RESUMEN
A counter-propagating laser-beam platform using a spherical plasma mirror was developed for the kilojoule-class petawatt LFEX laser. The temporal and spatial overlaps of the incoming and redirected beams were measured with an optical interferometer and an x-ray pinhole camera. The plasma mirror performance was evaluated by measuring fast electrons, ions, and neutrons generated in the counter-propagating laser interaction with a Cu-doped deuterated film on both sides. The reflectivity and peak intensity were estimated as â¼50% and â¼5 × 1018 W/cm2, respectively. The platform could enable studies of counter-streaming charged particles in high-energy-density plasmas for fundamental and inertial confinement fusion research.
RESUMEN
Fast isochoric laser heating is a scheme to heat matter with a relativistic intensity (>10^{18} W/cm^{2}) laser pulse for producing an ultrahigh-energy-density (UHED) state. We have demonstrated an efficient fast isochoric heating of a compressed dense plasma core with a multipicosecond kilojoule-class petawatt laser and an assistance of externally applied kilotesla magnetic fields for guiding fast electrons to the dense plasma. A UHED state of 2.2 PPa is achieved experimentally with 4.6 kJ of total laser energy that is one order of magnitude lower than the energy used in the conventional implosion scheme. A two-dimensional particle-in-cell simulation confirmed that diffusive heating from a laser-plasma interaction zone to the dense plasma plays an essential role to the efficient creation of the UHED state.
RESUMEN
To generate bright water-window (WW) soft x rays (2.3-4.4 nm), gold slab targets were irradiated with laser pulses (1064 nm, 7 ns, 1 J). Emission spectroscopy showed that the introduction of low-pressure nitrogen enhanced the soft x-ray yield emitted from the laser-produced Au plasma. The intensity of the WW x-ray transported in a 400-Pa N2 atmosphere from the laser-produced plasma increased by 3.8 times over that in vacuum. Considering a strong x-ray absorption, the x-ray yield emitted directly from the Au plasma in the N2 gas was evaluated to be 13 times higher than that in vacuum. Although similar measurements were made for various gases, only N2 gas causes an increase in a soft x-ray yield. The processes leading to this enhancement mechanism were revealed by using hydrodynamic simulation and atomic structure codes.
RESUMEN
To develop laser-ignition technology, transparent glass plates were artificially sooted and irradiated repetitively by laser from the front (sooted) and back sides separately. Generally, the back-side irradiation was more effective at soot removal. However, the cleaning effect was saturated after thousands of laser shots. Although the saturated soot quantity was a decreasing function of the laser fluence per pulse, its magnitude remained the same for both front-side and back-side irradiations. In examining several soot-removal mechanisms proposed so far, it was found that the aerodynamic force produced by the flow induced by the laser heating of the soot was the most plausible mechanism.
RESUMEN
For improving the laser absorption efficiency in laser ignition, the transmitted laser light was returned to the laser-produced plasma by using a corner cube. In the experiments, the transmitted light was reinjected into the plasma at different times. The laser absorption efficiency was found to be substantially improved when the transmitted light was reinjected into the plasma after adequate plasma expansion. Furthermore, through visualization experiments on gas-dynamics phenomena, it was found that the reinjection of the transmitted light affected not only the laser absorption efficiency but also the gas dynamics after breakdown, and thereby the initial flame kernel development.
RESUMEN
Fast isochoric heating of a pre-compressed plasma core with a high-intensity short-pulse laser is an attractive and alternative approach to create ultra-high-energy-density states like those found in inertial confinement fusion (ICF) ignition sparks. Laser-produced relativistic electron beam (REB) deposits a part of kinetic energy in the core, and then the heated region becomes the hot spark to trigger the ignition. However, due to the inherent large angular spread of the produced REB, only a small portion of the REB collides with the core. Here, we demonstrate a factor-of-two enhancement of laser-to-core energy coupling with the magnetized fast isochoric heating. The method employs a magnetic field of hundreds of Tesla that is applied to the transport region from the REB generation zone to the core which results in guiding the REB along the magnetic field lines to the core. This scheme may provide more efficient energy coupling compared to the conventional ICF scheme.
RESUMEN
We report an experimental demonstration of controlling plasma flow direction with a magnetic nozzle consisting of multiple coils. Four coils are controlled separately to form an asymmetric magnetic field to change the direction of laser-produced plasma flow. The ablation plasma deforms the topology of the external magnetic field, forming a magnetic cavity inside and compressing the field outside. The compressed magnetic field pushes the plasma via the Lorentz force on a diamagnetic current: j × B in a certain direction, depending on the magnetic field configuration. Plasma and magnetic field structure formations depending on the initial magnetic field were simultaneously measured with a self-emission gated optical imager and B-dot probe, respectively, and the probe measurement clearly shows the difference of plasma expansion direction between symmetric and asymmetric initial magnetic fields. The combination of two-dimensional radiation hydrodynamic and three-dimensional hybrid simulations shows the control of the deflection angle with different number of coils, forming a plasma structure similar to that observed in the experiment.
RESUMEN
A series of experiments were carried out to evaluate the energy-coupling efficiency from heating laser to a fuel core in the fast-ignition scheme of laser-driven inertial confinement fusion. Although the efficiency is determined by a wide variety of complex physics, from intense laser plasma interactions to the properties of high-energy density plasmas and the transport of relativistic electron beams (REB), here we simplify the physics by breaking down the efficiency into three measurable parameters: (i) energy conversion ratio from laser to REB, (ii) probability of collision between the REB and the fusion fuel core, and (iii) fraction of energy deposited in the fuel core from the REB. These three parameters were measured with the newly developed experimental platform designed for mimicking the plasma conditions of a realistic integrated fast-ignition experiment. The experimental results indicate that the high-energy tail of REB must be suppressed to heat the fuel core efficiently.
RESUMEN
Laboratory generation of strong magnetic fields opens new frontiers in plasma and beam physics, astro- and solar-physics, materials science, and atomic and molecular physics. Although kilotesla magnetic fields have already been produced by magnetic flux compression using an imploding metal tube or plasma shell, accessibility at multiple points and better controlled shapes of the field are desirable. Here we have generated kilotesla magnetic fields using a capacitor-coil target, in which two nickel disks are connected by a U-turn coil. A magnetic flux density of 1.5â kT was measured using the Faraday effect 650â µm away from the coil, when the capacitor was driven by two beams from the GEKKO-XII laser (at 1â kJ (total), 1.3â ns, 0.53 or 1â µm, and 5 × 10(16)â W/cm(2)).
RESUMEN
A scheme to suppress the Rayleigh-Taylor instability has been investigated for a direct-drive inertial fusion target. In a high-Z doped-plastic target, two ablation surfaces are formed separately-one driven by thermal radiation and the other driven by electron conduction. The growth of the Rayleigh-Taylor instability is significantly suppressed on the radiation-driven ablation surface inside the target due to the large ablation velocity and long density scale length. A significant reduction of the growth rate was observed in simulations and experiments using a brominated plastic target. A new direct-drive pellet was designed using this scheme.