Self-Abrading Servo Electrode Helmet for Electrical Impedance Tomography.

Electrical Impedance Tomography (EIT) is a medical imaging technique which has the potential to reduce time to treatment in acute stroke by rapidly differentiating between ischaemic and haemorrhagic stroke. The potential of these methods has been demonstrated in simulation and phantoms, it has not yet successfully translated to clinical studies, due to high sensitivity to errors in scalp electrode mislocation and poor electrode-skin contact. To overcome these limitations, a novel electrode helmet was designed, bearing 32 independently controlled self-abrading electrodes. The contact impedance was reduced through rotation on an abrasive electrode on the scalp using a combined impedance, rotation and position feedback loop. Potentiometers within each unit measure the electrode tip displacement within 0.1 mm from the rigid helmet body. Characterisation experiments on a large-scale test rig demonstrated that approximately 20 kPa applied pressure and 5 rotations was necessary to achieve the target 5 kΩ contact impedance at 20 Hz. This performance was then replicated in a simplified self-contained unit where spring loaded electrodes are rotated by servo motors. Finally, a 32-channel helmet and controller which sequentially minimised contact impedance and simultaneously located each electrode was built which reduced the electrode application and localisation time to less than five minutes. The results demonstrated the potential of this approach to rapidly apply electrodes in an acute setting, removing a significant barrier for imaging acute stroke with EIT.

Mechanistic insights from targeted molecular profiling of repolarization alternans in the intact human heart.

AIMS: Action potential duration (APD) alternans is an established precursor or arrhythmia and sudden cardiac death. Important differences in fundamental electrophysiological properties relevant to arrhythmia exist between experimental models and the diseased in vivo human heart. To investigate mechanisms of APD alternans using a novel approach combining intact heart and cellular cardiac electrophysiology in human in vivo. METHODS AND RESULTS: We developed a novel approach combining intact heart electrophysiological mapping during cardiac surgery with rapid on-site data analysis to guide myocardial biopsies for laboratory analysis, thereby linking repolarization dynamics observed at the organ level with underlying ion channel expression. Alternans-susceptible and alternans-resistant regions were identified by an incremental pacing protocol. Biopsies from these sites (n = 13) demonstrated greater RNA expression in Calsequestrin (CSQN) and Ryanodine (RyR) and ion channels underlying IK1 and Ito at alternans-susceptible sites. Electrical restitution properties (n = 7) showed no difference between alternans-susceptible and resistant sites, whereas spatial gradients of repolarization were greater in alternans-susceptible than in alternans-resistant sites (P = 0.001). The degree of histological fibrosis between alternans-susceptible and resistant sites was equivalent. Mathematical modelling of these changes indicated that both CSQN and RyR up-regulation are key determinants of APD alternans. CONCLUSION: Combined intact heart and cellular electrophysiology show that regions of myocardium in the in vivo human heart exhibiting APD alternans are associated with greater expression of CSQN and RyR and show no difference in restitution properties compared to non-alternans regions. In silico modelling identifies up-regulation and interaction of CSQN with RyR as a major mechanism underlying APD alternans.

In Vivo and In Silico Investigation Into Mechanisms of Frequency Dependence of Repolarization Alternans in Human Ventricular Cardiomyocytes.

RATIONALE: Repolarization alternans (RA) are associated with arrhythmogenesis. Animal studies have revealed potential mechanisms, but human-focused studies are needed. RA generation and frequency dependence may be determined by cell-to-cell variability in protein expression, which is regulated by genetic and external factors. OBJECTIVE: To characterize in vivo RA in human and to investigate in silico using human models, the ionic mechanisms underlying the frequency-dependent differences in RA behavior identified in vivo. METHODS AND RESULTS: In vivo electrograms were acquired at 240 sites covering the epicardium of 41 patients at 6 cycle lengths (600-350 ms). In silico investigations were conducted using a population of biophysically detailed human models incorporating variability in protein expression and calibrated using in vivo recordings. Both in silico and in vivo, 2 types of RA were identified, with Fork- and Eye-type restitution curves, based on RA persistence or disappearance, respectively, at fast pacing rates. In silico simulations show that RA are strongly correlated with fluctuations in sarcoplasmic reticulum calcium, because of strong release and weak reuptake. Large L-type calcium current conductance is responsible for RA disappearance at fast frequencies in Eye-type (30% larger in Eye-type versus Fork-type; P<0.01), because of sarcoplasmic reticulum Ca(2+) ATPase pump potentiation caused by frequency-induced increase in intracellular calcium. Large Na(+)/Ca(2+) exchanger current is the main driver in translating Ca(2+) fluctuations into RA. CONCLUSIONS: In human in vivo and in silico, 2 types of RA are identified, with RA persistence/disappearance as frequency increases. In silico, L-type calcium current and Na(+)/Ca(2+) exchanger current determine RA human cell-to-cell differences through intracellular and sarcoplasmic reticulum calcium regulation.

Creation and Initial Validation of the International Dysphagia Diet Standardisation Initiative Functional Diet Scale.

OBJECTIVE: To assess consensual validity, interrater reliability, and criterion validity of the International Dysphagia Diet Standardisation Initiative Functional Diet Scale, a new functional outcome scale intended to capture the severity of oropharyngeal dysphagia, as represented by the degree of diet texture restriction recommended for the patient. DESIGN: Participants assigned International Dysphagia Diet Standardisation Initiative Functional Diet Scale scores to 16 clinical cases. Consensual validity was measured against reference scores determined by an author reference panel. Interrater reliability was measured overall and across quartile subsets of the dataset. Criterion validity was evaluated versus Functional Oral Intake Scale (FOIS) scores assigned by survey respondents to the same case scenarios. Feedback was requested regarding ease and likelihood of use. SETTING: Web-based survey. PARTICIPANTS: Respondents (N=170) from 29 countries. INTERVENTIONS: Not applicable. MAIN OUTCOME MEASURES: Consensual validity (percent agreement and Kendall τ), criterion validity (Spearman rank correlation), and interrater reliability (Kendall concordance and intraclass coefficients). RESULTS: The International Dysphagia Diet Standardisation Initiative Functional Diet Scale showed strong consensual validity, criterion validity, and interrater reliability. Scenarios involving liquid-only diets, transition from nonoral feeding, or trial diet advances in therapy showed the poorest consensus, indicating a need for clear instructions on how to score these situations. The International Dysphagia Diet Standardisation Initiative Functional Diet Scale showed greater sensitivity than the FOIS to specific changes in diet. Most (>70%) respondents indicated enthusiasm for implementing the International Dysphagia Diet Standardisation Initiative Functional Diet Scale. CONCLUSIONS: This initial validation study suggests that the International Dysphagia Diet Standardisation Initiative Functional Diet Scale has strong consensual and criterion validity and can be used reliably by clinicians to capture diet texture restriction and progression in people with dysphagia.

Development of International Terminology and Definitions for Texture-Modified Foods and Thickened Fluids Used in Dysphagia Management: The IDDSI Framework.

Dysphagia is estimated to affect ~8% of the world's population (~590 million people). Texture-modified foods and thickened drinks are commonly used to reduce the risks of choking and aspiration. The International Dysphagia Diet Standardisation Initiative (IDDSI) was founded with the goal of developing globally standardized terminology and definitions for texture-modified foods and liquids applicable to individuals with dysphagia of all ages, in all care settings, and all cultures. A multi-professional volunteer committee developed a dysphagia diet framework through systematic review and stakeholder consultation. First, a survey of existing national terminologies and current practice was conducted, receiving 2050 responses from 33 countries. Respondents included individuals with dysphagia; their caregivers; organizations supporting individuals with dysphagia; healthcare professionals; food service providers; researchers; and industry. The results revealed common use of 3-4 levels of food texture (54 different names) and ≥3 levels of liquid thickness (27 different names). Substantial support was expressed for international standardization. Next, a systematic review regarding the impact of food texture and liquid consistency on swallowing was completed. A meeting was then convened to review data from previous phases, and develop a draft framework. A further international stakeholder survey sought feedback to guide framework refinement; 3190 responses were received from 57 countries. The IDDSI Framework (released in November, 2015) involves a continuum of 8 levels (0-7) identified by numbers, text labels, color codes, definitions, and measurement methods. The IDDSI Framework is recommended for implementation throughout the world.

Measurement bias in activation-recovery intervals from unipolar electrograms.

The activation-recovery interval (ARI) calculated from unipolar electrograms is regularly used as a convenient surrogate measure of local cardiac action potential durations (APD). This method enables important research bridging between computational studies and in vitro and in vivo human studies. The Wyatt method is well established as a theoretically sound method for calculating ARIs; however, some studies have observed that it is prone to a bias error in measurement when applied to positive T waves. This article demonstrates that recent theoretical and computational studies supporting the use of the Wyatt method are likely to have underestimated the extent of this bias in many practical experimental recording scenarios. This work addresses these situations and explains the measurement bias by adapting existing theoretical expressions of the electrogram to represent practical experimental recording configurations. A new analytic expression for the electrogram's local component is derived, which identifies the source of measurement bias for positive T waves. A computer implementation of the new analytic model confirms our hypothesis that the bias is systematically dependent on the electrode configuration. These results provide an aid to electrogram interpretation in general, and this work's outcomes are used to make recommendations on how to minimize measurement error.

Effect of autonomic blocking agents on the respiratory-related oscillations of ventricular action potential duration in humans.

Ventricular action potential duration (APD) is an important component of many physiological functions including arrhythmogenesis. APD oscillations have recently been reported in humans at the respiratory frequency. This study investigates the contribution of the autonomic nervous system to these oscillations. In 10 patients undergoing treatment for supraventricular arrhythmias, activation recovery intervals (ARI; a conventional surrogate for APD) were measured from multiple left and right ventricular (RV) endocardial sites, together with femoral artery pressure. Respiration was voluntarily regulated and heart rate clamped by RV pacing. Sympathetic and parasympathetic blockade was achieved using intravenous metoprolol and atropine, respectively. Metroprolol reduced the rate of pressure development (maximal change in pressure over time): 1,271 (± 646) vs. 930 (± 433) mmHg/s; P < 0.01. Systolic blood pressure (SBP) showed a trend to decrease after metoprolol, 133 (± 21) vs. 128 (± 25) mmHg; P = 0.06, and atropine infusion, 122 (± 26) mmHg; P < 0.05. ARI and SBP exhibited significant cyclical variations (P < 0.05) with respiration in all subjects with peak-to-peak amplitudes ranging between 0.7 and 17.0 mmHg and 1 and 16 ms, respectively. Infusion of metoprolol reduced the mean peak-to-peak amplitude [ARI, 6.2 (± 1.4) vs. 4.4 (± 1.0) ms, P = 0.008; SBP, 8.4 (± 1.6) vs. 6.2 (± 2.0) mmHg, P = 0.002]. The addition of atropine had no significant effect. ARI, SBP, and respiration showed significant coupling (P < 0.05) at the breathing frequency in all subjects. Directed coherence from respiration to ARI was high and reduced after metoprolol infusion [0.70 (± 0.17) vs. 0.50 (± 0.23); P < 0.05]. These results suggest a role of respiration in modulating the electrophysiology of ventricular myocardium in humans, which is partly, but not totally, mediated by ß-adrenergic mechanisms.

The influence of food texture and liquid consistency modification on swallowing physiology and function: a systematic review.

Texture modification has become one of the most common forms of intervention for dysphagia, and is widely considered important for promoting safe and efficient swallowing. However, to date, there is no single convention with respect to the terminology used to describe levels of liquid thickening or food texture modification for clinical use. As a first step toward building a common taxonomy, a systematic review was undertaken to identify empirical evidence describing the impact of liquid consistency and food texture on swallowing behavior. A multi-engine search yielded 10,147 non-duplicate articles, which were screened for relevance. A team of ten international researchers collaborated to conduct full-text reviews for 488 of these articles, which met the study inclusion criteria. Of these, 36 articles were found to contain specific information comparing oral processing or swallowing behaviors for at least two liquid consistencies or food textures. Qualitative synthesis revealed two key trends with respect to the impact of thickening liquids on swallowing: thicker liquids reduce the risk of penetration-aspiration, but also increase the risk of post-swallow residue in the pharynx. The literature was insufficient to support the delineation of specific viscosity boundaries or other quantifiable material properties related to these clinical outcomes. With respect to food texture, the literature pointed to properties of hardness, cohesiveness, and slipperiness as being relevant both for physiological behaviors and bolus flow patterns. The literature suggests a need to classify food and fluid behavior in the context of the physiological processes involved in oral transport and flow initiation.

Erratum to: The Influence of Food Texture and Liquid Consistency Modification on Swallowing Physiology and Function: A Systematic Review.

Erratum to: Dysphagia DOI 10.1007/s00455-014-9578-x. In the original version of this article, Fig. 1 was published incorrectly. The corrected figure is given below.

Validation of the IDDSI funnel for liquid flow testing.

In 2017, the International Dysphagia Diet Standardisation Initiative (IDDSI) introduced the IDDSI flow test which enables patients, clinicians, caregivers, food service professionals and researchers to classify liquid thickness into five levels based on the volume of liquid remaining in a standard 10 mL slip tip syringe after 10 s of flow under gravity. Within a few months of publishing the IDDSI flow test instructions, several barriers emerged: (1) the preferred model of syringe (BD 303134) was not equally accessible around the world, causing some users to perform flow tests with alternate models of syringe; (2) differences in syringe geometry across models led to variations in IDDSI flow test results; and (3) the need to use a second syringe for sample loading added complexity and cost to end users. To address these barriers, IDDSI designed the IDDSI funnel, a novel device, which combines the geometry of the BD 303134 syringe with a kitchen funnel to facilitate easy loading of liquid samples without need for a second syringe. In this report, we compare the IDDSI flow test results across two devices: syringe BD 303134 and IDDSI funnel. IDDSI level classifications were in complete agreement with the syringe reference test results in 67/73 (92%) of the test fluids and temperature conditions with mean difference of residual liquid across devices of 0.2 (2% full scale). These results demonstrate excellent correspondence between the two devices.

Molecular mass dependence of point-to-set correlation length scale in polymers.

We use a recently proposed metric, termed the point-to-set correlation functions, to probe the molecular weight dependence of the relevant static length scales in glass-forming oligomeric chain liquids of 4, 5, 8, and 10 repeat units. In agreement with the results for simple, monatomic fluids, we find that static length scales of the oligomers increase monotonically when the temperature is lowered towards the glass transition temperature of the fluid. More interestingly, the static length scale increases with increasing chain length. Within the bounds of error in our simulations, the static length scale appears to scale as the radius of gyration of the oligomer, but with a prefactor, which is much larger than unity and which grows with the temperature. The preceding behavior contrasts with the length scales extracted from the radial distribution function of the oligomer system, which is practically independent of the chain length.

Effects of saliva on starch-thickened drinks with acidic and neutral pH.

Powdered maize starch thickeners are used to modify drink consistency in the clinical management of dysphagia. Amylase is a digestive enzyme found in saliva which breaks down starch. This action is dependent on pH, which varies in practice depending on the particular drink. This study measured the effects of human saliva on the viscosity of drinks thickened with a widely used starch-based thickener. Experiments simulated a possible clinical scenario whereby saliva enters a cup and contaminates a drink. Citric acid (E330) was added to water to produce a controlled range of pH from 3.0 to 7.0, and several commercially available drinks with naturally low pH were investigated. When saliva was added to thickened water, viscosity was reduced to less than 1% of its original value after 10-15 min. However, lowering pH systematically slowed the reduction in viscosity attributable to saliva. At pH 3.5 and below, saliva was found to have no significant effect on viscosity. The pH of drinks in this study ranged from 2.6 for Coca Cola to 6.2 for black coffee. Again, low pH slowed the effect of saliva. For many popular drinks, having pH of 3.6 or less, viscosity was not significantly affected by the addition of saliva.

The effect of saliva on the viscosity of thickened drinks.

Powdered thickeners are used to modify drink consistency in the clinical management of dysphagia. These thickeners are composed of primarily modified maize starch; some varieties also incorporate powdered gums. Amylase is a digestive enzyme found in saliva that initiates the breakdown of starch. To determine the significance of this process in dysphagia management, we measured the effects of human saliva on the viscosity of thickened drinks. Two thickeners were studied: one comprising modified maize starch alone and one that included additional gums. These were added to drinks with neutral and acidic pH: water and orange juice. Two clinical scenarios were simulated: (1) the effect of saliva on fluid as it is swallowed and (2) the effect when saliva enters a cup and contaminates a drink. Saliva was found to reduce the viscosity of water thickened with maize starch in both scenarios: (1) 90% reduction after 10 s and (2) almost 100% reduction in viscosity after 20 min. The thickener composed of gums and maize starch showed a significant reduction but retained a level of thickening. In contrast, thickened orange juice (pH 3.8) was not observed to undergo any measurable reduction in viscosity under the action of saliva.

Modernising Orodispersible Film Characterisation to Improve Palatability and Acceptability Using a Toolbox of Techniques.

Orodispersible films (ODFs) have been widely used in paediatric, geriatric and dysphagic patients due to ease of administration and precise and flexible dose adjustments. ODF fabrication has seen significant advancements with the move towards more technologically advanced production methods. The acceptability of ODFs is dependent upon film composition and process of formation, which affects disintegration, taste, texture and mouthfeel. There is currently a lack of testing to accurately assess ODFs for these important acceptability sensory perceptions. This study produced four ODFs formed of polyvinyl alcohol and sodium carboxymethylcellulose using 3D printing. These were assessed using three in vitro methods: Petri dish and oral cavity model (OCM) methods for disintegration and bio-tribology for disintegration and oral perception. Increasing polymer molecular weight (MW) exponentially increased disintegration time in the Petri dish and OCM methods. Higher MW films adhered to the OCM upper palate. Bio-tribology analysis showed that films of higher MW disintegrated quickest and had lower coefficient of friction, perhaps demonstrating good oral perception but also stickiness, with higher viscosity. These techniques, part of a toolbox, may enable formulators to design, test and reformulate ODFs that both disintegrate rapidly and may be better perceived when consumed, improving overall treatment acceptability.

Variation of the apparent viscosity of thickened drinks.

BACKGROUND: In dysphagia care, thickening powders are widely added to drinks to slow their flow speed by increasing their viscosity. Current practice relies on subjective evaluation of viscosity using verbal descriptors. Several brands of thickener are available, with differences in constituent ingredients and instructions for use. Some thickened fluids have previously been shown to exhibit time-varying non-Newtonian flow behaviour, which may complicate attempts at subjective viscosity judgement. AIMS: The aims were to quantify the apparent viscosity over time produced by thickeners having a range of constituent ingredients, and to relate the results to clinical practice. METHODS & PROCEDURES: A comparative evaluation of currently available thickener products, including two which have recently been reformulated, was performed. Their subjective compliance to the National Descriptors standards was assessed, and their apparent viscosity was measured using a rheometer at shear rates representative of situations from slow tipping in a beaker (0.1 s⁻¹) to a fast swallow (100 s⁻¹). Testing was performed repeatedly up to 3 h from mixing. OUTCOMES & RESULTS: When mixed with water, it was found that most products compared well with subjective National Descriptors at three thickness levels. The fluids were all highly non-Newtonian; their apparent viscosity was strongly dependent on the rate of testing, typically decreasing by a factor of almost 100 as shear rate increased. All fluids showed some change in viscosity with time from mixing; this varied between products from -34% to 37% in the tests. This magnitude was less than the difference between thickness levels specified by the National Descriptors. CONCLUSIONS & IMPLICATIONS: The apparent viscosity of thickened fluids depends strongly on the shear rate at which it is examined. This inherent behaviour is likely to hinder subjective evaluation of viscosity. If quantitative measures of viscosity are required (for example, for standardization purposes), they must therefore be qualified with information of the test conditions.

Assessing the ability of substrate mapping techniques to guide ventricular tachycardia ablation using computational modelling.

BACKGROUND: Identification of targets for ablation of post-infarction ventricular tachycardias (VTs) remains challenging, often requiring arrhythmia induction to delineate the reentrant circuit. This carries a risk for the patient and may not be feasible. Substrate mapping has emerged as a safer strategy to uncover arrhythmogenic regions. However, VT recurrence remains common. GOAL: To use computer simulations to assess the ability of different substrate mapping approaches to identify VT exit sites. METHODS: A 3D computational model of the porcine post-infarction heart was constructed to simulate VT and paced rhythm. Electroanatomical maps were constructed based on endocardial electrogram features and the reentry vulnerability index (RVI - a metric combining activation (AT) and repolarization timings to identify tissue susceptibility to reentry). Since scar transmurality in our model was not homogeneous, parameters derived from all signals (including dense scar regions) were used in the analysis. Potential ablation targets obtained from each electroanatomical map during pacing were compared to the exit site detected during VT mapping. RESULTS: Simulation data showed that voltage cut-offs applied to bipolar electrograms could delineate the scar, but not the VT circuit. Electrogram fractionation had the highest correlation with scar transmurality. The RVI identified regions closest to VT exit site but was outperformed by AT gradients combined with voltage cut-offs. The performance of all metrics was affected by pacing location. CONCLUSIONS: Substrate mapping could provide information about the infarct, but the directional dependency on activation should be considered. Activation-repolarization metrics have utility in safely identifying VT targets, even with non-transmural scars.

The impact of modification techniques on the rheological properties of dysphagia foods and liquids.

Modifying food and the textures of food has been done for decades within the food science and technology field. More recently, modifying the texture of foods has been used to manage swallowing disabilities (dysphagia). Swallowing disabilities are often associated with dehydration and malnutrition, thus nutritional intervention has formed part of serving texture-modified diets. The question remains whether these modification techniques are viable for individuals with swallowing disabilities living in majority world countries. This study used two modification methods on a widely used specialized nutritious food (SNF) to determine whether it may be modified and used in dysphagia management. The techniques had to be ergonomic and economically appropriate for individuals with swallowing disabilities living in majority world countries. The International Dysphagia Diet Standardization Initiative's (IDDSI) standards were used to determine whether the texturally modified SNF is safe for swallowing. Rheological measurements were performed to determine apparent viscosity and structure recovery of each sample. The effects of two modification techniques, aeration and particle separation, on the rheological properties of the SNF were also measured and analyzed. It was determined that both milk and water could be used with this SNF to create a dysphagia diet, but only under certain conditions. The overall results indicated that heating the samples increased the apparent viscosity and exacerbated lumping. Room temperature samples had less lumps and could be classified to the desired levels of the IDDSI (Level 2 and Level 4). Using a whisk to aerate the samples reduced lumps significantly and using a sieve to separate particles of liquid samples eliminated lumps. This study provides new data on how texture modification techniques and the IDDSI framework could be adapted to individuals living in majority world countries. By using modification techniques that are ergonomic and economically viable and an SNF with longevity, this study could be useful in guiding future training of nursing staff and caregivers of individuals living in poverty or resource-constrained communities. This study also adds to the data on the rheological properties of dysphagia foods, although this study did not make use of commercial thickeners generally used in the modification of diets.

How Do Orodispersible Tablets Behave in an In Vitro Oral Cavity Model: A Pilot Study.

Orodispersible tablets (ODTs) offer rapid disintegration of the dosage form when placed on the tongue, which leads to fast release of the active pharmaceutical ingredient. Despite increased use in diverse patient populations, there have been numerous challenges associated with ODTs. One such concern is the lack of standardised assessment of disintegration behaviour. In the European Pharmacopoeia, 'orodispersibles' are defined as such if disintegration time is faster than 3 min. Common in vitro measurement methods only provide single time point data and have limited physiological accuracy. To determine more bio-predictive disintegration kinetics, a bench-top in vitro oral cavity model (OCM) was modified and piloted to assess disintegration of three ODTs of differing hardness. All ODTs disintegrated similarly within the OCM-surface breakdown/swelling, initial 'wash away' and final 'wash away'. The distinct advantage presented within this pilot study using the OCM is the opportunity to ascertain disintegration behaviour profiles of ODTs by evaluating changes in the observable area during simulated oral processing. The model could be implemented as a decision-support tool during the early stages of the drug design process to improve acceptability and further understand ODT disintegration behaviour.

Evaluation of the reentry vulnerability index to predict ventricular tachycardia circuits using high-density contact mapping.

BACKGROUND: Identifying arrhythmogenic sites to improve ventricular tachycardia (VT) ablation outcomes remains unresolved. The reentry vulnerability index (RVI) combines activation and repolarization timings to identify sites critical for reentrant arrhythmia initiation without inducing VT. OBJECTIVE: The purpose of this study was to provide the first assessment of RVI's capability to identify VT sites of origin using high-density contact mapping and comparison with other activation-repolarization markers of functional substrate. METHODS: Eighteen VT ablation patients (16 male; 72% ischemic) were studied. Unipolar electrograms were recorded during ventricular pacing and analyzed offline. Activation time (AT), activation-recovery interval (ARI), and repolarization time (RT) were measured. Vulnerability to reentry was mapped based on RVI and spatial distribution of AT, ARI, and RT. The distance from sites identified as vulnerable to reentry to the VT site of origin was measured, with distances <10 mm and >20 mm indicating accurate and inaccurate localization, respectively. RESULTS: The origins of 18 VTs (6 entrainment, 12 pace-mapping) were identified. RVI maps included 1012 (408-2098) (median, 1st-3rd quartiles) points per patient. RVI accurately localized 72.2% VT sites of origin, with median distance of 5.1 (3.2-10.1) mm. Inaccurate localization was significantly less frequent for RVI than AT (5.6% vs 33.3%; odds ratio 0.12; P = .035). Compared to RVI, distance to VT sites of origin was significantly larger for sites showing prolonged RT and ARI and were nonsignificantly larger for sites showing highest AT and ARI gradients. CONCLUSION: RVI identifies vulnerable regions closest to VT sites of origin. Activation-repolarization metrics may improve VT substrate delineation and inform novel ablation strategies.