Bio-Based Poly(hydroxy urethane)s for Efficient Organic High-Power Energy Storage.

Fast, low-cost, and efficient energy storage technologies are urgently needed to balance the intermittence of sustainable energy sources. High-power capacitors using organic polymers offer a green and scalable answer. They require dielectrics with high permittivity (εr) and breakdown strength (EB), which bio-based poly(hydroxy urethane)s (PHUs) can provide. PHUs combine high concentrations of hydroxyl and carbamate groups, thus enhancing their εr, and a highly tunable glass transition (Tg), which dictates the regions of low dielectric losses. By reacting erythritol dicarbonate with bio-based diamines, fully bio-based PHUs were synthesized with Tg ∼ 50 °C, εr > 8, EB > 400 MV·m-1, and low losses (tan δ < 0.03). This results in energy storage performance comparable with the flagship petrochemical materials (discharge energy density, Ue > 6 J·cm-3) combined with a remarkably high discharge efficiency, with η = 85% at EB and up to 91% at 0.5 EB. These bio-based PHUs thus represent a highly promising route to green and sustainable energy storage.

Synthesis and Characterization of Vanillin-Based π-Conjugated Polyazomethines and Their Oligomer Model Compounds.

The synthesis of π-conjugated polymers via an environmentally friendly procedure is generally challenging. Herein, we describe the synthesis of divanillin-based polyazomethines, which are derived from a potentially bio-based monomer. The polymerization is performed in 5 min under microwave irradiation without any metallic catalyst, with water as the only by-product. The vanillin-based polyazomethines were characterized by SEC, TGA, and UV-Vis spectroscopy. Model compounds were designed and characterized by X-ray diffraction and UV-Vis spectroscopy. The structure/properties study of vanillin-based azomethines used as models allowed us to unequivocally confirm the E configuration and to highlight the cross-conjugated nature of divanillin-based polymers.

Enantioselective Crystallization of Diglycerol Dicarbonate: Impact of the Microstructure on Polyhydroxyurethane Properties.

Bicylic carbonates are precursors employed in non-isocyanate polyurethane syntheses, namely polyhydroxyurethanes (PHUs) and, among them, ether-activated biobased diglycerol dicarbonate (DGDC) is widely investigated. Herein, the original separation of DGDC stereoisomers, thanks to a recrystallization procedure, leading to enantiomers having different crystal lattices, that is, square transparent crystals and needle-like structures, respectively, is reported. In this study, the separation and the characterization of the two crystal structures is first discussed and, second, the impact of the stereochemistry of DGDC on the corresponding PHUs properties is investigated.

Synthesis and Self-Assembly of Xylan-Based Amphiphiles: From Bio-Based Vesicles to Antifungal Properties.

This work aims at designing functional biomaterials through selective chemical modification of xylan from beechwood. Acidic hydrolysis of xylan led to well-defined oligomers with an average of six xylose units per chain and with an aldehyde group at the reductive end. Reductive amination was performed on this aldehyde end group to introduce an azide reactive group. "Click chemistry" was then applied to couple these hydrophilic xylans moieties with different hydrophobic fatty acid methyl esters that were previously functionalized with complementary alkyne functions. The resulting amphiphilic bio-based conjugates were then self-assembled using three different methods, namely, direct solubilization, thin-film rehydration/extrusion, and microfluidics. Well-defined micelles and vesicles were obtained, and their high loading capacity with propiconazole as an antifungal active molecule was shown. The resulting vesicles loaded with propiconazole in a microfluidic process proved to significantly improve the antifungal activity of propiconazole, demonstrating the high potential of such xylan-based amphiphiles.

Bio-Based Thermo-Reversible Aliphatic Polycarbonate Network.

Aliphatic polycarbonates represent an important class of materials with notable applications in the biomedical field. In this work, low Tg furan-functionalized bio-based aliphatic polycarbonates were cross-linked thanks to the Diels-Alder (DA) reaction with a bis-maleimide as the cross-linking agent. The thermo-reversible DA reaction allowed for the preparation of reversible cross-linked polycarbonate materials with tuneable properties as a function of the pendent furan content that was grafted on the polycarbonate backbone. The possibility to decrosslink the network around 70 °C could be an advantage for biomedical applications, despite the rather poor thermal stability of the furan-functionalized cross-linked polycarbonates.

From Lignin-derived Aromatic Compounds to Novel Biobased Polymers.

Nowadays, the synthesis of (semi)aromatic polymers from lignin derivatives is of major interest, as aromatic compounds are key intermediates in the manufacture of polymers and lignin is the main source of aromatic biobased substrates. Phenols with a variety of chemical structures can be obtained from lignin deconstruction; among them, vanillin and ferulic acid are the main ones. Depending on the phenol substrates, different chemical modifications and polymerization pathways are developed, leading to (semi)aromatic polymers covering a wide range of thermomechanical properties. This review discusses the synthesis and properties of thermosets (vinyl ester resins, cyanate ester, epoxy, and benzoxazine resins) and thermoplastic polymers (polyesters, polyanhydrides, Schiff base polymers, polyacetals, polyoxalates, polycarbonates, acrylate polymers) prepared from vanillin, ferulic acid, guaiacol, syringaldehyde, or 4-hydroxybenzoic acid.

Bio-based aliphatic polyurethanes through ADMET polymerization in bulk and green solvent.

A new route to α,ω-diene urethane monomer is proposed by converting 10-undecenoic acid into the corresponding acyl azide, followed by urethanization with 10-undecenol. ADMET polymerizations of this α,ω-diene urethane monomer as well as other bio-based α,ω-dienes bearing various organic functions (ester, carbonate, ether, amide) were carried out in bulk and solution conditions. A screening of the most commonly used metathesis catalysts allows to evaluate their tolerance toward the urethane function as well as toward Polarclean, a "green" and nontoxic high boiling point solvent. The influence of the nature of the central organic function in these α,ω-diene monomers on the thermomechanical properties is investigated.

New insights into the impact of leachates from in-field collected plastics on aquatic invertebrates and vertebrates.

The impact of leachates from micronized beached plastics of the Mediterranean Sea and Atlantic Ocean on coastal marine ecosystems was investigated by using a multidisciplinary approach. Chemical analysis and ecotoxicological tests on phylogenetically distant species were performed on leachates from the following plastic categories: bottles, pellets, hard plastic (HP) containers, fishing nets (FN) and rapido trawling rubber (RTR). The bacteria Alivibrio fischeri, the nauplii of the crustaceans Amphibalanus amphitrite and Acartia tonsa, the rotifer Brachionus plicatilis, the embryos of the sea urchin Paracentrotus lividus, the ephyrae of the jellyfish Aurelia sp. and the larvae of the medaka Oryzias latipes were exposed to different concentrations of leachates to evaluate lethal and sub-lethal effects. Thirty-one additives were identified in the plastic leachates; benzophenone, benzyl butyl phthalate and ethylparaben were present in all leachates. Ecotoxicity of leachates varied among plastic categories and areas, being RTR, HP and FN more toxic than plastic bottles and pellets to several marine invertebrates. The ecotoxicological results based on 13 endpoints were elaborated within a quantitative weight of evidence (WOE) model, providing a synthetic hazard index for each data typology, before their integrations in an environmental risk index. The WOE assigned a moderate and slight hazard to organisms exposed to leachates of FN and HP collected in the Mediterranean Sea respectively, and a moderate hazard to leachates of HP from the Atlantic Ocean. No hazard was found for pellet, bottles and RTR. These findings suggest that an integrated approach based on WOE on a large set of bioassays is recommended to get a more reliable assessment of the ecotoxicity of beached-plastic leachates. In addition, the additives leached from FN and HP should be further investigated to reduce high concentrations and additive types that could impact marine ecosystem health.

Complexation in Aqueous Solution of a Hydrophobic Polyanion (PSSNa) Bearing Different Charge Densities with a Hydrophilic Polycation (PDADMAC).

In this work the electrostatic complexation of two strong polyelectrolytes (PEs) was studied, the hydrophilic and positively charged poly (diallyldimethylammonium chloride) (PDADMAC) and the hydrophobic and negatively charged poly (styrene-co-sodium styrene sulfonate) (P(St-co-SSNa)), which was prepared at different sulfonation rates. The latter is known to adopt a pearl necklace conformation in solution for intermediate sulfonation rates, suggesting that a fraction of the P(St-co-SSNa) charges might be trapped in these hydrophobic domains; thus making them unavailable for complexation. The set of complementary techniques (DLS, zetametry, ITC, binding experiment with a cationic and metachromatic dye) used in this work highlighted that this was not the case and that all anionic charges of P(St-co-SSNa) were in fact available for complexation either with the polycationic PDADMAC or the monocationic o-toluidine blue dye. Only minor differences were observed between these techniques, consistently showing a complexation stoichiometry close to 1:1 at the charge equivalence for the different P(St-co-SSNa) compositions. A key result emphasizing that (i) the strength of the electrostatic interaction overcomes the hydrophobic effect responsible for pearl formation, and (ii) the efficiency of complexation does not depend significantly on differences in charge density between PDADMAC and P(St-co-SSNa), highlighting that PE chains can undergo conformational rearrangements favoring the juxtaposition of segments of opposite charge. Finally, these data have shown that the formation of colloidal PECs, such as PDADMAC and P(St-co-SSNa), occurs in two distinct steps with the formation of small primary complex particles (<50 nm) by pairing of opposite charges (exothermic step) followed by their aggregation within finite-size clusters (endothermic step). This observation is in agreement with the previously described mechanism of PEC particle formation from strongly interacting systems containing a hydrophobic PE.

Oxidative Depolymerization of Alkaline Lignin from Pinus Pinaster by Oxygen and Air for Value-Added Bio-Sourced Synthons.

In this work, an efficient 3-step process targeting the chemical modification and purification of lignin oligomers from industrial alkaline lignin is described. The oxidative depolymerization process of alkaline lignin with O2 or Air pressure, without use of metal catalyst, led to the production of two fractions of lignin oligomers named 'precipitated lignin' and 'hydrosoluble lignin' with 40% and 60% yield, respectively. These fractions were characterized with a wide range of methods including NMR spectroscopy (31P, 2D-HSQC), SEC (in basic media), FTIR. NMR analyses revealed the presence of carboxylic acid functions at a ratio of 1.80 mmol/g and 2.80 mmol/g for the precipitated and hydrosoluble lignin, respectively, values much higher than what is generally found in native lignin (between 0.2 and 0.5 mmol/g). SEC analyses revealed the formation of low molar masses for the precipitated (2200 g/mol) and hydrosoluble fractions (1500 g/mol) in contrast to the alkaline lignin (3900 g/mol). It is worth noting that the hydrosoluble fraction of lignin is soluble in water at any pH. Both processes (oxygen and air) were successfully scaled up and showed similar results in terms of yield and functionalization.

Supercritical behavior in free radical polymerization of ethylene in the medium pressure range.

Free radical polymerization of ethylene in an intermediate pressure and temperature range (P(ethylene) < 250 bar and 50 °C < T < 90 °C) in the presence of an organic solvent has been studied. Under selected conditions (P, T) and according to the amount of organic solvent added, either a supercritical monophasic or a biphasic medium is obtained. In the case of a biphasic medium, polymerization occurred in the liquid phase in which radical initiator and ethylenes are dissolved. The transition between a monophasic to a biphasic medium has been predicted using thermodynamic calculations and has been related to experimental observations such as the dependence of polymerization activity versus solvent volume.

UV-protection from chitosan derivatized lignin multilayer thin film.

Lignin is one of the most abundant renewable materials on the earth. Despite possessing useful antioxidant and UV absorbing properties, its effective utilization in technology has been hampered by its relative insolubility and difficulty to process. In this work, a simple chemical derivatization process is utilized which yields water-soluble lignin possessing anionic carboxylate groups. These carboxylate groups give lignin polyanionic behavior and enable its utilization in the growth of a functional film via layer-by-layer (LbL) assembly with biologically sourced chitosan. The growth mechanism of this film is hypothesized to be a result of both hydrogen bonding and ionic interactions. The film demonstrates excellent UV-absorptive capability. A 100 nm thick chitosan/lignin coating was applied to a poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) film and shown to reduce its degradation sixfold over the course of a 1 hour exposure to harsh UV light. This is the first demonstration of lignin being utilized in a fully biologically derived LbL film. Utilization of lignin in LbL assembly is an important step in the development of renewable nanotechnology.

Divanillin-Based Polyazomethines: Toward Biobased and Metal-Free π-Conjugated Polymers.

Divanillin was synthesized in high yield and purity using Laccase from Trametes versicolor. It was then polymerized with benzene-1,4-diamine and 2,7-diaminocarbazole to form polyazomethines. Polymerizations were performed under microwave irradiation and without transition-metal-based catalysts. These biobased conjugated polyazomethines present a broad fluorescence spectrum ranging from 400 to 600 nm. Depending on the co-monomer used, polyazomethines with molar masses of around 10 kg·mol-1 and with electronic gaps ranging from 2.66 to 2.85 eV were obtained. Furthermore, time-dependent density functional theory (TD-DFT) calculations were performed to corroborate the experimental results.

Divanillin-Based Aromatic Amines: Synthesis and Use as Curing Agents for Fully Vanillin-Based Epoxy Thermosets.

Bio-based aromatic diamines from vanillin substrate were successfully synthesized and characterized. These amines, i.e., methylated divanillylamine (MDVA) and 3,4-dimethoxydianiline (DMAN), were then tested as curing agents for the design of bio-based epoxy thermosets. The epoxy thermosets obtained from these novel vanillin-based amines exhibited promising thermomechanical properties in terms of glass transition temperature and char residue.

Versatile cross-linked fatty acid-based polycarbonate networks obtained by thiol-ene coupling reaction.

Bio-sourced polycarbonate networks have been synthesized from an alkene-functional fatty-acid based polycarbonate precursor. Cross-linked networks were created using the radical thiol-ene coupling reaction. The resulting polycarbonate materials exhibited versatile properties either influenced by the structure of the cross-linker or the cross-linker/olefin unit ratio. Indeed, the storage modulus above the glass transition temperature could be modulated from 0.9 to 8.9 MPa only by changing the type of cross-linker, i.e. 1,9-nonanedithiol vs. 1,4-benzenedimethanethiol. The cross-linker/olefin unit ratio was also shown to largely impact the polycarbonate networks properties. An elongation at break of nearly 200% was reached when a low cross-linker/olefin ratio was applied. Moreover, functional polycarbonate networks bearing pendant thiol groups were obtained when an excess of dithiol was used with respect to olefin groups.

Visible-light photocatalyzed oxidative decarboxylation of oxamic acids: a green route to urethanes and ureas.

A sustainable metal-free route to urethanes and ureas based on a photocatalyzed oxidative decarboxylation of oxamic acids is described. The reaction includes in situ generation of an isocyanate from the oxamic acid, using an organic dye as a photocatalyst, a hypervalent iodine reagent as an oxidant and a light source, which trigger the free-radical decarboxylation. This protocol successfully avoids the isolation, purification and storage of carcinogenic isocyanates and allows elaboration of urethanes and ureas in a one-pot process from commercially available sources.

On the direct use of CO2 in multicomponent reactions: introducing the Passerini four component reaction.

We introduce a novel isocyanide-based multicomponent reaction, the Passerini four component reaction (P-4CR), by replacing the carboxylic acid component of a conventional Passerini three component reaction (P-3CR) with an alcohol and CO2. Key to this approach is the use of a switchable solvent system, allowing the synthesis of a variety of α-carbonate-amides. The reaction was first investigated and optimized using butanol, isobutyraldehyde, tert-butyl isocyanide and CO2. Parameters investigated included the effect of reactant equivalents, reactant concentration, solvent, catalyst, catalyst concentration and CO2 pressure. Of the other parameters, the purity of the aldehyde and its tendency to oxidize was one of the most critical parameters for a successful P-4CR. After optimization, a total of twelve (12) P-4CR compounds were synthesized with conversions ranging between 16 and 82% and isolated yields between 18 and 43%. Their structures were confirmed via 1H and 13C NMR, FT-IR and high resolution mass spectrometry (ESI-MS). In addition, three (3) hydrolysis products of P-4CR (α-hydroxyl-amides) were successfully isolated with yields between 23 and 63% and fully characterized (1H, 13C NMR, FT-IR and ESI-MS) as well.

Simple and Efficient Approach toward Photosensitive Biobased Aliphatic Polycarbonate Materials.

Fatty acids were used as precursors for the synthesis of photosensitive polycarbonate materials. In order to avoid multistep reactions, a simple and straightforward methodology toward the synthesis of photosensitive monomers has been developed. Hence, a fatty acid-based cyclic carbonate bearing an unsaturation was synthesized and subsequently polymerized in a controlled manner (D = 1.07) by organo-catalyzed ring-opening polymerization (ROP). A thio-cinnamate derivative was then readily synthesized via a one-pot reaction and grafted onto the polycarbonate backbone by thiol-ene reaction. The content of photoresponsive cinnamoyl moiety grafted on the polycarbonate was tunable with the reaction time. Such functionalized polycarbonates could be crosslinked (by UV irradiation at 365 nm) and partially decrosslinked (irradiated at 254 nm) and exhibit versatile properties ranging from rather tough materials to elastomeric networks with respect to the content of the photosensitive cinnamoyl moiety grafted on the polymer.