Precise Modulation of Triple-Phase Boundaries towards a Highly Functional Exsolved Catalyst for Dry Reforming of Methane under a Dilution-Free System.

Dry reforming of methane (DRM) has been emerging as a viable solution to achieving carbon neutrality enhanced by the Paris Agreement as it converts the greenhouse gases of CO2 and CH4 into industrially useful syngas. However, there have been limited studies on the DRM catalyst under mild operating conditions with a high dilution gas ratio due to their deactivation from carbon coking and metal sintering. Herein, we apply the triple-phase boundary (TPB) concept to DRM catalyst via exsolution phenomenon that can secure elongated TPB by controlling the Fe-doping ratio in perovskite oxide. Remarkably, the exsolved catalyst with prolongated TPB shows exceptional CO2 and CH4 conversion rates of 95.9 % and 91.6 %, respectively, stable for 1000 hours under a dilution-free system. DFT calculations confirm that the Lewis acid of support and Lewis base of metal at the TPB promote the adsorption of reactants, resulting in lowering the overall CO2 dissociation and CH4 dehydrogenation energy.

Probing One-Dimensional Oxygen Vacancy Channels Driven by Cation-Anion Double Ordering in Perovskites.

Visualizing the oxygen vacancy distributions is highly desirable for understanding the atomistic oxygen diffusion mechanisms in perovskites. In particular, the direct observation of the one-dimensional oxygen vacancy channels has not yet been achieved in perovskites with dual ion (i.e., cation and anion) ordering. Here, we perform atomic-resolution imaging of the one-dimensional oxygen vacancy channels and their structural dynamics in a NdBaCo2O5.5 double perovskite oxide. An in situ heating transmission electron microscopy investigation reveals the disordering of oxygen vacancy channels by local rearrangement of oxygen vacancies at the specific temperature. A density functional theory calculation suggests that the possible pathway of oxygen vacancy migration is a multistep route via Co-O and Nd-Ov (oxygen vacancy) sites. These findings could provide robust guidance for understanding the static and dynamic behaviors of oxygen vacancies in perovskite oxides.

A Bifunctional Hybrid Electrocatalyst for Oxygen Reduction and Oxygen Evolution Reactions: Nano-Co3O4-Deposited La0.5Sr0.5MnO3 via Infiltration.

For rechargeable metal-air batteries, which are a promising energy storage device for renewable and sustainable energy technologies, the development of cost-effective electrocatalysts with effective bifunctional activity for both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) has been a challenging task. To realize highly effective ORR and OER electrocatalysts, we present a hybrid catalyst, Co3O4-infiltrated La0.5Sr0.5MnO3-δ (LSM@Co3O4), synthesized using an electrospray and infiltration technique. This study expands the scope of the infiltration technique by depositing ~18 nm nanoparticles on unprecedented ~70 nm nano-scaffolds. The hybrid LSM@Co3O4 catalyst exhibits high catalytic activities for both ORR and OER (~7 times, ~1.5 times, and ~1.6 times higher than LSM, Co3O4, and IrO2, respectively) in terms of onset potential and limiting current density. Moreover, with the LSM@Co3O4, the number of electrons transferred reaches four, indicating that the catalyst is effective in the reduction reaction of O2 via a direct four-electron pathway. The study demonstrates that hybrid catalysts are a promising approach for oxygen electrocatalysts for renewable and sustainable energy devices.

Enhancing Thermocatalytic Activities by Upshifting the d-Band Center of Exsolved Co-Ni-Fe Ternary Alloy Nanoparticles for the Dry Reforming of Methane.

Dry reforming of methane (DRM) is a feasible solution to address the reduction of greenhouse gases stipulated by the Paris Climate Agreement, given that it adds value by converting trivial gases, CO2 and CH4 , simultaneously into useful syngas. However, the conventional Ni catalyst undergoes deactivation due to carbon coking and particle agglomeration. Here we demonstrate a highly efficient and durable DRM catalyst: exsolved Co-Ni-Fe ternary alloy nanoparticles on the layered perovskite PrBaMn1.7 Co0.1 Ni0.2 O5+δ produced by topotactic exsolution. This method readily allows the generation of a larger number of exsolved nanoparticles with enhanced catalytic activity above that of Ni monometallic and Co-Ni bimetallic particles. The enhancement is achieved by the upshift of the d-band center of Co-Ni-Fe relative to those of Co-Ni and Ni, meaning easier charge donation to the adsorbate. Furthermore, the exsolved catalyst shows exceptional stability, with continuous DRM operation for about 350 hours.

Highly Efficient CO2 Utilization via Aqueous Zinc- or Aluminum-CO2 Systems for Hydrogen Gas Evolution and Electricity Production.

Atmospheric carbon dioxide (CO2 ) has increased from 278 to 408 parts per million (ppm) over the industrial period and has critically impacted climate change. In response to this crisis, carbon capture, utilization, and storage/sequestration technologies have been studied. So far, however, the economic feasibility of the existing conversion technologies is still inadequate owing to sluggish CO2 conversion. Herein, we report an aqueous zinc- and aluminum-CO2 system that utilizes acidity from spontaneous dissolution of CO2 in aqueous solution to generate electrical energy and hydrogen (H2 ). The system has a positively shifted onset potential of hydrogen evolution reaction (HER) by 0.4 V compared to a typical HER under alkaline conditions and facile HER kinetics with low Tafel slope of 34 mV dec-1 . The Al-CO2 system has a maximum power density of 125 mW cm-2 which is the highest value among CO2 utilization electrochemical system.

Defect-Free Encapsulation of Fe0 in 2D Fused Organic Networks as a Durable Oxygen Reduction Electrocatalyst.

Because they provide lower cost but comparable activity to precious platinum (Pt)-based catalysts, nonprecious iron (Fe)-based materials, such as Fe/Fe3C and Fe-N-C, have gained considerable attention as electrocatalysts for the oxygen reduction reaction (ORR). However, their practical application is hindered by their poor stability, which is attributed to the defective protection of extremely unstable Fe nanoparticles. Here, we introduce a synthesis strategy for a stable Fe-based electrocatalyst, which was realized by defect-free encapsulation of Fe nanoparticles using a two-dimensional (2D) phenazine-based fused aromatic porous organic network (Aza-PON). The resulting Fe@Aza-PON catalyst showed electrocatalytic activity (half-wave potential, 0.839 V; Tafel slope, 60 mV decade-1) comparable to commercial Pt on activated carbon (Pt/C, 0.826 V and 90 mV decade-1). More importantly, the Fe@Aza-PON displayed outstanding stability (zero current loss even after 100 000 cycles) and tolerance against contamination (methanol and CO poisoning). In a hybrid Li-air battery test, the Fe@Aza-PON demonstrated performance superior to Pt/C.

A Tailored Bifunctional Electrocatalyst: Boosting Oxygen Reduction/Evolution Catalysis via Electron Transfer Between N-Doped Graphene and Perovskite Oxides.

Fabricating perovskite oxide/carbon material composite catalysts is a widely accepted strategy to enhance oxygen reduction reaction/oxygen evolution reaction (ORR and OER) catalytic activities. Herein, synthesized, porous, perovskite-type Sm0.5 Sr0.5 CoO3-δ hollow nanofibers (SSC-HF) are hybridized with cross-linked, 3D, N-doped graphene (3DNG). This rationally designed hybrid catalyst, SSC-HF-3DNG (SSC-HG), exhibits a remarkable enhancement in ORR/OER activity in alkaline media. The synergistic effects between SSC and 3DNG during their ORR and OER processes are firstly revealed by density functional theory calculations. It suggests that electron transport from 3DNG to O2 and SSC increases the activity of electrocatalytic reactions (ORR and OER) by activating O2 , increasing the covalent bonding of lattice oxygen. This electron transfer-accelerated catalysis behavior in SSC-HG will provide design guidelines for composites of perovskite and carbon with bifunctional catalysts.

Porous Cobalt Phosphide Polyhedrons with Iron Doping as an Efficient Bifunctional Electrocatalyst.

Iron (Fe)-doped porous cobalt phosphide polyhedrons are designed and synthesized as an efficient bifunctional electrocatalyst for both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). The synthesis strategy involves one-step route for doping foreign metallic element and forming porous cobalt phosphide polyhedrons. With varying doping levels of Fe, the optimized Fe-doped porous cobalt phosphide polyhedron exhibits significantly enhanced HER and OER performances, including low onset overpotentials, large current densities, as well as small Tafel slopes and good electrochemical stability during HER and OER.

Layered oxygen-deficient double perovskite as an efficient and stable anode for direct hydrocarbon solid oxide fuel cells.

Different layered perovskite-related oxides are known to exhibit important electronic, magnetic and electrochemical properties. Owing to their excellent mixed-ionic and electronic conductivity and fast oxygen kinetics, cation layered double perovskite oxides such as PrBaCo2O5 in particular have exhibited excellent properties as solid oxide fuel cell oxygen electrodes. Here, we show for the first time that related layered materials can be used as high-performance fuel electrodes. Good redox stability with tolerance to coking and sulphur contamination from hydrocarbon fuels is demonstrated for the layered perovskite anode PrBaMn2O5+δ (PBMO). The PBMO anode is fabricated by in situ annealing of Pr0.5Ba0.5MnO3-δ in fuel conditions and actual fuel cell operation is demonstrated. At 800 °C, layered PBMO shows high electrical conductivity of 8.16 S cm(-1) in 5% H2 and demonstrates peak power densities of 1.7 and 1.3 W cm(-2) at 850 °C using humidified hydrogen and propane fuels, respectively.

Achieving High Efficiency and Eliminating Degradation in Solid Oxide Electrochemical Cells Using High Oxygen-Capacity Perovskite.

Recently, there have been efforts to use clean and renewable energy because of finite fossil fuels and environmental problems. Owing to the site-specific and weather-dependent characteristics of the renewable energy supply, solid oxide electrolysis cells (SOECs) have received considerable attention to store energy as hydrogen. Conventional SOECs use Ni-YSZ (yttria-stabilized zirconia) and LSM (strontium-doped lanthanum manganites)-YSZ as electrodes. These electrodes, however, suffer from redox-instability and coarsening of the Ni electrode along with delamination of the LSM electrode during steam electrolysis. In this study, we successfully design and fabricate highly efficient SOECs using layered perovskites, PrBaMn2 O5+δ (PBM) and PrBa0.5 Sr0.5 Co1.5 Fe0.5 O5+δ (PBSCF50), as both electrodes for the first time. The SOEC with layered perovskites as both-side electrodes shows outstanding performance, reversible cycling, and remarkable stability over 600 hours.

Solid oxide electrolysis: Concluding remarks.

Renewable energy resources such as solar energy, wind energy, hydropower or geothermal energy have attracted significant attention in recent years. Renewable energy sources have to match supply with demand, therefore it is essential that energy storage devices (e.g., secondary batteries) are developed. However, secondary batteries are accompanied with critical problems such as high cost for the limited energy storage capacity and loss of charge over time. Energy storage in the form of chemical species, such as H2 or CO2, have no constraints on energy storage capacity and will also be essential. When plentiful renewable energy exists, for example, it could be used to convert H2O into hydrogen via water electrolysis. Also, renewable energy resources could be used to reduce CO2 into CO and recycle CO2 and H2O into sustainable hydrocarbon fuels in solid oxide electrolysis (SOE).

Oxygen deficient layered double perovskite as an active cathode for CO2 electrolysis using a solid oxide conductor.

A-site ordered PrBaMn2O(5+δ) was investigated as a potential cathode for CO2 electrolysis using a La(0.9)Sr(0.1)Ga(0.8)Mg(0.2)O3 (LSGM) electrolyte. The A-site ordered layered double perovskite, PrBaMn2O(5+δ), was found to enhance electrocatalytic activity for CO2 reduction on the cathode side since it supports mixed valent transition metal cations such as Mn, which could provide high electrical conductivity and maintain a large oxygen vacancy content, contributing to fast oxygen ion diffusion. It was found that during the oxidation of the reduced PrBaMn2O(5+δ) (O5 phase) to PrBaMn2O(6-δ) (O6 phase), a reversible oxygen switchover in the lattice takes place. In addition, here the successful CO2 electrolysis was measured in LSGM electrolyte with this novel oxide electrode. It was found that this PrBaMn2O(5+δ), layered perovskite cathode exhibits a performance with a current density of 0.85 A cm(-2) at 1.5 V and 850 °C and the electrochemical properties were also evaluated by impedance spectroscopy.

Conductivity-Dependent Completion of Oxygen Reduction on Oxide Catalysts.

The electric conductivity-dependence of the number of electrons transferred during the oxygen reduction reaction is presented. Intensive properties, such as the number of electrons transferred, are difficult to be considered conductivity-dependent. Four different perovskite oxide catalysts of different conductivities were investigated with varying carbon contents. More conductive environments surrounding active sites, achieved by more conductive catalysts (providing internal electric pathways) or higher carbon content (providing external electric pathways), resulted in higher number of electrons transferred toward more complete 4e reduction of oxygen, and also changed the rate-determining steps from two-step 2e process to a single-step 1e process. Experimental evidence of the conductivity dependency was described by a microscopic ohmic polarization model based on effective potential localized nearby the active sites.

Etched graphite with internally grown Si nanowires from pores as an anode for high density Li-ion batteries.

A novel architecture consisting of Si nanowires internally grown from porous graphite is synthesized by etching of graphite with a lamellar structure via a VLS (vapor-liquid-solid) process. This strategy gives the high electrode density of 1.5 g/cm(3), which is comparable with practical anode of the Li-ion battery. Our product demonstrates a high volumetric capacity density of 1363 mAh/cm(3) with 91% Coulombic efficiency and high rate capability of 568 mAh/cm(3) even at a 5C rate. This good electrochemical performance allows porous graphite to offer free space to accommodate the volume change of Si nanowires during cycling and the electron transport to efficiently be improved between active materials.

Development of double-perovskite compounds as cathode materials for low-temperature solid oxide fuel cells.

A class of double-perovskite compounds display fast oxygen ion diffusion and high catalytic activity toward oxygen reduction while maintaining excellent compatibility with the electrolyte. The astoundingly extended stability of NdBa(1-x)Ca(x)Co2O(5+δ) (NBCaCO) under both air and CO2-containing atmosphere is reported along with excellent electrochemical performance by only Ca doping into the A site of NdBaCo2O(5+δ) (NBCO). The enhanced stability can be ascribed to both the increased electron affinity of mobile oxygen species with Ca, determined through density functional theory calculations and the increased redox stability from the coulometric titration.

Suppressing Structure Delamination for Enhanced Electrochemical Performance of Solid Oxide Cells.

Reversible solid oxide cells (rSOCs) have significant potential as efficient energy conversion and storage systems. Nevertheless, the practical application of their conventional air electrodes, such as La0.8Sr0.2MnO3-δ (LSM), Ba0.5Sr0.5Co0.8Fe0.2O3-δ (BSCF), and PrBa0.8Ca0.2Co2O5+δ (PBCC), remains unsatisfactory due to interface delamination during prolonged electrochemical operation. Using micro-focusing X-ray absorption spectroscopy (µ-XAS), a decrease (increase) in the co-valence state from the electrode surface to the electrode/electrolyte interface is observed, leading to the above delamination. Utilizing the one-pot method to incorporate an oxygen-vacancy-enriched CeO2 electrode into these air electrodes, the uniform distribution of the Co valence state is observed, alleviating the structural delamination. PBCC-CeO2 electrodes exhibited a degradation rate of 0.095 mV h-1 at 650 °C during a nearly 500-h test as compared with 0.907 mV h-1 observed during the 135-h test for PBCC. Additionally, a remarkable increase in electrolysis current density from 636 to 934 mA cm-2 under 1.3 V and a maximum power density from 912 to 989 mW cm-2 upon incorporating CeO2 into PBCC is also observed. BSCF-CeO2 and LSM-CeO2 also show enhanced electrochemical performance and prolonged stability as compared to BSCF and LSM. This work offers a strategy to mitigate the structural delamination of conventional electrodes to boost the performance of rSOCs.

High redox and performance stability of layered SmBa(0.5)Sr(0.5)Co(1.5)Cu(0.5)O(5+δ) perovskite cathodes for intermediate-temperature solid oxide fuel cells.

Cobalt-containing cathodes often encounter problems such as high thermal expansion coefficients (TEC) and poor stability, making them unsuitable for practical use as cathode materials for intermediate-temperature solid oxide fuel cells (IT-SOFCs). This study focuses on the effects of Cu doping in the Co site of SmBa0.5Sr0.5Co2O5+δ in terms of structural characteristics, electrical properties, electrochemical performance, redox properties, and performance stability as an IT-SOFC cathode material. The TEC value of a SmBa0.5Sr0.5Co1.5Cu0.5O5+δ (SBSCCu50) sample is 12.8 × 10(-6) K(-1), which is lower than that (13.7 × 10(-6) K(-1)) of a SmBa0.5Sr0.5Co2O5+δ (SBSCO) sample at 700 °C. SBSCCu50 showed higher redox stability at lower p(O2) and a more stable cell power output while retaining desirable electrochemical performance, as compared with SBSCO. SBSCCu50 displayed reduced TEC values and enhanced redox and performance stability, as well as satisfactory electrical properties and electrochemical performance under typical fuel cell operating conditions. The results indicate that SBSCCu50 is a promising material as a cathode for IT-SOFCs.

Recent Progress and Future Prospects of Anions O-site Doped Perovskite Oxides in Electrocatalysis for Various Electrochemical Systems.

With the rapid development of novel energy conversion and storage technologies, there is a growing demand for enhanced performance in a wide range of electrocatalysts. Perovskite oxides (ABO3 ) have caused widespread concerns due to their excellent electrocatalytic properties, low cost, stable and reliable performance. In recent years, the research on anion O-site doping of perovskite oxides has been a cynosure, which is considered as a promising route for enhancing performance. However, a systematic review summarizing the research progress of anion-doped perovskite oxides is still lacking. Therefore, this review mainly introduces the elements and strategies of various common anions doped at O-site of perovskite oxides, analyzes their influence on the physical and chemical properties of perovskites, and separately concludes their applications in electrocatalysis. This review will provide ideas and prospects for the development of subsequent anion doping strategies for high performance perovskite oxides.

Concurrent oxygen reduction and water oxidation at high ionic strength for scalable electrosynthesis of hydrogen peroxide.

Electrosynthesis of hydrogen peroxide via selective two-electron transfer oxygen reduction or water oxidation reactions offers a cleaner, cost-effective alternative to anthraquinone processes. However, it remains a challenge to achieve high Faradaic efficiencies at elevated current densities. Herein, we report that oxygen-deficient Pr1.0Sr1.0Fe0.75Zn0.25O4-δ perovskite oxides rich of oxygen vacancies can favorably bind the reaction intermediates to facilitate selective and efficient two-electron transfer pathways. These oxides exhibited superior Faradic efficiencies (~99%) for oxygen reduction over a wide potential range (0.05 to 0.45 V versus reversible hydrogen electrode) and current densities surpassing 50 mA cm-2 under high ionic strengths. We further found that the oxides perform a high selectivity (~80%) for two-electron transfer water oxidation reaction at a low overpotential (0.39 V). Lastly, we devised a membrane-free electrolyser employing bifunctional electrocatalysts, achieving a record-high Faradaic efficiency of 163.0% at 2.10 V and 50 mA cm-2. This marks the first report of the concurrent oxygen reduction and water oxidation catalysed by efficient bifunctional oxides in a novel membrane-free electrolyser for scalable hydrogen peroxide electrosynthesis.

Rheumatoid Arthritis and Risk of Parkinson Disease in Korea.

Importance: Although it has been postulated that chronic inflammation caused by rheumatoid arthritis (RA) contributes to the development of Parkinson disease (PD), the association between these 2 conditions has yet to be determined. Objective: To evaluate the association between RA and subsequent PD risk. Design, Setting, and Participants: This retrospective cohort study used the Korean National Health Insurance Service database to collect population-based, nationally representative data on patients with RA enrolled from 2010 to 2017 and followed up until 2019 (median follow-up, 4.3 [IQR, 2.6-6.4] years after a 1-year lag). A total of 119 788 patients who were first diagnosed with RA (83 064 with seropositive RA [SPRA], 36 724 with seronegative RA [SNRA]) were identified during the study period and included those who underwent a national health checkup within 2 years before the RA diagnosis date (64 457 patients). After applying exclusion criteria (eg, age <40 years, other rheumatic diseases, previous PD), 54 680 patients (39 010 with SPRA, 15 670 with SNRA) were included. A 1:5 age- and sex-matched control group of patients without RA was also included for a total control population of 273 400. Exposures: Rheumatoid arthritis as defined using International Classification of Diseases, Tenth Revision codes M05 for SPRA and M06 (except M06.1 and M06.4) for SNRA; prescription of any disease-modifying antirheumatic drug; and enrollment in the Korean Rare and Intractable Diseases program. Main Outcomes and Measures: The main outcome was newly diagnosed PD. Data were analyzed from May 10 through August 1, 2022, using Cox proportional hazards regression analyses. Results: From the 328 080 individuals analyzed (mean [SD] age, 58.6 [10.1] years; 74.9% female and 25.1% male), 1093 developed PD (803 controls and 290 with RA). Participants with RA had a 1.74-fold higher risk of PD vs controls (95% CI, 1.52-1.99). An increased risk of PD was found in patients with SPRA (adjusted hazard ratio [aHR], 1.95; 95% CI, 1.68-2.26) but not in patients with SNRA (aHR, 1.20; 95% CI, 0.91-1.57). Compared with the SNRA group, those with SPRA had a higher risk of PD (aHR, 1.61; 95% CI, 1.20-2.16). There was no significant interaction between covariates on risk of PD. Conclusions and Relevance: In this study, RA was associated with an increased risk of PD, and seropositivity of RA conferred an augmented risk of PD. The findings suggest that physicians should be aware of the elevated risk of PD in patients with RA and promptly refer patients to a neurologist at onset of early motor symptoms of PD without synovitis.