly explored owing to their high chemical inertness and strong oxidation resistance. The assessment of oxidation/biodegradation of hBN is important in developing biomedical tools. Herein, we report the first study on the biodegradability of hBN nanosheets comparing the enzymatic catalysis of two different peroxidases, horseradish peroxidase (HRP) and human myeloperoxidase (MPO), with the photo-Fenton (P.F.) reaction. The results show that degradation of hBN nanosheets is different to that of graphene and graphene oxide, since partial oxidation was found using MPO after 35 h, while HRP failed to degrade hBN up to 60 days. Nearly complete oxidation/degradation was occurred by P.F. reaction in 100 h. These results are helpful in designing advanced conjugates for biomedical uses of hBN.

Scalable production of large quantities of defect-free few-layer graphene by shear exfoliation in liquids.

To progress from the laboratory to commercial applications, it will be necessary to develop industrially scalable methods to produce large quantities of defect-free graphene. Here we show that high-shear mixing of graphite in suitable stabilizing liquids results in large-scale exfoliation to give dispersions of graphene nanosheets. X-ray photoelectron spectroscopy and Raman spectroscopy show the exfoliated flakes to be unoxidized and free of basal-plane defects. We have developed a simple model that shows exfoliation to occur once the local shear rate exceeds 10(4) s(-1). By fully characterizing the scaling behaviour of the graphene production rate, we show that exfoliation can be achieved in liquid volumes from hundreds of millilitres up to hundreds of litres and beyond. The graphene produced by this method performs well in applications from composites to conductive coatings. This method can be applied to exfoliate BN, MoS2 and a range of other layered crystals.

Yielding and flow of highly concentrated, few-layer graphene suspensions.

For a wide range of applications of graphene suspensions, a thorough understanding of their rheological properties is crucial. We probe the microstructure of dense suspensions of micron-sized, few-layer, defect-free graphene platelets by measuring their viscoelastic properties at various concentrations up to 39 mg ml(-1). We propose a model to relate the yield strain to the mesh size of the microstructure as a function of volume fraction ϕ. From the yield stress measurements we infer the typical bond energy (≈20 kBT) and ϕ dependence of the bond number density. These results allow us to express the steady shear viscosity for Peclet number Pe < 10 in terms of the platelet dimensions, bond energy and ϕ using a relaxation ansatz.

Functionalization of liquid-exfoliated two-dimensional 2H-MoS2.

Layered two-dimensional (2D) inorganic transition-metal dichalchogenides (TMDs) have attracted great interest as a result of their potential application in optoelectronics, catalysis, and medicine. However, methods to functionalize and process such 2D TMDs remain scarce. We have established a facile route towards functionalized layered MoS2 . We found that the reaction of liquid-exfoliated 2D MoS2 , with M(OAc)2 salts (M=Ni, Cu, Zn; OAc=acetate) yielded functionalized MoS2 -M(OAc)2 materials. Importantly, this method furnished the 2H-polytype of MoS2 which is a semiconductor. X-ray photoelectron spectroscopy (XPS), diffuse reflectance infrared Fourier transform spectroscopy (DRIFT-IR), and thermogravimetric analysis (TGA) provide strong evidence for the coordination of MoS2 surface sulfur atoms to the M(OAc)2 salt. Interestingly, functionalization of 2H-MoS2 allows for its dispersion/processing in more conventional laboratory solvents.

Liquid exfoliation of defect-free graphene.

Due to its unprecedented physical properties, graphene has generated huge interest over the last 7 years. Graphene is generally fabricated in one of two ways: as very high quality sheets produced in limited quantities by micromechanical cleavage or vapor growth or as a rather defective, graphene-like material, graphene oxide, produced in large quantities. However, a growing number of applications would profit from the availability of a method to produce high-quality graphene in large quantities. This Account describes recent work to develop such a processing route inspired by previous theoretical and experimental studies on the solvent dispersion of carbon nanotubes. That work had shown that nanotubes could be effectively dispersed in solvents whose surface energy matched that of the nanotubes. We describe the application of the same approach to the exfoliation of graphite to give graphene in a range of solvents. When graphite powder is exposed to ultrasonication in the presence of a suitable solvent, the powder fragments into nanosheets, which are stabilized against aggregation by the solvent. The enthalpy of mixing is minimized for solvents with surface energies close to that of graphene (∼68 mJ/m(2)). The exfoliated nanosheets are free of defects and oxides and can be produced in large quantities. Once solvent exfoliation is possible, the process can be optimized and the nanosheets can be separated by size. The use of surfactants can also stabilize exfoliated graphene in water, where the ζ potential of the surfactant-coated graphene nanosheets controls the dispersed concentration. Liquid exfoliated graphene can be used for a range of applications: graphene dispersions as optical limiters, films of graphene flakes as transparent conductors or sensors, and exfoliated graphene as a mechanical reinforcement for polymer-based composites. Finally, we have extended this process to exfoliate other layered compounds such as BN and MoS(2). Such materials will be important in a range of applications from thermoelectrics to battery electrodes. This liquid exfoliation technique can be applied to a wide range of materials and has the potential to be scaled up into an industrial process. We believe the coming decade will see an explosion in the applications involving liquid exfoliated two-dimensional materials.