Facile route to bulk ultrafine-grain steels for high strength and ductility.

Steels with sub-micrometre grain sizes usually possess high toughness and strength, which makes them promising for lightweighting technologies and energy-saving strategies. So far, the industrial fabrication of ultrafine-grained (UFG) alloys, which generally relies on the manipulation of diffusional phase transformation, has been limited to steels with austenite-to-ferrite transformation1-3. Moreover, the limited work hardening and uniform elongation of these UFG steels1,4,5 hinder their widespread application. Here we report the facile mass production of UFG structures in a typical Fe-22Mn-0.6C twinning-induced plasticity steel by minor Cu alloying and manipulation of the recrystallization process through the intragranular nanoprecipitation (within 30 seconds) of a coherent disordered Cu-rich phase. The rapid and copious nanoprecipitation not only prevents the growth of the freshly recrystallized sub-micrometre grains but also enhances the thermal stability of the obtained UFG structure through the Zener pinning mechanism6. Moreover, owing to their full coherency and disordered nature, the precipitates exhibit weak interactions with dislocations under loading. This approach enables the preparation of a fully recrystallized UFG structure with a grain size of 800 ± 400 nanometres without the introduction of detrimental lattice defects such as brittle particles and segregated boundaries. Compared with the steel to which no Cu was added, the yield strength of the UFG structure was doubled to around 710 megapascals, with a uniform ductility of 45 per cent and a tensile strength of around 2,000 megapascals. This grain-refinement concept should be extendable to other alloy systems, and the manufacturing processes can be readily applied to existing industrial production lines.

pH Stimuli-Responsive, Rapidly Self-healable Coatings Enhanced the Corrosion Resistance and Osteogenic Differentiation of Mg-1Ca Osteoimplant.

Mg-Ca alloys have emerged as a promising research direction for biomedical implants in the orthopedic field. However, their clinical use is deterred by their fast corrosion rate. In this work, a pH stimuli-responsive silk-halloysite (HNT)/phytic acid (PA) self-healing coating (Silk-HNT/PA) is constructed to slow down the corrosion rate of Mg-1Ca alloy and its cell viability and osteogenic differentiation ability are enhanced. The Silk-HNT/PA coating exhibits appealing active corrosion protection, by eliciting pH-triggerable self-healing effects, while simultaneously affording superior biocompatibility and osteogenic differentiation ability. Moreover, in vivo studies by histological analysis also demonstrate better osseointegration for the Silk-HNT/PA coated Mg-1Ca alloy. In summary, the Silk-HNT/PA coating in the present study has great potential in enhancing the biomedical utility of Mg alloys.

Tailoring ZE21B Alloy with Nature-Inspired Extracellular Matrix Secreted by Micro-Patterned Smooth Muscle Cells and Endothelial Cells to Promote Surface Biocompatibility.

Delayed surface endothelialization is a bottleneck that restricts the further application of cardiovascular stents. It has been reported that the nature-inspired extracellular matrix (ECM) secreted by the hyaluronic acid (HA) micro-patterned smooth muscle cells (SMC) and endothelial cells (EC) can significantly promote surface endothelialization. However, this ECM coating obtained by decellularized method (dECM) is difficult to obtain directly on the surface of degradable magnesium (Mg) alloy. In this study, the method of obtaining bionic dECM by micro-patterning SMC/EC was further improved, and the nature-inspired ECM was prepared onto the Mg-Zn-Y-Nd (ZE21B) alloy surface by self-assembly. The results showed that the ECM coating not only improved surface endothelialization of ZE21B alloy, but also presented better blood compatibility, anti-hyperplasia, and anti-inflammation functions. The innovation and significance of the study is to overcome the disadvantage of traditional dECM coating and further expand the application of dECM coating to the surface of degradable materials and materials with different shapes.

Rapid screening alloying elements for improved corrosion resistance on the Mg(0001) surface using first principles calculations.

The poor corrosion resistance of Mg alloys is a major challenge for their applications. The corrosion of Mg alloys is mainly controlled by the anodic dissolution of Mg and the cathodic hydrogen evolution reaction (HER), which is closely related to the stability and the hydrogen adsorption of the Mg surface. In this work, the effects of alloying elements (As, Ge, Cd, Zn, Ga, Al, and Y) on the stability and the hydrogen adsorption of a Mg(0001) surface have been studied based on first principles calculations. We have developed a horizontally integrated approach to evaluate their effects on corrosion resistance using parameters such as the surface energy, vacancy formation energy, Bader charge, electron density distribution, and the adsorption free energy of H atom at different adsorbed sites. We found that the doped atoms could significantly change the surface atomic structure and electron transfer on the Mg surface. These behaviors modified the energy required to detach the nearest neighbors of doped atoms from the Mg surface, the adsorption free energy of H atoms, and the stable adsorption sites of H atoms on the Mg surface, which regulate the corrosion resistance of Mg alloys. Interestingly, we found that Y doping on the Mg surface increased the corrosion resistance and our new method had tremendous potential in the rapid screening of alloying elements that could improve the stability of Mg alloys and inhibit the hydrogen evolution reaction.

Investigation of Mg-xLi-Zn alloys for potential application of biodegradable bone implant materials.

Implant therapy after osteosarcoma surgery is a major clinical challenge currently, especially the requirements for mechanical properties, degradability of the implants, and their inhibition of residual tumor cells. Biodegradable magnesium (Mg) alloy as medical bone implant material has full advantages and huge potential development space. Wherein, Mg-lithium (Li) based alloy, as an ultra-light alloy, has good properties for implants under certain conditions, and both Mg and Li have inhibitory effects on tumor cells. Therefore, Mg-Li alloy is expected to be applied in bone implant materials for mechanical supporting and inhibiting tumor cells simultaneously. In this contribution, the Mg-xLi-Zinc (Zn) series alloys (x = 3 wt%, 6 wt%, 9 wt%) were prepared to study the influence of different elements and contents on the structure and properties of the alloy, and the biosafety of the alloy was also evaluated. Our data showed that the yield strength, tensile strength, and elongation of as-cast Mg-xLi-Zn alloy were higher than those of as-cast Mg-Zn alloy; Mg-xLi-Zn alloy can kill osteosarcoma cells (MG-63) in a concentration-dependent manner, wherein Mg-3Li-Zn alloy (x = 3 wt%) and Mg-6Li-Zn alloy (x = 6 wt%) promoted the proliferation of osteoblasts (MC3T3) at a certain concentration of Li. In summary, our study demonstrated that the Mg-6Li-Zn alloy could be potentially applied as a material of orthopedic implant for its excellent multi-functions.

Stronger Adsorption of Phosphorothioate DNA Oligonucleotides on Graphene Oxide by van der Waals Forces.

Finding DNA sequences that can adsorb strongly on nanomaterials is critical for bioconjugate and biointerface chemistry. In most previous work, unmodified DNA with a phosphodiester backbone (PO DNA) were screened or selected for adsorption on inorganic surfaces. In this work, the adsorption of phosphorothioate (PS)-modified DNA (PS DNA) on graphene oxide (GO) is studied. By use of fluorescently labeled oligonucleotides as probes, all the tested PS DNA strands are adsorbed more strongly on GO compared to the PO DNA of the same sequence. The adsorption mechanism is probed by washing the adsorbed DNA with proteins, surfactants, and urea. Molecular dynamics simulations show that van der Waals forces are responsible for the tighter adsorption of PS DNA. Polycytosine (poly-C) DNA, in general, has a high affinity for the GO surface, and PS poly-C DNA can adsorb even stronger, making it an ideal anchoring sequence on GO. With this knowledge, noncovalent functionalization of GO with a diblock DNA is demonstrated, where a PS poly-C block is used to anchor on the surface. This conjugate achieves better hybridization than the PO DNA of the same sequence for hybridization with the complementary DNA.

Inverted Hydration Layers on Bio-Magnesium Surfaces in the Initial Degradation Stage and their Influence on Adsorption of Amino Acid Analogues: The Metadynamics Simulations.

Deeply exploring the interaction of biomolecules with magnesium in solution is essential to understand the formation of complex bio-magnesium interfaces accompanied with corrosion products. Using the accelerated metadynamics simulations, we have investigated the interactions of amino acid analogues on clean and hydroxylated Mg(0001) surfaces by identifying their free energy barriers and adsorption sites. We find that there are two hydration layers stacked on the clean Mg(0001) surfaces and the hydroxylated Mg(0001) surfaces, which mainly determine the free energy barriers and adsorbed configurations. Further studies reveal that the water molecules in double hydration layers present two opposite orientations, depending on the charge distribution of the substrate. Specifically, oxygen atoms of water concentrate in the center of double hydration layers for a clean Mg surface but transfer to the outside surface once the Mg substrate is degraded. The reversed hydration layers greatly reduce the binding affinities of positively charged and electroneutral analogues. Overall, our simulation findings provide new insights into the interaction mechanism of biomolecules on a bio-magnesium device in the implantation initial stage, which is noteworthy for revealing the magnesium degradation mechanism in vivo.

A DFT study of the adsorption of short peptides on Mg and Mg-based alloy surfaces.

Adsorption of short peptides, including three dipeptides: arginine-glycine (Arg-Gly), glycine-aspartic acid (Gly-Asp), arginine-aspartic acid (Arg-Asp), and one tripeptide arginine-glycine-aspartic acid (RGD), on the surfaces of Mg and Mg alloys (Mg-Zn, Mg-Y, and Mg-Nd), was studied using the first-principles calculations based on density functional theory (DFT), considering van der Waals (vdW) correction. The calculated adsorption energies (Eads) of short peptides on the clean Mg(0001) surface are in the range of -1.73 to -2.80 eV per dipeptide, and -3.24 eV for RGD. The short peptides prefer to bond to Mg atoms at the surface by the O and N anions in their functional groups. For the clean Mg(0001) surface, the Eads of the short peptides are exclusively dominated by the number of functional groups binding to the surface. However, for the surface of the Mg-Zn alloy (1% Zn), the adsorption of the peptides is clearly enhanced (by about 0.3 eV per peptide) due to the enhanced N-Mg bond and the electrostatic interactions between the doped Zn at the surface and the backbone chains of the peptides. Furthermore, the attractive interactions are increased with the increase of doped Zn contents (up to 3%). In contrast, for the surfaces of Mg-Y (1% Y) and Mg-Nd (1% Nd) alloys, the adsorption of the peptides is slightly weakened compared to that on the clean Mg(0001) surfaces. Our results provide useful guidance in understanding the interactions between peptides and the Mg-based biomedical alloy surfaces at the atomic scale in the biomimetic coating fields.

Investigation on the in vitro cytocompatibility of Mg-Zn-Y-Nd-Zr alloys as degradable orthopaedic implant materials.

Mg-Zn-Y-Nd-Zr alloy has been developed as a new type of biodegradable orthopaedic implant material by the authors' research group with its excellent mechanical properties and controllable degradation rate. In this study, the cytocompatibility of Mg-Zn-Y-Nd-Zr alloy was systematically evaluated through in vitro cell culture method. MTT assay was applied to evaluate the cytotoxicity of Mg-Zn-Y-Nd-Zr alloy and no toxic effect was observed on L929 and MC3T3-E1 cells followed the protocol of ISO 10993 standard. Considering the potential ion accumulation in the bony environment, this study further investigated the cytotoxic effect of accumulated metallic ions during the alloy degradation by extending the extract preparation time. When the extract preparation time was prolonged to 1440 h, the accumulated metallic ions leaded to severe cell apoptosis, of which the combined ion concentration was determined as 39.5-65.8 µM of Mg2+, 3.5-5.9 µM of Zn2+, 0.44-0.74 µM of Y3+, 0.3-0.52 µM of Nd3+ and 0.11-0.18 µM of Zr4+ for L929, and 65.8-92.2 µM of Mg2+, 5.9-8.3 µM of Zn2+, 0.74-1.04 µM of Y3+, 0.52-0.73 µM of Nd3+ and 0.18-0.25 µM of Zr4+ for MC3T3-E1 cells. Besides the cell viability assessment, high expression of ALP activity and calcified nodules implied that metal elements in Mg-Zn-Y-Nd-Zr alloys can promote the osteogenic differentiation. Hence, excellent cytocompatibility has equipped Mg-Zn-Y-Nd-Zr alloy as a promising candidate for orthopaedic implant application, which can remarkably guide the magnesium-based alloy design and provide scientific evidence for clinical practice in future.

Fucoidan/collagen composite coating on magnesium alloy for better corrosion resistance and pro-endothelialization potential.

Magnesium alloy stents (MAS) have broad application prospects in the treatment of cardiovascular diseases. However, poor corrosion resistance and biocompatibility greatly limit the clinical application of MAS. In this work, the coating consisting of MgF2 layer, polydopamine layer, fucoidan and collagen IV was constructed on Mg-Zn-Y-Nd (ZE21B) alloy to improve its corrosion resistance and pro-endothelialization potential. The fucoidan and collagen IV in the coating could obviously enhance the hemocompatibility and pro-endothelialization potential respectively. Compared with bare ZE21B alloy, the fucoidan/collagen composite coating modified ZE21B alloy possessed lower corrosion current density and better corrosion resistance. Moreover, the modified ZE21B alloy exhibited relatively low hemolysis rate, fibrinogen adsorption and platelet adhesion in the blood experiments, suggesting the improved hemocompatibility. Furthermore, the modified ZE21B alloy favorably supported the adhesion and proliferation of vascular endothelial cells (ECs) and effectively regulated the phenotype of smooth muscle cells (SMCs), thus improving the pro-endothelialization potential of vascular stent materials. The fucoidan/collagen composite coating can significantly improve the corrosion resistance and pro-endothelialization potential of ZE21B alloy, showing great potential in the development of degradable MAS.

Nucleus-targeted carbon dots as peroxidase nanozyme for photoacoustic imaging and phototherapy of tumor.

High-purity carbon dots (CDs) with a highly π-conjugated sp2-hybridized graphite structure were prepared by the pulse electrolysis method using the graphite plate as raw material. Photoacoustic signal together with photothermal effect was found in the CDs-dispersed suspensions under near-infrared (NIR) irradiation. For the suspension with the CDs concentration of 500 µg/mL, the photothermal conversion efficiency is high up 64.3% and the solution's temperature can be increased to 82.2 °C under NIR irradiation. Moreover, CDs can be effectively endocytosed by human hepatoma (HepG2) cells with a few hours, act as peroxidase nanozyme to decompose H2O2 and facilitate the production of reactive oxygen species. Under NIR irradiation, CDs exhibit an outstanding apoptosis-inducing effect on HepG2 cells by the photothermal effect. In addition, in vivo experiments show that CDs can be used in photoacoustic imaging (PAI) and guiding the tumor treatment. As a result, the nucleus-targeted CDs with an unique combination of PAI and photothermal effect have potential in cancer diagnosis and treatment.

Co-immobilization of natural marine polysaccharides and bioactive peptides on ZE21B magnesium alloy to enhance hemocompatibility and cytocompatibility.

Degradable magnesium alloy stents are considered to be ideal candidates to replace the traditional non-degradable stents for the treatment of cardiovascular diseases. However, bare magnesium alloy stents usually degrade too fast and show poor hemocompatibility and cytocompatibility, which seriously affects their clinical use. In this study, surface modification based on the MgF2 layer, polydopamine (PDA) coating, fucoidan and CAG peptides was performed on the Mg-Zn-Y-Nd (ZE21B) magnesium alloy with the purpose of improving its corrosion resistance, hemocompatibility and cytocompatibility for vascular stent application. After modification, the ZE21B alloy showed better corrosion resistance. Moreover, the lower hemolysis rate, platelet adhesion and activation, and fibrinogen adsorption and denaturation proved the improved hemocompatibility of modified ZE21B alloy in in vitro blood experiments. Furthermore, the co-immobilization of fucoidan and CAG peptides significantly promoted the adhesion, proliferation, migration and NO release of endothelial cells (ECs) on the modified ZE21B alloy, and meanwhile the modification with fucoidan and CAG peptides inhibited the adhesion and proliferation of smooth muscle cells (SMCs) and suppressed the expression of proinflammatory factors in the macrophages (MAs). The surface modification obviously enhanced the corrosion resistance, hemocompatibility and cytocompatibility of ZE21B alloy, and provided an effective strategy for the development of degradable vascular stents.

A Cu(â ¡)-eluting coating through silk fibroin film on ZE21B alloy designed for in situ endotheliazation biofunction.

In the cardiovascular field, coating containing copper used to catalyze NO (nitric oxide) production on non-degradable metal surfaces have shown unparalleled expected performance, but there are few studies on biodegradable metal surfaces. Magnesium-based biodegradable metals have been applied in cardiovascular field in large-scale because of their excellent properties. In this study, the coating of copper loaded in silk fibroin is fabricated on biodegradable ZE21B alloy. Importantly, the different content of copper is set to investigate the effects of on the degradation performance and cell behavior of magnesium alloy. Through electrochemical and immersion experiments, it is found that high content of copper will accelerate the corrosion of magnesium alloy. The reason is the spontaneous micro-batteries between copper and magnesium with the different standard electrode potentials, that is, the galvanic corrosion accelerates the corrosion of magnesium alloy. Moreover, the coating formed through silk fibroin by the right amount copper not only have a protective effect on the ZE21B alloy substrate, but also promotes the adhesion and proliferation of endothelial cells in blood vessel micro-environment. The production of NO catalyzed by copper ions makes this trend more significant, and inhibits the excessive proliferation of smooth muscle cells. These findings can provide guidance for the amount of copper in the coating on the surface of biodegradable magnesium alloy used for cardiovascular stent purpose.

Highly sensitive and thermal stable CO gas sensor based on SnO2 modified by SiO2.

Effects of surface chemical modification with SiO2 on the thermal stability and CO gas-sensing properties of SnO2 were investigated. The SiO2 on the SnO2 surface effectively inhibits the nanocrystal growth of SnO2. The average size of modified SnO2 sintered at 600 degrees C is 5.8 nm. The gas sensitivity to CO was found to be markedly enhanced by the surface chemical modification. The CO gas as low as 5 ppm can be effectively detected by the modified SnO2-based sensors. At the same time, the modified SnO2-based sensor has excellent selectivity to CO, fast response and recovery properties.

Long-circulating gambogic acid-loaded nanodiamond composite nanosystem with inhibition of cell migration for tumor therapy.

Herein, ultra dispersed and stably suspended nanodiamonds (NDs) were demonstrated to have a high load capacity, sustained release, and ability to serve as a biocompatible vehicle for delivery anticancer drugs. NDs with size of 50-100 nm exhibited good biocompatibility in normal human liver (L-02) cells. In particular, 50 nm ND not only promoted the noticeable proliferation of the L-02 cells but also can effectively inhibited the migration of human liver carcinoma (HepG2) cells. The gambogic acid-loaded nanodiamond (ND/GA) complex assembled by π-π stacking exhibits ultrasensitive and apparent suppression efficiency on the proliferation of HepG2 cells through high internalization and less efflux compared to free GA. More importantly, the ND/GA system can significantly increase the intracellular reactive oxygen species (ROS) levels in HepG2 cells and thus induce the cell apoptosis. The increase in intracellular ROS levels causes damage to the mitochondrial membrane potential (MMP) and activates cysteinyl aspartate specific proteinase 3 (Caspase-3) and cysteinyl aspartate specific proteinase 9 (Caspase-9), which leads to the occurrence of apoptosis. In vivo experiments also confirmed that the ND/GA complex has a much higher anti-tumor capability than free GA. Thus, the current ND/GA system is promising for cancer therapy.

The enhanced antibacterial effect of BNNS_Van@CS/MAO coating on Mg alloy for orthopedic applications.

The development of multifunctional Mg-based active implants with controllable degradation and antibacterial capabilities has become a hotspot in the research field of biodegradable metallic materials. To this end, a BN nanosheets (BNNS) _vancomycin (Van) @chitosan (CS) nanocomposite coating containing two antibacterial components (BNNS and Van) was prepared on Mg alloys via a micro-arc oxidation (MAO) pre-treatment combined with following electrodeposition. The related characterizations of the coating show that the composite coating has a high roughness, hydrophobicity and fair corrosion resistance. In vitro antibacterial experiments show that the BNNS_Van@CS/MAO composite coating have obvious inhibitory effect on the growth of both E. coli and S. aureus. The antibacterial effect of the BNNS_Van@CS/MAO composite coating was attributed to the synergistic effect of CS, BNNS and Van. This study provides a valuable surface modification strategy for developing multifunctional Mg-based implants with good corrosion resistance and antibacterial properties.

Surface modification of biodegradable magnesium alloy with poly (L-lactic acid) and sulfonated hyaluronic acid nanoparticles for cardiovascular application.

Magnesium (Mg) and its alloys have attracted extensive attention of researchers in the field of cardiovascular implants due to their good mechanical properties and biosafety. Constructing a multifunctional hybrid coating seems to be an effective strategy to address the insufficient endothelialization and poor corrosion resistance of Mg alloy vascular stents. In this study, a dense layer of magnesium fluoride (MgF2) was prepared on the surface of Mg alloy aiming at better corrosion resistance; Thereafter, sulfonated hyaluronic acid (S-HA) was made into small sized nanoparticles (NP) which were deposited on the MgF2 surface by self-assembly method, followed with poly-L-lactic acid (PLLA) coating preparation by one-step pulling method. The blood and cell tests showed that the composite coating had good blood compatibility, pro-endothelial, anti-hyperplasia and anti-inflammatory functions. Compared to current clinical PLLA@ Rapamycin coating, our PLLA/NP@S-HA coating showed better functions of promoting endothelial cells growth. These results strongly furnished a promising and feasible strategy for the surface modification of Mg-based degradable cardiovascular stents.

Degradation behavior of ZE21C magnesium alloy suture anchors and their effect on ligament-bone junction repair.

Current materials comprising suture anchors used to reconstruct ligament-bone junctions still have limitation in biocompatibility, degradability or mechanical properties. Magnesium alloys are potential bone implant materials, and Mg2+ has been shown to promote ligament-bone healing. Here, we used Mg-2 wt.% Zn-0.5 wt.% Y-1 wt.% Nd-0.5 wt.% Zr (ZE21C) alloy and Ti6Al4V (TC4) alloy to prepare suture anchors to reconstruct the patellar ligament-tibia in SD rats. We studied the degradation behavior of the ZE21C suture anchor via in vitro and in vivo experiments and assessed its reparative effect on the ligament-bone junction. In vitro, the ZE21C suture anchor degraded gradually, and calcium and phosphorus products accumulated on its surface during degradation. In vivo, the ZE21C suture anchor could maintain its mechanical integrity within 12 weeks of implantation in rats. The tail of the ZE21C suture anchor in high stress concentration degraded rapidly during the early implantation stage (0-4weeks), while bone healing accelerated the degradation of the anchor head in the late implantation stage (4-12weeks). Radiological, histological, and biomechanical assays indicated that the ZE21C suture anchor promoted bone healing above the suture anchor and fibrocartilaginous interface regeneration in the ligament-bone junction, leading to better biomechanical strength than the TC4 group. Hence, this study provides a basis for further research on the clinical application of degradable magnesium alloy suture anchors.

Design of single-phased magnesium alloys with typically high solubility rare earth elements for biomedical applications: Concept and proof.

Rare earth elements (REEs) have been long applied in magnesium alloys, among which the mischmetal-containing WE43 alloy has already got the CE mark approval for clinical application. A considerable amount of REEs (7 wt%) is needed in that multi-phased alloy to achieve a good combination of mechanical strength and corrosion resistance. However, the high complex RE addition accompanied with multiple second phases may bring the concern of biological hazards. Single-phased Mg-RE alloys with simpler compositions were proposed to improve the overall performance, i.e., "Simpler alloy, better performance". The single-phased microstructure can be successfully obtained with typical high-solubility REEs (Ho, Er or Lu) through traditional smelting, casting and extrusion in a wide compositional range. A good corrosion resistance with a macroscopically uniform corrosion mode was guaranteed by the homogeneously single-phased microstructure. The bimodal-grained structure with plenty of sub-grain microstructures allow us to minimize the RE addition to <1 wt%, without losing mechanical properties. The single-phased Mg-RE alloys show comparable mechanical properties to the clinically-proven Mg-based implants. They exhibited similar in-vitro and in-vivo performances (without local or systematic toxicity in SD-rats) compared to a high purity magnesium. In addition, metal elements in our single-phased alloys can be gradually excreted through the urinary system and digestive system, showing no consistent accumulation of RE in main organs, i.e., less burden on organs. The novel concept in this study focuses on the simplification of Mg-RE based alloys for biomedical purpose, and other biodegradable metals with single-phased microstructures are expected to be explored.

Sustained delivery of gambogic acid from mesoporous rod-structure hydroxyapatite for efficient in vitro cancer therapy.

Inspired by the critical role of nanocarrier in biomaterials modification, we synthesized a mesoporous rod-structure hydroxyapatite (MR-HAp) nanoparticles for boosting gambogic acid (GA) bioavailability in cells and improving the tumor therapy. As expected, the GA loading ratio of MR-HAp was up to about 96.97% and GA-loaded MR-HAp (MR-HAp/GA) demonstrates a sustained release performance. Furthermore, a substantial improvement was observed in inhibiting the cell proliferation and inducing the apoptosis of HeLa cells, as the cell viability was decreased to 89.6% and the apoptosis was increased to 49.2% when the cells treated with MR-HAp/GA at a GA concentration of 1 µg/mL for 72 h. The remarkable inhibition effect of cell proliferation and the enhanced inducing apoptosis are attributed to the increasing intracellular reactive oxygen species level and reduced mitochondrial membrane potential. This result provides a promising and facile approach for highly efficient tumor treatment.