Cobalt ferrite/semiconducting single-walled carbon nanotubes based field-effect transistor for determination of carbamate pesticides.

Carbaryl and carbofuran are the carbamate pesticides which have been widely used worldwide to control insects in crops and house. If the pesticides entered in to the food products and drinking water, they could cause serious health effects in humans. Therefore, the development of a rapid, simple, sensitive and selective analytical device for on-site detection of carbamates is crucial to evaluate food and environmental samples. Recently, semiconducting single-walled carbon nanotube-based field effect transistors (s-SWCNT/FETs) have shown several advantages such as high carrier mobility, good on/off ratio, quasi ballistic electron transport, label-free detection and real-time response. Herein, cobalt ferrite (CFO) nanoparticles decorated s-SWCNTs have been prepared and used to bridge the source and drain electrodes. As-prepared CFO/s-SWCNT/FET had been used for the non-enzymatic detection of carbaryl and carbofuran. When used as a sensing platform, the CFO/s-SWCNT hybrid film exhibited high sensitivity, and selectivity with a wide linear range of detection from 10 to 100 fMand the lowest limit of detections for carbaryl (0.11 fM) and carbofuran (0.07 fM) were estimated. This sensor was also used to detect carbaryl in tomato and cabbage samples, which confirmed its practical acceptance. Such performance may be attributed to the oxidation of carbamates by potent catalytic activity of CFO, which led to the changes in the charge transfer reaction on the s-SWCNTs/FET conduction channel. This work presents a novel CFO/s-SWCNT based sensing system which could be used to quantify pesticide residues in food samples.

Hydrothermal synthesis of V2O5/TiO2 decorated graphitic carbon nitride nanocomposite for biomolecule oxidation inhibition and dye degradation applications.

Oxides of vanadium, titanium and graphitic carbon nitride (g-C3N4) are well known for their catalytic activities. In order to achieve synergic catalytic effects, a novel nanocomposite (NC) i.e. V2O5/TiO2/g-C3N4 has been synthesized by a very simple, ecofriendly and nonhazardous hydrothermal method. The fabricated NC was characterized employing UV-Visible, FTIR, SEM, and XRD techniques. UV-Visible and FTIR analysis indicated the formation of the nanocomposite and XRD analysis confirmed the association of V2O5 and TiO2 with g-C3N4 in nanocomposite. SEM study indicated the hetero-structure of NC having size ranging from 50 to 80 nm and it was found having hexagonal crystallite structure. The synthesized nanocomposite exhibited excellent scavenging of free radicals DPPH● (91%) and ABTS●+ (64%) that are responsible for the oxidation of biomolecules. Therefore, NC can be claimed having biomolecule oxidation protective potential. In addition, photocatalytic ability for the degradation of methylene blue (MB) and methyl orange (MO) was also achieved up to 94% and 89% respectively. The synthesized novel nanocomposite exhibited excellent potential to remove free radicals and dyes from aqueous medium which can be further used for the environmental remediation.

Coupling of carboxymethyl starch with 2-carboxyethyl acrylate: A new sorbent for the wastewater remediation of methylene blue.

Textile and printing industries play a vital role in the economy of any country. But the effluents of these industries, which contain toxic Methylene Blue (MB) dye when mixed with fresh water, make it unfit for human health and aquatic life. For the removal of MB, different adsorbents were used, but they were expensive, non-biodegradable or less effective. In this research, novel carboxymethyl starch grafted poly 2-carboxyethyl acrylate (CM-St-g-P2CEtA) was synthesized by reacting carboxymethyl starch with 2-carboxyethyl acrylate. The reaction followed a free radical polymerization mechanism. The structure and properties of CM-St-g-P2CEtA were investigated by advanced analytical techniques. The CM-St-g-P2CEtA was employed for the remediation of Methylene Blue (MB) dye from wastewater. The removal percentage (%R) of MB was checked under different parameters, like different pH levels, different initial concentrations of dye, different adsorbent doses, and different contact times. The results obtained during the experiment were subjected to different adsorption and kinetic models. In the kinetic investigation, the experimental results were best represented by the pseudo-second-order kinetic model due to its high R2 value of 0.999. Similarly, with a regression coefficient (R2) value of 0.947, the Langmuir adsorption isotherm was best represented by the experimental results. The Langmuir adsorption model showed that MB dye was adsorbed on the surface of CM-St-g-P2CEtA in a monolayer pattern. The pseudo 2nd order kinetic model suggested that the adsorption process favored chemisorption mechanism. The CM-St-g-P2CEtA showed maximum percentage removal efficiency (%R) of 99.3% for MB dye.

Biomass derived nitrogen functionalized carbon nanodots for nanomolar determination of levofloxacin in pharmaceutical and water samples.

Binder-free and efficient electrochemical sensing of levofloxacin (LF) was successfully developed based on the nitrogen-doped carbon nanodots (NCNDs). The NCNDs were synthesized by hydrothermal carbonation (180°C for 12 h), and the heteroatom was embedded in aqueous solution of ammonia (NH3). Spectral and microscopic characteristization techniques were used to analyze the topological, crystallinity, and chemical binding behavior of synthesized biomass functional material. HR-TEM image revealed a uniform spherical dot (2.96 nm), and superior quantum yield efficiency (0.42 Φ). The NCNDs was drop coated on a glassy carbon electrode (GCE) and electrochemical sensing of LF was performed by cyclic voltammetry (CV), differential pulse voltammetry (DPV), and amperometric i-t curve in phosphate-buffered saline (PBS; pH = 7.0). The NCNDs modified electrode showed a sharp oxidation peak at +0.95 V (vs. Ag/AgCl) with a four-fold higher current response than the bare GC electrode. The NCNDs/GCE surface not only increases the current response, but has lower detection potential, and facilitates electron transfer reaction. Under optimized working parameters, the NCNDs/GCE showed wide linear concentrations range from 200 nM to 2.8 mM and a low detection limit (LOD) of 48.26 nM (S/N = 3). The electrode modified with NCNDs has high electrochemical sensing stability (RSD = 1.284 ± 0.05% over 5 days), and superior reproducibility (RSD = 1.682 ± 0.06% (n = 3)). Finally, the NCNDs modified GC electrode was successfully applied to quantify the concentration of LF in drug and river water samples with acceptable recovery percentages of 96.60-99.20% and 97.20-99.00% (n=3), respectively.

Photocatalytic Degradation Studies of Organic Dyes over Novel Cu/Ni Loaded Reduced Graphene Oxide Hybrid Nanocomposite: Adsorption, Kinetics and Thermodynamic Studies.

Nowadays, for environmental remediation, photocatalytic process involving graphene-based semiconductors is considered a very promising oxidation process for water treatment. In the present study, nanocomposite (Cu/Ni/rGO) has been synthesized by Dypsis lutescens leaf extract. Characterization of the sample was carried out by UV-visible spectroscopy, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis, Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Different parameters like contact time, nanocatalyst amount, dye concentration, effect of temperature. and pH factor were optimized to examine the maximum removal efficiency for dyes rhodamine B and alizarine R with and without visible light source. In both cases, i.e., with or without light, maximum removal was observed at 20 mg of nanocatalyst for 5 ppm concentration of both dyes at 45 °C temperature and pH 10 for rhodamine B and pH 4 for alizarine R, respectively with a 20 min contact time. Maximum removal of dyes 93% rhodamine B and 91% alizarine R were observed under a tungsten lamp as compared to without a tungsten lamp, i.e., 78% of RhB and 75% of AR from mixture solution of these dyes. To assess the rate of reaction, spontaneity, and nature of reaction thermodynamics, kinetics and adsorption isotherms were studied. Thermodynamic values indicated that both dyes depicted endothermic and spontaneous degradation processes. Isotherm data fitted best to a Freundlich isotherm, while results of kinetic studies of both dyes followed the pseudo 2nd order kinetic equation. In the end, scavenging radical studies concluded that hydroxyl radicals were the main active specie involved in the photocatalytic degradation process, and regeneration experiments resulted that Cu/Ni/rGO nanocomposites were re-utilized for about four times.

Benzothiophene Adsorptive Desulfurization onto trihexYl(tetradecyl)phosphonium Dicyanamide Ionic-Liquid-Modified Renewable Carbon: Kinetic, Equilibrium and UV Spectroscopy Investigations.

The negative environmental and industrial impacts of the presence of sulfur compounds such as benzothiophene in fuels have led to a greater interest in desulfurization research. In this work, carbon from palm waste sources was modified with trihexYl(tetradecyl)phosphonium dicyanamide-ionic liquid and characterized by SEM, EDS, XRD and FTIR to assess surface properties. Then, the prepared carbon and carbon modified with ionic liquid were evaluated for the adsorption of benzothiophene by investigating the effects of time. The equilibrium occurred after 120 min, recording adsorption capacities of 192 and 238 mg/g for carbon and carbon modified with ionic liquid, respectively. The effect of the adsorbent dose on the adsorption of benzothiophene was evaluated, indicating that the maximum adsorption capacities were obtained using a dose of 1 g/L for both carbon and carbon modified with ionic liquid. The kinetic investigation for the adsorption of benzothiophene onto carbon and carbon modified with ionic liquid indicated that the second-order kinetic model is well fitted with the adsorption data rather than the first-order kinetic model. The equilibrium investigations for the adsorption of benzothiophene onto carbon and carbon modified with ionic liquid with Langmuir and Freundlich isotherm models reveals that the Freundlich model is the most suitable for describing the adsorption process, suggesting a multilayer adsorption mechanism. The desulfurization process showed a high impact on environmental safety due to the possibility of regenerating and reusing the prepared adsorbents with promising results up to five cycles.

Synergetic effect of Sn doped ZnO nanoparticles synthesized via ultrasonication technique and its photocatalytic and antibacterial activity.

The current work reports the photocatalytic and antibacterial performance of tin (Sn) doped zinc oxide (ZnO) nanoparticles synthesized via ultrasonic aided co-precipitation technique. The increase of Sn concentration decreased the lattice parameter and increased the crystallite size without changing the ZnO structure. The hexagonal shaped particles and sheets obtained for 3% and 5% Sn substituted ZnO, respectively. The increase of dopant concentration reduced the reflectance and optical band gap energy of Sn doped ZnO. The vibrational band present at 1443 cm-1 confirmed the successful bond formation of Sn-O-Zn. The 5% Sn doped ZnO nanoparticles exhibited greater dye elimination rate of methylene blue compared to 3% Sn. The antibacterial activity of Sn doped ZnO showed the higher zone of inhibition about 14 mm against different pathogens. The 5% Sn doped ZnO photocatalyst improve the transfer rate of photo excite carrier and decrease the rate of recombination which greatly influence on the photocatalytic and antibacterial performance.

An efficient and magnetically recoverable g-C3N4/ZnS/CoFe2O4 nanocomposite for sustainable photodegradation of organic dye under UV-visible light illumination.

Effective improvement of an easily recoverable photocatalyst is equally vital to its photocatalytic performance from a practical application view. The magnetically recoverable process is one of the easiest ways, provided the photocatalyst is magnetically strong enough to respond to an external magnetic field. Herein, we prepared graphitic carbon nitride nanosheet (g-C3N4), and ZnS quantum dots (QDs) supported ferromagnetic CoFe2O4 nanoparticles (NPs) as the gC3N4/ZnS/CoFe2O4 nanohybrid photocatalyst by a wet-impregnation method. The loading of CoFe2O4 NPs in the g-C3N4/ZnS nanohybrid resulted in extended visible light absorption. The ferromagnetic g-C3N4/ZnS/CoFe2O4 nanohybrid exhibited better visible-light-active photocatalytic performance (97.11%) against methylene blue (MB) dye, and it was easily separable from the aqueous solution by an external bar magnet. The g-C3N4/ZnS/CoFe2O4 nanohybrid displayed excellent photostability and reusability after five consecutive cycles. The favourable band alignment and availability of a large number of active sites affected the better charge separation and enhanced photocatalytic response. The role of active species involved in the degradation of MB dye during photocatalyst by g-C3N4/ZnS/CoFe2O4 nanohybrid was also investigated. Overall, this study provides a facile method for design eco-friendly and promising g-C3N4/ZnS/CoFe2O4 nanohybrid photocatalyst as applicable in the eco-friendly dye degradation process.

Graphene oxide@Ce-doped TiO2 nanoparticles as electrocatalyst materials for voltammetric detection of hazardous methyl parathion.

A sensitive voltammetric sensor has been developed for hazardous methyl parathion detection (MP) using graphene oxide@Ce-doped TiO2 nanoparticle (GO@Ce-doped TiO2 NP) electrocatalyst. The GO@Ce-doped TiO2 NPs were prepared through the sol-gel method and characterized by various physicochemical and electrochemical techniques. The GO@Ce-doped TiO2 NP-modified glassy carbon electrode (GCE) addresses excellent electrocatalytic activity towards MP detection for environmental safety and protection. The developed strategy of GO@Ce-doped TiO2 NPs at GCE surfaces for MP detection achieved excellent sensitivity (2.359 µA µM-1 cm-2) and a low detection limit (LOD) 0.0016 µM with a wide linear range (0.002 to 48.327 µM). Moreover, the fabricated sensor shows high selectivity and long-term stability towards MP detection; this significant electrode further paves the way for real-time monitoring of environmental quantitative samples with satisfying recoveries.

Equilibrium and Kinetic Study of Anionic and Cationic Pollutants Remediation by Limestone-Chitosan-Alginate Nanocomposite from Aqueous Solution.

In this work, low-cost and readily available limestone was converted into nanolimestone chitosan and mixed with alginate powder and precipitate to form a triple nanocomposite, namely limestone-chitosan-alginate (NLS/Cs/Alg.), which was used as an adsorbent for the removal of brilliant green (BG) and Congo red (CR) dyes in aqueous solutions. The adsorption studies were conducted under varying parameters, including contact time, temperature, concentration, and pH. The NLS/Cs/Alg. was characterized by SEM, FTIR, BET, and TEM techniques. The SEM images revealed that the NLS/Cs/Alg. surface structure had interconnected pores, which could easily trap the pollutants. The BET analysis established the surface area to be 20.45 m2/g. The recorded maximum experimental adsorption capacities were 2250 and 2020 mg/g for CR and BG, respectively. The adsorption processes had a good fit to the kinetic pseudo second order, which suggests that the removal mechanism was controlled by physical adsorption. The CR and BG equilibrium data had a good fit for the Freundlich isotherm, suggesting that adsorption processes occurred on the heterogeneous surface with a multilayer formation on the NLS/Cs/Alg. at equilibrium. The enthalpy change (ΔH0) was 37.7 KJ mol-1 for CR and 8.71 KJ mol-1 for BG, while the entropy change (ΔS0) was 89.1 J K-1 mol-1 for CR and 79.1 J K-1 mol-1 BG, indicating that the adsorption process was endothermic and spontaneous in nature.

Production of Terretonin N and Butyrolactone I by Thermophilic Aspergillus terreus TM8 Promoted Apoptosis and Cell Death in Human Prostate and Ovarian Cancer Cells.

The anticancer activity of terretonin N (1) and butyrolactone I (2), obtained from the thermophilic fungus Aspergillus terreus TM8, was intensively studied against prostate adenocarcinoma (PC-3) and ovary adenocarcinoma (SKOV3) human cell lines. According to this study, both compounds showed potent cytotoxicity towards ovarian adenocarcinoma cells (SKOV3) with IC50 1.2 and 0.6 µg/mL, respectively. With respect to metastatic prostate cells (PC-3), the two compounds 1 and 2 showed a significantly promising cytotoxicity effect with IC50 of 7.4 and 4.5 µg/mL, respectively. The tested fungal metabolites showed higher rates of early and late apoptosis with little or no necrotic apoptotic pathway in all treated prostate adenocarcinoma (PC-3) and ovary adenocarcinoma (SKOV3) human cell lines, respectively. The results reported in this study confirmed the promising biological properties of terretonin N (1) and butyrolactone I (2) as anticancer agents via the induction of cellular apoptosis. However, further studies are needed to elucidate the molecular mechanism by which cellular apoptosis is induced in cancer cells.

Regulatory Role of Nano-Curcumin against Tartrazine-Induced Oxidative Stress, Apoptosis-Related Genes Expression, and Genotoxicity in Rats.

The present study evaluates the regulatory effect of Nano-Curcumin (Nano-CUR) against tartrazine (TZ)-induced injuries on apoptosis-related gene expression (i.e., p53, CASP-3 and CASP-9), antioxidant status, and DNA damages in bone marrow in treated rats. Male rats were arbitrarily separated into five groups, and each group was comprised of 10 rats each. The 1st group served as control (G1). The 2nd group ingested 7.5 mg TZ/kg. b.w. (body weight). The 3rd group ingested Nano-CUR 1 g/kg b.w. The 4th and 5th groups were respectively administered with (1 g Nano-CUR + 7.5 mg TZ/kg. b.w.) and (2 g Nano-CUR + 7.5 mg TZ/kg. b.w.). At the end of the experiment, blood samples, livers, and kidneys were collected. Livers and kidneys were homogenized and used for the analysis of reduced glutathione, malonaldhyde, total antioxidant capacity, lipid peroxide antioxidant enzyme activities, apoptosis-related gene expression, and genotoxicity by comit test. The ingestion of TZ for 50 days resulted in significant decreases in body, and kidney weights in rats and a relative increase in the liver weight compared to control. In contrast, the ingestion of Nano-CUR with TZ remarkably upgraded the body weight and relative liver weight compared to the normal range in the control. Aditionally, TZ ingestion in rats increased the oxidative stress biomarkers lipid peroxide (LPO) and malonaldehyde (MDA) significantly, whereas it decreased the reduced glutathione (GSH) levels and total antioxidant capacity (TAC). Similarly, the levels of glutathione peroxidase (GPx), superoxide dismutase (SOD), and catalase (CAT) significantly deteriorated in response to TZ ingestion. Moreover, the results revealed a remarkable up-regulation in the level of expression for the three examined genes, including p53, CASP-3, and CASP-9 in TZ-ingested rats compared to the control. On the other hand, the comet assay result indicates that the ingestion of TZ induced DNA damage in bone marrow. Notably, the administration of Nano-CUR protected the kidney and liver of TZ-ingested rats as evidenced by a significant elevation in all antioxidant activities of tested enzymes (i.e, SOD, GPx, and CAT), vital recovery in GSH and TAC levels, and a statistical decrease in LPO and MDA compared to TZ-ingested rats. Interestingly, the ingestion of rats with TZ modulates the observed up-regulation in the level of expression for the chosen genes, indicating the interfering role in the signaling transduction process of TZ-mediated poisoning. The results indicate that the administration of Nano-CUR may protect against TZ-induced DNA damage in bone marrow. According to the results, Nano-CUR exerted a potential protective effect against oxidative stress, DNA damage, and the up-regulation of apoptosis-related genes induced by TZ ingested to rats.

Deep Eutectic Solvent-Based Microextraction of Lead(II) Traces from Water and Aqueous Extracts before FAAS Measurements.

Microextraction procedures for the separation of Pb(II) from water and food samples extracts were developed. A deep eutectic solvent composed of α-benzoin oxime and iron(III) chloride dissolved in phenol was applied as a phase separator support. In addition, this deep eutectic mixture worked as an efficient extractor of Pb(II). The developed microextraction process showed a high ability to tolerate the common coexisting ions in the real samples. The optimum conditions for quantitative recoveries of Pb(II) from aqueous extracts were at pH 2.0, conducted by adding 150 µL from the deep eutectic solvent. The quantitative recoveries were obtained with various initial sample volumes up to 30 mL. Limits of detection and limits of quantification of 0.008 and 0.025 µg L-1 were achieved with a relative standard deviation (RSD%) of 2.9, which indicates the accuracy and sensitivity of the developed procedure. Recoveries from the reference materials, including TMDA 64.2, TMDA 53.3, and NCSDC-73349, were 100%, 97%, and 102%, respectively. Real samples, such as tap, lake, and river water, as well as food samples, including salted peanuts, chickpeas, roasted yellow corn, pistachios, and almonds, were successfully applied for Pb(II) analysis by atomic absorption spectroscopy (AAS) after applying the developed deep eutectic solvent-based microextraction procedures.

Bioremediation of Explosive TNT by Trichoderma viride.

Nitroaromatic and nitroamine compounds such as 2,4,6-trinitrotoluene (TNT) are teratogenic, cytotoxic, and may cause cellular mutations in humans, animals, plants, and microorganisms. Microbial-based bioremediation technologies have been shown to offer several advantages against the cellular toxicity of nitro-organic compounds. Thus, the current study was designed to evaluate the ability of Trichoderma viride to degrade nitrogenous explosives, such as TNT, by microbiological assay and Gas chromatography-mass spectrometry (GC-MS) analysis. In this study, T. viride fungus was shown to have the ability to decompose, and TNT explosives were used at doses of 50 and 100 ppm on the respective growth media as a nitrogenous source needed for normal growth. The GC/MS analysis confirmed the biodegradable efficiency of TNT, whereas the initial retention peak of the TNT compounds disappeared, and another two peaks appeared at the retention times of 9.31 and 13.14 min. Mass spectrum analysis identified 5-(hydroxymethyl)-2-furancarboxaldehyde with the molecular formula C6H6O3 and a molecular weight of 126 g·mol-1 as the major compound, and 4-propyl benzaldehyde with a formula of C10H12O and a molecular weight of 148 g mol-1 as the minor compound, both resulting from the biodegradation of TNT by T. viride. In conclusion, T. viride could be used in microbial-based bioremediation technologies as a biological agent to eradicate the toxicity of the TNT explosive. In addition, future molecular-based studies should be conducted to clearly identify the enzymes and the corresponding genes that give T. viride the ability to degrade and remediate TNT explosives. This could help in the eradication of soils contaminated with explosives or other toxic biohazards.

Phosphonium-based Ionic Liquid Modified Activated Carbon from Mixed Recyclable Waste for Mercury(II) Uptake.

The contamination of water surfaces by mercury is a dangerous environmental problem due to its toxicity, which leads kidney damage. Activated carbon from mixed recyclable waste modified by phosphonium-based ionic liquid (IL-ACMRW) was therefore prepared and evaluated for Hg(II) remediation. The activated carbon used in this study was prepared from mixed waste, including cardboard, papers and palm wastes as cheap raw materials. The mixed Recyclable Waste Activated Carbon was combined with trihexyl(tetradecyl)phosphonium Bis2,4,4-(trimethylpentyl)phosphinate (Cyphos® IL 104) ionic liquid to form an adsorbent with organic-inorganic content, in order to improve the Hg(II) uptake from aqueous solutions. FTIR confirms the presence of P, C=O and OH after this modification. The adsorption process was investigated and the evaluated results showed that the capacity was 124 mg/g at pH 4, with a contact time of 90 min, an adsorbent dose of 0.4 g/L, and a Hg(II) concentration of 50 mg/L. This Hg(II) adsorption capacity is superior than that reported in the literature for modified multiwall carbon nanotubes. The adsorption of Hg(II) on the modified activated carbon from mixed recyclable waste was found to follow the pseudo second-order kinetics model. Isotherms of adsorption were analyzed via Freundlich and Langmuir models. The results indicated that Freundlich is the best model to describe the process, suggesting multilayer adsorption.

One-Step Carbon Coating and Polyacrylamide Functionalization of Fe3O4 Nanoparticles for Enhancing Magnetic Adsorptive-Remediation of Heavy Metals.

Magnetic nanoparticles are used in adsorptive removal of heavy metals from polluted wastewater. However, their poor stability in an acidic medium necessitates their protection with a coating layer. Coating magnetic nanoparticles with carbon showed proper protection but the heavy metal removal efficiency was slightly weak. However, to boost the removal efficiencies of surface functionalization, polyacrylamide was applied to carbon-coated Fe3O4 nanoparticles. In this paper, to facilitate the synthesis process, one-step carbon coating and polyacrylamide functionalization were conducted using the hydrothermal technique with the aim of enhancing the adsorptive removal capacity of Fe3O4 nanoparticles towards some heavy metals such as Cu(II), Ni(II), Co(II), and Cd(II). The results showed that the one-step process succeeded in developing a carbon coating layer and polyacrylamide functionality on Fe3O4 nanoparticles. The stability of the magnetic Fe3O4 nanoparticles as an adsorbent in an acidic medium was improved due to its resistance to the dissolution that was gained during carbon coating and surface functionalization with polyacrylamide. The adsorptive removal process was investigated in relation to various parameters such as pH, time of contact, metal ion concentrations, adsorbent dose, and temperature. The polyacrylamide functionalized Fe3O4 showed an improvement in the adsorption capacity as compared with the unfunctionalized one. The conditions for superior adsorption were obtained at pH 6; time of contact, 90 min; metal solution concentration, 200 mg/L; adsorbent dose, 0.3 g/L. The modeling of the adsorption data was found to be consistent with the pseudo-second-order kinetic model, which suggests a fast adsorption process. However, the equilibrium data modeling was consistent with both the Langmuir and Freundlich isotherms. Furthermore, the thermodynamic parameters of the adsorptive removal process, including ΔG°, ΔH°, and ΔS°, indicated a spontaneous and endothermic sorption process. The developed adsorbent can be utilized further for industrial-based applications.

Dispersive liquid-liquid microextraction of lead(II) as 5-(4-dimethylaminobenzylidene) rhodanine chelates from food and water samples.

A dispersive liquid-liquid microextraction procedure for lead(II) as its 5-(4-dimethylaminobenzylidene) rhodanine complex has been established prior to its microsampling flame atomic absorption spectrometric determination. The influences of various analytical parameters including pH, solvent type and volume, dispersive solvent type and volume, 5-(4-dimethylaminobenzylidene) rhodanine amount, salt effect, and centrifugation time and speed were investigated. The effects of certain alkali, alkaline earth, and transition metal ions on the quantitative extraction of lead(II) were also studied. Quantitative recoveries were obtained at pH 6. The enrichment factor was calculated as 125. The detection limit for lead is 1.1 µg/L. The accuracy of the method was tested with the additions recovery test and analysis of the standard reference materials (SPS-WW2 waste water, NIST SRM 1515 apple leaves, and TMDA-51.3 fortified water). Applications of the present procedure were tested by analyzing water and food samples.

Fabrication of NIPMAM based polymer microgel network assisted rhodium nanoparticles for reductive degradation of toxic azo dyes.

The aim of this study was to prepare poly-N-isopropylmethacrylamide-co-acrylic acid-acrylamide [p-(NIPMAM-co-AA-AAm)] via precipitation polymerization in an aqueous medium. Rhodium nanoparticles were formed in the microgel network by an in-situ reduction technique with the addition of sodium borohydride as a reducing agent. Pure p-(NIPMAM-co-AA-AAm) and hybrid microgels [Rh-(p-NIPMAM-co-AA-AAm)] microgels were examined by using UV-Visible, FTIR (Fourier Transform Infrared), SEM (Scanning Electron Microscopy), TEM (Transmission Electron Microscopy), DLS (Dynamic Light Scattering) and XRD (X-Ray Diffraction) techniques. The catalytic activities of the hybrid microgel [Rh-(p-NIPMAM-co-AA-AAm)] for the degradation of azo dyes such as alizarin yellow (AY), congo red (CR), and methyl orange (MO) were compared and the mechanism of the catalytic action by this system was examined. Various parameters including the catalyst amount and dye concentration influenced the catalytic decomposition of azo dyes. In order to maximize the reaction conditions for the dye's quick and efficient decomposition, the reaction process was monitored by spectroscopic analysis. The rate constants for reductive degradation of azo dyes were measured under various conditions. When kapp values were compared for dyes, it was found that [Rh-(p-NIPMAM-co-AA-AAm)] hybrid microgels showed superior activity for the degradation of MO dyes compared to the reductive degradation of CR and AY.

Valorization of algal biomass to synthesize heterogeneous gC3N4-Biochar photocatalyst for the treatment of industrial wastewater using photocatalysis-persulfate oxidation process.

Textile wastewater, heavily contaminated with organic dyes, is generating severe problems to environment and human health. The implementation of gC3N4 with biochar (gC3N4-BC) for the treatment of textile wastewater is less effective due to the limited adsorption capacity and slower degradation kinetics. To tackle these problems, peroxydisulfate (PDS) is integrated with gC3N4-BC photocatalyst to enhance the process efficiency and kinetics. The synthesized gC3N4-BC-5 composite shows higher separation of charge carriers, light absorbance, and lower energy bandgap (2.62 eV). The results of photocatalytic degradation and rate constant are enhanced up to 99.9 % and 0.041 min-1 using gC3N4-BC-5 with PDS as compared to without PDS (96.8 % and 0.028 min-1, respectively). The radicals (SO4-•,O2-•, and OH•) are responsible to improve the degradation process efficiency and kinetics. The reusability of optimized sample indicates that gC3N4-BC-5 is stable and effective up to five cycles. The gC3N4-BC-5 composite attains highest adsorption (70.9 %) when compared to BC (62.3 %) and pure gC3N4 (27.1 %). The well-fitted models of adsorption (Pseudo-Second-Order and Freundlich) confirm the favorable, chemical, and multilayered adsorption process. The coupling of gC3N4-BC-5 with PDS is effective, efficient, and stable process to enhance the kinetics and degradation of textile wastewater.