RESUMEN
An all-fiber high-power erbium-doped fiber laser (EDFL) source generating optical pulses from 200 µs to 5 ms with a stable rectangular envelope for fractional photo-rejuvenation is proposed and experimentally demonstrated. A master oscillator power amplifier (MOPA) configuration composed of a master oscillator, an acousto-optic modulator (AOM), and a one-stage amplifier is designed and employed in the EDFL to serve as an efficient laser system with excellent output performance. To avoid multistage amplifiers, the master oscillator generates 1.5 W, and a Yb-free Er-doped large-mode-area (LMA) active fiber is used for a one-stage power amplifier. There are two benefits to this approach: first, modulation of both pump and seed pulses is used to achieve clear rectangular shaped pulses without amplified spontaneous emission (ASE) growth; and second, there are no power limitations in the amplifier and undesirable 1 µm ASE compared to Er/Yb systems. We have reached 28.6 W of peak power with 26% slope efficiency limited only by available pump power, so the system can be easily scaled for achieving a higher peak power.
RESUMEN
In this Letter, we propose and realize a novel concept for a high-peak-power highly efficient fiber amplifier in the 1.55 µm spectral range. The amplifier is based on the simultaneous utilization of Er-doped, Yb-free, and Er-Yb codoped large-mode-area fibers spliced together. Using this approach, we demonstrate the amplification of single-frequency 160 ns pulses at 1554 nm to a peak power of 3.7 kW with a pump-to-signal conversion efficiency of 23.6% relative to the launched multimode pump power at 976 nm.
RESUMEN
We show both experimentally and theoretically a method to increase the stimulated Brillouin scattering (SBS) threshold and output power of narrow linewidth fiber Raman amplifiers. This method employs two or more fibers with varying concentrations of the Raman gain material dopant such as GeO2 or P2O5 in silicate-based glasses. These fibers are then cascaded to form an amplifier gain stage, disrupting the buildup of SBS that normally occurs in single continuous fibers. The numerical model shown is applicable to arbitrary amplifier systems for gain stage optimization and increased power scaling. We give experimental results for phosphosilicate fibers that agree well with simulation predictions that support the numerical model used.
RESUMEN
Optimization of Yb-free Er-doped fiber for lasers and amplifiers cladding pumped at 976 nm was performed in this Letter. The single-mode fiber design includes an increased core diameter of 34 µm and properly chosen erbium and co-dopant concentrations. We demonstrate an all-fiber high power laser and power amplifier based on this fiber with the record slope efficiency of 40%. To the best of our knowledge, the achieved output power of 75 W is the highest power reported for such lasers.
Asunto(s)
Erbio , Rayos Láser , Fibras ÓpticasRESUMEN
Direct amplification of output from chirped pulse oscillator (CPO) to 3.3 W of average power (pulse energy of 118 nJ in 20 ps pulse duration before compression) was achieved in a properly designed cladding pumped large mode area Er-doped fiber. Various configurations of CPO cavity with different FWHM of output spectrum and pulse duration were investigated. Fourier limit compression with 480 fs pulse duration and 32 kW peak power has been obtained for pulses with 14.8 nm FWHM spectrum. Subsequent nonlinear compression in a standard SMF-28 fiber yielded pulses as short as 145 fs.
RESUMEN
Very large-mode-area Yb(3+)-doped single-mode photonic bandgap (PBG) Bragg fiber oscillators are considered. The transverse hole-burning effect is numerically modeled, which helps properly design the PBG cladding and the Yb(3+)-doped region for the high-order mode content to be carefully controlled. A ratio of the Yb(3+)-doped region diameter to the overall core diameter of 40% allows for single-mode emission, even for small spool diameters of 15 cm. Such a fiber was manufactured and subsequently used as the core element of a cw oscillator. Very good beam quality parameter M(2)=1.12 and slope efficiency of 80% were measured. Insensitivity to bending, exemplified by the absence of temporal drift of the beam, was demonstrated for curvature diameter as small as 15 cm.
RESUMEN
We describe the design and characterization of solid core large mode area bandgap fibers exhibiting low propagation loss and low bend loss. The fibers have been prepared by modified chemical vapor deposition process. The bandgap guidance obtained thanks to a 3-bilayer periodic cladding is assisted by a very slight index step (5.10-4) in the solid core. The propagation loss reaches a few dB/km and is found to be close to material loss.
RESUMEN
It is found that the reflection of leaky radiation from the interface between the outer silica cladding and the coating polymer greatly modifies the loss spectrum of Bragg fibers. A simple model that describes this effect is proposed and confirmed by measurement and computation.
RESUMEN
Four-wave mixing (FWM) in nonlinear germanosilicate fibers with GeO2 concentrations as high as 67 mol.% in the core is studied theoretically and experimentally. Large frequency shifts of 1875-3829 cm(-1) are observed in the mixed-mode pump parametric process. The dependence of FWM phase matching on the GeO2 concentration, core diameter, and index profile is demonstrated. The 2.5% conversion efficiency of an 887 nm signal to a 1.3 microm communication band is obtained at a 2 W cw pump power inside the fiber.