RESUMEN
This study aims to improve the quality of fuel with high calorific value namely Sfuel - a commercial high-quality refuse-derived fuel (RDF) from hazardous waste via modifying the process design and operating parameters of thermal conversion process. The study analyses key parameters of RDF quality, such as calorific value and heavy metal content, before and after process modifications based on the combination of experimental and simulation using Aspen Plus. In this study, the temperature and pressure of the simulation system are varied from 100 to 700 °C and from 1 to 5 bar, respectively. Findings indicate that there are a total of eleven heavy metals and 179 volatile compounds in the "Sfuels". The quality of the targeted product is greatly improved by the metal evaporation at high temperatures and pressures. However, the calorific value of RDF significantly decreases at 700 °C due to a large amount of the carbon content being evaporated. Although the carbon content at high temperatures is significantly lost, the heat from the vapour stream reactor outlet, which is reused to preheat the nitrogen gas stream supplied to the system, reduces energy consumption while improving the thermal conversion efficiency of the system. Besides, low pressure along with high temperature are not the optimal conditions for quality Sfuels improvement by thermal conversion. Results also indicate that electric heating is more economically efficient than natural gas heating.
Asunto(s)
Metales Pesados , Metales Pesados/análisis , Eliminación de Residuos/métodos , Simulación por Computador , Residuos Peligrosos/análisis , CalorRESUMEN
In this work, a simple sol-gel approach was used for the preparation of cyanopropyl (CNPr) functionalized silica nanoparticles (SiO2-CNPr) that tetraethoxysilane (TEOS) and cyanopropyltriethoxysilane (CNPrTEOS) used as precursors. This as-prepared SiO2-CNPr nanoparticle sorbent was first characterized using FESEM, EDX, FTIR, TGA, and BET techniques. Then, the SiO2-CNPr nanoparticle was applied as a new SPE sorbent for determining trace levels of OPPs in environmental water samples. To enhance the simultaneous extraction of non-polar or/and polar OPPs and to obtain the most efficient sorbent, several sol-gel synthesis parameters were studied. In addition, the effect of several effective parameters on SPE performance was investigated toward simultaneous extraction of non-polar or/and polar OPPs. Moreover, the figures of merit such as precision, linearity, LOQ, LOD, and recovery were evaluated for the sorbent. Finally, the designed SiO2-CNPr SPE was used to determine OPPs in real water samples, and its extraction performance was compared to commercial cartridges based on cyanopropyl.
Asunto(s)
Plaguicidas , Plaguicidas/análisis , Dióxido de Silicio , Compuestos Organofosforados , Extracción en Fase Sólida/métodos , AguaRESUMEN
Semiconductor metal oxide with TiO2 nanoparticles removes hazardous compounds from environmental samples. TiO2 nanoparticles have shown potential as an efficient photocatalyst by being employed as a nano-catalyst for the breakdown of organic contaminants in wastewater samples. To separate substances from contaminated samples, combined UV and visible light irradiation has been used. Sol-gel synthesis was used to produce a copper chromite-titanium nanocomposite, which was then evaluated using analytical methods, such as XRD, BET, DRS-UV, and FT-IR. Using visible light, the photocatalytic activity of a nanocomposite made of CuCr2O4 and TiO2 was investigated for its role in the breakdown of malachite green. The effects of several parameters, including pH change, anions presence, contact time, catalyst amount, concentration variation, and the kinetics of photocatalytic degradation were investigated. The magnitude of transition energy calculated using UV-DRS spectra was found to be 3.1 eV for CuCr2O4-TiO2 nanocomposite. Maximum degradation was observed at pH 7.0. The surface area and pore volume of the co-doped samples of Cr2O4 - TiO2 obtained from BET were found to be 6.1213 m2/g and 0.045063 cm3/g respectively. The average particle size of the catalyst of the nano-catalysts calculated from XRD was found to be 8 nm for TiO2 and 66 nm for TiO2-CuCrO4. The peaks obtained in FTIR between the range of 900-500 cm-1 were due to the presence of an aromatic compound. The binding mechanism of a dye molecule to the surface of CuCr2O4-TiO2 nanocomposite was analysed using quantum chemical calculations with the self-consistent reaction field technique employing integral equation formalism for the polarized continuum method and the UFF atomic radii set.
Asunto(s)
Nanocompuestos , Nanopartículas , Titanio/química , Espectroscopía Infrarroja por Transformada de Fourier , Luz , Agua , Nanocompuestos/química , Colorantes/química , CatálisisRESUMEN
Biomass co-firing with coal can be adopted in the electricity sector to promote greenhouse gas reduction, renewable energy production, and resource efficiency improvement toward environmental sustainability. This realization, however, requires effective management of supply chain issues, such as the collection of biomass feedstock, the transportation of biomass, and the localization of biomass processing plants to deliver the co-firing scales needed. This work addresses these issues by providing a techno-economic assessment conducted in a spatially-explicit manner to investigate the opportunity for scaling up the co-firing deployment at the national scale. The modeling approach is applied to the case of Malaysia's coal and palm oil biomass industries. The number of cases involving the impact of energy decarbonization targets, economic policy instrument, and supply chain cost parameter variations on the co-firing scales deployed are assessed. The findings show that densified biomass feedstock can substitute significant shares of coal capacities to deliver up to 29 MtCO2/year of carbon dioxide reduction. Nevertheless, this would cause a surge in the electricity system cost by up to 2 billion USD/year due to the substitution of up to 40% of the coal plant capacities. In facilitating the maximal deployment of co-firing at the national scale, more than 100 solid biofuel production plants would need to be built to support a maximum of 41 TWh/year of co-firing capacity. Actions to minimize the specific cost elements of the biomass co-firing supply chain are thus needed in the near term to increase the effectiveness of economic policy instrument to promote co-firing and reduce environmental emissions.
Asunto(s)
Carbón Mineral , Centrales Eléctricas , Biocombustibles , Biomasa , Aceite de PalmaRESUMEN
Polyhydroxyalkanoate (PHA) is a type of polyesters produced in the form of accumulated intracellular granules by many microorganisms. It is viewed as an environmentally friendly bioproduct due to its biodegradability and biocompatibility. The production of the PHA using oil substrates such as waste oil and plant oil, has gained considerable attention due to the high product yield and lower substrate cost. Nevertheless, the PHA fermentation using oil substrate is complicated due to the heterogenous fatty acid composition, varied bio-accessibility and possible inhibitory effect on the bacterial culture. This review presents the current state-of-the-art of PHA production from oil-based substrates. This paper firstly discusses the technical details, such as the choice of bacteria strain and fermentation conditions, characteristic of the oil substrate as well as the PHA composition and application. Finally, the paper discusses the challenges and prospects for up-scaling towards a cleaner and effective bioprocess. From the literature review, depending on the cell culture and the type of PHA produced, the oil platform can have a PHA yield of 0.2-0.8 g PHA/g oil substrate, with PHA content mostly from 40 to 90% of the cell dry weight. There is an on-going search for more effective oil-utilising PHA producers and lower cost substrate for effective PHA production. The final application of the PHA polymer influences the treatment needed during downstream processing and its economic performance. PHA with different compositions exhibits varied decomposition behaviour under different conditions, requiring further insight towards its management towards a sustainable circular economy.
Asunto(s)
Polihidroxialcanoatos , Bacterias , Ácidos Grasos , Fermentación , PoliésteresRESUMEN
Energy is widely used in industry for heating and cooling, with natural gas (NG) being the largest primary energy source in Malaysia, closely followed by coal. Renewable energy, such as biogas upgrading to biomethane, could cut the use of fossil fuels by supplementing NG usage due to their similar physicochemical and thermochemical characteristics. Biogas production plants in Malaysia are more commonly seen in waste-to-energy scenarios, with the technology anaerobic digestion, and their deployment is supported via feed-in tariffs (FiT) for power generation. Other potential applications such as the conversion of biogas into biomethane, injection into the natural gas grid or transportation through a virtual pipeline may still need further technical development. This paper presents spatial techno economic optimisation modelling using BeWhere to determine decentralised biomethane production plants using feedstock from multiple sources of biogas, including palm oil mill effluent (POME), food waste, cattle manure and chicken manure. This model considered potential configurations and sizes of the biomethane plants, the transportation of biomethane using a virtual pipeline (at 250 psig) and demand in one of the states in Malaysia, namely Johor. It was found that two to four biomethane plants with capacities ranging between 125 and 700â¯m3/h were located in densely populated areas or heavier industrial consumers when the carbon tax was implemented at 167.71 EUR/tCO2 (800 MYR/tCO2). Sensitivity analysis suggested that biomethane production increases with the increasing country renewable energy share target to beyond 2080â¯MW. It is recommended that specific policy regulations and Feed-in Tariff (FiT) mechanisms are used to expand the biomethane market share in the country.
Asunto(s)
Biocombustibles , Gas Natural , Animales , Bovinos , Malasia , Estiércol , Metano , Aceite de PalmaRESUMEN
Rapid population growth and urbanisation have generated large amount of municipal solid waste (MSW) in many cities. Up to 40-60% of Malaysia's MSW is reported to be food waste where such waste is highly putrescible and can cause bad odour and public health issue if its disposal is delayed. In this study, the implementation of community composting in a village within Iskandar Malaysia is presented as a case study to showcase effective MSW management and mitigation of GHG emission. The selected village, Felda Taib Andak (FTA), is located within a palm oil plantation and a crude palm oil processing mill. This project showcases a community-composting prototype to compost food and oil palm wastes into high quality compost. The objective of this article is to highlight the economic and environment impacts of a community-based composting project to the key stakeholders in the community, including residents, oil palm plantation owners and palm oil mill operators by comparing three different scenarios, through a life cycle approach, in terms of the greenhouse gas emission and cost benefit analysis. First scenario is the baseline case, where all the domestic waste is sent to landfill site. In the second scenario, a small-scale centralised composting project was implemented. In the third scenario, the data obtained from Scenario 2 was used to do a projection on the GHG emission and costing analysis for a pilot-scale centralised composting plant. The study showed a reduction potential of 71.64% on GHG emission through the diversion of food waste from landfill, compost utilisation and significant revenue from the compost sale in Scenario 3. This thus provided better insight into the feasibility and desirability in implementing a pilot-scale centralised composting plant for a sub-urban community in Malaysia to achieve a low carbon and self-sustainable society, in terms of environment and economic aspects.
Asunto(s)
Carbono , Eliminación de Residuos , Ciudades , Efecto Invernadero , MalasiaRESUMEN
Achieving net zero emissions to ensure a sustainable future has become increasingly urgent in light of climate change. The palm oil industry in Malaysia plays a significant role in the country's economy but has faced criticism for its environmental impact, particularly in terms of sustainability and greenhouse gas emissions. While the government has implemented policies and initiatives to promote sustainable palm oil production and reduce emissions, there remains a need for a comprehensive and integrated mitigation strategy to help make an informed decision to improve the performance. To address the limitations of the current framework, this study proposes an Integrated Mitigation Strategy Model which incorporates established frameworks of Palm Oil Mill Carbon Accounting (POMCFA) and Sustainability Index (POMSI). This model has been developed based on the superstructure approach, considering a set of mitigation options to improve weak indicators identified through assessments. The selection of these options is informed by a theoretical review of existing literature on factor changes and their impact on emissions reduction. The model is further validated through case studies, ensuring its robustness and reliability. Based on the case study, it reveals that palm oil mill effluent, diesel consumption, and water consumption contribute the most to carbon dioxide equivalent emissions. In terms of sustainability scoring, the environmental aspect obtains the lowest scores compared to social and economic aspects. Weaknesses identified include dust concentration, palm oil mill effluent, and boiler emissions. Using the heuristics of factor changes equation, the mitigation model suggests implementing high-technology boilers as the optimal solution for these weaknesses. With the theoretical and empirical support behind the choice of variables, our model provides a valuable tool for decision-making in achieving net-zero emissions and sustainable palm oil production.
RESUMEN
The present study examines the effect of medical staff's turning movements on particle concentration in the surgical zone and settlement on the patient under single large diffuser (SLD) ventilation. A computational domain representing the operating room (OR) was constructed using computer-aided design (CAD) software. The airflow and particle models were validated against the published data before conducting the case studies. The airflow in the OR was simulated using an RNG k-ε turbulence model, while the dispersion of the particles was simulated using a discrete phase model based on the Lagrangian approach. A user-defined function (UDF) code was written and compiled in the simulation software to describe the medical staff member's turning movements. In this study, three cases were examined: baseline, SLD 1, and SLD 2, with the air supply areas of 4.3 m2, 5.7 m2, and 15.9 m2, respectively. Results show that SLD ventilations in an OR can reduce the number of dispersed particles in the surgical zone. The particles that settled on the patient were reduced by 41% and 39% when using the SLD 1 and SLD 2 ventilations, respectively. The use of the larger air supply area of SLD 2 ventilation in the present study does not significantly reduce the particles that settle on a patient. Likewise, the use of SLD 2 ventilation may increase operating and maintenance costs.