Dopant-additive synergism enhances perovskite solar modules.

Perovskite solar cells (PSCs) are among the most promising photovoltaic technologies owing to their exceptional optoelectronic properties1,2. However, the lower efficiency, poor stability and reproducibility issues of large-area PSCs compared with laboratory-scale PSCs are notable drawbacks that hinder their commercialization3. Here we report a synergistic dopant-additive combination strategy using methylammonium chloride (MACl) as the dopant and a Lewis-basic ionic-liquid additive, 1,3-bis(cyanomethyl)imidazolium chloride ([Bcmim]Cl). This strategy effectively inhibits the degradation of the perovskite precursor solution (PPS), suppresses the aggregation of MACl and results in phase-homogeneous and stable perovskite films with high crystallinity and fewer defects. This approach enabled the fabrication of perovskite solar modules (PSMs) that achieved a certified efficiency of 23.30% and ultimately stabilized at 22.97% over a 27.22-cm2 aperture area, marking the highest certified PSM performance. Furthermore, the PSMs showed long-term operational stability, maintaining 94.66% of the initial efficiency after 1,000 h under continuous one-sun illumination at room temperature. The interaction between [Bcmim]Cl and MACl was extensively studied to unravel the mechanism leading to an enhancement of device properties. Our approach holds substantial promise for bridging the benchtop-to-rooftop gap and advancing the production and commercialization of large-area perovskite photovoltaics.

Oxygen Vacancies on NH4 V4 O10 Accelerate Ion and Charge Transfer in Aqueous Zinc-Ion Batteries.

Vanadium-based compounds are identified as promising cathode materials for aqueous zinc ion batteries due to their high specific capacity. However, the low intrinsic conductivity and sluggish Zn2+ diffusion kinetics seriously impede their further practical application. Here, oxygen vacancies on NH4 V4 O10 is reported as a high-performing cathode material for aqueous zinc ion batteries via a facile hydrothermal strategy. The introduction of oxygen vacancy accelerates the ion and charge transfer kinetics, reduces the diffusion barrier of zinc ions, and establishes a stable crystal structure during zinc ion (de-intercalation). As a result, the oxygen vacancy enriched NH4 V4 O10 exhibits a high specific capacity of ≈499 mA h g-1 at 0.2 A g-1 , an excellent rate capability of 296 mA h g-1 at 10 A g-1 and the specific capacity cycling stability with 95.1% retention at 5 A g-1 for 4000 cycles, superior to the NVO sample (186.4 mAh g-1 at 5 A g-1 , 66% capacity retention).

Molecular Structures of Poly(methyl methacrylate) at Different Buried Interfaces Revealed by Sum Frequency Generation Vibrational Spectroscopy.

Silica or calcium fluoride (CaF2) substrate-supported poly(methyl methacrylate) (PMMA) thin films as insulating layers are commonly used in photoelectric/photovoltaic devices to improve the efficiency or stability of these devices. However, a comparative investigation of molecular structures at buried PMMA/silica and PMMA/CaF2 interfaces under thermal stimuli remains unexplored. In this study, we qualitatively and quantitatively revealed different molecular orderings and orientations of PMMA at two interfaces before and after annealing using sum frequency generation (SFG) vibrational spectroscopy. SFG vibrations were carefully assigned by using various deuterated PMMAs. SFG results indicated that, at the buried PMMA/silica interface, the side OCH3 groups were prone to lie down before annealing and tended to stand up after annealing. In contrast, the case was the opposite at the buried PMMA/CaF2 interface. The relative hydrophobicity/hydrophilicity of the two substrates and the developed hydrogen bonds upon annealing at the buried PMMA/silica interface, which is absent at the CaF2 surface, are believed to be the driving forces for different interfacial molecular structures. This study benefits the molecular-level understanding of the interfacial local structural relaxation of polymers at buried interfaces and the rational design of photoelectric/photovoltaic devices from the molecular level.

Synthesis of Antiperovskite Solid Electrolytes: Comparing Li3SI, Na3SI, and Ag3SI.

Prior calculations have predicted that chalcohalide antiperovskites may exhibit enhanced ionic mobility compared to oxyhalide antiperovskites as solid-state electrolytes. Here, the synthesis of Ag-, Li-, and Na-based chalcohalide antiperovskites is investigated using first-principles calculations and in situ synchrotron X-ray diffraction. These techniques demonstrate that the formation of Ag3SI is facilitated by the adoption of a common body centered cubic packing of S2- and I- in the reactants and products at elevated temperatures, with additional stabilization achieved by the formation of a solid solution of the anions. The absence of these two features appears to hinder the formation of the analogous Li and Na antiperovskites.

Probing Mg Intercalation in the Tetragonal Tungsten Bronze Framework V4Nb18O55.

While commercial Li-ion batteries offer the highest energy densities of current rechargeable battery technologies, their energy storage limit has almost been achieved. Therefore, there is considerable interest in Mg batteries, which could offer increased energy densities in comparison to Li-ion batteries if a high-voltage electrode material, such as a transition-metal oxide, can be developed. However, there are currently very few oxide materials which have demonstrated reversible and efficient Mg2+ insertion and extraction at high voltages; this is thought to be due to poor Mg2+ diffusion kinetics within the oxide structural framework. Herein, the authors provide conclusive evidence of electrochemical insertion of Mg2+ into the tetragonal tungsten bronze V4Nb18O55, with a maximum reversible electrochemical capacity of 75 mA h g-1, which corresponds to a magnesiated composition of Mg4V4Nb18O55. Experimental electrochemical magnesiation/demagnesiation revealed a large voltage hysteresis with charge/discharge (1.12 V vs Mg/Mg2+); when magnesiation is limited to a composition of Mg2V4Nb18O55, this hysteresis can be reduced to only 0.5 V. Hybrid-exchange density functional theory (DFT) calculations suggest that a limited number of Mg sites are accessible via low-energy diffusion pathways, but that larger kinetic barriers need to be overcome to access the entire structure. The reversible Mg2+ intercalation involved concurrent V and Nb redox activity and changes in crystal structure, as confirmed by an array of complementary methods, including powder X-ray diffraction, X-ray absorption spectroscopy, and energy-dispersive X-ray spectroscopy. Consequently, it can be concluded that the tetragonal tungsten bronzes show promise as intercalation electrode materials for Mg batteries.

Mechanisms of Degradation and Strategies for the Stabilization of Cathode-Electrolyte Interfaces in Li-Ion Batteries.

Undesired reactions at the interface between a transition metal oxide cathode and a nonaqueous electrolyte bring about challenges to the performance of Li-ion batteries in the form of compromised durability. These challenges are especially severe in extreme conditions, such as above room temperature or at high potentials. The ongoing push to increase the energy density of Li-ion batteries to break through the existing barriers of application in electric vehicles creates a compelling need to address these inefficiencies. This goal requires a combination of deep knowledge of the mechanisms underpinning reactivity, and the ability to assemble multifunctional electrode systems where different components synergistically extend cycle life by imparting interfacial stability, while maintaining, or even increasing, capacity and potential of operation. The barriers toward energy storage at high density apply equally in Li-ion, the leading technology in the battery market, and in related, emerging concepts for high energy density, such as Na-ion and Mg-ion, because they also conceptually rely on electroactive transition metal oxides. Therefore, their relevance is broad and the quest for solutions inevitable. In this Account, we describe mechanisms of reaction that can degrade the interface between a Li-ion battery electrolyte and the cathode, based on an oxide with transition metals that can reach high formal oxidation states. The focus is placed on cathodes that deliver high capacity and operate at high potential because their development would enable Li-ion battery technologies with high capacity for energy storage. Electrode-electrolyte instabilities will be identified beyond the intrinsic potential windows of stability, by linking them to the electroactive transition metals present at the surface of the electrode. These instabilities result in irreversible transformations at these interfaces, with formation of insulating layers that impede transport or material loss due to corrosion. As a result, strategies that screen the reactive surface of the oxide, while reducing the transition metal content by introducing inactive ions emerge as a logical means toward interfacial stability. Yet they must be implemented in the form of thin passivating barriers to avoid unacceptable losses in storage capacity. This Account subsequently describes our current ability to build composite structures that include the active material and phases designed to address deleterious reactions. We will discuss emerging strategies that move beyond the application of such barriers on premade agglomerated powders of the material of interest. The need for these strategies will be rationalized by the goal to effectively passivate all interfaces while fully controlling the chemistry that results at the surface and its homogeneity. Such outcomes would successfully minimize interfacial losses, thereby leading to materials that exceed the charge storage and life capabilities possible today. Practically speaking, it would create opportunities to design batteries that break the existing barriers of energy density.

Nucleation and growth process of atomic layer deposition platinum nanoparticles on strontium titanate nanocuboids.

Uniform, well-dispersed platinum nanoparticles were grown on SrTiO3 nanocuboids via atomic layer deposition (ALD) using (methylcyclopentadienyl)trimethylplatinum (MeCpPt(Me)3) and water. For the first half-cycle of the deposition particles formed through two sequential processes: initial nucleation and growth. The final particle size after a single complete ALD cycle was dependent on the reaction temperature which alters the net Pt deposition per cycle. Additional cycles resulted in further growth of previously formed particles. However, the increase in size per cycle during additional ALD cycles, beyond the first, was significantly lower as less Pt was deposited due to carbonaceous material that partially covers the surface and prevents further MeCpPt(Me)3 adsorption and reaction. The increase in particle size was also temperature dependent due to changes in the net Pt deposition. Pt nanoparticles increased in size by 59% and 76% after 15 ALD cycles for reaction temperatures of 200 °C and 300 °C, respectively. There was minimal change in the number of particles per unit area as a function of reaction time, indicating that there was minimal Ostwald ripening or secondary nucleation for the reaction conditions.

TiO2 hierarchical sub-wavelength microspheres for high efficiency dye-sensitized solar cells.

Monodisperse anatase hierarchical microspheres were produced via a simple sol-gel process. These microspheres in the sub-wavelength diameter of 320-750 nm could scatter visible light efficiently as whispering gallery modes (WGM) corresponding to the dye sensitized wavelength, and load a large number of dye molecules with a large surface area (149.82 m2 g-1). Dye-sensitized solar cells (DSCs) based on the microsphere monolayer adsorbed light fully over the entire wavelength region and facilitated electrolyte diffusion due to larger voids between the microspheres, compared to the conventional film. Furthermore, the dynamics of electron transport and recombination was investigated systematically, indicating the higher charge collection efficiency of the TiO2 microsphere film. Overall, DSCs based on the 7.5 µm hierarchical microsphere monolayer exhibited more outstanding photovoltaic performances, yielding a high power conversion efficiency (PCE) of 11.43% under simulated AM 1.5 sunlight. Half of the normal film thickness was used to cut the device cost significantly.

The role of oleic acid: from synthesis to assembly of perovskite nanocuboid two-dimensional arrays.

Oleic acid, an 18-carbon chain fatty acid, has been widely used as a surfactant to fabricate colloidal nanocrystals. In previous work, we discovered a lamellar microemulsion strategy to fabricate sub-20 nm SrTiO(3) nanocuboids using oleic acid and oleate species. Here, we demonstrate (i) the general synthesis with lamellar microemulsions of a family of compositionally varied BaxSr(1-x)TiO(3) crystalline nanocuboids with uniform size, and (ii) subsequent assembly into two-dimensional arrays by nanoparticle-bound oleate in a nonpolar solvent. The measured interparticle distance (2.4 nm) of adjacent nanoparticles in an array is less than the length of a double oleate layer (∼4 nm). On the basis of calculations of the interfacial free energy, we propose the hydrophobic, hydrocarbon-terminated groups of oleate from adjacent nanocuboids are situated closely but do not overlap. Lower aspect ratio nanocuboids are bordered by four adjacent nanocuboids which results in a uniform direction self-assembly array, whereas higher aspect ratio nanocuboids are bordered by five or six adjacent nanocuboids and can develop an arced local coordination.

Effects of electro-acupuncture on labor pain management.

PURPOSE: To evaluate the effects of a non-pharmacologic electro-acupuncture method at different acupoints on labor pain management. METHODS: Nulliparous women under the maternity care of the Department of Obstetrics and Gynecology of Sir Run Run Shaw Hospital were recruited and allocated into two experimental groups (EX-B2 group and SP6 group) and one control group, each with 60 eligible participants. Visual analog scale (VAS) was used to assess the pain during active phase of labor before and 30, 60, 120 min after intervention. The duration of active phase, the duration of second stage of labor, the duration of third stage of labor, use of oxytocin, neonatal birth weight, neonatal Apgar score at 1 and 5 min were considered as secondary outcomes of this study. RESULTS: After 30 min intervention, the mean VAS scores of both EX-B2 group and SP6 group were significantly decreased compared with the control group (P < 0.01); however, no significant difference was observed between the two experimental groups (P > 0.05). After 60 and 120 min intervention, the mean VAS scores of EX-B2 group were significantly lower than SP-6 group (P < 0.05). Both EX-B2 group and SP6 group had significant lower VAS scores after interventions and shorter time used in active phase of labor than the control group (P < 0.05). CONCLUSIONS: The study revealed that the application of electro-acupuncture at EX-B2 and SP6 acupoints could be used as a non-pharmacologic method to reduce labor pain and shorten the duration of active phase of labor.

TiO(2) nanospheres: a facile size-tunable synthesis and effective light-harvesting layer for dye-sensitized solar cells.

A facile route to synthesize amorphous TiO2 nanospheres by a controlled oxidation and hydrolysis process without any structure-directing agents or templates is presented. The size of the amorphous TiO2 nanospheres can be easily turned from 20 to 1500 nm by adjusting either the Ti species or ethanol content in the reaction solution. The phase structure of nanospheres can be controlled by hydrothermal treatment. The TiO2 nanospheres show excellent size-dependent light-scattering effects and can be structured into a light-harvesting layer for dye-sensitized solar cells with a quite high power conversion efficiency of 9.25 %.

Electrochemically Induced Phase Transformation in Vanadium Oxide Boosts Zn-Ion Intercalation.

Vanadium oxides are excellent cathode materials with large storage capacities for aqueous zinc-ion batteries, but their further development has been hampered by their low electronic conductivity and slow Zn2+ diffusion. Here, an electrochemically induced phase transformation strategy is proposed to mitigate and overcome these barriers. In situ X-ray diffraction analysis confirms the complete transformation of tunnel-like structural V6O13 into layered V5O12·6H2O during the initial electrochemical charging process. Theoretical calculations reveal that the phase transformation is crucial to reducing the Zn2+ migration energy barrier and facilitating fast charge storage kinetics. The calculated band structures indicate that the bandgap of V5O12·6H2O (0.0006 eV) is lower than that of V6O13 (0.5010 eV), which enhanced the excitation of charge carriers to the conduction band, favoring electron transfer in redox reactions. As a result, the transformed V5O12·6H2O delivers a high capacity of 609 mA h g-1 at 0.1 A g-1, superior rate performance (300 mA h g-1 at 20 A g-1), fast-charging capability (<7 min charging for 465 mA h g-1), and excellent cycling stability with a reversible capacity of 346 mA h g-1 at 5 A g-1 after 5000 cycles.

Synthesis-dependent atomic surface structures of oxide nanoparticles.

Using SrTiO3 nanocuboids as a model system, we show with aberration-corrected high resolution electron microscopy at sub-Å resolution that surface relaxations or reconstructions are present on the nanocuboids, depending on the synthetic process. Oleic acid synthesis, acetic acid synthesis, and microwave-assisted acetic acid synthesis result in a SrO termination, TiO2-rich reconstruction, and mixed termination, respectively. The experimental atomic positions are in better agreement with density functional theory calculations using an exact-exchange corrected PBEsol functional than the Perdew-Burke-Ernzerhof (PBE) functional.

KCl Treatment of CdS Electron-Transporting Layer for Improved Performance of Sb2(S,Se)3 Solar Cells.

Antimony sulfoselenide (Sb2(S,Se)3) is a promising light absorption material because of its high photoabsorption coefficient, appropriate band gap, superior stability, and abundant elemental storage. As an emerging solar material, hydrothermal deposition of Sb2(S,Se)3 solar cells has enabled a 10% efficiency threshold, where cadmium sulfide (CdS) is applied as an electron transport layer (ETL). The high-efficiency Sb2(S,Se)3 solar cells largely employ CdS as the ETL. In terms of efficiency improvement, there are two questions regarding the CdS substrate: (1) the high roughness of CdS grown on F-doped tin oxide glass which increases the roughness of the absorber layer and (2) the low conductivity of CdS films because of low purity of CdS film grown by chemical bath deposition. In this study, we demonstrate an effective potassium chloride (KCl) post-treatment to modify the CdS ETL for improving the Sb2(S,Se)3 solar cell efficiency. We found that KCl plays dual roles that reduce roughness and enhance conductivity of the CdS films, thus acquiring a maximum efficiency of 9.98%, which is 9.2% higher than the control device. This study provides a new method for the surface engineering of CdS layer to improve the morphological and electrical properties, which is significant for improving the performance of CdS-based thin-film solar cells.

Addition of Dioxane in Electrolyte Promotes (002)-Textured Zinc Growth and Suppressed Side Reactions in Zinc-Ion Batteries.

The reversibility and cyclability of aqueous zinc-ion batteries (ZIBs) are largely determined by the stabilization of the Zn anode. Therefore, a stable anode/electrolyte interface capable of inhibiting dendrites and side reactions is crucial for high-performing ZIBs. In this study, we investigated the adsorption of 1,4-dioxane (DX) to promote the exposure of Zn (002) facets and prevent dendrite growth. DX appears to reside at the interface and suppress the detrimental side reactions. ZIBs with the addition of DX demonstrated a long-term cycling stability of 1000 h in harsh conditions of 10 mA cm-2 with an ultrahigh cumulative plated capacity of 5 Ah cm-2 and shows a good reversibility with an average Coulombic efficiency of 99.7%. The Zn//NH4V4O10 full battery with DX achieves a high specific capacity (202 mAh g-1 at 5 A g-1) and capacity retention (90.6% after 5000 cycles), much better than that of ZIBs with the pristine ZnSO4 electrolyte. By selectively adjusting the Zn2+ deposition rate on the crystal facets with adsorbed molecules, this work provides a promising modulation strategy at the molecular level for high-performing Zn anodes and can potentially be applied to other metal anodes suffering from instability and irreversibility.

Cycling of block copolymer composites with lithium-conducting ceramic nanoparticles.

Solid polymer and perovskite-type ceramic electrolytes have both shown promise in advancing solid-state lithium metal batteries. Despite their favorable interfacial stability against lithium metal, polymer electrolytes face issues due to their low ionic conductivity and poor mechanical strength. Highly conductive and mechanically robust ceramics, on the other hand, cannot physically remain in contact with redox-active particles that expand and contract during charge-discharge cycles unless excessive pressures are used. To overcome the disadvantages of each material, polymer-ceramic composites can be formed; however, depletion interactions will always lead to aggregation of the ceramic particles if a homopolymer above its melting temperature is used. In this study, we incorporate Li0.33La0.56TiO3 (LLTO) nanoparticles into a block copolymer, polystyrene-b-poly (ethylene oxide) (SEO), to develop a polymer-composite electrolyte (SEO-LLTO). TEMs of the same nanoparticles in polyethylene oxide (PEO) show highly aggregated particles whereas a significant fraction of the nanoparticles are dispersed within the PEO-rich lamellae of the SEO-LLTO electrolyte. We use synchrotron hard x-ray microtomography to study the cell failure and interfacial stability of SEO-LLTO in cycled lithium-lithium symmetric cells. Three-dimensional tomograms reveal the formation of large globular lithium structures in the vicinity of the LLTO aggregates. Encasing the SEO-LLTO between layers of SEO to form a "sandwich" electrolyte, we prevent direct contact of LLTO with lithium metal, which allows for the passage of seven-fold higher current densities without signatures of lithium deposition around LLTO. We posit that eliminating particle clustering and direct contact of LLTO and lithium metal through dry processing techniques is crucial to enabling composite electrolytes.

Analysis of the impact of noninvasive prenatal testing for trisomies 21 and 18 in twin pregnancies undergoing artificial reproductive technology.

PURPOSE: The purpose of this study was to evaluate the performance and impact of noninvasive prenatal screening (NIPS) on twin pregnancies. PATIENTS AND METHODS: Twin pregnancies after artificial reproductive technology(ART) were tested by NIPS for screening trisomy 21, 18, and 13 in a single medical center in Hangzhou. Positive NIPS results were confirmed by karyotyping, while negative results were interviewed after delivery. RESULTS: From January 2019 to December 2020, 474 twin pregnancies were tested by NIPS for screening trisomy 21, 18, and 13 in a single medical center in Hangzhou. The performance of NIPS had been evaluated compared to the invasive diagnostic results. The positive predictive value (PPV) of NIPS for chromosome 21 and 18 aneuploidies is 80% (95CI, 36.09-96.59) and 100%, respectively. The incidence of trisomy 21, and 18 chromosome aneuploidies among the twin pregnancies undergoing ART was 0.84% and 0.21%, respectively. CONCLUSION: The performance of NIPS was substantially accurate among the twin pregnancies after ART in this study, and NIPS potentially avoided a considerable part of aneuploidies liveborn in twin pregnancies in Hangzhou.

A study on formation of titanium oxide nanoribbons.

The transformation process of nanoribbons produced by the hydrothermal treatment in 10 M NaOH solution at 200 degrees C was investigated systematically via electron microscopy. Field emission scanning electron microscope (FE-SEM) observation showed that the treatment duration had a strong effect on the product morphology from the hollow nanotubes to nanoribbons. The details of transformation were studied by transmission electron miscroscopy. Some nanotubes assembled into clusters and grew into nanowires as the grain to form the nanoribbons, whilemost of nanotubes dissolved into the solution again.

A facile chemical route to synthesize ZnO nanoarrays: one-dimensional nanowire arrays and two-dimensional porous nanosheet arrays.

A facile chemical route is presented to synthesize ZnO nanoarrays including one-dimensional nanowire arrays and two-dimensional porous nanosheet arrays. Large-scale ZnO nanowire arrays with the length of 5 microm and aspect ratio of 42 were achieved by cyclic growth in aqueous solution. After being immerged in the zinc acetate solution for 24 h, the ZnO nanowire arrays converted to sheet-like Zn5(OH)8(CH3COO)2 arrays. Subsequently, the sheet-like Zn5(OH)8(CH3COO)2 arrays converted to the porous ZnO nanosheet arrays by annealing treatment. As demonstrated by the performance of dye-sensitized solar cells (DSC), the porous ZnO nanosheet arrays can improve the efficiency of DSC effectively. In addition, the synthesized ZnO nanoarrays have potential applications in solar cells, catalysis, sensors and other nanodevices.

Regulating the Film Growth and Reducing the Defects for Efficient CsPbIBr2 Solar Cells.

Inorganic lead halide perovskite CsPbIBr2 possesses good stability with a suitable band gap for tandem solar cells. Decreasing the defect concentration and improving the film quality is crucial to further increase the power conversion efficiency of CsPbIBr2 solar cells. Here, the crystallization dynamics of CsPbIBr2 films is regulated by introducing the volatile organic salt, formamidinium acetate (FAAc) into the precursor solution. It is found that FAAc slows the crystallization process of CsPbIBr2 films and pinhole-free films with large grains and smooth surfaces are obtained. The defect concentration of the films is decreased and the nonradiative recombination is significantly inhibited. By improving the film quality, the FAAc remarkably enhances the efficiency of CsPbIBr2 solar cells. The champion device delivers a power conversion efficiency of 9.44% and exhibits higher stability than the reference device. This finding provides an effective strategy for reducing defects, suppressing the recombination, and improving the performance of CsPbIBr2 solar cells.