Exploring the Use of Cold Atmospheric Plasma for Sound and Vibration Generation.

In this study, we investigate the potential of cold atmospheric plasma (CAP) as a non-contact excitation device, comparing its performance with an ultrasound transmitter. Utilizing a scanning Laser Doppler Vibrometer (LDV), we visualize the acoustic wavefront generated by a CAP probe and an ultrasound sensor within a designated 50 mm × 50 mm area in front of each probe. Our focus lies in assessing the applicability of a CAP probe for exciting a small polymethyl methacrylate (PMMA) sample. By adjusting the dimensions of the sample to resonate at the excitation frequency of the probe, we can achieve high vibrational velocities, enabling further mechanical analysis. In contrast with traditional vibration excitation techniques such as electrodynamical shakers and hammer impact excitation, a plasma probe can offer distinct advantages without altering the structure's dynamics since it is contactless. Furthermore, in comparison with laser excitation, plasma excitation provides a higher power level. Additionally, while pressurized air systems are applicable for limited low frequencies, plasma probes can perform at higher frequencies. Our findings in this study suggest that CAP is comparable with acoustic excitation, indicating its potential as an effective mechanical excitation method.

Blowing pressure stabilization method for the artificial excitation of reed instruments (L).

To investigate the acoustics of reed instruments without the need for a human player, blowing machines are needed, which can generate air pressures up to 8 kPa and flow rates up to 40 liters per minute. Due to reed flexibility and the changing pressure gradient across the reed, the relationship between flow and pressure is highly non-linear. Since the output pressure of ventilators is highly dependent on flow, non-linear pressure regulation is a difficult task that requires a closed-loop approach. Since reed vibration starts suddenly when blowing pressure is gradually increased, an abrupt change in airflow through the instrument is present, resulting in a change in pressure in the artificial mouth. To avoid that, a method is presented to achieve a fast response to abrupt flow changes, which is tested in an existing blowing machine. The enhanced blowing machine exhibits a settling time below 200 ms, which allows for the generation of blowing pressures with linear responses.

Material Identification on Thin Shells Using the Virtual Fields Method, Demonstrated on the Human Eardrum.

Characterization of material parameters from experimental data remains challenging, especially on biological structures. One of such techniques allowing for the inverse determination of material parameters from measurement data is the virtual fields method (VFM). However, application of the VFM on general structures of complicated shape has not yet been extensively investigated. In this paper, we extend the framework of the VFM method to thin curved solids in three-dimensional, commonly denoted shells. Our method is then used to estimate the Young's modulus and hysteretic damping of the human eardrum. By utilizing Kirchhoff plate theory, we assume that the behavior of the shell varies linearly through the thickness. The total strain of the shell can then be separated in a bending and membrane strain. This in turn allowed for an application of the VFM based only on data of the outer surface of the shell. We validated our method on simulated and experimental data of a human eardrum made to vibrate at certain frequencies. It was shown that the identified material properties were accurately determined based only on data from the outer surface and are in agreement with literature. Additionally, we observed that neither the bending nor the membrane strain in an human eardrum can be neglected and both contribute significantly to the total strain found experimentally.

Synchrotron radiation X-ray microtomography for the visualization of intra-cochlear anatomy in human temporal bones implanted with a perimodiolar cochlear implant electrode array.

Recently, synchrotron radiation computed microtomography (SRµCT) has emerged as a promising tool for non-destructive, in situ visualization of cochlear implant electrode arrays inserted into a human cochlea. Histological techniques have been the `gold standard' technique for accurate localization of cochlear implant electrodes but are suboptimal for precise three-dimensional measurements. Here, an SRµCT experimental setup is proposed that offers the benefit of a high spatial and contrast resolution (isotropic voxel size = 4.95 µm and propagation-based phase-contrast imaging), while visualizing the soft-tissue structures and electrode array of the cochlear implant simultaneously. In this work, perimodiolar electrode arrays have been tested, which incorporate thick and closely spaced platinum-iridium contacts and wiring. These data can assist cochlear implant and hearing research, can be used to verify electrode segmentation techniques for clinical computed tomography or could be utilized to evaluate cochlear implant electrode array designs.

Three-dimensional vibration patterns of alto saxophone reeds measured on different mouthpieces under mimicked realistic playing conditions.

In single reed musical instruments, vibrations of the reed, in conjunction with the geometry of the mouthpiece and the acoustic feedback of the instrument, play an essential role in sound generation. Up until now, three-dimensional (3D) reed vibration patterns have only been studied under external acoustic stimulation, or at a single note and lip force. This paper investigates vibration patterns of saxophone reeds under imitated realistic playing conditions. On different notes displacement measurements on the entire optically accessible part of the reed are performed using stroboscopic digital image correlation. These vibration data are decomposed onto the harmonic frequencies of the generated note pitch and into the operational modes. Motion data as a function of time are shown on single points. All points on the reed predominantly move in phase, corresponding to the first flexural mode of the reed. At higher note harmonics very low amplitude higher vibration modes are superimposed on the fundamental mode. Mouthpiece characteristics and lip force influence the vibration patterns. Vibration patterns differ strongly from earlier measurements on free vibrating reeds. Results show that single-point measurements on the tip of the reed can give a good indication of the 3D vibration amplitude, also at higher note pitches.

Deep neural networks for single shot structured light profilometry.

In 3D optical metrology, single-shot structured light profilometry techniques have inherent advantages over their multi-shot counterparts in terms of measurement speed, optical setup simplicity, and robustness to motion artifacts. In this paper, we present a new approach to extract height information from single deformed fringe patterns, based entirely on deep learning. By training a fully convolutional neural network on a large set of simulated height maps with corresponding deformed fringe patterns, we demonstrate the ability of the network to obtain full-field height information from previously unseen fringe patterns with high accuracy. As an added benefit, intermediate data processing steps such as background masking, noise reduction and phase unwrapping that are otherwise required in classic demodulation strategies, can be learned directly by the network as part of its mapping function.

Effect of Local Neck Anatomy on Localized One-Dimensional Measurements of Arterial Stiffness: A Finite-Element Model Study.

Cardiovascular diseases (CVD) are the most prevalent cause of death in the Western World, and their prevalence is only expected to rise. Several screening modalities aim at detecting CVD at the early stages. A common target for early screening is common carotid artery (CCA) stiffness, as reflected in the pulse wave velocity (PWV). For assessing the CCA stiffness using ultrasound (US), one-dimensional (1D) measurements along the CCA axis are typically used, ignoring possible boundary conditions of neck anatomy and the US probe itself. In this study, the effect of stresses and deformations induced by the US probe, and the effect of anatomy surrounding CCA on a simulated 1D stiffness measurement (PWVus) is compared with the ground truth stiffness (PWVgt) in 60 finite-element models (FEM) derived from anatomical computed tomography (CT) scans of ten healthy male volunteers. Based on prior knowledge from the literature, and from results in this study, we conclude that it is safe to approximate arterial stiffness using 1D measurements of compliance or pulse wave velocity, regardless of boundary conditions emerging from the anatomy or from the measurement procedure.

Structural intensity assessment on shells via a finite element approximation.

Structural intensity on plates or shells can provide insights on how the vibrational energy is transmitted throughout a sample. Its assessment via experimental deflections are widely documented in the case of plates, which just requires the computation of spatial derivatives of out-of-plane displacements or velocities and a knowledge of the sample's material properties. However, if the structural intensity is to be assessed on arbitrary shells, a more elaborate data processing is required. The in-plane displacements become relevant terms and the spatial derivatives along a predefined local coordinate system need to be computed. Here, a method from which experimental data is interpolated on a finite element mesh is proposed. First, the global displacements and shape of a sample's outer-surface are measured. These data are then projected on a quadratic mesh, where the Kirchhoff plate theory is invoked for the individual elements. The data differentiation is computed via quadratic shape functions, from which the strains and structural intensity are estimated. Through the obtained vibrational energy results on the basis of measured displacement and shape data and by validating the method via a numerical simulation, the proposed work has shown to be a reliable tool to assess energy transmission on irregular shells.

The effect of craniokinesis on the middle ear of domestic chickens (Gallus gallus domesticus).

The avian middle ear differs from that of mammalians and contains a tympanic membrane, one ossicle (bony columella and cartilaginous extra-columella), some ligaments and one muscle. The rim of the eardrum (closing the middle ear cavity) is connected to the neurocranium and, by means of a broad ligament, to the otic process of the quadrate. Due to the limited number of components in the avian middle ear, the possibilities of attenuating the conduction of sound seem to be limited to activity of the stapedius muscle. We investigate to what extent craniokinesis may impact the components of the middle ear because of the connection of the eardrum to the movable quadrate. The quadrate is a part of the beak suspension and plays an important role in craniokinesis. Micro-computed tomography was used to visualize morphology and the effect of craniokinesis on the middle ear in the domestic chicken (Gallus gallus domesticus). Both hens and roosters are considered because of their difference in vocalization capacity. It is hypothesized that effects, if present, of craniokinesis on the middle ear will be greater in roosters because of their louder vocalization. Maximal lower jaw depression was comparable for hens and roosters (respectively 34.1 ± 2.6° and 32.7 ± 2.5°). There is no overlap in ranges of maximal upper jaw elevation between the sexes (respectively 12.7 ± 2.5° and 18.5 ± 3.8°). Frontal rotation about the transversal quadrato-squamosal, and inward rotation about the squamosal-mandibular axes of the quadrate were both considered to be greater in roosters (respectively 15.4 ± 2.8° and 11.1 ± 2.5°). These quadrate rotations did not affect the columellar position or orientation. In hens, an influence of the quadrate movements on the shape of the eardrum could not be detected either; however, craniokinesis caused slight stretching of the eardrum towards the caudal rim of the otic process of the quadrate. In roosters, an inward displacement of the conical tip of the tympanic membrane of 0.378 ± 0.21 mm, as a result of craniokinesis, was observed. This is linked to a flattening and slackening of the eardrum. These changes most likely go along with a deformation of the extra-columella. Generally, in birds, larger beak opening is related to the intensity of vocalization. The coupling between larger maximal upper jaw lifting in roosters and the slackening of the eardrum suggest the presence of a passive sound attenuation mechanism during self-vocalization.

Jaw morphology and fighting forces in stag beetles.

The jaws of different species of stag beetles show a large variety of shapes and sizes. The male jaws are used as weapons in fights, and they may exert a very forceful bite in some species. We investigated in 16 species whether and how the forcefulness of their bite is reflected in their jaw morphology. We found a large range of maximal muscle forces (1.8-33 N; factor of 18). Species investing in large bite muscles also have disproportionately large jaw volumes. They use this additional jaw volume to elongate their jaws, increasing their chances of winning in battles. The fact that this also decreases the mechanical advantage is largely compensated for by elongated in-levers. As a result, high muscle forces are correlated with elevated bite forces (0.27-7.6 N; factor of 28). Despite the large difference in the forcefulness of their bite, all investigated species experience similar Von Mises stresses in their jaws while biting (29-114 MPa; factor of 4.0; calculated with finite element simulations). Hence, stag beetles have successfully adapted their jaw anatomy according to their bite force in fights.

Phase shifting and phase retrieval with a fully automated laser diode system.

A low-cost and fully automated process for phase-shifting interferometry (PSI) by continuously changing the input voltage of a laser diode (LD) under the scheme of an unbalanced Twyman-Green interferometer (TGI) setup is presented. The input signal of a LD is controlled by a data acquisition (NI-DAQ) device that allows it to change its wavelength according to its tunability features. The automation and data analysis will be done using LabVIEW in combination with MATLAB. The phase map is obtained using the Carré algorithm. Measurements of visibility and phase shift to verify the PSI requirements are shown. It is demonstrated with experimental results and statistical analysis that the phase retrieval can be successfully achieved without calibration and using minimal optical devices.

Fully automated low-cost setup for fringe projection profilometry.

In this paper an alternative low-cost, easy-to-use, and fully automated profilometry setup is proposed. The setup is based on a phase-shifting fringe projection technique with four projected fringe parameters. It uses the well-known triangulation arrangement and low-cost electronic and image acquisition components such as a data acquisition board, a motor controller board, a printer rail, a CMOS webcam, and an LCD projector. The position of the camera, the generation of the fringe pattern, the acquisition of the images, and the calculation of the wrapped and unwrapped phase are all performed in LabVIEW. The setup is portable and can be perfectly adapted to be used in other profilometry techniques such as electronic speckle pattern interferometry and laser scanning profilometry.

Real-time microscopic phase-shifting profilometry.

A real-time microscopic profilometry system based on digital fringe projection and parallel programming has been developed and experimentally tested. Structured light patterns are projected onto an object through one pathway of a stereoscopic operation microscope. The patterns are deformed by the shape of the object and are then recorded with a high-speed CCD camera placed in the other pathway of the microscope. As the optical pathways of both arms are separated and reach the same object point at a relative angle, the recorded patterns allow the full-field object height variations to be calculated and the three-dimensional shape to be reconstructed by employing standard triangulation techniques. Applying proper hardware triggering, the projector-camera system is synchronized to capture up to 120 unique deformed line patterns per second. Using standard four-step phase-shifting profilometry techniques and applying graphics processing unit programming for fast phase wrapping, scaling, and visualization, we demonstrate the capability of the proposed system to generate 30 microscopic height maps per second. This allows the qualitative depth perception of the stereomicroscope operator to be enhanced by live quantitative height measurements with depth resolutions in the micrometer range.

MicroFilament Analyzer, an image analysis tool for quantifying fibrillar orientation, reveals changes in microtubule organization during gravitropism.

Image acquisition is an important step in the study of cytoskeleton organization. As visual interpretations and manual measurements of digital images are prone to errors and require a great amount of time, a freely available software package named MicroFilament Analyzer (MFA) was developed. The goal was to provide a tool that facilitates high-throughput analysis to determine the orientation of filamentous structures on digital images in a more standardized, objective and repeatable way. Here, the rationale and applicability of the program is demonstrated by analyzing the microtubule patterns in epidermal cells of control and gravi-stimulated Arabidopsis thaliana roots. Differential expansion of cells on either side of the root results in downward bending of the root tip. As cell expansion depends on the properties of the cell wall, this may imply a differential orientation of cellulose microfibrils. As cellulose deposition is orchestrated by cortical microtubules, the microtubule patterns were analyzed. The MFA program detects the filamentous structures on the image and identifies the main orientation(s) within individual cells. This revealed four distinguishable microtubule patterns in root epidermal cells. The analysis indicated that gravitropic stimulation and developmental age are both significant factors that determine microtubule orientation. Moreover, the data show that an altered microtubule pattern does not precede differential expansion. Other possible applications are also illustrated, including field emission scanning electron micrographs of cellulose microfibrils in plant cell walls and images of fluorescent actin.

Biomechanical determinants of bite force dimorphism in Cyclommatus metallifer stag beetles.

In the stag beetle family (Lucanidae), males have diverged from females by sexual selection. The males fight each other for mating opportunities with their enlarged mandibles. It is known that owners of larger fighting apparatuses are favoured to win the male-male fights, but it was unclear whether male stag beetles also need to produce high bite forces while grabbing and lifting opponents in fights. We show that male Cyclommatus metallifer stag beetles bite three times as forcefully as females. This is not entirely unexpected given the spectacular nature of the fights, but all the more impressive given the difficulty of achieving this with their long mandibles (long levers). Our results suggest no increase in male intrinsic muscle strength to accomplish this. However, morphological analyses show that the long mandibular output levers in males are compensated by elongated input levers (and thus a wider anterior side of the head). The surplus of male bite force capability is realized by enlargement of the closer muscles of the mandibles, while overall muscle force direction remained optimal. To enable the forceful bites required to ensure male reproductive success, male head size and shape are adapted for long input levers and large muscles. Therefore, the entire head should be regarded as an integral part of male armature.

Volume shrinkage of bone, brain and muscle tissue in sample preparation for micro-CT and light sheet fluorescence microscopy (LSFM).

Two methods are especially suited for tomographic imaging with histological detail of macroscopic samples that consist of multiple tissue types (bone, muscle, nerve or fat): Light sheet (based) fluorescence microscopy (LSFM) and micro-computed tomography (micro-CT). Micro-CT requires staining with heavy chemical elements (and thus fixation and sometimes dehydration) in order to make soft tissue imageable when measured alongside denser structures. LSMF requires fixation, decalcification, dehydration, clearing and staining with a fluorescent dye. The specimen preparation of both imaging methods is prone to shrinkage, which is often not mentioned, let alone quantified. In this paper the presence and degree of shrinkage are quantitatively identified for the selected preparation methods/stains. LSFM delivers a volume shrinkage of 17% for bone, 56% for muscle and 62% for brain tissue. The three most popular micro-CT stains (phosphotungstic acid, iodine with potassium iodide, and iodine in absolute ethanol) deliver a volume shrinkage ranging from 10 to 56% for muscle and 27-66% for brain, while bone does not shrink in micro-CT preparation.

The importance of mechanical and biological cues of tympanic membrane grafts to ensure optimal regeneration.

Chronic suppurative otitis media (CSOM) is often associated with permanent tympanic membrane (TM) perforation and conductive hearing loss. The current clinical gold standard, using autografts and allografts, suffers from several drawbacks. Artificial replacement materials can help to overcome these drawbacks. Therefore, scaffolds fabricated through digital light processing (DLP) were herein created to support TM regeneration. Various UV-curable printing inks, including gelatin methacryloyl (GelMA), gelatin-norbornene-norbornene (GelNBNB) (crosslinked with thiolated gelatin (GelSH)) and alkene-functionalized poly-ε-caprolactone (E-PCL) (crosslinked with pentaerythritol tetrakis(3-mercaptopropionate) (PETA4SH)) were optimized regarding photo-initiator (PI) and photo-absorber (PA) concentrations through viscosity characterization, photo-rheology and the establishment of working curves for DLP. Our material platform enabled the development of constructs with a range of mechanical properties (plateau storage modulus varying between 15 and 119 kPa). Excellent network connectivity for the GelNBNB and E-PCL constructs was demonstrated (gel fractions >95 %) whereas a post-crosslinking step was required for the GelMA constructs. All samples showed excellent biocompatibility (viability >93 % and metabolic activity >88 %). Finally, in vivo and ex vivo assessments, including histology, vibration and deformation responses measured through laser doppler vibrometry and digital image correlation respectively, were performed to investigate the effects of the scaffolds on the anatomical and physiological regeneration of acute TM perforations in rabbits. The data showed that the most efficient healing with the best functional quality was obtained when both mechanical (obtained with the PCL-based resin) and biological (obtained with the gelatin-based resins) material properties were taken into account.

Alexithymia and empathy predict changes in autonomic arousal during affective stimulation.

BACKGROUND: Alexithymia, the inability to describe one's own emotions, is linked to deficits in empathy, manifesting as a diminished capacity to recognize or understand the emotions and mental states of others. Several brain centers of autonomic control and interoception that are activated in empathy are thought to misfunction in alexithymia. We hypothesized that individual differences in autonomic changes under affective stimulation might be associated with differences in alexithymia and empathy. METHODS: We studied 21 healthy volunteers, comparing their alexithymia and empathy scores with changes in their sympathetic autonomic arousal, indexed by the palmar skin potential level, during 3 tasks: playing a computer game, performing mental arithmetic, and watching a negative emotional valence video. RESULTS: Both autonomic and subjective sense of arousal increased at the beginning of each task and then gradually subsided over the course of the task. Higher autonomic arousal at the onset of the computer game was associated with higher empathy scores, and at the onset of the negative video with higher scores for both empathy and alexithymia. Alexithymia delayed the habituation of autonomic arousal during the computer game, while the empathy score was related to a faster decline in arousal during the negative video task. CONCLUSIONS: High alexithymia and high empathy scores were linked to increased autonomic arousal at the onset of emotional stimulation, but were distinguishable in the rates of habituation of the evoked arousal. Our data provide insight into the relationships among interacting psychological traits, physiologic regulation, and the arousal dimension of emotional experience.

Prestrain in the eardrum investigated using laser-ablation perforation: A proof of principle study on the New Zealand white rabbit.

While the presence of residual stress (also called prestress) in the tympanic membrane (TM) was hypothesized more than 150 years ago by von Helmholtz (1869), little experimental data exists to date. In this paper, a novel approach to study residual stress is presented. Using a pulsed laser, the New Zealand white rabbit TM is perforated at seven predefined locations. The subsequent retraction of the membrane around the holes is computed using digital image correlation (DIC). The amount of retraction is the so-called prestrain, which is caused by the release of prestress due to the perforation. By measuring the prestrain using DIC, we show that residual stress is clearly present over the entire rabbit TM surface. In total, fourteen TMs have been measured in this work. An automated approach allows tracking the holes' deformation during the measurement process and enables a more robust analysis than was previously possible. We find similar strains (around 5%) as reported in previous work, in which slits were created manually using flattened surgical needles. However, the new approach greatly reduces measurement time, which minimizes dehydration artifacts. To investigate the effect of perforation location on the TM, the spatial decrease of the prestrain (α) around the perforation was quantified. Perforations inferior to the umbo showed the least negative α values, i.e., the most gradual decrease around the hole, and were the most consistent. Perforations on other locations showed more negative α values, i.e., steeper decrease in strain, but were less consistent across samples. We also investigated the effect of the holes' creation sequence but did not observe a significant change in the results. Overall, the presented method allows for consistent residual stress measurements over the TM surface. The findings contribute to our fundamental knowledge of the mechanics of the rabbit TM and provide a basis for future work on human TMs.

Rabbit tympanic membrane thickness distribution obtained via optical coherence tomography.

Knowing the precise tympanic membrane (TM) thickness variation is crucial in understanding the functional properties of the TM and has a significant effect on the accuracy of computational models. Using optical coherence tomography, we imaged five left and five right TMs of domestic New Zealand rabbits. From these data, ten thickness distribution maps were computed. Although inter-specimen variability is present, similar features could be observed in all samples: The rabbit TM is thickest around the umbo, with values of 150 ± 32 µm. From the umbo towards the TM annulus, the thickness gradually decreases down to 38 ± 7 µm around the midway location, but increases up to 54 ± 19 µm at the TM annulus. The thickness values at the umbo are comparable to literature data for humans, but the rabbit TM is thinner at the TM annulus and in-between the umbo and annulus. Moreover, the rabbit TM thickness distribution is highly symmetrical, which is not the case for the human TM. The results improve our general understanding of TM structure in rabbits and may improve numerical models of TM dynamical behavior.