Self-supported Pt-CoO networks combining high specific activity with high surface area for oxygen reduction.

Several concepts for platinum-based catalysts for the oxygen reduction reaction (ORR) are presented that exceed the US Department of Energy targets for Pt-related ORR mass activity. Most concepts achieve their high ORR activity by increasing the Pt specific activity at the expense of a lower electrochemically active surface area (ECSA). In the potential region controlled by kinetics, such a lower ECSA is counterbalanced by the high specific activity. At higher overpotentials, however, which are often applied in real systems, a low ECSA leads to limitations in the reaction rate not by kinetics, but by mass transport. Here we report on self-supported platinum-cobalt oxide networks that combine a high specific activity with a high ECSA. The high ECSA is achieved by a platinum-cobalt oxide bone nanostructure that exhibits unprecedentedly high mass activity for self-supported ORR catalysts. This concept promises a stable fuel-cell operation at high temperature, high current density and low humidification.

Electrolyte Effects on the Electrocatalytic Performance of Iridium-Based Nanoparticles for Oxygen Evolution in Rotating Disc Electrodes.

Proton exchange membrane water electrolysers are very promising renewable energy conversion devices that produce hydrogen from sustainable feedstocks. These devices are mainly limited by the sluggish kinetics of the oxygen evolution reaction (OER). Ir-based nanoparticles are both reasonably active and stable for the OER in acidic media. The electrolyte composition and the pH may play a crucial role in electrocatalysis, yet they have been widely overlooked for the OER. Herein, we present a study on the effects of the composition and concentration of the electrolyte on commercial Ir black nanoparticles using concentrations of 0.05 M, 0.1 M and 0.5 M of both sulphuric and perchloric acid. The results show an important effect of the electrolyte composition on the catalytic performance of the Ir nanoparticles. The concentration of H2 SO4 interferes on the oxidation of Ir and decreases the catalytic performance of the catalyst. HClO4 does not show strong interferences in the electrochemistry of Ir. Higher catalytic performances are observed in HClO4 electrolytes in comparison to H2 SO4 with little effect of the concentration of HClO4 .

Ab Initio Cyclic Voltammetry on Cu(111), Cu(100) and Cu(110) in Acidic, Neutral and Alkaline Solutions.

Electrochemical reactions depend on the electrochemical interface between the electrode surfaces and the electrolytes. To control and advance electrochemical reactions there is a need to develop realistic simulation models of the electrochemical interface to understand the interface from an atomistic point-of-view. Here we present a method for obtaining thermodynamic realistic interface structures, a procedure we use to derive specific coverages and to obtain ab initio simulated cyclic voltammograms. As a case study, the method and procedure is applied in a matrix study of three Cu facets in three different electrolytes. The results have been validated by direct comparison to experimental cyclic voltammograms. The alkaline (NaOH) cyclic voltammograms are described by H* and OH*, while in neutral medium (KHCO3 ) the CO 3* species are dominating and in acidic (KCl) the Cl* species prevail. An almost one-to-one mapping is observed from simulation to experiments giving an atomistic understanding of the interface structure of the Cu facets. Atomistic understanding of the interface at relevant eletrolyte conditions will further allow realistic modelling of electrochemical reactions of importance for future eletrocatalytic studies.

Active-Phase Formation and Stability of Gd/Pt(111) Electrocatalysts for Oxygen Reduction: An In Situ Grazing Incidence X-Ray Diffraction Study.

Alloys of platinum and gadolinium present significant activity enhancement over pure Pt for the oxygen reduction reaction (ORR), both in the form of extended electrode surfaces and nanoparticulate catalysts. The active phase consists of a compressed Pt overlayer formed on Pt5 Gd electrodes upon exposure to the electrolyte by acid leaching. Here, we investigate the formation, strain and correlation lengths of the active Pt overlayer by using in situ synchrotron grazing incidence X-ray diffraction on Gd/Pt(111) single-crystalline electrodes. The overlayer forms upon exposure to electrolyte under open circuit conditions; the compressive strain relaxes slightly upon repeated electrochemical cycling in the potential range 0.6 to 1.0 V versus the reversible hydrogen electrode (RHE). In addition, the strain relaxes strongly when exposing the electrode to 1.2 V versus RHE, and the thickness of the crystalline portion of the overlayer increases with potential above 1.3 V versus RHE.

Elucidation of the Oxygen Reduction Volcano in Alkaline Media using a Copper-Platinum(111) Alloy.

The relationship between the binding of the reaction intermediates and oxygen reduction activity in alkaline media was experimentally explored. By introducing Cu into the 2nd surface layer of a Pt(111) single crystal, the surface reactivity was tuned. In both 0.1 m NaOH and 0.1 m KOH, the optimal catalyst should exhibit OH binding circa 0.1 eV weaker than Pt(111), via a Sabatier volcano; this observation suggests that the reaction is mediated via the same surface bound intermediates as in acid, in contrast to previous reports. In 0.1 m KOH, the alloy catalyst at the peak of the volcano exhibits a maximum activity of 101±8 mA cm-2 at 0.9 V vs. a reversible hydrogen electrode (RHE). This activity constitutes a circa 60-fold increase over Pt(111) in 0.1 m HClO4 .

Enabling direct H2O2 production through rational electrocatalyst design.

Future generations require more efficient and localized processes for energy conversion and chemical synthesis. The continuous on-site production of hydrogen peroxide would provide an attractive alternative to the present state-of-the-art, which is based on the complex anthraquinone process. The electrochemical reduction of oxygen to hydrogen peroxide is a particularly promising means of achieving this aim. However, it would require active, selective and stable materials to catalyse the reaction. Although progress has been made in this respect, further improvements through the development of new electrocatalysts are needed. Using density functional theory calculations, we identify Pt-Hg as a promising candidate. Electrochemical measurements on Pt-Hg nanoparticles show more than an order of magnitude improvement in mass activity, that is, A g(-1) precious metal, for H2O2 production, over the best performing catalysts in the literature.

Composition effects of electrodeposited Cu-Ag nanostructured electrocatalysts for CO2 reduction.

The electrochemical carbon dioxide reduction (CO2RR) on Cu-based catalysts is a promising strategy to store renewable electricity and produce valuable C2+ chemicals. We investigate the CO2RR on Cu-Ag nanostructures that have been electrodeposited in a green choline chloride and urea deep eutectic solvent (DES). We determine the electrochemically active surface area (ECSA) using lead underpotential deposition (UPD) to investigate the CO2RR intrinsic activity and selectivity. We show that the addition of Ag on electrodeposited Cu primarily suppresses the production of hydrogen and methane. While the production of carbon monoxide slightly increases, the partial current of the total C2+ products does not considerably increase. Despite that the production rate of C2+ is similar on Cu and Cu-Ag, the addition of Ag enhances the formation of alcohols and oxygenates over ethylene. We highlight the potential of metal electrodeposition from DES as a sustainable strategy to develop bimetallic Cu-based nanocatalysts for CO2RR.

Tailoring the facet distribution on copper with chloride.

Electrocatalytic reactions are sensitive to the catalyst surface structure. Therefore, finding methods to determine active surface sites with different geometry is essential to address the structure-electrocatalytic performance relationships. In this work, we propose a simple methodology to tune and quantify the surface structure on copper catalysts. We tailor the distribution and ratio of facets on copper by electrochemically oxidizing and reducing the surface in chloride-rich aqueous solutions. We then address the formation of new facets with voltammetric lead (Pb) underpotential deposition (UPD). We first record the voltammetric lead UPD on different single facets, which have intense peaks at different potential values. We use this data to decouple each facet peak-contribution in the lead (Pb) UPD curves of the tailored and multifaceted copper surfaces and determine the geometry of the active sites. We combine experiments with density functional theory (DFT) calculations to assess the ligand effect of chloride anions on the copper facet distribution during the surface oxidation/electrodeposition treatment. Our experiments and Wulff constructions suggest that chloride preferentially adsorbs on the (310) facet, reducing the number of (111) sites and inducing the growth of (310) or n(100) × (110) domains. Our work provides a tool to correlate active sites with copper geometries, which is needed to assess the structure-performance relationships in electrocatalysis. We also demonstrate an easy method for selectively tailoring the facet distribution of copper, which is essential to design a well-defined nanostructured catalyst.

Surfactant-Free Colloidal Syntheses of Gold-Based Nanomaterials in Alkaline Water and Mono-alcohol Mixtures.

Gold nanoparticles (Au NPs) and gold-based nanomaterials combine unique properties relevant for medicine, imaging, optics, sensing, catalysis, and energy conversion. While the Turkevich-Frens and Brust-Schiffrin methods remain the state-of-the-art colloidal syntheses of Au NPs, there is a need for more sustainable and tractable synthetic strategies leading to new model systems. In particular, stabilizers are almost systematically used in colloidal syntheses, but they can be detrimental for fundamental and applied studies. Here, a surfactant-free synthesis of size-controlled colloidal Au NPs stable for months is achieved by the simple reduction of HAuCl4 at room temperature in alkaline solutions of low-viscosity mono-alcohols such as ethanol or methanol and water, without the need for any other additives. Palladium (Pd) and bimetallic Au x Pd y NPs, nanocomposites and multimetallic samples, are also obtained and are readily active (electro)catalysts. The multiple benefits over the state-of-the-art syntheses that this simple synthesis bears for fundamental and applied research are highlighted.

Pt5Gd as a highly active and stable catalyst for oxygen electroreduction.

The activity and stability of Pt(5)Gd for the oxygen reduction reaction (ORR) have been studied, using a combination of electrochemical measurements, angle-resolved X-ray photoelectron spectroscopy (AR-XPS), and density functional theory calculations. Sputter-cleaned, polycrystalline Pt(5)Gd shows a 5-fold increase in ORR activity, relative to pure Pt at 0.9 V, approaching the most active in the literature for catalysts prepared in this way. AR-XPS profiles after electrochemical measurements in 0.1 M HClO(4) show the formation of a thick Pt overlayer on the bulk Pt(5)Gd, and the enhanced ORR activity can be explained by means of compressive strain effects. Furthermore, these novel bimetallic electrocatalysts are highly stable, which, in combination with their enhanced activity, makes them very promising for the development of new cathode catalysts for fuel cells.

Correlations between experiments and simulations for formic acid oxidation.

Electrocatalytic conversion of formic acid oxidation to CO2 and the related CO2 reduction to formic acid represent a potential closed carbon-loop based on renewable energy. However, formic acid fuel cells are inhibited by the formation of site-blocking species during the formic acid oxidation reaction. Recent studies have elucidated how the binding of carbon and hydrogen on catalyst surfaces promote CO2 reduction towards CO and formic acid. This has also given fundamental insights into the reverse reaction, i.e. the oxidation of formic acid. In this work, simulations on multiple materials have been combined with formic acid oxidation experiments on electrocatalysts to shed light on the reaction and the accompanying catalytic limitations. We correlate data on different catalysts to show that (i) formate, which is the proposed formic acid oxidation intermediate, has similar binding energetics on Pt, Pd and Ag, while Ag does not work as a catalyst, and (ii) *H adsorbed on the surface results in *CO formation and poisoning through a chemical disproportionation step. Using these results, the fundamental limitations can be revealed and progress our understanding of the mechanism of the formic acid oxidation reaction.

Surfactant-free syntheses and pair distribution function analysis of osmium nanoparticles.

A surfactant-free synthesis of precious metal nanoparticles (NPs) performed in alkaline low-boiling-point solvents has been recently reported. Monoalcohols are here investigated as solvents and reducing agents to obtain colloidal Os nanoparticles by using low-temperature (<100 °C) surfactant-free syntheses. The effect of the precursor (OsCl3 or H2OsCl6), precursor concentration (up to 100 mM), solvent (methanol or ethanol), presence or absence of a base (NaOH), and addition of water (0 to 100 vol %) on the resulting nanomaterials is discussed. It is found that no base is required to obtain Os nanoparticles as opposed to the case of Pt or Ir NPs. The robustness of the synthesis for a precursor concentration up to 100 mM allows for the performance of X-ray total scattering with pair distribution function (PDF) analysis, which shows that 1-2 nm hexagonal close packed (hcp) NPs are formed from chain-like [OsO x Cl y ] complexes.

Tailored electrocatalysts by controlled electrochemical deposition and surface nanostructuring.

Controlled electrodeposition and surface nanostructuring are very promising approaches to tailor the structure of the electrocatalyst surface, with the aim to enhance their efficiency for sustainable energy conversion reactions. In this highlight, we first summarise different strategies to modify the structure of the electrode surface at the atomic and sub-monolayer level for applications in electrocatalysis. We discuss aspects such as structure sensitivity and electronic and geometric effects in electrocatalysis. Nanostructured surfaces are finally introduced as more scalable electrocatalysts, where morphology, cluster size, shape and distribution play an essential role and can be finely tuned. Controlled electrochemical deposition and selective engineering of the surface structure are key to design more active, selective and stable electrocatalysts towards a decarbonised energy scheme.

Importance of Surface IrOx in Stabilizing RuO2 for Oxygen Evolution.

The high precious metal loading and high overpotential of the oxygen evolution reaction (OER) prevents the widespread utilization of polymer electrolyte membrane (PEM) water electrolyzers. Herein we explore the OER activity and stability in acidic electrolyte of a combined IrOx/RuO2 system consisting of RuO2 thin films with submonolayer (1, 2, and 4 Å) amounts of IrOx deposited on top. Operando extended X-ray absorption fine structure (EXAFS) on the Ir L-3 edge revealed a rutile type IrO2 structure with some Ir sites occupied by Ru, IrOx being at the surface of the RuO2 thin film. We monitor corrosion on IrOx/RuO2 thin films by combining electrochemical quartz crystal microbalance (EQCM) with inductively coupled mass spectrometry (ICP-MS). We elucidate the importance of submonolayer surface IrOx in minimizing Ru dissolution. Our work shows that we can tune the surface properties of active OER catalysts, such as RuO2, aiming to achieve higher electrocatalytic stability in PEM electrolyzers.

Operando XAS Study of the Surface Oxidation State on a Monolayer IrOx on RuOx and Ru Oxide Based Nanoparticles for Oxygen Evolution in Acidic Media.

Herein we present surface sensitive operando XAS L-edge measurements on IrOx/RuO2 thin films as well as mass-selected RuOx and Ru nanoparticles. We observed shifts of the white line XAS peak toward higher energies with applied electrochemical potential. Apart from the case of the metallic Ru nanoparticles, the observed potential dependencies were purely core-level shifts caused by a change in oxidation state, which indicates no structural changes. These findings can be explained by different binding energies of oxygenated species on the surface of IrOx and RuOx. Simulated XAS spectra show that the average Ir oxidation state change is strongly affected by the coverage of atomic O. The observed shifts in oxidation state suggest that the surface has a high coverage of O at potentials just below the potential where oxygen evolution is exergonic in free energy. This observation is consistent with the notion that the metal-oxygen bond is stronger than ideal.

Tuning the activity of Pt alloy electrocatalysts by means of the lanthanide contraction.

The high platinum loadings required to compensate for the slow kinetics of the oxygen reduction reaction (ORR) impede the widespread uptake of low-temperature fuel cells in automotive vehicles. We have studied the ORR on eight platinum (Pt)-lanthanide and Pt-alkaline earth electrodes, Pt5M, where M is lanthanum, cerium, samarium, gadolinium, terbium, dysprosium, thulium, or calcium. The materials are among the most active polycrystalline Pt-based catalysts reported, presenting activity enhancement by a factor of 3 to 6 over Pt. The active phase consists of a Pt overlayer formed by acid leaching. The ORR activity versus the bulk lattice parameter follows a high peaked "volcano" relation. We demonstrate how the lanthanide contraction can be used to control strain effects and tune the activity, stability, and reactivity of these materials.

Enhanced electrocatalysis of the oxygen reduction reaction based on patterning of platinum surfaces with cyanide.

The slow rate of the oxygen reduction reaction in the phosphoric acid fuel cell is the main factor limiting its wide application. Here, we present an approach that can be used for the rational design of cathode catalysts with potential use in phosphoric acid fuel cells, or in any environments containing strongly adsorbing tetrahedral anions. This approach is based on molecular patterning of platinum surfaces with cyanide adsorbates that can efficiently block the sites for adsorption of spectator anions while the oxygen reduction reaction proceeds unhindered. We also demonstrate that, depending on the supporting electrolyte anions and cations, on the same CN-covered Pt(111) surface, the oxygen reduction reaction activities can range from a 25-fold increase to a 50-fold decrease. This behaviour is discussed in the light of the role of covalent and non-covalent interactions in controlling the ensemble of platinum active sites required for high turn over rates of the oxygen reduction reaction.