Rapid analysis of diclofenac in freshwater and wastewater by a monoclonal antibody-based highly sensitive ELISA.

The non-steroidal anti-inflammatory drug (NSAID) diclofenac (DCF) is found worldwide in the aqueous environment. Therefore, it has raised increased public concern on potential long-term impact on human health and wildlife. The importance of DCF has been emphasized by the European Union recently by including this pharmaceutical in the first watch list of priority hazardous substances in order to gather Union-wide monitoring data. Rapid and cheap methods of analysis are therefore required for fresh and wastewater monitoring with high sample load. Here, for the first time, well-characterized monoclonal antibodies (mAbs) against DCF were generated and a highly sensitive ELISA developed. The best antibody (mAb 12G5) is highly affine (KD = 1.5 × 10(-10) M), stable to potential matrix interferences such as pH value (pH range 5.2-9.2), calcium ion concentration (up to 75 mg/L), and humic acid content (up to 20 mg/L). The limit of detection (LOD, S/N = 3) and IC50 of the ELISA calibration curve were 7.8 and 44 ng/L, respectively. The working range was defined between 11 and 180 ng/L. On average, about 10 % cross-reactivity (CR) was found for DCF metabolites 5-OH-DCF, 4'-OH-DCF, and DCF-acyl glucuronide, but other structurally related NSAIDs showed binding <1 % compared to the parent compound. While DCF concentrations at the low ppt range were measured in river and lake water, higher values of 2.9 and 2.1 µg/L were found in wastewater influents and effluents, respectively. These results could be confirmed by solid phase extraction combined with LC-MS.

Layer-by-layer generation of PEG-based regenerable immunosensing surfaces for small-sized analytes.

Small molecules (haptens) like pharmaceuticals or peptides can serve as targets for antibody binding in competitive immunoassay-based flow-through assays. In this work, a strategy for preparing polyethylene glycol (PEG) coatings for subsequent hapten immobilization on glass-type silica surfaces is presented and characterized in detail. Two substrates bearing terminal silanol groups were utilized, a glass slide and a silicon wafer. First, surfaces were thoroughly cleaned and pretreated to generate additional silanol groups. Then, a silane layer with terminal epoxy groups was created using 3-glycidyloxypropyltrimethoxysilane (GOPTS). Epoxy groups were used to bind a layer of diamino-poly(ethylene glycol) (DAPEG) with terminal amino groups. Finally, the low molecular weight compound diclofenac was bound to the surface to be used as model ligand for competitive biosensing of haptens. The elementary steps were characterized using atomic force microscopy (AFM), water contact angle measurement, grazing-angle attenuated total reflection (GA-ATR) FT-IR spectroscopy, and X-ray photoelectron spectroscopy (XPS). The data collected using these techniques have confirmed the successive grafting of the molecular species, evidencing, that homogeneous monolayers were created on the silica surfaces and validated the proposed mechanism of functionalization. The resulting surfaces were used to investigate polyclonal anti-diclofenac antibodies recognition and reversibility using quartz crystal microbalance with dissipation (QCM-D) measurements or an automated flow-through immunoassay with chemiluminescence (CL) read-out. For both techniques, recognition and reversibility of the antibody binding were observed. The stability of sensors over time was also assessed and no decrease in CL response was observed upon 14 days in aqueous solution. The herein presented strategy for surface functionalization can be used in the future as reproducible and reusable universal platform for hapten biosensors.

A glyco-chip for the detection of ricin by an automated chemiluminescence read-out system.

The plant toxin ricin is a lectin that binds to D-galactose or lactose moieties by multivalent interactions. In the present work, this avidity was used to develop a novel sandwich glyco-immunoassay using a carbohydrate microarray. For realization, 6-azidohexyl-lactose was immobilized on an alkyne silane surface by Cu(I) catalyzed click chemistry. This procedure is fast, and prevents any nonspecific binding on the microarray surface. Ricin binds via its B-chain to the lactose moieties, and is detected by the biotinylated anti-ricin A-chain. By adding a horseradish peroxidase-labeled streptavidin, a chemiluminescence signal can be generated. This method is described as a sandwich-type glyco-immunoassay. The signal on the glyco-chip can be regenerated for at least 10 measurements. The limit of detection was estimated to be 80 ng mL(-1). The assay was carried out on the automated microarray readout platform MCR 3. In this way, it took 20 min for one measurement, including regeneration of the chip surface.