Interplay among work function, electronic structure and stoichiometry in nanostructured VOx films.

The work function is the parameter of greatest interest in many technological applications involving charge exchange mechanisms at the surface. The possibility to produce samples with a controlled work function is then particularly interesting, albeit challenging. We synthetized nanostructured vanadium oxide films by a room temperature supersonic cluster beam deposition method, obtaining samples with tunable stoichiometry and work function (3.7-7 eV). We present an investigation of the electronic structure of several vanadium oxide films as a function of the oxygen content via in situ Auger, valence-band photoemission spectroscopy and work function measurements. The experiments probed the partial 3d density of states, highlighting the presence of strong V 3d-O 2p and V 3d-V 4s hybridizations which influence 3d occupation. We show how controlling the stoichiometry of the sample implies control over work function, and that the access to nanoscale quantum confinement can be exploited to increase the work function of the sample relative to the bulk analogue. In general, the knowledge of the interplay among work function, electronic structure, and stoichiometry is strategic to match nanostructured oxides to their target applications.

Thermal Evolution of ZnS Nanostructures: Effect of Oxidation Phenomena on Structural Features and Photocatalytical Performances.

ZnS nanosystems are being extensively studied for their possible use in a wide range of technological applications. Recently, the gradual oxidation of ZnS to ZnO was exploited to tune their structural, electronic, and functional properties. However, the inherent complexity and size dependence of the ZnS oxidation phenomena resulted in a very fragmented description of the process. In this work, different-sized nanosystems were obtained through two different low temperature wet chemistry routes, namely, hydrothermal and inverse miniemulsion approaches. These protocols were used to obtain ZnS samples consisting of 21 and 7 nm crystallites, respectively, to be used as reference material. The obtained samples were then calcinated at different temperatures, ranging from 400 to 800 °C toward the complete oxidation of ZnO, passing through the coexistence of the two phases (ZnS/ZnO). A thorough comparison of the effects of thermal handling on ZnS structural, chemical, and functional evolution was carried out by TEM, XRD, XAS, XPS, Raman, FT-IR, and UV-Vis. Finally, the photocatalytic activity in the H2 evolution reaction was also compared for selected ZnS and ZnS/ZnO samples. A correlation between size and the oxidation process was observed, as the smaller nanosystems showed the formation of ZnO at lower temperature, or in a larger amount in the case of the ZnS and ZnO co-presence. A difference in the underlying mechanism of the reaction was also evidenced. Despite the ZnS/ZnO mixed samples being characterized by an increased light absorption in the visible range, their photocatalytic activity was found to be much lower.

Efficient room temperature hydrogen sensor based on UV-activated ZnO nano-network.

Room temperature hydrogen sensors were fabricated from Au embedded ZnO nano-networks using a 30 mW GaN ultraviolet LED. The Au-decorated ZnO nano-networks were deposited on a SiO2/Si substrate by a chemical vapour deposition process. X-ray diffraction (XRD) spectrum analysis revealed a hexagonal wurtzite structure of ZnO and presence of Au. The ZnO nanoparticles were interconnected, forming nano-network structures. Au nanoparticles were uniformly distributed on ZnO surfaces, as confirmed by FESEM imaging. Interdigitated electrodes (IDEs) were fabricated on the ZnO nano-networks using optical lithography. Sensor performances were measured with and without UV illumination, at room temperate, with concentrations of hydrogen varying from 5 ppm to 1%. The sensor response was found to be ∼21.5% under UV illumination and 0% without UV at room temperature for low hydrogen concentration of 5 ppm. The UV-photoactivated mode enhanced the adsorption of photo-induced O- and O2- ions, and the d-band electron transition from the Au nanoparticles to ZnO-which increased the chemisorbed reaction between hydrogen and oxygen. The sensor response was also measured at 150 °C (without UV illumination) and found to be ∼18% at 5 ppm. Energy efficient low cost hydrogen sensors can be designed and fabricated with the combination of GaN UV LEDs and ZnO nanostructures.

Effect of gamma irradiation on Schottky-contacted vertically aligned ZnO nanorod-based hydrogen sensor.

We report the impact of gamma irradiation on the performance of a gold Schottky-contacted ZnO nanorod-based hydrogen sensor. RF-sputtered vertically aligned highly c-axis-oriented ZnO NRs were grown on Si(100) substrate. X-ray diffraction shows no significant change in crystal structure at low gamma doses from 1 to 5 kGy. As gamma irradiation doses increase to 10 kGy, the single crystalline ZnO structure converts to polycrystalline. The photoluminescence spectra also shows suppression of the near-band emission peak and the huge wide-band spectrum indicates the generation of structural defects at high gamma doses. At 1 kGy, the hydrogen sensor response was enhanced from 67% to 77% for 1% hydrogen in pure argon at a 150 °C operating temperature. However, at 10 kGy, the relative response decreases to 33.5%. High gamma irradiation causes displacement damage and defects in ZnO NRs, and as a result, degrades the sensor's performance as a result. Low gamma irradiation doses activate the ZnO NR surface through ionization, which enhances the sensor performance. The relative response of the hydrogen sensor was enhanced by ∼14.9% with respect to pristine ZnO using 1 kGy gamma ray treatment.

Visible-light photoactivity of Bi-pyrochlores with high Fe contents.

Three Bi-pyrochlores with different Fe contents (Bi(2)Ti(2)O(7), Bi(1.65)Nb(1.12)Fe(1.16)O(7) and Bi(1.9)Te(0.58)Fe(1.52)O(6.87)) were synthesized in the form of nanopowders with similar morphological characteristics. All three nanopowders show an intensive visible-light photocatalytic activity. The analysis of their band gap and absorption characteristics has shown a strong correlation with the Fe-content indicating that a significant band gap reduction can be obtained by Fe incorporation. The photocatalytic activity has not followed this trend. The initial increase in the Fe-content has resulted in a significant enhancement of the photoactivity while with the further increase the photoactivity has slowly decreased. The reason for this behaviour has been proposed to be in an opposing influence of the increased exciton density and recombination rate.

Adsorption geometry, conformation, and electronic structure of 2H-octaethylporphyrin on Ag(111) and Fe metalation in ultra high vacuum.

Due to the growing interest in the ferromagnetic properties of Fe-octaethylporphyrins (Fe-OEP) for applications in spintronics, methods to produce stable Fe-porphyrins with no Cl atoms are highly demanded. Here, we demonstrate the formation of Fe-OEP layers on Ag(111) single crystal by the ultra high vacuum in situ metalation of the free-base 2H-2,3,7,8,12,13,17,18-octaethylporphyrin (2H-OEP) molecules. The metalation proceeds exactly as in the case of 2H-5,10,15,20-tetraphenylporphyrin (2H-TPP) on the same substrate. An extensive surface characterization by means of X-ray photoemission spectroscopy, valence band photoemission, and NEXAFS with synchrotron radiation light provides information on molecular conformation and electronic structure in the monolayer and multilayer cases. We demonstrate that the presence of the ethyl groups affects the tilt of the adsorbed molecules, the conformation of the macrocycle, and the polarization screening in multilayers, but has only a minor effect in the metalation process with respect to 2H-TPP.

The Role of Lattice Defects on the Optical Properties of TiO2 Nanotube Arrays for Synergistic Water Splitting.

In this study, we report a facile one-step chemical method to synthesize reduced titanium dioxide (TiO2) nanotube arrays (NTAs) with point defects. Treatment with NaBH4 introduces oxygen vacancies (OVs) in the TiO2 lattice. Chemical analysis and optical studies indicate that the OV density can be significantly increased by changing reduction time treatment, leading to higher optical transmission of the TiO2 NTAs and retarded carrier recombination in the photoelectrochemical process. A cathodoluminescence (CL) study of reduced TiO2 (TiO2-x) NTAs revealed that OVs contribute significantly to the emission bands in the visible range. It was found that the TiO2 NTAs reduced for a longer duration exhibited a higher concentration of OVs. A typical CL spectrum of TiO2 was deconvoluted to four Gaussian components, assigned to F, F+, and Ti3+ centers. X-ray photoelectron spectroscopy measurements were used to support the change in the surface chemical bonding and electronic valence band position in TiO2. Electron paramagnetic resonance spectra confirmed the presence of OVs in the TiO2-x sample. The prepared TiO2-x NTAs show an enhanced photocurrent for water splitting due to pronounced light absorption in the visible region, enhanced electrical conductivity, and improved charge transportation.

Silica Coated Bi2Se3 Topological Insulator Nanoparticles: An Alternative Route to Retain Their Optical Properties and Make Them Biocompatible.

Localized surface plasmon resonance (LSPR) is the cause of the photo-thermal effect observed in topological insulator (TI) bismuth selenide (Bi2Se3) nanoparticles. These plasmonic properties, which are thought to be caused by its particular topological surface state (TSS), make the material interesting for application in the field of medical diagnosis and therapy. However, to be applied, the nanoparticles have to be coated with a protective surface layer, which prevents agglomeration and dissolution in the physiological medium. In this work, we investigated the possibility of using silica as a biocompatible coating for Bi2Se3 nanoparticles, instead of the commonly used ethylene-glycol, which, as is presented in this work, is not biocompatible and alters/masks the optical properties of TI. We successfully prepared Bi2Se3 nanoparticles coated with different silica layer thicknesses. Such nanoparticles, except those with a thick, ≈200 nm silica layer, retained their optical properties. Compared to ethylene-glycol coated nanoparticles, these silica coated nanoparticles displayed an improved photo-thermal conversion, which increased with the increasing thickness of the silica layer. To reach the desired temperatures, a 10-100 times lower concentration of photo-thermal nanoparticles was needed. In vitro experiments on erythrocytes and HeLa cells showed that, unlike ethylene glycol coated nanoparticles, silica coated nanoparticles are biocompatible.

Bandgap opening in graphene induced by patterned hydrogen adsorption.

Graphene, a single layer of graphite, has recently attracted considerable attention owing to its remarkable electronic and structural properties and its possible applications in many emerging areas such as graphene-based electronic devices. The charge carriers in graphene behave like massless Dirac fermions, and graphene shows ballistic charge transport, turning it into an ideal material for circuit fabrication. However, graphene lacks a bandgap around the Fermi level, which is the defining concept for semiconductor materials and essential for controlling the conductivity by electronic means. Theory predicts that a tunable bandgap may be engineered by periodic modulations of the graphene lattice, but experimental evidence for this is so far lacking. Here, we demonstrate the existence of a bandgap opening in graphene, induced by the patterned adsorption of atomic hydrogen onto the Moiré superlattice positions of graphene grown on an Ir(111) substrate.

Supramolecular engineering through temperature-induced chemical modification of 2H-tetraphenylporphyrin on Ag(111): flat phenyl conformation and possible dehydrogenation reactions.

Scratching the surface: Formation of a monolayer of 2H-tetraphenylporphyrins (2H-TPP) on Ag(111), either by sublimation of a multilayer in the range 525-600 K or by annealing (at the same temperature) a monolayer deposited at room temperature, induces a chemical modification of the molecules. Rotation of the phenyl rings into a flat conformation is observed and tentatively explained, by using DFT calculations, as a peculiar reaction due to molecular dehydrogenation.

The Role of Substrate on Thermal Evolution of Ag/TiO2 Nanogranular Thin Films.

In multicomponent thin films, properties and functionalities related to post-deposition annealing treatments, such as thermal stability, optical absorption and surface morphology are typically rationalized, neglecting the role of the substrate. Here, we show the role of the substrate in determining the temperature dependent behaviour of a paradigmatic two-component nanogranular thin film (Ag/TiO2) deposited by gas phase supersonic cluster beam deposition (SCBD) on silica and sapphire. Up to 600 °C, no TiO2 grain growth nor crystallization is observed, likely inhibited by the Zener pinning pressure exerted by the Ag nanoparticles on the TiO2 grain boundaries. Above 600 °C, grain coalescence, formation of However, the two substrates steer the evolution of the film morphology and optical properties in two different directions. anatase and rutile phases and drastic modification of the optical absorption are observed. On silica, Ag is still present as NPs distributed into the TiO2 matrix, while on sapphire, hundreds of nm wide Ag aggregates appear on the film surface. Moreover, the silica-deposited film shows a broad absorption band in the visible range while the sapphire-deposited film becomes almost transparent for wavelengths above 380 nm. We discuss this result in terms of substrate differences in thermal conductivity, thermal expansion coefficient and Ag diffusivity. The study of the substrate role during annealing is possible since SCBD allows the synthesis of the same film independently of the substrate, and suggests new perspectives on the thermodynamics and physical exchanges between thin films and their substrates during heat treatments.

Enhancing the Mechanical Properties of Biodegradable Mg Alloys Processed by Warm HPT and Thermal Treatments.

In this study, several biodegradable Mg alloys (Mg5Zn, Mg5Zn0.3Ca, Mg5Zn0.15Ca, and Mg5Zn0.15Ca0.15Zr, numbers in wt%) were investigated after thermomechanical processing via high-pressure torsion (HPT) at elevated temperature as well as after additional heat treatments. Indirect and direct analyses of microstructure revealed that the significant strength increases arise not only from dislocations and precipitates but also from vacancy agglomerates. By contrast with former low-temperature processing routes applied by the authors, a significant ductility was obtained because of temperature-induced dynamic recovery. The low initial values of Young's modulus were not significantly affected by warm HPT-processing. nor by heat treatments afterwards. Also, corrosion resistance did not change or even increase during those treatments. Altogether, the study reveals a viable processing route for the optimization of Mg alloys to provide enhanced mechanical properties while leaving the corrosion properties unaffected, suggesting it for the use as biodegradable implant material.

Substrate influence for the Zn-tetraphenyl-porphyrin adsorption geometry and the interface-induced electron transfer.

In molecular devices, the importance of interfaces cannot be neglected as they determine charge injection and charge flow and, therefore, the device performance. Herein we report on the interaction of one single layer of Zn-tetraphenyl-porphyrin with Ag(110) and Si(111). Photoemission, near-edge X-ray absorption, and resonant photoemission are used to study the bonding nature, the adsorption geometry as well as the dynamics of electron transfer between the molecules and the metal or semiconductor surfaces. Molecule-substrate charge transfer is driven by the overlap with the molecular pi orbitals. In particular, the coupling of the phenyl legs with the substrate and the relative excited charge injection are dramatically different for the two surfaces considered.

Impact of urbanization and steel mill emissions on elemental composition of street dust and corresponding particle characterization.

Street Dust (SD) acts as a sink and source of atmospheric particles containing Potentially Toxic Elements (PTEs) and can pose a possible pathway of PTEs to human bodies. Comprehensive SD study, where 249 samples were collected from rural, urban and industrialized areas aimed to increase the understanding between sedimentation of atmospheric dust derived from anthropogenic activities and elemental composition of SD. Elemental composition for 53 elements (ICP-MS, aqua regia digestion) was determined on fraction <0.063 mm. Significantly increased levels of Sn-Cu-Sb-Bi-Ag-Ba-Mo-Pt-Pb and other elements have been detected in urban environments, compared to the rural ones. SEM/EDS investigation identified that main carriers of Ba, Cu and Sn are most likely particles derived from non-exhaust traffic emissions. Areas around steel mills show a strong enrichment with Cr, Mo, Ni and W, which exponentially decreases with the increased distance from the plant, reaching corresponding urban background 15 and 20 km from the source. SEM/EDS inspection identified spherical and melted irregular particles as the main carriers of the above-mentioned elements. City managers shall adapt measures to reduce amount of vehicular traffic and quantity of deposited SD on the public surfaces and encourage green city planning, while industrial emitters are encouraged to reduce their dust emissions.

Inherent Surface Properties of Adsorbent-Free Ultrathin Bi2Se3 Topological Insulator Platelets.

We report on a hydrothermal synthesis of hexagonal ultra-thin Bi2Se3 platelets, which was performed without any organic reactants. The synthesis resulted in the particles with a surface, clean of any organic adsorbents, which was confirmed with a high-resolution transmission electron microscopy, zeta-potential measurements and thermogravimetric measurements coupled with a mass spectroscopy. Due to the absence of the adsorbed organic layer on the Bi2Se3 platelet surface, we were able to measure their inherent surface and optical properties. So far this has not been possible as it has been believed that such hexagonal Bi2Se3 platelets can only be prepared by a solvothermal synthesis, for which it was unable to avoid the organic surface layer. Here we explain the mechanism behind the successful hydrothermal synthesis and show a striking difference in zeta potential behaviour and UV-vis absorption characteristics caused by the adsorbed layer. The surface of the hydrothermally synthesized Bi2Se3 platelets was so clean to enable the occurrence of the localized surface plasmon resonance due to the bulk and topological surface electronic states.

A DNA origami plasmonic sensor with environment-independent read-out.

DNA origami is a promising technology for its reproducibility, flexibility, scalability and biocompatibility. Among the several potential applications, DNA origami has been proposed as a tool for drug delivery and as a contrast agent, since a conformational change upon specific target interaction may be used to release a drug or produce a physical signal, respectively. However, its conformation should be robust with respect to the properties of the medium in which either the recognition or the read-out take place, such as pressure, viscosity and any other unspecific interaction other than the desired target recognition. Here we report on the read-out robustness of a tetragonal DNA-origami/gold-nanoparticle hybrid structure able to change its configuration, which is transduced in a change of its plasmonic properties, upon interaction with a specific DNA target. We investigated its response when analyzed in three different media: aqueous solution, solid support and viscous gel. We show that, once a conformational variation is produced, it remains unaffected by the subsequent physical interactions with the environment.

Study of silica-based intrinsically emitting nanoparticles produced by an excimer laser.

We report an experimental study demonstrating the feasibility to produce both pure and Ge-doped silica nanoparticles (size ranging from tens up to hundreds of nanometers) using nanosecond pulsed KrF laser ablation of bulk glass. In particular, pure silica nanoparticles were produced using a laser pulse energy of 400 mJ on pure silica, whereas Ge-doped nanoparticles were obtained using 33 and 165 mJ per pulse on germanosilicate glass. The difference in the required energy is attributed to the Ge doping, which modifies the optical properties of the silica by facilitating energy absorption processes such as multiphoton absorption or by introducing absorbing point defects. Defect generation in bulk pure silica before nanoparticle production starts is also suggested by our results. Regarding the Ge-doped samples, scanning electron microscopy (SEM) and cathodoluminescence (CL) investigations revealed a good correspondence between the morphology of the generated particles and their emission signal due to the germanium lone pair center (GLPC), regardless of the energy per pulse used for their production. This suggests a reasonable homogeneity of the emission features of the samples. Similarly, energy dispersive X-ray spectroscopy (EDX) data showed that the O, Ge and Si signals qualitatively correspond to the particle morphology, suggesting a generally uniform chemical composition of the Ge-doped samples. No significant CL signal could be detected in pure silica nanoparticles, evidencing the positive impact of Ge for the development of intrinsically emitting nanoparticles. Transmission electron microscope (TEM) data suggested that the Ge-doped silica nanoparticles are amorphous. SEM and TEM data evidenced that the produced nanoparticles tend to be slightly more spherical in shape for a higher energy per pulse. Scanning transmission electron microscope (STEM) data have shown that, regardless of size and applied energy per pulse, in each nanoparticle, some inhomogeneity is present in the form of brighter (i.e., more dense) features of a few nanometers.

TiO2-SnS2 nanocomposites: solar-active photocatalytic materials for water treatment.

The study is aimed at evaluating TiO2-SnS2 composites as effective solar-active photocatalysts for water treatment. Two strategies for the preparation of TiO2-SnS2 composites were examined: (i) in-situ chemical synthesis followed by immobilization on glass plates and (ii) binding of two components (TiO2 and SnS2) within the immobilization step. The as-prepared TiO2-SnS2 composites and their sole components (TiO2 or SnS2) were inspected for composition, crystallinity, and morphology using Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX) analyses. Diffuse reflectance spectroscopy (DRS) was used to determine band gaps of immobilized TiO2-SnS2 and to establish the changes in comparison to respective sole components. The activity of immobilized TiO2-SnS2 composites was tested for the removal of diclofenac (DCF) in aqueous solution under simulated solar irradiation and compared with that of single component photocatalysts. In situ chemical synthesis yielded materials of high crystallinity, while their morphology and composition strongly depended on synthesis conditions applied. TiO2-SnS2 composites exhibited higher activity toward DCF removal and conversion in comparison to their sole components at acidic pH, while only in situ synthesized TiO2-SnS2 composites showed higher activity at neutral pH.

Molecular size and solubility conditions of polysilane macromolecules with different topology.

Solubility of polysilane macromolecules has so far been a scientific as well as technological problem due to a lack of understanding of their proper molecular size and agglomeration/de-agglomeration conditions. Here we show that, in contrary to previous reports, the polysilane molecules are inherently small enough to be, under right conditions, dissolved. We used a dynamic light scattering and a differential scanning calorimetry to show that even under a dilute regime the polymer molecules are agglomerated at room temperature and undergo de-agglomeration at slightly elevated temperatures of around 40 °C. The de-agglomeration results in formation of stable solutions of the polymer molecules of different topological structure in different organic solvents. We determined the polymer molecular sizes to be around 20 nm, much lower than previously reported. The measured molecular size was confirmed by transmission electron microscope imaging of the individual molecules.

Solar-driven photocatalytic treatment of diclofenac using immobilized TiO2-based zeolite composites.

The study is aimed at evaluating the potential of immobilized TiO2-based zeolite composite for solar-driven photocatalytic water treatment. In that purpose, TiO2-iron-exchanged zeolite (FeZ) composite was prepared using commercial Aeroxide TiO2 P25 and iron-exchanged zeolite of ZSM5 type, FeZ. The activity of TiO2-FeZ, immobilized on glass support, was evaluated under solar irradiation for removal of diclofenac (DCF) in water. TiO2-FeZ immobilized in a form of thin film was characterized for its morphology, structure, and composition using scanning electron microscopy/energy-dispersive x-ray spectroscopy (SEM/EDX). Diffuse reflectance spectroscopy (DRS) was used to determine potential changes in band gaps of prepared TiO2-FeZ in comparison to pure TiO2. The influence of pH, concentration of hydrogen peroxide, FeZ wt% within the composite, and photocatalyst dosage on DCF removal and conversion efficiency by solar/TiO2-FeZ/H2O2 process was investigated. TiO2-FeZ demonstrated higher photocatalytic activity than pure TiO2 under solar irradiation in acidic conditions and presence of H2O2.