Interfacial solvation-structure regulation for stable Li metal anode by a desolvation coating technique.

Rechargeable lithium (Li) metal batteries face challenges in achieving stable cycling due to the instability of the solid electrolyte interphase (SEI). The Li-ion solvation structure and its desolvation process are crucial for the formation of a stable SEI on Li metal anodes and improving Li plating/stripping kinetics. This research introduces an interfacial desolvation coating technique to actively modulate the Li-ion solvation structure at the Li metal interface and regulate the participation of the electrolyte solvent in SEI formation. Through experimental investigations conducted using a carbonate electrolyte with limited compatibility to Li metal, the optimized desolvation coating layer, composed of 12-crown-4 ether-modified silica materials, selectively displaces strongly coordinating solvents while simultaneously enriching weakly coordinating fluorinated solvents at the Li metal/electrolyte interface. This selective desolvation and enrichment effect reduce solvent participation to SEI and thus facilitate the formation of a LiF-dominant SEI with greatly reduced organic species on the Li metal surface, as conclusively verified through various characterization techniques including XPS, quantitative NMR, operando NMR, cryo-TEM, EELS, and EDS. The interfacial desolvation coating technique enables excellent rate cycling stability (i.e., 1C) of the Li metal anode and prolonged cycling life of the Li||LiCoO2 pouch cell in the conventional carbonate electrolyte (E/C 2.6 g/Ah), with 80% capacity retention after 333 cycles.

A Randomized Controlled Clinical Trial Exploring Safety and Tolerability of Sulthiame in Sleep Apnea.

Rationale: Current therapies for obstructive sleep apnea (OSA) are limited by insufficient efficacy, compliance, or tolerability. An effective pharmacological treatment for OSA is warranted. Carbonic anhydrase inhibition has been shown to ameliorate OSA. Objectives: To explore safety and tolerability of the carbonic anhydrase inhibitor sulthiame (STM) in OSA. Methods: A 4-week double-blind, randomized, placebo-controlled dose-guiding trial was conducted in patients with moderate and/or severe OSA not tolerating positive airway pressure treatment. Measurements and Main Results: Intermittent paresthesia was reported by 79%, 67%, and 18% of patients receiving 400 mg STM (n = 34), 200 mg STM (n = 12), and placebo (n = 22), respectively. Dyspnea was reported after 400 mg STM (18%). Six patients in the higher dose group withdrew because of adverse events. There were no serious adverse events. STM reduced the apnea-hypopnea index from 55.2 to 33.0 events/h (-41.0%) in the 400-mg group and from 61.1 to 40.6 events/h (-32.1%) after 200 mg (P < 0.001 for both). Corresponding placebo values were 53.9 and 50.9 events/h (-5.4%). The apnea-hypopnea index reduction threshold of ⩾50% was reached in 40% of patients after 400 mg, 25% after 200 mg, and 5% after placebo. Mean overnight oxygen saturation improved by 1.1% after 400 and 200 mg (P < 0.001 and P = 0.034, respectively). Patient-related outcomes were unchanged. Conclusions: STM showed a satisfactory safety profile in moderate and/or severe OSA. STM reduced OSA, on average, by more than 20 events/h, one of the strongest reductions reported in a drug trial in OSA. Larger scale clinical studies of STM in OSA are justified. Clinical trial registered with www.clinicaltrialsregister.eu (2017-004767-13).

Failure Mechanisms at the Interfaces between Lithium Metal Electrodes and a Single-Ion Conducting Polymer Gel Electrolyte.

Polymer electrolytes have the potential to enable rechargeable lithium (Li) metal batteries. However, growth of nonuniform high surface area Li still occurs frequently and eventually leads to a short-circuit. In this study, a single-ion conducting polymer gel electrolyte is operated at room temperature in symmetric Li||Li cells. We use X-ray microtomography and electrochemical impedance spectroscopy (EIS) to study the cells. In separate experiments, cells were cycled at current densities of 0.1 and 0.3 mA cm-2 and short-circuits were obtained eventually after an average of approximately 240 cycles and 30 cycles, respectively. EIS reveals an initially decreasing interfacial resistance associated with electrodeposition of nonuniform Li protrusions and the concomitant increase in electrode surface area. X-ray microtomography images show that many of the nonuniform Li deposits at 0.1 mA cm-2 are related to the presence of impurities in both electrolyte and electrode phases. Protrusions are globular when they are close to electrolyte impurities but are moss-like when they appear near the impurities in the lithium metal. At long times, the interfacial resistance increases, perhaps due to additional impedance due to the formation of additional solid electrolyte interface (SEI) at the growing protrusions until the cells short. At 0.3 mA cm-2, large regions of the electrode-electrolyte interface are covered with mossy deposits. EIS reveals a decreasing interfacial resistance due to the increase in interfacial area up to short-circuit; the increase in interfacial impedance observed at the low current density is not observed. The results emphasize the importance of pure surfaces and materials on the microscopic scale and suggest that modification of interfaces and electrolyte may be necessary to enable uniform Li electrodeposition at high current densities.

Ceramic-in-Polymer Hybrid Electrolytes with Enhanced Electrochemical Performance.

Polymer electrolytes are attractive candidates to boost the application of rechargeable lithium metal batteries. Single-ion conducting polymers may reduce polarization and lithium dendrite growth, though these materials could be mechanically overly rigid, thus requiring ion mobilizers such as organic solvents to foster transport of Li ions. An inhomogeneous mobilizer distribution and occurrence of preferential Li transport pathways eventually yield favored spots for Li plating, thereby imposing additional mechanical stress and even premature cell short circuits. In this work, we explored ceramic-in-polymer hybrid electrolytes consisting of polymer blends of single-ion conducting polymer and PVdF-HFP, including EC/PC as swelling agents and silane-functionalized LATP particles. The hybrid electrolyte features an oxide-rich layer that notably stabilizes the interphase toward Li metal, enabling single-side lithium deposition for over 700 h at a current density of 0.1 mA cm-2. The incorporated oxide particles significantly reduce the natural solvent uptake from 140 to 38 wt % despite maintaining reasonably high ionic conductivities. Its electrochemical performance was evaluated in LiNi0.6Co0.2Mn0.2O2 (NMC622)||Li metal cells, exhibiting impressive capacity retention over 300 cycles. Notably, very thin LiNbO3 coating of the cathode material further boosts the cycling stability, resulting in an overall capacity retention of 78% over more than 600 cycles, clearly highlighting the potential of hybrid electrolyte concepts.