Near Room Temperature Production of Segregated Network Composites of Carbon Nanotubes and Regolith as Multifunctional, Extra-Terrestrial Building Materials.

Constructing a semi-permanent base on the moon or Mars will require maximal use of materials found in situ and minimization of materials and equipment transported from Earth. This will mean a heavy reliance on regolith (Lunar or Marian soil) and water, supplemented by small quantities of additives fabricated on Earth. Here it is shown that SiO2-based powders, as well as Lunar and Martian regolith simulants, can be fabricated into building materials at near-ambient temperatures using only a few weight-percent of carbon nanotubes as a binder. These composites have compressive strength and toughness up to 100 MPa and 3 MPa respectively, higher than the best terrestrial concretes. They are electrically conductive (>20 S m-1) and display an extremely large piezoresistive response (gauge factor >600), allowing these composites to be used as internal sensors to monitor the structural health of extra-terrestrial buildings.

Liquid Processing of Interfacially Grown Iron-Oxide Flowers into 2D-Platelets Yields Lithium-Ion Battery Anodes with Capacities of Twice the Theoretical Value.

Iron oxide (Fe2 O3 ) is an abundant and potentially low-cost material for fabricating lithium-ion battery anodes. Here, the growth of α-Fe2 O3 nano-flowers at an electrified liquid-liquid interface is demonstrated. Sonication is used to convert these flowers into quasi-2D platelets with lateral sizes in the range of hundreds of nanometers and thicknesses in the range of tens of nanometers. These nanoplatelets can be combined with carbon nanotubes to form porous, conductive composites which can be used as electrodes in lithium-ion batteries. Using a standard activation process, these anodes display good cycling stability, reasonable rate performance and low-rate capacities approaching 1500 mAh g-1 , consistent with the current state-of-the-art for Fe2 O3 . However, by using an extended activation process, it is found that the morphology of these composites can be significantly changed, rendering the iron oxide amorphous and significantly increasing the porosity and internal surface area. These morphological changes yield anodes with very good cycling stability and low-rate capacity exceeding 2000 mAh g-1 , which is competitive with the best anode materials in the literature. However, the data implies that, after activation, the iron oxide displays a reduced solid-state lithium-ion diffusion coefficient resulting in somewhat degraded rate performance.

The examination of Fama-French Model during the Covid-19.

This paper evaluates the performance of Fama-French models on US stock markets during the selected events by studying the R 2 of the models. We find that the influence of Dotcom bubble to the R 2 of growth model is statistically significant. The R 2 of growth portfolios decreases rapidly during the Financial crisis of 2008. The latest Covid-19 outbreak drop has led to a substantial in the R 2 during this event. Furthermore, we find that all of the beta model parameters are insignificant in the GMM model.

Low-temperature synthesis and electrocatalytic application of large-area PtTe2 thin films.

The synthesis of transition metal dichalcogenides (TMDs) has been a primary focus for 2D nanomaterial research over the last 10 years, however, only a small fraction of this research has been concentrated on transition metal ditellurides. In particular, nanoscale platinum ditelluride (PtTe2) has rarely been investigated, despite its potential applications in catalysis, photonics and spintronics. Of the reports published, the majority examine mechanically-exfoliated flakes from chemical vapor transport (CVT) grown crystals. This method produces high quality-crystals, ideal for fundamental studies. However, it is very resource intensive and difficult to scale up meaning there are significant obstacles to implementation in large-scale applications. In this report, the synthesis of thin films of PtTe2 through the reaction of solid-phase precursor films is described. This offers a production method for large-area, thickness-controlled PtTe2, potentially suitable for a number of applications. These polycrystalline PtTe2 films were grown at temperatures as low as 450 °C, significantly below the typical temperatures used in the CVT synthesis methods. Adjusting the growth parameters allowed the surface coverage and morphology of the films to be controlled. Analysis with scanning electron- and scanning tunneling microscopy indicated grain sizes of above 1 µm could be achieved, comparing favorably with typical values of ∼50 nm for polycrystalline films. To investigate their potential applicability, these films were examined as electrocatalysts for the hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR). The films showed promising catalytic behavior, however, the PtTe2 was found to undergo chemical transformation to a substoichiometric chalcogenide compound under ORR conditions. This study shows while PtTe2 is stable and highly useful for in HER, this property does not apply to ORR, which undergoes a fundamentally different mechanism. This study broadens our knowledge on the electrocatalysis of TMDs.

The Rate Performance of Two-Dimensional Material-Based Battery Electrodes May Not Be as Good as Commonly Believed.

Two-dimensional (2D) materials show great potential for use in battery electrodes and are believed to be particularly promising for high-rate applications. However, there does not seem to be much hard evidence for the superior rate performance of 2D materials compared to non-2D materials. To examine this point, we have analyzed published rate-performance data for a wide range of 2D materials as well as non-2D materials for comparison. For each capacity-rate curve, we extract parameters that quantify performance which can then be analyzed using a simple mechanistic model. Contrary to expectations, by comparing a previously proposed figure of merit, we find 2D-based electrodes to be on average ∼40 times poorer in terms of rate performance than non-2D materials. This is not due to differences in solid-state diffusion times which were similarly distributed for 2D and non-2D materials. In fact, we found the main difference between 2D and non-2D materials is that ion mobility within the electrolyte-filled pores of the electrodes is significantly lower for 2D materials, a situation which we attribute to their high aspect ratios.

Production of Quasi-2D Platelets of Nonlayered Iron Pyrite (FeS2) by Liquid-Phase Exfoliation for High Performance Battery Electrodes.

Over the past 15 years, two-dimensional (2D) materials have been studied and exploited for many applications. In many cases, 2D materials are formed by the exfoliation of layered crystals such as transition-metal disulfides. However, it has recently become clear that it is possible to exfoliate nonlayered materials so long as they have a nonisotropic bonding arrangement. Here, we report the synthesis of 2D-platelets from the earth-abundant, nonlayered metal sulfide, iron pyrite (FeS2), using liquid-phase exfoliation. The resultant 2D platelets exhibit the same crystal structure as bulk pyrite but are surface passivated with a density of 14 × 1018 groups/m2. They form stable suspensions in common solvents and can be size-selected and liquid processed. Although the platelets have relatively low aspect ratios (∼5), this is in line with the anisotropic cleavage energy of bulk FeS2. We observe size-dependent changes to optical properties leading to spectroscopic metrics that can be used to estimate the dimensions of platelets. These platelets can be used to produce lithium ion battery anodes with capacities approaching 1000 mAh/g.