RESUMEN
The microstructures on a diamond surface have attracted extensive attention in microelectronics, ultra-precision machining tools, and optical elements, etc. In this work, microgrooves were fabricated on a single-crystal diamond surface using ultraviolet nanosecond or infrared picosecond laser pulses. The surface and internal morphologies of the microgrooves were characterized. The chemical composition and phase transition of the diamond after laser irradiation were analyzed. Furthermore, the ablation threshold, ablation rate, and material removal rate of the diamond processed by nanosecond or picosecond lasers were also calculated. In addition, the temperature distributions of the diamond ablated by nanosecond or picosecond lasers were simulated. Finally, the material removal mechanisms of a single-crystal diamond processed by nanosecond or picosecond lasers were revealed. This work is expected helpful to provide a guidance for the laser fabrication of microstructures on diamond.
RESUMEN
A spectroscopic Mueller matrix ellipsometer based on two rotating Fresnel rhomb compensators with a nearly achromatic response and optimal retardance is described. In this instrument, the compensators rotate in a discrete manner instead of continuously rotating, and this allows for a well-conditioned measurement even for low intensity samples. Moreover, in this configuration, the exposure time of the CCD detector can be varied within orders of magnitude without interfering with the dynamics of the compensator rotation. An optimization algorithm determines the optimal set of discrete angles that allows the determination of the Mueller matrix in the presence of noise. The calibration of the instrument is discussed, and examples of experimentally determined Mueller matrices are provided.
RESUMEN
In this work, we derive closed-form expressions for determination of the linear birefringence and linear dichroism of uniaxial crystals utilizing transmission ellipsometry measurements at small angles of incidence in $ c $c-cut crystal substrates. The model-free method we use is an algebraic generalization of the method reported in Appl. Opt.44, 3153 (2005).APOPAI0003-693510.1364/AO.44.003153 The optical anisotropy of substrates of sapphire, 4H-SiC, and 6H-SiC single crystals is measured for illustration.
RESUMEN
In this paper, a new method for measuring the thickness of transparent specimens using chromatic confocal microscopy (CCM) is presented. The conventional CCM thickness measurement model relies on capturing the focal points on the upper and lower surfaces of a transparent specimen. This model has strict specimen placement tolerance and a limited measurement range. In order to overcome these limitations, a new thickness measurement model was developed by adding an auxiliary reflector below the specimen. The thickness of the specimen can be determined by comparing the wavelengths of light focused on the auxiliary reflector before and after placing the measurement specimen. Theoretical analysis and simulation showed that the proposed method has twice the measurement range of the conventional model. In order to verify the proposed CCM measurement model, a laboratory thickness measurement system was developed by the authors' team. A commercial laser scanning confocal microscope (Carl Zeiss LSM780) was used as the reference system. A set of quartz glasses was measured using both the proposed system and the reference system. Experimental comparison showed that the proposed method was able to achieve a measurement accuracy of 0.25 µm. In addition, repeated measurements conducted at different heights showed negligible variation. Thus, it can be concluded that the specimen placement tolerance was improved significantly compared with the conventional model.
RESUMEN
Dicing is a critical step in the manufacturing process for the application of sapphire. In this work, the dependence of sapphire dicing on crystal orientation using picosecond Bessel laser beam drilling combined with mechanical cleavage was studied. By using the above method, linear cleaving with on debris and zero tapers was realized for the A1, A2, C1, C2, and M1 orientations, except for the M2 orientation. The experimental results indicated that characteristics of Bessel beam-drilled microholes, fracture loads, and fracture sections of sapphire sheets were strongly dependent on crystal orientation. No cracks were generated around the micro holes when laser scanned along the A2 and M2 orientations, and the corresponding average fracture loads were large, 12.18 N and 13.57 N, respectively. While along the A1, C1, C2, and M1 orientations, laser-induced cracks extended along the laser scanning direction, resulting in a significant reduction in fracture load. Furthermore, the fracture surfaces were relatively uniform for A1, C1, and C2 orientations but uneven for A2 and M1 orientations, with a surface roughness of about 1120 nm. In addition, curvilinear dicing without debris or taper was achieved to demonstrate the feasibility of Bessel beams.
RESUMEN
Wide-bandgap (WBG) perovskite solar cells suffer from severe non-radiative recombination and exhibit relatively large open-circuit voltage (VOC) deficits, limiting their photovoltaic performance. Here, we address these issues by in-situ forming a well-defined 2D perovskite (PMA)2PbCl4 (phenmethylammonium is referred to as PMA) passivation layer on top of the WBG active layer. The 2D layer with highly pure dimensionality and halide components is realized by intentionally tailoring the side-chain substituent at the aryl ring of the post-treatment reagent. First-principle calculation and single-crystal X-ray diffraction results reveal that weak intermolecular interactions between bulky PMA cations and relatively low cation-halide hydrogen bonding strength are crucial in forming the well-defined 2D phase. The (PMA)2PbCl4 forms improved type-I energy level alignment with the WBG perovskite, reducing the electron recombination at the perovskite/hole-transport-layer interface. Applying this strategy in fabricating semi-transparent WBG perovskite solar cells (indium tin oxide as the back electrode), the VOC deficits can be reduced to 0.49 V, comparable with the reported state-of-the-art WBG perovskite solar cells using metal electrodes. Consequently, we obtain hysteresis-free 18.60%-efficient WBG perovskite solar cells with a high VOC of 1.23 V.
RESUMEN
A non-resonant piezoelectric linear motor with alternating normal contact force is developed to realize a piezoelectric linear motor with high precision, large stroke, and strong thrust. The motor employs four piezoelectric stacks to excite the non-resonant state vibration of two driving feet, which alternately push the mover to generate unidirectional motion. Through the analysis of the working principle of the motor, the structure of the motor is designed and manufactured. The test results show the feasibility of the motor. Furthermore, the operating results show that the flatness of the contact surface strongly affects the performance of the motor. The design criteria of the motor are proposed, thus providing a basis for the optimization of the motor.
RESUMEN
In order to aid imaging physicians to effectively screen chest radiography medical images for presence of Coronavirus Disease 2019 (COVID-19), a novel computer aided diagnosis technology for automatic processing of COVID-19 images is proposed based on two-dimensional variational mode decomposition (2D-VMD) and locally linear embedding (LLE). 2D-VMD algorithm is used to decompose normal and COVID-19 images, and then feature extraction of intrinsic mode functions (IMFs) using Gabor filter. To better extract low-dimensional parameters which are useful for COVID-19 diagnosis, the performance of two dimensionality reduction techniques of principal component analysis (PCA) and LLE are compared, and the LLE is shown to offer satisfactory effect of dimension reduction. Thereafter, the particle swarm optimization-support vector machine (PSO-SVM) algorithm is used to classify. The simulation results show that the proposed technology has achieved accuracy of 99.33%, precision of 100%, recall of 98.63% and F-Measure of 99.31%. Hence, the developed diagnosis technology can be used as an important auxiliary tool to assist diagnosis of imaging physicians.