Surfactant-assisted synthesis of polythiophene/Ni0.5Zn0.5Fe2-xCexO4 ferrite composites: study of structural, dielectric and magnetic properties for EMI-shielding applications.

This work reports the exploitation of nanocrystalline Ni0.5Zn0.5Fe2-xCexO4 ferrite for potential application by designing quasi-spherical shaped polythiophene (PTH) composites via in situ emulsion polymerization. The structural, electronic, dielectric, magnetic, and electromagnetic interference (EMI) shielding properties of PTH/Ni0.5Zn0.5Fe2-xCexO4 composites were investigated. Our results suggest that these properties could be optimized by modulating the concentration of x (composition) in the polymer matrix. Higher values of ε' and ε'' were obtained on composite formation, and could be due to the heterogeneity developed in the material. An enhancement in the value of saturation magnetization (123 emu g-1 for x = 0.04) and Curie temperature was obtained with Ce concentration, which is useful for high density recording purposes. A low value of saturation magnetization was obtained for the PTH/Ni0.5Zn0.5Fe2-xCexO4 composite (36 emu g-1 for x = 0.04). This could be attributed to the non-magnetic nature of the polymer. A total shielding effectiveness (SET = SEA + SER) up to 34 dB (≈99.9% attenuation) was recorded for PTH/Ni0.5Zn0.5Fe2-xCexO4 composites (x = 0.04) in a frequency range of 8.2-12.4 GHz (X-band), which surpasses the shielding criteria of SET > 30 dB for commercial purposes. Such a material with high SE identifies its potential for making electromagnetic shields. The effect of Ce substitution on the microstructure, dielectric, impedance and magnetic properties of PTH/Ni0.5Zn0.5Fe2-xCexO4 ferrite composites was also investigated. X-ray diffraction analysis confirmed cubic spinel phase formation, and the broad reflection peaks indicated the formation of smaller sized particles. The smaller energy band gap (2.53 eV) of the composite indicated that this material could be used for photocatalysis in the visible region. Dielectric and impedance measurements were carried out in a frequency range of 8.2-12.4 GHz. Dielectric properties were improved considerably by the substitution of Ce3+ ions in PTH/Ni0.5Zn0.5Fe2-xCexO4 composites. Impedance spectroscopy was used to study the effect of grain and grain boundaries on the electrical properties of PTH/Ni0.5Zn0.5Fe2-xCexO4 composites. Cole-Cole plots showed the formation of single semi-circles for all samples in the measured frequency range. This showed that the composite material was composed of good conducting grains and poorly conducting grain boundaries.

Barium ferrite decorated reduced graphene oxide nanocomposite for effective electromagnetic interference shielding.

There is an increased interest in the development of high performance microwave shielding materials against electromagnetic pollution in recent years. Barium ferrite decorated reduced graphene oxide (BaFe12O19@RGO) nanocomposite was synthesized by a high energy ball milling technique and its electromagnetic properties were investigated in the frequency range of 12.4-18 GHz (Ku band). The results showed that barium ferrite (BaFe12O19) nanoparticles with an average particle size of 20-30 nm were well distributed and firmly anchored onto the surface of the reduced graphene oxide sheets. The obtained nanocomposite exhibited a saturation magnetization of 18.1 emu g(-1) at room temperature. The presence of BaFe12O19 nanoparticles in the nanocomposite enhances the space charge polarization, natural resonance, multiple scattering and the effective anisotropy energy leading to a high electromagnetic interference shielding effectiveness of 32 dB (∼99.9% attenuation) at a critical thickness of 3 mm. The results suggested that the as-prepared BaFe12O19@RGO nanocomposite showed great potential as an effective candidate for a new type of microwave absorbing material.

Mass scale synthesis of graphene nanosheets using waste cardboard for application in perovskite solar cells and supercapacitors.

Advanced graphene-based materials have been proficiently incorporated into next-generation solar cells and supercapacitors because of their high electrical conductivity, large surface area, excellent charge-transport ability, and exceptional optical properties. Herein, we report the synthesis of graphene nanosheets (GNs) from waste cardboard via pyrolysis, with ethyl alcohol as the growth initiator. Additionally, we demonstrated the use of GNs in energy conversion and storage applications. Using the GN electrode in perovskite solar cells resulted in an excellent power conversion efficiency of ∼10.41 % for an active area of 1 cm2, indicating an enhancement of approximately 27 % compared to conventional electrodes. Furthermore, the GNs were used as active electrode materials in supercapacitors with excellent electrochemical performance and a high gravimetric specific capacitance of 167.5 F/g at a scan rate of 2 mV/s. The developed GNs can be efficiently used for energy storage, conversion, and electrochemical sensing applications.

Graphene oxide/ferrofluid/cement composites for electromagnetic interference shielding application.

This paper deals with the preparation of graphene oxide-ferrofluid-cement nanocomposites to evaluate the electromagnetic interference (EMI) shielding effectiveness (SE) in the 8.2-12.4 GHz frequency range. It has been observed that incorporation of graphene oxide (30 wt%) along with an appropriate amount of ferrofluid in the cement matrix leads to a shielding effectiveness of 46 dB (>99% attenuation).The presence of graphene oxide and ferrofluid in the cement leads to strong polarizations and magnetic losses that consequently result in higher shielding effectiveness compared to pristine cement. The resulting nanocomposites have shown Shore hardness of 54 and dc conductivity of 10.40 S cm( - 1). SEM reveals the homogeneous dispersion of graphene oxide and ferrofluid in the cement matrix.

Lightweight and Easily Foldable MCMB-MWCNTs Composite Paper with Exceptional Electromagnetic Interference Shielding.

Lightweight and easily foldable with high conductivity, multiwalled carbon nanotube (MWCNT)-based mesocarbon microbead (MCMB) composite paper is prepared using a simple, efficient, and cost-effective strategy. The developed lightweight and conductive composite paper have been reported for the first time as an efficient electromagnetic interference (EMI) shielding material in X-band frequency region having a low density of 0.26 g/cm(3). The investigation revealed that composite paper shows an excellent absorption dominated EMI shielding effectiveness (SE) of -31 to -56 dB at 0.15-0.6 mm thickness, respectively. Specific EMI-SE of as high as -215 dB cm(3)/g exceeds the best values of metal and other low-density carbon-based composites. Additionally, lightweight and easily foldable ability of this composite paper will help in providing stable EMI shielding values even after constant bending. Such intriguing performances open the framework to designing a lightweight and easily foldable composite paper as promising EMI shielding material, especially in next-generation devices and for defense industries.

Soluble substituted poly-p-phenylenes--a new material for application in light-emitting diodes: synthesis and characterization.

Poly-p-phenylenes have attracted a great deal of attention with respect to their applications in displays, light-emitting devices, and batteries. However, the polymer poly-p-phenylene obtained by the Kovacic method is insoluble and intractable. The present study reports the preparation of soluble poly(p-phenylenes) by polymerization of derivatives of benzene in the presence of a specific aromatic nuclei. The resultant copolymer so obtained is soluble in common organic solvents such as chloroform and toluene. Preliminary studies have indicated that the polymer shows orange photoluminescence and electroluminescence when a potential of 7-10 V is applied to the device.

Nanostructured graphene/Fe3O4 incorporated polyaniline as a high performance shield against electromagnetic pollution.

The development of high-performance shielding materials against electromagnetic pollution requires mobile charge carriers and magnetic dipoles. Herein, we meet the challenge by building a three-dimensional (3D) nanostructure consisting of chemically modified graphene/Fe3O4(GF) incorporated polyaniline. Intercalated GF was synthesized by the in situ generation of Fe3O4 nanoparticles in a graphene oxide suspension followed by hydrazine reduction, and further in situ polymerization with aniline to form a polyaniline composite. Spectroscopic analysis demonstrates that the presence of GF hybrid structures facilitates strong polarization due to the formation of a solid-state charge-transfer complex between graphene and polyaniline. This provides proper impedance matching and higher dipole interaction, which leads to the high microwave absorption properties. The higher dielectric loss (ε'' = 30) and magnetic loss (µ'' = 0.2) contribute to the microwave absorption value of 26 dB (>99.7% attenuation), which was found to depend on the concentration of GF in the polyaniline matrix. Moreover, the interactions between Fe3O4, graphene and polyaniline are responsible for superior material characteristics, such as excellent environmental (chemical and thermal) degradation stability and good electric conductivity (as high as 260 S m(-1)).

Search for Lorentz and CPT violation effects in Muon spin precession.

The spin precession frequency of muons stored in the (g-2) storage ring has been analyzed for evidence of Lorentz and CPT violation. Two Lorentz and CPT violation signatures were searched for a nonzero delta omega a(=omega a mu+ - omega a mu-) and a sidereal variation of omega a mu+/-). No significant effect is found, and the following limits on the standard-model extension parameters are obtained: bZ = -(1.0+/-1.1) x 10(-23) GeV; (m mu dZ0 + HXY)=(1.8+/-6.0) x 10(-23) GeV; and the 95% confidence level limits b perpendicular mu+ <1.4 x 10(-24) GeV and b perpendicular mu- <2.6 x 10(-24) GeV.

Measurement of the negative muon anomalous magnetic moment to 0.7 ppm.

The anomalous magnetic moment of the negative muon has been measured to a precision of 0.7 ppm (ppm) at the Brookhaven Alternating Gradient Synchrotron. This result is based on data collected in 2001, and is over an order of magnitude more precise than the previous measurement for the negative muon. The result a(mu(-))=11 659 214(8)(3) x 10(-10) (0.7 ppm), where the first uncertainty is statistical and the second is systematic, is consistent with previous measurements of the anomaly for the positive and the negative muon. The average of the measurements of the muon anomaly is a(mu)(exp)=11 659 208(6) x 10(-10) (0.5 ppm).

Precise measurement of the positive muon anomalous magnetic moment.

A precise measurement of the anomalous g value, a(mu) = (g-2)/2, for the positive muon has been made at the Brookhaven Alternating Gradient Synchrotron. The result a(mu+) = 11 659 202(14) (6) x 10(-10) (1.3 ppm) is in good agreement with previous measurements and has an error one third that of the combined previous data. The current theoretical value from the standard model is a(mu)(SM) = 11 659 159.6(6.7) x 10(-10) (0.57 ppm) and a(mu)(exp) - a(mu)(SM) = 43(16) x 10(-10) in which a(mu)(exp) is the world average experimental value.

Measurement of the positive muon anomalous magnetic moment to 0.7 ppm.

A higher precision measurement of the anomalous g value, a(mu)=(g-2)/2, for the positive muon has been made at the Brookhaven Alternating Gradient Synchrotron, based on data collected in the year 2000. The result a(mu(+))=11 659 204(7)(5)x10(-10) (0.7 ppm) is in good agreement with previous measurements and has an error about one-half that of the combined previous data. The present world average experimental value is a(mu)(expt)=11 659 203(8)x10(-10) (0.7 ppm).