RESUMEN
During the manufacturing process of liposome formulations, it is considered difficult to evaluate their physicochemical properties and biological profiles due to the complexity of their structure and manufacturing process. Conventional quality evaluation is labor-intensive and time-consuming; therefore, there was a need to introduce a method that could perform in-line, real-time evaluation during the manufacturing process. In this study, Raman spectroscopy was used to monitor in real time the encapsulation of drugs into liposomes and the drug release, which are particularly important quality evaluation items. Furthermore, Raman spectroscopy combined with partial least-squares (PLS) analysis was used for quantitative drug evaluation to assess consistency with results from UV-visible spectrophotometry (UV), a common quantification method. The prepared various ciprofloxacin (CPFX) liposomes were placed in cellulose tubes, and a probe-type Raman spectrophotometer was used to monitor drug encapsulation, the removal of unencapsulated drug, and drug release characteristics in real time using a dialysis method. In the Raman spectra of the liposomes prepared by remote loading, the intensities of the CPFX-derived peaks increased upon drug encapsulation and showed a slight decrease upon removal of the unencapsulated drug. Furthermore, the peak intensity decreased more gradually during the drug release. In all Raman monitoring experiments, the discrepancy between quantified values of CPFX concentration in liposomes, as measured by Raman spectroscopy combined with partial least-squares (PLS) analysis, and those obtained through ultraviolet (UV) spectrophotometry was within 6.7%. The results revealed that the quantitative evaluation of drugs using a combination of Raman spectroscopy and PLS analysis was as accurate as the evaluation using UV spectrophotometry, which was used for comparison. These results indicate the promising potential of Raman spectroscopy as an innovative method for the quality evaluation of liposomal formulations.
Asunto(s)
Celulosa , Liposomas , Composición de Medicamentos/métodos , Espectrometría Raman/métodosRESUMEN
PURPOSE: We fabricated and characterized polyvinyl alcohol (PVA)-based dissolving microneedles (MNs) for transdermal drug delivery of apomorphine hydrochloride (APO), which is used in treating the wearing-off phenomenon observed in Parkinson's disease. METHODS: We fabricated MN arrays with 11 × 11 needles of four different lengths (300, 600, 900, and 1200 µm) by micromolding. The APO-loaded dissolving MNs were characterized in terms of their physicochemical and functional properties. We also compared the pharmacokinetic parameters after drug administration using MNs with those after subcutaneous injection by analyzing the blood concentration of APO in rats. RESULTS: PVA-based dissolving MNs longer than 600 µm could effectively puncture the stratum corneum of the rat skin with penetrability of approximately one-third of the needle length. Although APO is known to have chemical stability issues in aqueous solutions, the drug content in APO-loaded MNs was retained at 25°C for 12 weeks. The concentration of APO after the administration of APO-loaded 600-µm MNs that dissolved completely in skin within 60 min was 81%. The absorption of 200-µg APO delivered by MNs showed a Tmax of 20 min, Cmax of 76 ng/mL, and AUC0-120 min of 2,829 ngã»min/mL, compared with a Tmax of 5 min, Cmax of 126 ng/mL, and AUC0-120 min of 3,224 ngã»min/mL for subcutaneous injection. The bioavailability in terms of AUC0-120 min of APO delivered by MNs was 88%. CONCLUSION: APO-loaded dissolving MNs can deliver APO via skin into the systemic circulation with rapid absorption and high bioavailability.
Asunto(s)
Apomorfina , Enfermedad de Parkinson , Ratas , Animales , Apomorfina/farmacología , Sistemas de Liberación de Medicamentos , Enfermedad de Parkinson/tratamiento farmacológico , Administración Cutánea , PielRESUMEN
The spectrum of 31P-NMR is fundamentally simpler than that of 1H-NMR; consequently identifying the target signal(s) for quantitation is simpler using quantitative 31P-NMR (31P-qNMR) than using quantitative 1H-NMR (1H-qNMR), which has been already established as an absolute determination method. We have previously reported a 31P-qNMR method for the absolute determination of cyclophosphamide hydrate and sofosbuvir as water-soluble and water-insoluble organophosphorus compounds, respectively. This study introduces the purity determination of brigatinib (BR), an organophosphorus compound with limited water solubility, using 31P-qNMR at multiple laboratories. Phosphonoacetic acid (PAA) and 1,4-BTMSB-d4 were selected as the reference standards (RSs) for 31P-qNMR and 1H-qNMR, respectively. The qNMR solvents were chosen based on the solubilities of BR and the RSs for qNMR. CD3OH was selected as the solvent for 31P-qNMR measurements to prevent the influence of deuterium exchange caused by the presence of exchangeable intramolecular protons of BR and PAA on the quantitative values, while CD3OD was the solvent of choice for the 1H-qNMR measurements to prevent the influence of water signals and the exchangeable intramolecular protons of BR and PAA. The mean purity of BR determined by 31P-qNMR was 97.94 ± 0.69%, which was in agreement with that determined by 1H-qNMR (97.26 ± 0.71%), thus indicating the feasibility of purity determination of BR by 31P-qNMR. Therefore, the findings of this study may provide an effective method that is simpler than conventional 1H-qNMR for the determination of organophosphorus compounds.
Asunto(s)
Compuestos Organofosforados , Protones , Estándares de Referencia , Agua , SolventesRESUMEN
In pharmaceutics, substandard drug manufacturing can sometimes occur. Usually, end-product release tests are conducted to detect defective products, but in many cases, they are not able to identify the root causes of quality defects. In recent years, chemical imaging techniques have been widely used to study quality defects by visualizing the distribution of components in solid dosage forms. However, in most studies, the causes are predicted from images of ingredients, and the impact of each factor is unclear. In this study, we prepared model tablets and intentionally changed only the distribution of disintegrants, and visualized this distribution using the Raman chemical imaging technique to evaluate the effect on the dissolution behavior of the tablets. We found that tablet disintegration occurs completely when the amount of disintegrant is sufficient to disintegrate the tablet and is distributed throughout the tablet, even if the distribution is not uniform. In contrast, if there was a large area where the disintegrant was not present, the tablet did not disintegrate sufficiently. This suggests that it is more important that a sufficient amount of disintegrant is present throughout the tablet rather than the degree of deviation of disintegrant distribution.
Asunto(s)
Química Farmacéutica , Excipientes , Química Farmacéutica/métodos , Solubilidad , ComprimidosRESUMEN
In the present study, we conducted a detailed evaluation of the effects of humidification on the quality of five types of commercial magnesium oxide (MgO) tablet formulations. When near-IR spectroscopy was performed, a peak derived from the first overtone of the stretching vibration of the hydroxyl group was observed at approximately 7200 cm-1 in a humidified MgO tablet formulation. To visually evaluate the effect of this humidification, a mapping image was created using microscopic IR spectroscopy. In the IR spectrum, a peak derived from the stretching vibration of the hydroxyl group appears at approximately 3700 cm-1, so we created a mapping image using the absorbance ratio of 3700 and 3400 cm-1 as an index. In the mapping image of humidified MgO tablet formulations, many areas had a higher absorbance ratio than the dried tablet formulations. From these results, it is qualitatively confirmed that the MgO was changed to magnesium hydroxide (Mg(OH)2) by humidification. Although these results were observed in the four types of MgO tablet formulations, only one type of tablet formulation was less affected by humidification. In addition, although most tablet formulations tended to prolong disintegration time due to humidification, there was almost no effect of humidification on the disintegration time in one type of tablet formulation, which had little change in the above evaluation. Thus, in most commercial MgO tablet formulations, humidification prolongs the disintegration time, and Mg(OH)2 significantly contributes to this factor.
Asunto(s)
Óxido de Magnesio , Óxido de Magnesio/química , Dureza , Comprimidos/química , SolubilidadRESUMEN
Quantitative 1H-NMR (1H-qNMR) is useful for determining the absolute purity of organic molecules; however, it is sometimes difficult to identify the target signal(s) for quantitation because of their overlap and complexity. Therefore, we focused on the 31P nucleus because of the simplicity of its signals and previously reported 31P-qNMR in D2O. Here we report 31P-qNMR of an organophosphorus compound, sofosbuvir (SOF), which is soluble in organic solvents. Phosphonoacetic acid (PAA) and 1,4-bis(trimethylsilyl)benzene-d4 (1,4-BTMSB-d4) were used as reference standards for 31P-qNMR and 1H-qNMR, respectively, in methanol-d4. The purity of SOF determined by 31P-qNMR was 100.63 ± 0.95%, whereas that determined by 1H-qNMR was 99.07 ± 0.50%. The average half bandwidths of the 31P signal of PAA and SOF were 3.38 ± 2.39 and 2.22 ± 0.19 Hz, respectively, suggesting that the T2 relaxation time of the PAA signal was shorter than that of SOF and varied among test laboratories. This difference most likely arose from the instability in the chemical shift due to the deuterium exchange of the acidic protons of PAA, which decreased the integrated intensity of the PAA signal. Next, an aprotic solvent, dimethyl sulfoxide-d6 (DMSO-d6), was used as the dissolving solvent with PAA and sodium 4,4-dimethyl-4-silapentanesulfonate-d6 (DSS-d6) as reference standards for 31P-qNMR and 1H-qNMR, respectively. SOF purities determined by 31P-qNMR and 1H-qNMR were 99.10 ± 0.30 and 99.44 ± 0.29%, respectively. SOF purities determined by 31P-qNMR agreed with the established 1H-qNMR values, suggesting that an aprotic solvent is preferable for 31P-qNMR because it is unnecessary to consider the effect of deuterium exchange.
Asunto(s)
Imagen por Resonancia Magnética , Sofosbuvir , Deuterio , Espectroscopía de Resonancia Magnética , Estándares de Referencia , SolventesRESUMEN
A rapid and nondestructive analytical technique is critical for the analysis of cyclodextrin inclusion complexes in solid dosage forms. This study proposed a newly developed low-frequency Raman spectroscopy as a candidate technique for the analysis of cyclodextrin inclusion complexes. In this study, we selected a typical series of five crystalline cyclodextrin inclusion complexes and reported the usefulness of Raman spectroscopy for analyzing these inclusion complexes. Some inclusion complexes clearly differed from the raw materials in conventional Raman spectra. In another case, though specific differences were not observed between inclusion complexes and raw materials in conventional Raman spectra, clear differences were observed in low-frequency Raman spectra. Moreover, no characteristic differences between inclusion complexes consisting of different guest molecules were observed in conventional Raman spectra. The characteristic differences were observed only in low-frequency Raman spectra. Therefore, low-frequency Raman spectroscopy is a useful technique for solid-state analysis of crystalline inclusion complexes.
Asunto(s)
Técnicas Electroquímicas , Espectrometría Raman/métodos , alfa-Ciclodextrinas/química , Química Farmacéutica/métodos , Formas de Dosificación , Estructura MolecularRESUMEN
Vibrational spectroscopic imaging has become useful analytical tools for quality control of drug products. In this study, we applied microscopic attenuated total reflection (ATR)-IR and confocal Raman microscopy to elucidate microscopic structure of creams and for the formulation design in the development of semi-solid drug products. The model creams were prepared with prednisolone (PRD) and fluconazole (FLC) as active pharmaceutical ingredients and oily solvents such as mineral oil (MO), isopropyl myristate (IPM), benzyl alcohol (BA) and diethyl sebacate (DES). As a result of microscopic ATR-IR imaging, several domains indicating oily internal phase were observed, which had absorption around 1732 and 1734 cm-1 derived from MO, IPM and DES. In addition, domains of BA around 1009 cm-1 were observed at the complemental or similar position in the formulation with MO or DES, respectively. These results suggested that the creams were oil-in-water type and the distribution of domains would reflect the compatibility of the solvents. The contents of PRD and BA were determined quantitatively in each layer after the intentional separation of the creams and the results agreed well with the imaging analysis. Whereas, confocal Raman imaging allowed to visualize the distribution of the components in depth direction as well as two-dimensional plane. In particular, the Raman imaging would ensure the coexistence of FLC and BA as oily phase in the cream. From these results, the feasibility of spectroscopic imaging techniques was successfully demonstrated for the formulation design of semi-solid dosage forms.
Asunto(s)
Crema para la Piel/análisis , Crema para la Piel/farmacología , Administración Tópica , Cosméticos , Composición de Medicamentos , Glicerol/química , Humanos , Microscopía Confocal , Miristatos/química , Crema para la Piel/administración & dosificación , Solubilidad , Solventes/química , Espectrometría RamanRESUMEN
Recently, quantitative NMR (qNMR), especially 1H-qNMR, has been widely used to determine the absolute quantitative value of organic molecules. We previously reported an optimal and reproducible sample preparation method for 1H-qNMR. In the present study, we focused on a 31P-qNMR absolute determination method. An organophosphorus compound, cyclophosphamide hydrate (CP), listed in the Japanese Pharmacopeia 17th edition was selected as the target compound, and the 31P-qNMR and 1H-qNMR results were compared under three conditions with potassium dihydrogen phosphate (KH2PO4) or O-phosphorylethanolamine (PEA) as the reference standard for 31P-qNMR and sodium 4,4-dimethyl-4-silapentanesulfonate-d6 (DSS-d6) as the standard for 1H-qNMR. Condition 1: separate sample containing CP and KH2PO4 for 31P-qNMR or CP and DSS-d6 for 1H-qNMR. Condition 2: mixed sample containing CP, DSS-d6, and KH2PO4. Condition 3: mixed sample containing CP, DSS-d6, and PEA. As conditions 1 and 3 provided good results, validation studies at multiple laboratories were further conducted. The purities of CP determined under condition 1 by 1H-qNMR at 11 laboratories and 31P-qNMR at 10 laboratories were 99.76 ± 0.43 and 99.75 ± 0.53%, respectively, and those determined under condition 3 at five laboratories were 99.66 ± 0.08 and 99.61 ± 0.53%, respectively. These data suggested that the CP purities determined by 31P-qNMR are in good agreement with those determined by the established 1H-qNMR method. Since the 31P-qNMR signals are less complicated than the 1H-qNMR signals, 31P-qNMR would be useful for the absolute quantification of compounds that do not have a simple and separate 1H-qNMR signal, such as a singlet or doublet, although further investigation with other compounds is needed.
Asunto(s)
Ciclofosfamida/análisis , Agua/análisis , Espectroscopía de Resonancia Magnética , Estructura Molecular , FósforoRESUMEN
Quantitative NMR (qNMR) is applied to determine the absolute quantitative value of analytical standards for HPLC-based quantification. We have previously reported the optimal and reproducible sample preparation method for qNMR of hygroscopic reagents, such as saikosaponin a, which is used as an analytical standard in the assay of crude drug section of Japanese Pharmacopoeia (JP). In this study, we examined the absolute purity determination of a hygroscopic substance, indocyanine green (ICG), listed in the Japanese Pharmaceutical Codex 2002, using qNMR for standardization by focusing on the adaptation of ICG to JP. The purity of ICG, as an official non-Pharmacopoeial reference standard (non-PRS), had high variation (86.12 ± 2.70%) when preparing qNMR samples under non-controlled humidity (a conventional method). Additionally, residual ethanol (0.26 ± 0.11%) was observed in the non-PRS ICG. Next, the purity of non-PRS ICG was determined via qNMR when preparing samples under controlled humidity using a saturated sodium bromide solution. The purity was 84.19 ± 0.47% with a lower variation than that under non-controlled humidity. Moreover, ethanol signal almost disappeared. We estimated that residual ethanol in non-PRS ICG was replaced with water under controlled humidity. Subsequently, qNMR analysis was performed when preparing samples under controlled humidity in a constant temperature and humidity box. It showed excellent results with the lowest variation (82.26 ± 0.19%). As the use of a constant temperature and humidity box resulted in the lowest variability, it is recommended to use the control box if the reference ICG standard is needed for JP assays.
Asunto(s)
Verde de Indocianina/análisis , Espectroscopía de Resonancia Magnética , Estructura Molecular , HumectabilidadRESUMEN
Combination tablets containing multiple active pharmaceutical ingredients (APIs) are expected to improve patient convenience by decreasing the number of tablets to be taken; thus, numerous formulations containing multiple APIs have recently been developed. To allow for dose adjustments based on patient conditions, many tablets have a bisection line to allow equal division of tablets. However, there have been no investigations regarding content uniformity among divided combination tablets. Therefore, in this study, the content uniformity of combination tablets after division was investigated using near IR and low-frequency (LF) Raman spectroscopy imaging as well as the Japanese Pharmacopoeia (JP) content uniformity tests. As model drugs, five tablets of three combination drugs containing 3-(3,4-dihydroxyphenyl)-L-alanine (L-DOPA) and benserazide hydrochloride (BNS) as APIs for treating Parkinson's disease were bisected; the resultant 10 samples were subjected to the JP content uniformity tests. We found that acceptance values of L-DOPA and BNS were 11.0-21.9% and 13.3-17.5%, respectively, with some non-conformity to the maximum allowed acceptance value (15.0%) as per the current JP. Image analyses by near IR showed that L-DOPA, BNS, lactose, and corn starch were uniformly distributed in each tablet; moreover, LF Raman spectroscopy imaging also supported the result that L-DOPA, BNS, and lactose were evenly distributed. Therefore, drug content in the tablets was uniform; thus, careful manipulation was recommended in the tablet bisection. However, the results of bisection line specifications and hardness tests revealed that the ease of division differed depending on the tablets, which warrants attention.
Asunto(s)
Antiparkinsonianos/análisis , Benserazida/análisis , Levodopa/análisis , Espectroscopía Infrarroja Corta/métodos , Espectrometría Raman/métodos , Combinación de Medicamentos , ComprimidosRESUMEN
The purpose of this study was to quantify polymorphs of active pharmaceutical ingredients in pharmaceutical tablets using a novel transmission low-frequency Raman spectroscopy method. We developed a novel transmission geometry for low-frequency Raman spectroscopy and compared quantitative ability in transmission mode versus backscattering mode using chemometrics. We prepared two series of tablets, (1) containing different weight-based contents of carbamazepine form III and (2) including different ratios of carbamazepine polymorphs (forms I/III). From the relationship between the contents of carbamazepine form III and partial least-squares (PLS) predictions in the tablets, correlation coefficients in transmission mode ( R2 = 0.98) were found to be higher than in backscattering mode ( R2 = 0.97). The root-mean-square error of cross-validation (RMSECV) of the transmission mode was 3.9 compared to 4.9 for the backscattering mode. The tablets containing a mixture of carbamazepine (I/III) polymorphs were measured by transmission low-frequency Raman spectroscopy, and it was found that the spectral shape changed according to the ratio of polymorphs: the relationship between the actual content and the prediction showed high correlation. These findings indicate that transmission low-frequency Raman spectroscopy possesses the potential to complement existing analytical methods for the quantification of polymorphs.
Asunto(s)
Carbamazepina/análisis , Polímeros/análisis , Cristalización , Estructura Molecular , Difracción de Polvo , Espectrometría Raman , Comprimidos/análisisRESUMEN
To enable the continuous production of cocrystal-containing pharmaceutical tablets, guaranteeing the cocrystal content of the final pharmaceutical tablets in the solid state is critical. This study demonstrates the quantification of caffeine-glutaric acid cocrystals in model tablets using transmission low-frequency Raman spectroscopy. Although distinguishing between cocrystals and raw materials using conventional Raman spectroscopy is difficult, the use of low-frequency Raman spectroscopy enables the discrimination of cocrystals and raw materials. Low-frequency Raman spectra were analyzed by the partial least-squares method (PLS) to obtain the predicted contents in the model tablets. To evaluate the quantitative ability of this method, the root means square error of cross-validation (RMSECV) was determined by comparing the actual concentration and predicted content with a calibration curve. For cocrystal-containing tablets, the quantitative ability of the transmission mode (RMSECV = 2.06- 3.17) was 13.4-31.4% higher than that of the backscattering mode (RMSECV= 2.37- 3.91). The coexistence of raw crystalline materials did not affect the quantitative ability for cocrystals.
Asunto(s)
Cafeína/química , Glutaratos/química , Espectrometría Raman , Comprimidos/química , Cristalización , Estructura MolecularRESUMEN
The poultice formulation is a patch containing a large amount of water. It is known that the water contained in the adhesive polymer layer (ADPL) of poultice affects the cooling sensation and skin permeability of the active pharmaceutical ingredient (API). In this study, we evaluated the relationship between the water content in a ketoprofen poultice formulation and the amount of time the poultice was left out at room temperature after removal from the airtight container, as well as the influence of the decreasing water content on the skin permeability of the API. After removing the poultice from the container for 1 h, the mass of the ADPL decreased by approximately 40%. When the near-infrared (NIR) spectrum of the ADPL of poultice was measured, the peaks reflecting the hydroxyl group were attenuated depending on the time left out at room temperature. It is suggested that the changes in the mass and NIR spectrum of the ADPL are caused by the change in the water content. Moreover, when the permeability of API was evaluated on hairless mouse skin, the cumulative skin permeation amount and flux decreased, while the lag time was prolonged as the time left out increased. These results suggest that the skin permeability of the API is impaired by water evaporation and that maintaining the water in the ADPL in poultice is very important from not only the viewpoint of cooling sensation, tackiness and moisturizing but also the skin permeability of the API.
Asunto(s)
Antiinflamatorios no Esteroideos/administración & dosificación , Antiinflamatorios no Esteroideos/química , Cetoprofeno/administración & dosificación , Cetoprofeno/química , Piel/metabolismo , Parche Transdérmico , Agua/análisis , Animales , Estabilidad de Medicamentos , Almacenaje de Medicamentos , Técnicas In Vitro , Ratones Pelados , Permeabilidad , Absorción Cutánea , TemperaturaRESUMEN
We investigated the water contents in commercial semi-solid preparations used for pressure ulcer (PU) treatment using near-IR spectroscopy (NIRS) and compared the results with those measured using the Karl Fischer (KF) method. The aim of this study was to determine a standard method and select the appropriate topical preparation with the optimal moisture for PU treatment. The water absorption properties of bases and formulations were evaluated with a time-dependent factor using Transwell as the model membrane. KF and NIRS were applicable as measurement methods of the water content in semi-solid formulations. NIRS was shown to be a useful, simple, nondestructive tool that is more advantageous than the KF method. The water absorption characteristics tested using Transwell revealed that the rate of and capacity for water absorption are determined not only by the absorption ability of the polymer base but also by other factors, such as the osmotic pressure exerted by additives. KF and NIR measurements can be used to choose external skin preparations to control the amount of water in PU treatment.
Asunto(s)
Composición de Medicamentos/métodos , Agua/química , Administración Tópica , Glicerol/química , Humanos , Pomadas/química , Pomadas/uso terapéutico , Polietilenglicoles/química , Úlcera por Presión/tratamiento farmacológico , Espectroscopía Infrarroja CortaRESUMEN
The purpose of this study was to investigate the quantification performance of transmission Raman spectroscopy with univariate analysis. Model dosage forms containing acetaminophen and an excipient, lactose monohydrate, were prepared. The Raman spectra of the tablets were obtained using the modes of transmission, backscattering micro-spectroscopy, and wide area illumination. Calibration curves for quantification of acetaminophen in the tablets were created using peak heights of the Raman spectra. Of the three modes of measurement, the quantitative results by transmission had the highest correlation with those by conventional UV-vis methods. In the validation of quantification by the transmission mode with univariate analysis, a certain degree of daily variation was confirmed. Additionally, quantitative results using peak heights were compared with those of partial least squares (PLSs) multivariate analysis. The root mean square error of prediction (RMSEP) suggested that quantification using PLS provided better precision than the peak height method as expected. However, content uniformity test using large sample sizes by the Raman spectra is not required to be very highly predictive because they usually employ non-parametric criteria and include wide specification ranges. Therefore, univariate analysis using transmission Raman spectroscopy was a suitable quantitative method for conducting content uniformity tests of large sample sizes.
Asunto(s)
Química Farmacéutica/métodos , Composición de Medicamentos , Control de Calidad , Espectrometría Raman/métodos , Acetaminofén/química , Excipientes/química , Lactosa/química , Análisis Multivariante , ComprimidosRESUMEN
The molecular states of ketoprofen and the interaction between ketoprofen and other pharmaceutical excipients in the matrix layer were examined to determine their effect on the pharmaceutical properties of original and generic ketoprofen dermal patches (generic patches A and B). Molecular states of ketoprofen were evaluated using polarized light microscopy, Raman spectroscopy and powder X-ray diffraction. For the original ketoprofen patch, crystalline components were not observed in the matrix layer. However, crystalline ketoprofen was observed in the two generic ketoprofen patches. Moreover, the ketoprofen exhibited hydrogen bonding with the pharmaceutical excipients or patch materials in the generic products. Skin permeation of ketoprofen from the patches was evaluated using hairless mouse skin. Twelve hours after application, the original patch demonstrated the highest level of cumulative skin permeation of ketoprofen. This was followed by generic patch B while generic patch A showed the lowest level of permeation. Fluxes were calculated from the skin permeation profiles. The original patch was approx. 2.4-times faster compared with generic patch A and approximately 1.9-times faster compared with generic patch B. This investigation suggested that pharmaceutical properties such as skin permeability for these types of products are affected by the precipitation of crystalline ketoprofen in the matrix layer and the interaction of ketoprofen with the pharmaceutical excipients or patch materials.
Asunto(s)
Antiinflamatorios no Esteroideos/administración & dosificación , Cetoprofeno/administración & dosificación , Parche Transdérmico , Animales , Antiinflamatorios no Esteroideos/química , Antiinflamatorios no Esteroideos/farmacocinética , Liberación de Fármacos , Cetoprofeno/química , Cetoprofeno/farmacocinética , Masculino , Ratones Pelados , Piel/metabolismo , Absorción CutáneaRESUMEN
A moisturizing cream mixed with a steroid ointment is frequently prescribed to patients suffering from atopic dermatitis. However, there is a concern that the mixing operation causes destabilization. The present study was performed to investigate the stability of such preparations closely using magnetic resonance imaging (MRI). As sample preparations, five commercial moisturizing creams that are popular in Japan were mixed with an ointment base, a white petrolatum, at a volume ratio of 1 : 1. The mixed preparations were stored at 60°C to accelerate the destabilization processes. Subsequently, the phase separations induced by the storage test were monitored using MRI. Using advanced MR technologies including spin-spin relaxation time (T2) mapping and MR spectroscopy, we successfully characterized the phase-separation behavior of the test samples. For most samples, phase separations developed by the bleeding of liquid oil components. From a sample consisting of an oil-in-water-type cream, Urepearl Cream 10%, a distinct phase-separation mode was observed, which was initiated by the aqueous component separating from the bottom part of the sample. The resultant phase separation was the most distinct among the test samples. To investigate the phase separation quantitatively and objectively, we conducted a histogram analysis on the acquired T2 maps. The water-in-oil type creams were found to be much more stable after mixing with ointment base than those of oil-in-water type creams. This finding strongly supported the validity of the mixing operation traditionally conducted in pharmacies.
Asunto(s)
Imagen por Resonancia Magnética , Bases Oleosas/análisis , Crema para la Piel/análisis , Estabilidad de Medicamentos , HumanosRESUMEN
The present study examined the stability of mixtures of various combinations of moisturizers, water in oil (w/o)-type or oil in water (o/w)-type cream preparations containing heparinoids, and steroidal ointments or creams (o/w-type) frequently used in children. Centrifugation at room temperature led to separation of mixtures of w/o-type moisturizers and steroidal ointments into three layers. Polarized microscopic observations, near-infrared (NIR) spectroscopy, and dye-based analyses revealed the presence of oily components in the upper and middle layers and water-soluble components in the lower layer. Separation into three layers upon centrifugation was also observed for mixtures of o/w-type moisturizers and steroidal ointments. In contrast, neither the o/w-type moisturizer and steroidal cream nor the w/o-type moisturizer and steroidal cream mixtures separated into layers upon centrifugation. Consideration of the characteristics of each preparation is necessary when mixing external-application dermatologic preparations. Centrifugation at 4°C did not result in layer separation of the w/o-type moisturizer and steroidal ointment mixture, suggesting that cold storage of such mixtures provides superior stability compared with room temperature storage. However, despite no obvious layer separation, the NIR spectra indicated that water movement was induced within the mixture. These results clearly indicate that methods such as NIR spectroscopy are useful for early determinations of the stability of mixed external-application dermatologic preparations.
Asunto(s)
Fármacos Dermatológicos/química , Pomadas/química , Reología , Centrifugación , Estabilidad de Medicamentos , Humanos , Aceites/química , Espectroscopía Infrarroja CortaRESUMEN
Recent active research and new regulatory guidance on pharmaceutical cocrystals have increased the rate of their development as promising approaches to improve handling, storage stability, and bioavailability of poorly soluble active pharmaceutical ingredients (APIs). However, their complex structure and the limited amount of available information related to their performance may require development strategies that differ from those of single-component crystals to ensure their clinical safety and efficacy. This article highlights current methods of characterizing pharmaceutical cocrystals and approaches to controlling their quality. Different cocrystal regulatory approaches between regions are also discussed. The physical characterization of cocrystals should include elucidating the structure of their objective crystal form as well as their possible variations (e.g., polymorphs, hydrates). Some solids may also contain crystals of individual components. Multiple processes to prepare pharmaceutical cocrystals (e.g., crystallization from solutions, grinding) vary in their applicable ingredients, scalability, and characteristics of resulting solids. The choice of the manufacturing method affects the quality control of particular cocrystals and their formulations. In vitro evaluation of the properties that govern clinical performance is attracting increasing attention in the development of pharmaceutical cocrystals. Understanding and mitigating possible factors perturbing the dissolution and/or dissolved states, including solution-mediated phase transformation (SMPT) and precipitation from supersaturated solutions, are important to ensure the bioavailability of orally administrated lower-solubility APIs. The effect of polymer excipients on the performance of APIs emphasizes the relevance of formulation design for appropriate use.