Aqueous Synthesis, Doping, and Processing of n-Type Ag2Se for High Thermoelectric Performance at Near-Room-Temperature.

Herein, we have successfully synthesized binary Ag2Se, composite Ag0:Ag2Se, and ternary Cu+:Ag2Se through an ambient aqueous-solution-based approach in a one-pot reaction at room temperature and atmospheric pressure without involving high-temperature heating, multiple-processes treatment, and organic solvents/surfactants. Effective controllability over phases and compositions/components are demonstrated with feasibility for large-scale production through an exquisite alteration in reaction parameters especially pH for enhancing and understanding thermoelectric properties. Thermoelectric ZT reaches 0.8-1.1 at near-room-temperature for n-type Ag2Se and Cu+ doping further improves to 0.9-1.2 over a temperature range of 300-393 K, which is the largest compared to that reported by wet chemistry methods. This improvement is related to the enhanced electrical conductivity and the suppressed thermal conductivity due to the incorporation of Cu+ into the lattice of Ag2Se at very low concentrations (x%Cu+:Ag2Se, x = 1.0, 1.5, and 2.0).

The effect of crystallinity on photocatalytic performance of Co3O4 water-splitting cocatalysts.

Cocatalysts, when loaded onto a water splitting photocatalyst, accelerate the gas evolution reaction and improve the efficiency of the photocatalyst. In this paper, we report that the efficiency of the photocatalyst is enhanced using an amorphous cobalt oxide cocatalyst. The WO3 film, when loaded with amorphous or nanocrystalline Co3O4, shows an improvement of up to 40% in photocurrent generation and 34% in hydrogen gas evolution. The effect of cocatalyst crystallinity on performance was systematically studied, and we found that the photocurrent deteriorates with the conversion of the cocatalyst to a highly crystalline phase at an annealing temperature of 500 °C. The mechanism of this effect was studied in detail using electrochemical impedance spectroscopy, and the enhancement effect produced by the amorphous cocatalyst is attributed to the large density of unsaturated catalytically active sites in the amorphous material.

Amorphous ruthenium nanoparticles for enhanced electrochemical water splitting.

This paper demonstrates an optimized fabrication of amorphous Ru nanoparticles through annealing at various temperatures ranging from 150 to 700 °C, which are used as water oxidation catalyst for effective electrochemical water splitting under a low overpotential of less than 300 mV. The amorphous Ru nanoparticles with short-range ordered structure exhibit an optimal and stable electrocatalytic activity after annealing at 250 °C. Interestingly, a small quantity of such Ru nanoparticles in a thin film on fluorine-doped tin oxide glass is also effectively driven by a conventional crystalline silicon solar cell that has excellent capability for harvesting visible light. Remarkably, it achieves an overall solar-to-hydrogen efficiency of 11.3% in acidic electrolyte.

Sol-gel deposited Cu2O and CuO thin films for photocatalytic water splitting.

Cu2O and CuO are attractive photocatalytic materials for water splitting due to their earth abundance and low cost. In this paper, we report the deposition of Cu2O and CuO thin films by a sol-gel spin-coating process. Sol-gel deposition has distinctive advantages such as low-cost solution processing and uniform film formation over large areas with a precise stoichiometry and thickness control. Pure-phase Cu2O and CuO films were obtained by thermal annealing at 500 °C in nitrogen and ambient air, respectively. The films were successfully incorporated as photocathodes in a photoelectrochemical (PEC) cell, achieving photocurrents of -0.28 mA cm(-2) and -0.35 mA cm(-2) (for Cu2O and CuO, respectively) at 0.05 V vs. a reversible hydrogen electrode (RHE). The Cu2O photocurrent was enhanced to -0.47 mA cm(-2) upon incorporation of a thin layer of a NiOx co-catalyst. Preliminary stability studies indicate that CuO may be more stable than Cu2O as a photocathode for PEC water-splitting.

Experimental and Numerical Study of Al2219 Powders Deposition on Al2219-T6 Substrate by Cold Spray: Effects of Spray Angle, Traverse Speed, and Standoff Distance.

Cold spray (CS) is an emerging technology for repairing and 3D additive manufacturing of a variety of metallic components using deformable metal powders. In CS deposition, gas type, gas pressure, gas temperature, and powder feed rate are the four key process parameters that have been intensively studied. Spray angle, spray gun traverse speed, and standoff distance (SoD) are the other three process parameters that have been less investigated but are also important, especially when depositing on uneven substrates or building up 3D freeform structures. Herein, the effects of spray angle, traverse speed, and SoD during CS deposition have been investigated holistically on a single material system (i.e., Al2219 powders on Al2219-T6 substrate). The coatings' mass gain, thickness, porosity, and residual stress have been characterized, and the results show that spray angle and traverse speed exercise much more effects than SoD in determining coatings' buildup. Finite element method (FEM) modeling and computational fluid dynamic (CFD) simulation have been carried out to understand the effects of these three parameters for implementing CS as repairing and additive manufacturing using aluminum-based alloy powders.

Cu(I)/Cu(II) Creutz-Taube Mixed-Valence 2D Coordination Polymers.

Graphene-like 2D coordination polymers (GCPs) have been of central research interest in recent decades with significant impact in many fields. According to classical coordination chemistry, Cu(II) can adopt the dsp2 hybridization to form square planar coordination geometry, but not Cu(I); this is why so far, there has been few 2D layered structures synthesized from Cu(I) precursors. Herein a pair of isostructural GCPs synthesized by the coordination of benzenehexathiol (BHT) ligands with Cu(I) and Cu(II) ions, respectively, is reported. Spectroscopic characterizations indicate that Cu(I) and Cu(II) coexist with a near 1:1 ratio in both GCPs but remain indistinguishable with a fractional oxidation state of +1.5 on average, making these two GCPs a unique pair of Creutz-Taube mixed-valence 2D structures. Based on density functional theory calculations, an intramolecular pseudo-redox mechanism is further uncovered whereby the radicals on BHT ligands can oxidize Cu(I) or reduce Cu(II) ions upon coordination, thus producing isostructures with distinct electron configurations. For the first time, it is demonstrated that using Cu(I) or Cu(II), one can achieve 2D isostructures, indicating an unusual fact that a neutral periodic structure can host a different number of total electrons as ground states, which may open a new chapter for 2D materials.

Synthesis and optical and electronic properties of one-dimensional sulfoxonium-based hybrid metal halide (CH3)3SOPbI3.

We report the synthesis and optical and electronic properties of a one-dimensional sulfoxonium-based hybrid metal halide in an orthorhombic crystal system with a Pnma space group. To provide direct insights, a method is developed to calculate tolerance factors with the ionic radii of non-spherical cations from X-ray crystallographic data.

Fabrication of bimetallic Cu/Au nanotubes and their sensitive, selective, reproducible and reusable electrochemical sensing of glucose.

Herein, we report a facile two-step approach to produce gold-incorporated copper (Cu/Au) nanostructures through controlled disproportionation of the Cu(+)-oleylamine complex at 220 °C to form copper nanowires and the subsequent reaction with Au(3+) at different temperatures of 140, 220 and 300 °C. In comparison with copper nanowires, these bimetallic Cu/Au nanostructures exhibit their synergistic effect to greatly enhance glucose oxidation. Among them, the shape-controlled Cu/Au nanotubes prepared at 140 °C show the highest electrocatalytic activity for non-enzymatic glucose sensing in alkaline solution. In addition to high sensitivity and fast response, the Cu/Au nanotubes possess high selectivity against interferences from other potential interfering species and excellent reproducibility with long-term stability. By introducing gold into copper nanostructures at a low level of 3, 1 and 0.1 mol% relative to the initial copper precursor, a significant electrocatalytic enhancement of the resulting bimetallic Cu/Au nanostructures starts to occur at 1 mol%. Overall, the present fabrication of stable Cu/Au nanostructures offers a promising low-cost platform for sensitive, selective, reproducible and reusable electrochemical sensing of glucose.

Effect of oxygen evolution catalysts on hematite nanorods for solar water oxidation.

Photochemical deposition of Co and Ni based oxygen evolution catalysts on hematite nanorods cathodically shifted the onset potential of photocurrent near to the flat band potential of hematite. A 9.5 fold enhancement in the photocurrent density at 0.86 V vs. RHE compared to the parent hematite photoanode was observed with the Ni-Bi/Fe(2)O(3) photoanode.