Strong Photoluminescence Enhancement in Molybdenum Disulfide in Aqueous Media.

The interface between conventional semiconductors and aqueous ionic solutions is an important target in chemistry and materials science. Recently, a wide variety of research has been done on transition-metal dichalcogenides (TMDCs) for use as 2D layered semiconductors, and their optoelectronic properties have been widely explored. One representative TMDC, monolayer (1L) MoS2, is known to show a photoluminescence (PL) signal of a direct band gap nature, and the PL intensity is dependent on the carrier concentration. Various methods of 1L MoS2 carrier modulation have been shown to enhance the PL intensity in dry environments. In contrast, enhancement in an aqueous environment is limited, and a strategy to design an interface with aqueous media has not yet been established. One proposed idea was an aqueous acid interface; however, the enhancement of the PL with this method was usually minimal, about 1 order of magnitude. In this study, we demonstrate a method to achieve strong PL enhancement in 1L MoS2 in an aqueous media by incorporating bis(trifluoromethane)sulfonyl anion (TFSI- ion) in an acidic environment. With the addition of the TFSI- ion in an acidic environment, the enhancement factor of the PL in 1L MoS2 is more than 100 times greater than its PL intensity in water. The molecular anion is the key factor, as the TFSI- ion facilitates the oxidation of MoS2. This anionic effect is the additional factor needed to modulate the optoelectronic properties of 2D semiconductors in aqueous media. The proposed idea could have potential applications for biochemical sensors in aqueous situations.

Fully integrated wearable sensor arrays for multiplexed in situ perspiration analysis.

Wearable sensor technologies are essential to the realization of personalized medicine through continuously monitoring an individual's state of health. Sampling human sweat, which is rich in physiological information, could enable non-invasive monitoring. Previously reported sweat-based and other non-invasive biosensors either can only monitor a single analyte at a time or lack on-site signal processing circuitry and sensor calibration mechanisms for accurate analysis of the physiological state. Given the complexity of sweat secretion, simultaneous and multiplexed screening of target biomarkers is critical and requires full system integration to ensure the accuracy of measurements. Here we present a mechanically flexible and fully integrated (that is, no external analysis is needed) sensor array for multiplexed in situ perspiration analysis, which simultaneously and selectively measures sweat metabolites (such as glucose and lactate) and electrolytes (such as sodium and potassium ions), as well as the skin temperature (to calibrate the response of the sensors). Our work bridges the technological gap between signal transduction, conditioning (amplification and filtering), processing and wireless transmission in wearable biosensors by merging plastic-based sensors that interface with the skin with silicon integrated circuits consolidated on a flexible circuit board for complex signal processing. This application could not have been realized using either of these technologies alone owing to their respective inherent limitations. The wearable system is used to measure the detailed sweat profile of human subjects engaged in prolonged indoor and outdoor physical activities, and to make a real-time assessment of the physiological state of the subjects. This platform enables a wide range of personalized diagnostic and physiological monitoring applications.

Photoconductive Coordination Polymer with a Lead-Sulfur Two-Dimensional Coordination Sheet Structure.

Coordination polymers with metal-sulfur (M-S) bonds in their nodes have interesting optical properties and can be used as photocatalysts for water splitting. A wide range of inorganic-organic hybrid materials with M-S bonds have been prepared in recent years. However, there is a dearth of structural information because of their low crystallinity, which has hampered the understanding of their underlying chemistry and physics. Thus, we conducted a structural study of a novel, highly crystalline coordination polymer with M-S bonds. Theoretical calculations were performed to elucidate its photoconductivity mechanism. The photoconductive, three-dimensional coordination polymer [Pb(tadt)]n (denoted as KGF-9; tadt = 1,3,4-thiadiazole-2,5-dithiolate) was synthesized and confirmed to have a three-dimensional structure containing a two-dimensional Pb-S framework by single-crystal X-ray diffraction. We also performed diffuse-reflectance ultraviolet-visible-near-infrared spectroscopy, time-resolved microwave conductivity, and photoelectron yield spectroscopy measurements on the bulk powder samples, as well as first-principles calculations. Additionally, direct-current photoconductivity measurements were conducted on a single-crystal sample.

Single-layered assembly of vanadium pentoxide nanowires on graphene for nanowire-based lithography technique.

Graphene nanoribbon (GNR)-based materials are a promising device material because of their potential high carrier mobility and atomically thin structure. Various approaches have been reported for preparing the GNR-based materials, from bottom-up chemical synthetic procedures to top-down fabrication techniques using lithography of graphene. However, it is still difficult to prepare a large-scale GNR-based material. Here, we develop a procedure to prepare a large-scale GNR network using networked single-layer inorganic nanowires. Vanadium pentoxide (V2O5) nanowires were assembled on graphene with an interfacial layer of a cationic polymer via electrostatic interaction. A large-scale nanowire network can be prepared on graphene and is stable enough for applying an oxygen plasma. Using plasma etching, a networked graphene structure can be generated. Removing the nanowires results in a networked flat structure whose both surface morphology and Raman spectrum indicate a GNR networked structure. The field-effect device indicates the semiconducting character of the GNR networked structure. This work would be useful for fabricating a large-scale GNR-based material as a platform for GNR junctions for physics and electronic circuits.

Flexible Electronics toward Wearable Sensing.

Wearable sensors play a crucial role in realizing personalized medicine, as they can continuously collect data from the human body to capture meaningful health status changes in time for preventive intervention. However, motion artifacts and mechanical mismatches between conventional rigid electronic materials and soft skin often lead to substantial sensor errors during epidermal measurement. Because of its unique properties such as high flexibility and conformability, flexible electronics enables a natural interaction between electronics and the human body. In this Account, we summarize our recent studies on the design of flexible electronic devices and systems for physical and chemical monitoring. Material innovation, sensor design, device fabrication, system integration, and human studies employed toward continuous and noninvasive wearable sensing are discussed. A flexible electronic device typically contains several key components, including the substrate, the active layer, and the interface layer. The inorganic-nanomaterials-based active layer (prepared by a physical transfer or solution process) is shown to have good physicochemical properties, electron/hole mobility, and mechanical strength. Flexible electronics based on the printed and transferred active materials has shown great promise for physical sensing. For example, integrating a nanowire transistor array for the active matrix and a conductive pressure-sensitive rubber enables tactile pressure mapping; tactile-pressure-sensitive e-skin and organic light-emitting diodes can be integrated for instantaneous pressure visualization. Such printed sensors have been applied as wearable patches to monitor skin temperature, electrocardiograms, and human activities. In addition, liquid metals could serve as an attractive candidate for flexible electronics because of their excellent conductivity, flexibility, and stretchability. Liquid-metal-enabled electronics (based on liquid-liquid heterojunctions and embedded microchannels) have been utilized to monitor a wide range of physiological parameters (e.g., pulse and temperature). Despite the rapid growth in wearable sensing technologies, there is an urgent need for the development of flexible devices that can capture molecular data from the human body to retrieve more insightful health information. We have developed a wearable and flexible sweat-sensing platform toward real-time multiplexed perspiration analysis. An integrated iontophoresis module on a wearable sweat sensor could enable autonomous and programmed sweat extraction. A microfluidics-based sensing system was demonstrated for sweat sampling, sensing, and sweat rate analysis. Roll-to-roll gravure printing allows for mass production of high-performance flexible chemical sensors at low cost. These wearable and flexible sweat sensors have shown great promise in dehydration monitoring, cystic fibrosis diagnosis, drug monitoring, and noninvasive glucose monitoring. Future work in this field should focus on designing robust wearable sensing systems to accurately collect data from the human body and on large-scale human studies to determine how the measured physical and chemical information relates to the individual's specific health conditions. Further research in these directions, along with the large sets of data collected via these wearable and flexible sensing technologies, will have a significant impact on future personalized healthcare.

Systematic Study of Photoluminescence Enhancement in Monolayer Molybdenum Disulfide by Acid Treatment.

Monolayer molybdenum disulfide (MoS2) is an atomically thin semiconducting material with a direct band gap. This physical property is attributable to atomically thin optical devices such as sensors, light-emitting devices, and photovoltaic cells. Recently, a near-unity photoluminescence (PL) quantum yield of a monolayer MoS2 was demonstrated via a treatment with a molecular acid, bis(trifluoromethane)sulfonimide (TFSI); however, the mechanism still remains a mystery. Here, we work on PL enhancement of monolayer MoS2 by treatment of Brønsted acids (TFSI and sulfuric acid (H2SO4)) to identify the importance of the protonated environment. In TFSI as an acid, different solvents-1,2-dichloroethane (DCE), acetonitrile, and water-were studied, as they show quite different acidity in solution. All of the solvents showed PL enhancement, and the highest was observed in DCE. This behavior in DCE would be due to the higher acidity than others have. Acids from different anions can also be studied in water as a common solvent. Both TFSI and H2SO4 showed similar PL enhancement (∼4-8 enhancement) at the same proton concentration, indicating that the proton is a key factor to enhance the PL intensity. Finally, we considered another cation, Li+ from Li2SO4, instead of H2SO4, in water. Although Li and H atoms showed similar binding energy on MoS2 from theoretical calculations, Li2SO4 treatment showed little PL enhancement; only coexisting H2SO4 reproduced the enhancement. This study demonstrated the importance of a protonated environment to increase the PL intensity of monolayer MoS2. The study will lead to a solution to achieve high optical quality and to implementation for atomically thin optical devices.

Measuring the Edge Recombination Velocity of Monolayer Semiconductors.

Understanding edge effects and quantifying their impact on the carrier properties of two-dimensional (2D) semiconductors is an essential step toward utilizing this material for high performance electronic and optoelectronic devices. WS2 monolayers patterned into disks of varying diameters are used to experimentally explore the influence of edges on the material's optical properties. Carrier lifetime measurements show a decrease in the effective lifetime, τeffective, as a function of decreasing diameter, suggesting that the edges are active sites for carrier recombination. Accordingly, we introduce a metric called edge recombination velocity (ERV) to characterize the impact of 2D material edges on nonradiative carrier recombination. The unpassivated WS2 monolayer disks yield an ERV ∼ 4 × 104 cm/s. This work quantifies the nonradiative recombination edge effects in monolayer semiconductors, while simultaneously establishing a practical characterization approach that can be used to experimentally explore edge passivation methods for 2D materials.

Recombination Kinetics and Effects of Superacid Treatment in Sulfur- and Selenium-Based Transition Metal Dichalcogenides.

Optoelectronic devices based on two-dimensional (2D) materials have shown tremendous promise over the past few years; however, there are still numerous challenges that need to be overcome to enable their application in devices. These include improving their poor photoluminescence (PL) quantum yield (QY) as well as better understanding of exciton-based recombination kinetics. Recently, we developed a chemical treatment technique using an organic superacid, bis(trifluoromethane)sulfonimide (TFSI), which was shown to improve the quantum yield in MoS2 from less than 1% to over 95%. Here, we perform detailed steady-state and transient optical characterization on some of the most heavily studied direct bandgap 2D materials, specifically WS2, MoS2, WSe2, and MoSe2, over a large pump dynamic range to study the recombination mechanisms present in these materials. We then explore the effects of TFSI treatment on the PL QY and recombination kinetics for each case. Our results suggest that sulfur-based 2D materials are amenable to repair/passivation by TFSI, while the mechanism is thus far ineffective on selenium based systems. We also show that biexcitonic recombination is the dominant nonradiative pathway in these materials and that the kinetics for TFSI treated MoS2 and WS2 can be described using a simple two parameter model.

General Thermal Texturization Process of MoS2 for Efficient Electrocatalytic Hydrogen Evolution Reaction.

Molybdenum disulfide (MoS2) has been widely examined as a catalyst containing no precious metals for the hydrogen evolution reaction (HER); however, these examinations have utilized synthesized MoS2 because the pristine MoS2 mineral is known to be a poor catalyst. The fundamental challenge with pristine MoS2 is the inert HER activity of the predominant (0001) basal surface plane. In order to achieve high HER performance with pristine MoS2, it is essential to activate the basal plane. Here, we report a general thermal process in which the basal plane is texturized to increase the density of HER-active edge sites. This texturization is achieved through a simple thermal annealing procedure in a hydrogen environment, removing sulfur from the MoS2 surface to form edge sites. As a result, the process generates high HER catalytic performance in pristine MoS2 across various morphologies such as the bulk mineral, films composed of micron-scale flakes, and even films of a commercially available spray of nanoflake MoS2. The lowest overpotential (η) observed for these samples was η = 170 mV to obtain 10 mA/cm(2) of HER current density.

Highly uniform and stable n-type carbon nanotube transistors by using positively charged silicon nitride thin films.

Air-stable n-doping of carbon nanotubes is presented by utilizing SiN(x) thin films deposited by plasma-enhanced chemical vapor deposition. The fixed positive charges in SiN(x), arising from (+)Si ≡ N3 dangling bonds induce strong field-effect doping of underlying nanotubes. Specifically, an electron doping density of ∼ 10(20) cm(-3) is estimated from capacitance voltage measurements of the fixed charge within the SiN(x). This high doping concentration results in thinning of the Schottky barrier widths at the nanotube/metal contacts, thus allowing for efficient injection of electrons by tunnelling. As a proof-of-concept, n-type thin-film transistors using random networks of semiconductor-enriched nanotubes are presented with an electron mobility of ∼ 10 cm(2)/V s, which is comparable to the hole mobility of as-made p-type devices. The devices are highly stable without any noticeable change in the electrical properties upon exposure to ambient air for 30 days. Furthermore, the devices exhibit high uniformity over large areas, which is an important requirement for use in practical applications. The work presents a robust approach for physicochemical doping of carbon nanotubes by relying on field-effect rather than a charge transfer mechanism.

Air-stable surface charge transfer doping of MoS2 by benzyl viologen.

Air-stable doping of transition metal dichalcogenides is of fundamental importance to enable a wide range of optoelectronic and electronic devices while exploring their basic material properties. Here we demonstrate the use of benzyl viologen (BV), which has one of the highest reduction potentials of all electron-donor organic compounds, as a surface charge transfer donor for MoS2 flakes. The n-doped samples exhibit excellent stability in both ambient air and vacuum. Notably, we obtained a high electron sheet density of ~1.2 × 10(13) cm(-2), which corresponds to the degenerate doping limit for MoS2. The BV dopant molecules can be reversibly removed by immersion in toluene, providing the ability to control the carrier sheet density as well as selective removal of surface dopants on demand. By BV doping of MoS2 at the metal junctions, the contact resistances are shown to be reduced by a factor of >3. As a proof of concept, top-gated field-effect transistors were fabricated with BV-doped n(+) source/drain contacts self-aligned with respect to the top gate. The device architecture, resembling that of the conventional Si transistors, exhibited excellent switching characteristics with a subthreshold swing of ~77 mV/decade.

Design of surfactant-substrate interactions for roll-to-roll assembly of carbon nanotubes for thin-film transistors.

Controlled assembly of single-walled carbon nanotube (SWCNT) networks with high density and deposition rate is critical for many practical applications, including large-area electronics. In this regard, surfactant chemistry plays a critical role as it facilitates the substrate-nanotube interactions. Despite its importance, detailed understanding of the subject up until now has been lacking, especially toward tuning the controllability of SWCNT assembly for thin-film transistors. Here, we explore SWCNT assembly with steroid- and alkyl-based surfactants. While steroid-based surfactants yield highly dense nanotube thin films, alkyl surfactants are found to prohibit nanotube assembly. The latter is attributed to the formation of packed alkyl layers of residual surfactants on the substrate surface, which subsequently repel surfactant encapsulated SWCNTs. In addition, temperature is found to enhance the nanotube deposition rate and density. Using this knowledge, we demonstrate highly dense and rapid assembly with an effective SWCNT surface coverage of ~99% as characterized by capacitance-voltage measurements. The scalability of the process is demonstrated through a roll-to-roll assembly of SWCNTs on plastic substrates for large-area thin-film transistors. The work presents an important process scheme for nanomanufacturing of SWCNT-based electronics.

Metre-long cell-laden microfibres exhibit tissue morphologies and functions.

Artificial reconstruction of fibre-shaped cellular constructs could greatly contribute to tissue assembly in vitro. Here we show that, by using a microfluidic device with double-coaxial laminar flow, metre-long core-shell hydrogel microfibres encapsulating ECM proteins and differentiated cells or somatic stem cells can be fabricated, and that the microfibres reconstitute intrinsic morphologies and functions of living tissues. We also show that these functional fibres can be assembled, by weaving and reeling, into macroscopic cellular structures with various spatial patterns. Moreover, fibres encapsulating primary pancreatic islet cells and transplanted through a microcatheter into the subrenal capsular space of diabetic mice normalized blood glucose concentrations for about two weeks. These microfibres may find use as templates for the reconstruction of fibre-shaped functional tissues that mimic muscle fibres, blood vessels or nerve networks in vivo.

Carbon nanotube active-matrix backplanes for mechanically flexible visible light and X-ray imagers.

We report visible light and X-ray imagers on lightweight and mechanically flexible plastic substrates. The process involves solution processing of organic photodetectors on top of an active-matrix backplane consisting of carbon nanotube thin-film transistors. The system takes advantage of the high mobility of nanotube transistors for low operating voltages and efficient light absorption of organic bulk-heterojunctions for high imaging sensitivity. With this highly scalable process scheme, 18 × 18 pixel-array flexible imagers (physical size of 2 cm × 1.5 cm) with high performance are successfully demonstrated. In addition, as the absorption peak of the adopted organic photodiodes covers the green band of the light spectrum, X-ray imaging is readily demonstrated by placing a scintillator film on top of the flexible imagers.

Solution-Processed Flexible Temperature Sensor Array for Highly Resolved Spatial Temperature and Tactile Mapping Using ESN-Based Data Interpolation.

High-performance flexible temperature sensors are crucial in various technological applications, such as monitoring environmental conditions and human healthcare. The ideal characteristics of these sensors for stable temperature monitoring include scalability, mechanical flexibility, and high sensitivity. Moreover, simplicity and low power consumption will be essential for temperature sensor arrays in future integrated systems. This study introduces a solution-based approach for creating a V2O5 nanowire network temperature sensor on a flexible film. Through optimization of the fabrication conditions, the sensor exhibits remarkable performance, sustaining long-term stability (>110 h) with minimal hysteresis and excellent sensitivity (∼-1.5%/°C). In addition, this study employs machine learning techniques for data interpolation among sensors, thereby enhancing the spatial resolution of temperature measurements and adding tactile mapping without increasing the sensor count. Introducing this methodology results in an improved understanding of temperature variations, advancing the capabilities of flexible-sensor arrays for various applications.

Selective Isolation of Mono- to Quadlayered 2D Materials via Sonication-Assisted Micromechanical Exfoliation.

Mechanical exfoliation methods of two-dimensional materials have been an essential process for advanced devices and fundamental sciences. However, the exfoliation method usually generates various thick flakes, and a bunch of thick bulk flakes usually covers an entire substrate. Here, we developed a method to selectively isolate mono- to quadlayers of transition metal dichalcogenides (TMDCs) by sonication in organic solvents. The analysis reveals the importance of low interface energies between solvents and TMDCs, leading to the effective removal of bulk flakes under sonication. Importantly, a monolayer adjacent to bulk flakes shows cleavage at the interface, and the monolayer can be selectively isolated on the substrate. This approach can extend to preparing a monolayer device with crowded 17 electrode fingers surrounding the monolayer and for the measurement of electrostatic device performance.

Unusual Selective Monitoring of N,N-Dimethylformamide in a Two-Dimensional Material Field-Effect Transistor.

N,N-Dimethylformamide (DMF) is an essential solvent in industries and pharmaceutics. Its market size range was estimated to be 2 billion U.S. dollars in 2022. Monitoring DMF in solution environments in real time is significant because of its toxicity. However, DMF is not a redox-active molecule; therefore, selective monitoring of DMF in solutions, especially in polar aqueous solutions, in real time is extremely difficult. In this paper, we propose a selective DMF sensor using a molybdenum disulfide (MoS2) field-effect transistor (FET). The sensor responds to DMF molecules but not to similar molecules of formamide, N,N-diethylformamide, and N,N-dimethylacetamide. The plausible atomic mechanism is the oxygen substitution sites on MoS2, on which the DMF molecule shows an exceptional orientation. The thin structure of MoS2-FET can be incorporated into a microfluidic chamber, which leads to DMF monitoring in real time by exchanging solutions subsequently. The designed device shows DMF monitoring in NaCl ionic solutions from 1 to 200 µL/mL. This work proposes the concept of selectively monitoring redox-inactive molecules based on the nonideal atomic affinity site on the surface of two-dimensional semiconductors.

Metallic Transport in Monolayer and Multilayer Molybdenum Disulfides by Molecular Surface Charge Transfer Doping.

Carrier modulation in transition-metal dichalcogenides (TMDCs) is of importance for applying electronic devices to tune their transport properties and controlling phases, including metallic to superconductivity. Although the surface charge transfer doping method has shown a strong modulation ability of the electronic structures in TMDCs and a degenerately doped state has been proposed, the details of the electronic states have not been elucidated, and this transport behavior should show a considerable thickness dependence in TMDCs. In this study, we characterize the metallic transport behavior in the monolayer and multilayer MoS2 under surface charge transfer doping with a strong electron dopant, benzyl viologen (BV) molecules. The metallic behavior transforms to an insulative state under a negative gate voltage. Consequently, metal-insulator transition (MIT) was observed in both monolayer and multilayer MoS2 correlating with the critical conductivity of order e2/h. In the multilayer case, the BV molecules strongly modulated the topmost surface layer in the bulk MoS2; the transfer characteristics suggested a crossover from a heterogeneously doped state with a doped topmost layer to doping in the deep layers caused by the variation in the gate voltage. The findings of this work will be useful for understanding the device characteristics of thin-layered materials and for applying them to the controlling phases via carrier modulation.

Ultralarge Photoluminescence Enhancement of Monolayer Molybdenum Disulfide by Spontaneous Superacid Nanolayer Formation.

Due to the direct band gap nature, extensive studies have been conducted to improve the optical behavior in monolayer transition metal dichalcogenides (TMDCs) with a formula of MX2 (M = Mo, W; X = S, Se, Te). One of the strongest modulating agents of optical behavior is a molecular superacid treatment; however, the chemical event has not been unveiled. Also, the engineering protocol for keeping the treatment is immature. In this work, we systematically study the superacid treatment procedures on monolayer molybdenum disulfide (MoS2) and propose that the interaction, a hydrophilic interaction, between the superacid molecule and MoS2 surface would be critical. As a result of the interaction, the superacid molecules spontaneously form an acidic layer with the thickness of several nanometers on the surface. The power-dependent photoluminescence (PL) measurement indicates the edge of MoS2 flake is more effective and electronically modulated by the treatment. By understanding the superacid nanolayer formation by the treatment, we succeeded in maintaining the ultrastrong PL in the superacid-treated MoS2 for more than 30 days in the ambient air by encapsulation with transparent organic polymers. This study advances the understanding and designing applications of strong luminescent properties in the superacid-treated TMDCs and paves the way toward engineering exciton dynamics and an experimental platform for treating multibody states.