Characterizing Volatile Emissions and Combustion Byproducts from Aqueous Film-Forming Foams Using Online Chemical Ionization Mass Spectrometry.

Aqueous film-forming foams (AFFFs) are used in firefighting applications and often contain per- and polyfluoroalkyl substances (PFAS), which can detrimentally impact environmental and biological health. Incineration is a potential disposal method for AFFFs, which may produce secondary PFAS and other air pollutants. We used online chemical ionization mass spectrometry (CIMS) to measure volatile PFAS emissions from incinerating AFFF concentrate solutions. We quantified perfluorinated carboxylic acids (PFCAs) during the incineration of legacy and contemporary AFFFs. These included trifluoroacetic acid, which reached mg m-3 quantities in the incinerator exhaust. These PFCAs likely arose as products of incomplete combustion of AFFF fluorosurfactants with lower peak furnace temperatures yielding higher PFCA concentrations. We also detected other short-chain PFAS, and other novel chemical products in AFFF combustion emissions. The volatile headspace above AFFF solutions contained larger (C ≥ 8), less oxidized PFAS detected by CIMS. We identified neutral PFAS resembling fluorotelomer surfactants (e.g., fluorotelomer sulfonamide alkylbetaines and fluorotelomer thioether amido sulfonates) and fluorotelomer alcohols in contemporary AFFF headspaces. Directly comparing the distinct chemical spaces of AFFF volatile headspace and combustion byproducts as measured by CIMS provides insight toward the chemistry of PFAS during thermal treatment of AFFFs.

Particulate Formation from a Copper Oxide-Based Oxygen Carrier in Chemical Looping Combustion for CO2 Capture.

Attrition behavior and particle loss of a copper oxide-based oxygen carrier from a methane chemical looping combustion (CLC) process was investigated in a fluidized bed reactor. The aerodynamic diameters of most elutriated particulates, after passing through a horizontal settling duct, range between 2 and 5 µm. A notable number of submicrometer particulates are also identified. Oxygen carrier attrition was observed to lead to increased CuO loss resulting from the chemical looping reactions, i.e., Cu is enriched in small particles generated primarily from fragmentation in the size range of 10-75 µm. Cyclic reduction and oxidation reactions in CLC have been determined to weaken the oxygen carrier particles, resulting in increased particulate emission rates when compared to those of oxygen carriers without redox reactions. The generation rate for particulates <10 µm was found to decrease with progressive cycles over as-prepared oxygen carrier particles and then reach a steady state. The surface of the oxygen carrier is also found to be coarsened due to a Kirkendall effect, which also explains the enrichment of Cu on particle surfaces and in small particles.

Characterization of Size-Fractionated Airborne Particles Inside an Electronic Waste Recycling Facility and Acute Toxicity Testing in Mice.

Disposal of electronic waste (e-waste) in landfills, incinerators, or at rudimentary recycling sites can lead to the release of toxic chemicals into the environment and increased health risks. Developing e-waste recycling technologies at commercial facilities can reduce the release of toxic chemicals and efficiently recover valuable materials. While these e-waste operations represent a vast improvement over previous approaches, little is known about environmental releases, workplace exposures, and potential health impacts. In this study, airborne particulate matter (PM) was measured at various locations within a modern U.S.-based e-waste recycling facility that utilized mechanical processing. In addition, composite size fractionated PM (coarse, fine and ultrafine) samples were collected, extracted, chemically analyzed, and given by oropharyngeal aspiration to mice or cultured with lung slices for lung toxicity tests. Indoor total PM concentrations measured during the study ranged from 220 to 1200 µg/m(3). In general, the coarse PM (2.5-10 µm) was 3-4 times more abundant than fine/ultrafine PM (<2.5 µm). The coarse PM contained higher levels of Ni, Pb, and Zn (up to 6.8 times) compared to the fine (0.1-2.5 µm) and ultrafine (<0.1 µm) PM. Compared to coarse PM measurements from a regional near-roadway study, Pb and Ni were enriched 170 and 20 times, respectively, in the indoor PM, with other significant enrichments (>10 times) observed for Zn and Sb, modest enrichments (>5 times) for Cu and Sr, and minor enrichments (>2 times) for Cr, Cd, Mn, Ca, Fe, and Ba. Negligible enrichment (<2 times) or depletion (<1 time) were observed for Al, Mg, Ti, Si, and V. The coarse PM fraction elicited significant pro-inflammatory responses in the mouse lung at 24 h postexposure compared to the fine and ultrafine PM, and similar toxicity outcomes were observed in the lung slice model. We conclude that exposure to coarse PM from the facility caused substantial inflammation in the mouse lung and enrichment of these metals compared to levels normally present in the ambient PM could be of potential health concern.

Generation and characterization of diesel engine combustion emissions from petroleum diesel and soybean biodiesel fuels and application for inhalation exposure studies.

Biodiesel made from the transesterification of plant- and animal-derived oils is an important alternative fuel source for diesel engines. Although numerous studies have reported health effects associated with petroleum diesel emissions, information on biodiesel emissions are more limited. To this end, a program at the U.S. EPA assessed health effects of biodiesel emissions in rodent inhalation models. Commercially obtained soybean biodiesel (B100) and a 20% blend with petroleum diesel (B20) were compared to pure petroleum diesel (B0). Rats and mice were exposed independently for 4 h/day, 5 days/week for up to 6 weeks. Exposures were controlled by dilution air to obtain low (50 µg/m(3)), medium (150 µg/m(3)) and high (500 µg/m(3)) diesel particulate mass (PM) concentrations, and compared to filtered air. This article provides details on facilities, fuels, operating conditions, emission factors and physico-chemical characteristics of the emissions used for inhalation exposures and in vitro studies. Initial engine exhaust PM concentrations for the B100 fuel (19.7 ± 0.7 mg/m(3)) were 30% lower than those of the B0 fuel (28.0 ± 1.5 mg/m(3)). When emissions were diluted with air to control equivalent PM mass concentrations, B0 exposures had higher CO and slightly lower NO concentrations than B100. Organic/elemental carbon ratios and oxygenated methyl esters and organic acids were higher for the B100 than B0. Both the B0 and B100 fuels produced unimodal-accumulation mode particle-size distributions, with B0 producing lower concentrations of slightly larger particles. Subsequent papers in this series will describe the effects of these atmospheres on cardiopulmonary responses and in vitro genotoxicity studies.

Health effects of soy-biodiesel emissions: bioassay-directed fractionation for mutagenicity.

CONTEXT: Soy biodiesel is the predominant biodiesel in the USA, but there is little understanding of the classes of chemicals responsible for the mutagenicity of its emissions. OBJECTIVE: We determined some of the chemical classes responsible for the mutagenicity of the particulate matter (PM) of the emissions from petroleum diesel (B0) and biodiesel containing increasing concentrations of soy methyl esters (B20, B50, and B100). MATERIALS AND METHODS: We subjected organic extracts of the PM to bioassay-directed fractionation by sequential elution on silica gel with solvents of increasing polarity to produce four fractions per fuel. We injected these onto high performance liquid chromatography to produce 62 sub-fractions per fraction based on chemical polarity and evaluated all fractions and sub-fractions for mutagenicity in Salmonella. We correlated the results with the concentrations of 32 polycyclic aromatic hydrocarbons (PAHs) in the fractions. RESULTS: The mutagenicity-emission factors of the fractions generally decreased with increasing concentrations of soy in the fuel. Despite the different chemical compositions of the fuels, the extractable organics of all four emissions had similar features: ∼60% of the mass was nonpolar, non-mutagenic compounds; most of the PAHs were polar; and most of the mutagenicity was due to weakly polar and polar compounds. Some of the mutagenicity of B20 was due to highly polar compounds. CONCLUSIONS: The PM from soy biodiesel emissions was less mutagenic than that from petroleum diesel, and this reduction was associated with reduced concentrations of various weakly polar, polar, and highly polar mutagens, including PAHs, aromatic amines, nitroarenes, and oxy-PAHs.

Health effects of soy-biodiesel emissions: mutagenicity-emission factors.

CONTEXT: Soy biodiesel is the predominant biodiesel fuel used in the USA, but only a few, frequently conflicting studies have examined the potential health effects of its emissions. OBJECTIVE: We combusted petroleum diesel (B0) and fuels with increasing percentages of soy methyl esters (B20, B50 and B100) and determined the mutagenicity-emission factors expressed as revertants/megajoule of thermal energy consumed (rev/MJ(th)). MATERIALS AND METHODS: We combusted each fuel in replicate in a small (4.3-kW) diesel engine without emission controls at a constant load, extracted organics from the particles with dichloromethane, determined the percentage of extractable organic material (EOM), and evaluated these extracts for mutagenicity in 16 strains/S9 combinations of Salmonella. RESULTS: Mutagenic potencies of the EOM did not differ significantly between replicate experiments for B0 and B100 but did for B20 and B50. B0 had the highest rev/MJ(th), and those of B20 and B100 were 50% and ∼85% lower, respectively, in strains that detect mutagenicity due to polycyclic aromatic hydrocarbons (PAHs), nitroarenes, aromatic amines or oxidative mutagens. For all strains, the rev/MJ(th) decreased with increasing biodiesel in the fuel. The emission factor for the 16 EPA Priority PAHs correlated strongly (r(2 )= 0.69) with the mutagenicity-emission factor in strain TA100 + S9, which detects PAHs. CONCLUSIONS: Under a constant load, soy-biodiesel emissions were 50-85% less mutagenic than those of petroleum diesel. Without additional emission controls, petroleum and biodiesel fuels had mutagenicity-emission factors between those of large utility-scale combustors (e.g. natural gas, coal, or oil) and inefficient open-burning (e.g. residential wood fireplaces).

Review of per- and poly-fluoroalkyl treatment in combustion-based thermal waste systems in the United States.

Per- and poly-fluoroalkyl substances (PFAS) are a class of synthetic chemicals known for their widespread presence and environmental persistence. Carbon-fluorine (C-F) bonds are major components among PFAS and among the strongest organic bonds, thus destroying PFAS may present significant challenge. Thermal treatment such as incineration is an effective and approved method for destroying many halogenated organic chemicals. Here, we present the results of existing studies and testing at combustion-based thermal treatment facilities and summarize what is known regarding PFAS destruction and mineralization at such units. Available results suggest the temperature and residence times reached by some thermal treatment systems are generally favorable to the destruction of PFAS, but the possibility for PFAS or fluorinated organic byproducts to escape destruction and adequate mineralization and be released into the air cannot be ruled out. Few studies have been conducted at full-scale operating facilities, and none to date have attempted to characterize possible fluorinated organic products of incomplete combustion (PICs). Further, the ability of existing air pollution control (APC) systems, designed primarily for particulate and acid gas control, to reduce PFAS air emissions has not been determined. These data gaps remain primarily due to the previous lack of available methods to characterize PFAS destruction and PIC concentrations in facility air emissions. However, newly developed stack testing methods offer an improved understanding of the extent to which thermal waste treatment technologies successfully destroy and mineralize PFAS in these waste streams.

A critical review of perfluoroalkyl and polyfluoroalkyl substances (PFAS) landfill disposal in the United States.

Landfills manage materials containing per- and polyfluoroalkyl substances (PFAS) from municipal solid waste (MSW) and other waste streams. This manuscript summarizes state and federal initiatives and critically reviews peer-reviewed literature to define best practices for managing these wastes and identify data gaps to guide future research. The objective is to inform stakeholders about waste-derived PFAS disposed of in landfills, PFAS emissions, and the potential for related environmental impacts. Furthermore, this document highlights data gaps and uncertainties concerning the fate of PFAS during landfill disposal. Most studies on this topic measured PFAS in liquid landfill effluent (leachate); comparatively fewer have attempted to estimate PFAS loading in landfills or other effluent streams such as landfill gas (LFG). In all media, the reported total PFAS heavily depends on waste types and the number of PFAS included in the analytical method. Early studies which only measured a small number of PFAS, predominantly perfluoroalkyl acids (PFAAs), likely report a significant underestimation of total PFAS. Major findings include relationships between PFAS effluent and landfill conditions - biodegradable waste increases PFAS transformation and leaching. Based on the results of multiple studies, it is estimated that 84% of PFAS loading to MSW landfills (7.2 T total) remains in the waste mass, while 5% leaves via LFG and 11% via leachate on an annual basis. The environmental impact of landfill-derived PFAS has been well-documented. Additional research is needed on PFAS in landfilled construction and demolition debris, hazardous, and industrial waste in the US.

Characterization of PFAS air emissions from thermal application of fluoropolymer dispersions on fabrics.

During thermal processes utilized in affixing fluoropolymer coatings dispersion to fibers and fabrics, coating components are vaporized. It is suspected that per- and polyfluoroalkyl substances (PFAS) from the dispersions may undergo chemical transformations at the temperatures used, leading to additional emitted PFAS thermal byproducts. It is important to characterize these emissions to support evaluation of the resulting environmental and health impacts. In this study, a bench-scale system was built to simulate this industrial process via thermal application of dispersions to fiberglass utilizing relevant temperatures and residence times in sequential drying, baking, and sintering steps. Experiments were performed with two commercially available dispersions and a simple model mixture containing a single PFAS (6:2 fluorotelomer alcohol [6:2 FTOH]). Vapor-phase emissions were sampled and characterized by several off-line and real-time mass spectrometry techniques for targeted and nontargeted PFAS. Results indicate that multiple PFAS thermal transformation products and multiple nonhalogenated organic species were emitted from the exit of the high temperature third (sintering) furnace when 6:2 FTOH was the only PFAS present in the aqueous mixture. This finding supports the hypothesis that temperatures typical of these industrial furnaces may also induce chemical transformations within the fluorinated air emissions. Experiments using the two commercial fluoropolymer dispersions indicate air emissions of part-per-million by volume (ppmv) concentrations of heptafluoropropyl-1,2,2,2-tetrafluoroethyl ether (Fluoroether E1), as well as other PFAS at operationally relevant temperatures. We suspect that E1 is a direct thermal decomposition product (via decarboxylation) of 2,3,3,3-tetrafluoro-2-(heptafluoropropoxy)propanoic acid (commonly referred to as HFPO-DA) present in the dispersions. Other thermal decomposition products, including the monomer, tetrafluoroethene, may originate from the PFAS used to stabilize the dispersion or from the polymer particles in suspension. This study represents the first researcher-built coating application simulator to report nontargeted PFAS emission characterization, real-time analyses, and the quantification of 30 volatile target PFAS.Implications: Thermal processes used to affix fluoropolymers to fabrics are believed to be a source of PFAS air emissions. These coating operations are used by many large and small manufacturers and typically do not currently require any air emissions control. This research designed and constructed a bench-scale system that simulates these processes and used several off-line and advanced real-time mass spectroscopy techniques to characterize PFAS air emissions from two commercial fluoropolymer dispersions. Further, as the compositions of commercial dispersions are largely unknown, a model three-component solution containing a single PFAS was used to characterize emissions of multiple PFAS thermal transformation products at operationally relevant conditions. This research shows that fluoropolymer fabric coating facilities can be sources of complex mixtures of PFAS air emissions that include volatile and semivolatile PFAS present in the dispersions, as well as PFAS byproducts formed by the thermal transformation of fluorocarbon and hydrocarbon species present in these dispersions.

Mutagenicity and carcinogenicity of combustion emissions are impacted more by combustor technology than by fuel composition: A brief review.

Studies during the past 50 years have characterized the carcinogenicity and mutagenicity of extractable organic material (EOM) of particulate matter (PM) in ambient air and from combustion emissions. We have summarized conclusions from these studies and present data supporting those conclusions for 50 combustion emissions, including carcinogenic potencies on mouse skin (papillomas/mouse/mg EOM), mutagenic potencies (revertants/µg EOM) in the Salmonella (Ames) mutagenicity assay, and mutagenicity emission factors (revertants/kg fuel or revertants/MJthermal ) in Salmonella. Mutagenic potencies of EOM from PM in ambient air and combustion emissions span 1-2 orders of magnitude, respectively. In contrast, the revertants/m3 span >5 orders of magnitude due to variable PM concentrations in ambient air. Carcinogenic potencies of EOM from combustion emissions on mouse skin and EOM-associated human lung cancer risk from those emissions both span ~3 orders of magnitude and are highly associated. The ubiquitous presence of polycyclic aromatic hydrocarbons (PAHs), nitroarenes, and aromatic amines results in mutagenic and carcinogenic potencies of PM that span only 1-3 orders of magnitude; most PM induces primarily G to T mutations. Mutagenicity emission factors of combustion emissions span 3-5 orders of magnitude and correlate with PAH emission factors (r > 0.9). Mutagenicity emission factors were largely a function of how material was burned (highly efficient modern combustors versus open burning) rather than what materials were burned. Combustion systems that minimize kinetic and mass-transfer limitations and promote complete oxidation also minimize the mutagenicity of their emissions. This fundamental engineering principle can inform environmental and public health assessments of combustion emissions.

Combustion of C1 and C2 PFAS: Kinetic modeling and experiments.

A combustion model, originally developed to simulate the destruction of chemical warfare agents, was modified to include C1-C3 fluorinated organic reactions and kinetics compiled by the National Institute of Standards and Technology (NIST). A simplified plug flow reactor version of this model was used to predict the destruction efficiency (DE) and formation of products of incomplete combustion (PICs) for three C1 and C2 per- and poly-fluorinated alkyl substances (PFAS) (CF4, CHF3, and C2F6) and compare predicted values to Fourier Transform Infrared spectroscopy (FTIR)-based measurements made from a pilot-scale EPA research combustor (40-64 kW, natural gas-fired, 20% excess air). PFAS were introduced through the flame, and at post-flame locations along a time-temperature profile allowing for simulation of direct flame and non-flame injection, and examination of the sensitivity of PFAS destruction on temperature and free radical flame chemistry. Results indicate that CF4 is particularly difficult to destroy with DEs ranging from ~60 to 95% when introduced through the flame at increasing furnace loads. Due to the presence of lower energy C-H and C-C bonds to initiate molecular dissociation reactions, CHF3 and C2F6 were easier to destroy, exhibiting DEs >99% even when introduced post-flame. However, these lower bond energies may also lead to the formation of CF2 and CF3 radicals at thermal conditions unable to fully de-fluorinate these species and formation of fluorinated PICs. DEs determined by the model agreed well with the measurements for CHF3 and C2F6 but overpredicted DEs at high temperatures and underpredicted DEs at low temperatures for CF4. However, high DEs do not necessarily mean absence of PICs, with both model predictions and limited FTIR measurements indicating the presence of similar fluorinated PICs in the combustion emissions. The FTIR was able to provide real-time emission measurements and additional model development may improve prediction of PFAS destruction and PIC formation.Implications: The widespread use of PFAS for over 70 years has led to their presence in multiple environmental matrixes including human tissues. While the chemical and thermal stability of PFAS are related to their desirable properties, this stability means that PFAS are very slow to degrade naturally and potentially difficult to destroy completely through thermal treatment processes often used for organic waste destruction. In this applied combustion study, model PFAS compounds were introduced to a pilot-scale EPA research furnace. Real-time FTIR measurements were performed of the injected compound and trace products of incomplete combustion (PICs) at operationally relevant conditions, and the results were successfully compared to kinetic model predictions of those same PFAS destruction efficiencies and trace gas-phase PIC constituents. This study represents a significant potential enhancement in available tools to support effective management of PFAS-containing wastes.

Low Temperature Thermal Treatment of Gas-Phase Fluorotelomer Alcohols by Calcium Oxide.

Given the extent to which per- and polyfluoroalkyl substances (PFAS) are used in commercial and industrial applications, the need to evaluate treatment options that reduce environmental emissions and human and ecological exposures of PFAS is becoming more necessary. One specific chemical class of PFAS, fluorotelomer alcohols (FTOHs), have vapor pressures such that a significant fraction is expected to be present in the gas-phase even at ambient temperatures. FTOHs are used in a variety of PFAS applications, including synthesis and material coatings. Using two complementary mass spectrometric methods, the use of calcium oxide (CaO) was examined as a low temperature and potentially low-cost thermal treatment media for removal and destruction of four gas-phase FTOHs of varying molecular weights. This was accomplished by assessing the removal/destruction efficiency of the FTOHs and the formation of fluorinated byproducts as a function of treatment temperature (200 - 800 °C) in the presence of CaO compared to thermal-only destruction. During the treatment process, there is evidence that other PFAS compounds are produced at low temperatures (200 - 600 °C) as the primary FTOH partially degrades. At temperatures above 600 °C, thermal treatment with CaO prevented the formation or removed nearly all these secondary products.

Differential transcriptional regulation of IL-8 expression by human airway epithelial cells exposed to diesel exhaust particles.

Exposure to diesel exhaust particles (DEP) induces inflammatory signaling characterized by MAP kinase-mediated activation of NFkB and AP-1 in vitro and in bronchial biopsies obtained from human subjects exposed to DEP. NFkB and AP-1 activation results in the upregulation of genes involved in promoting inflammation in airway epithelial cells, a principal target of inhaled DEP. IL-8 is a proinflammatory chemokine expressed by the airway epithelium in response to environmental pollutants. The mechanism by which DEP exposure induces IL-8 expression is not well understood. In the current study, we sought to determine whether DEP with varying organic content induces IL-8 expression in lung epithelial cells, as well as, to develop a method to rapidly evaluate the upstream mechanism(s) by which DEP induces IL-8 expression. Exposure to DEP with varying organic content differentially induced IL-8 expression and IL-8 promoter activity human airway epithelial cells. Mutational analysis of the IL-8 promoter was also performed using recombinant human cell lines expressing reporters linked to the mutated promoters. Treatment with a low organic-containing DEP stimulated IL-8 expression by a mechanism that is predominantly NFkB-dependent. In contrast, exposure to high organic-containing DEP induced IL-8 expression independently of NFkB through a mechanism that requires AP-1 activity. Our study reveals that exposure to DEP of varying organic content induces proinflammatory gene expression through multiple specific mechanisms in human airway epithelial cells. The approaches used in the present study demonstrate the utility of a promoter-reporter assay ensemble for identifying transcriptional pathways activated by pollutant exposure.

Role of oxidative stress on diesel-enhanced influenza infection in mice.

Numerous studies have shown that air pollutants, including diesel exhaust (DE), reduce host defenses, resulting in decreased resistance to respiratory infections. This study sought to determine if DE exposure could affect the severity of an ongoing influenza infection in mice, and examine if this could be modulated with antioxidants. BALB/c mice were treated by oropharyngeal aspiration with 50 plaque forming units of influenza A/HongKong/8/68 and immediately exposed to air or 0.5 mg/m3 DE (4 hrs/day, 14 days). Mice were necropsied on days 1, 4, 8 and 14 post-infection and lungs were assessed for virus titers, lung inflammation, immune cytokine expression and pulmonary responsiveness (PR) to inhaled methacholine. Exposure to DE during the course of infection caused an increase in viral titers at days 4 and 8 post-infection, which was associated with increased neutrophils and protein in the BAL, and an early increase in PR. Increased virus load was not caused by decreased interferon levels, since IFN-ß levels were enhanced in these mice. Expression and production of IL-4 was significantly increased on day 1 and 4 p.i. while expression of the Th1 cytokines, IFN-γ and IL-12p40 was decreased. Treatment with the antioxidant N-acetylcysteine did not affect diesel-enhanced virus titers but blocked the DE-induced changes in cytokine profiles and lung inflammation. We conclude that exposure to DE during an influenza infection polarizes the local immune responses to an IL-4 dominated profile in association with increased viral disease, and some aspects of this effect can be reversed with antioxidants.

Chemistry of Trace Inorganic Elements in Coal Combustion Systems: A Century of Discovery.

Coal fueled the Industrial Revolution and the global expansion of electrification in the 20th century. In the 21st century, coal use has declined in North America and Europe, but continues to increase in Asia. Coal contains many of the elements of the Periodic Table, in percent-levels or in trace amounts (ppm, ppb). The impact of many of these elements on the environment via air and water discharges from coal-fired plants has been studied with decades of research on their chemical transformations within combustion systems and on their fates upon reintroduction into the environment. The transformations of the trace elements present in coal burned during combustion can be categorized as thermal volatilizations from the coal in the furnace; thermal decomposition of trace element compounds inside the coal; encapsulation inside ash structures through high-temperature vitrification; oxidation of the trace elements with the myriad species contained in flue gas through gas phase (homogeneous) reactions or catalytic (gas-solid) reactions; adsorption and/or reactions with active sites on entrained fly ash particulates contained in the flue gas; and absorption into solutions. These transformations can, in many cases, impact the fraction of these trace elements that are removed by various pollution control devices compared to the fraction released into the environment. The sampling and measurement of trace elements, in the inlet coal, outlet flue gas, aqueous scrubber solutions, and ash matrices, represents a significant challenge. This review focuses on the behavior of trace elements in industrial coal combustion systems with an emphasis on what has been learned over the past century uniquely related to the use of coal in boilers for electricity and heat production. Key accomplishments in measurement, modeling and control of trace element emissions in coal-fired systems are highlighted.

One-month diesel exhaust inhalation produces hypertensive gene expression pattern in healthy rats.

BACKGROUND: Exposure to diesel exhaust (DE) is linked to vasoconstriction, endothelial dysfunction, and myocardial ischemia in compromised individuals. OBJECTIVE: We hypothesized that DE inhalation would cause greater inflammation, hematologic alterations, and cardiac molecular impairment in spontaneously hypertensive (SH) rats than in healthy Wistar Kyoto (WKY) rats. METHODS AND RESULTS: Male rats (12-14 weeks of age) were exposed to air or DE from a 30-kW Deutz engine at 500 or 2,000 microg/m3, 4 hr/day, 5 days/week for 4 weeks. Neutrophilic influx was noted in the lung lavage fluid of both strains, but injury markers were minimally changed. Particle-laden macrophages were apparent histologically in DE-exposed rats. Lower baseline cardiac anti-oxidant enzyme activities were present in SH than in WKY rats; however, no DE effects were noted. Cardiac mitochondrial aconitase activity decreased after DE exposure in both strains. Electron microscopy indicated abnormalities in cardiac mitochondria of control SH but no DE effects. Gene expression profiling demonstrated alterations in 377 genes by DE in WKY but none in SH rats. The direction of DE-induced changes in WKY mimicked expression pattern of control SH rats without DE. Most genes affected by DE were down-regulated in WKY. The same genes were down-regulated in SH without DE producing a hypertensive-like expression pattern. The down-regulated genes included those that regulate compensatory response, matrix metabolism, mitochondrial function, and oxidative stress response. No up-regulation of inflammatory genes was noted. CONCLUSIONS: We provide the evidence that DE inhalation produces a hypertensive-like cardiac gene expression pattern associated with mitochondrial oxidative stress in healthy rats.

Electrophilic and redox properties of diesel exhaust particles.

The adverse health effects of air pollutants have been associated with their redox and electrophilic properties. Although the specific chemical species involved in these effects are not known, the characterization of their general physical and chemical properties is important to our understanding of the mechanisms by which they cause health problems. This manuscript describes results of a study examining the partition properties of these activities in aqueous and organic media. The water and dichloromethane (DCM) solubility of redox active and electrophilic constituents of seven diesel exhaust particle (DEP) samples were determined with assays developed earlier in this laboratory. The constituents exhibiting redox activity, which included both metals and nonmetal species, were associated with the particles in the aqueous suspensions. Portions of the redox active compounds were also DCM-soluble. In contrast, the electrophilic constituents included both water-soluble and DCM-soluble species. The role of quinones or quinone-like compounds in redox and electrophilic activities of the DCM-soluble constituents was assessed by reductive acetylation, a procedure that inactivates quinones. The results from this experiment indicated that most of the activities in the organic extract were associated with quinone-like substances. The partition properties of the reactive species are important in exposure assessment since the toxicokinetics of particles and solutes are quite distinct.

Mutagenicity emission factors of canola oil and waste vegetable oil biodiesel: Comparison to soy biodiesel.

Canola (or rapeseed) oil and waste vegetable oil (WVO) are used commonly to make biodiesel fuels composed completely from these oils (B100) or as blends with petroleum diesel (B0). However, no studies have reported the mutagenic potencies of the particulate matter with diameter ≤2.5 µm (PM2.5) or the mutagenicity emission factors, such as revertants/MJthermal (rev/MJth) for these biodiesel emissions. Using strains TA98 and TA100 with the Salmonella (Ames) mutagenicity assay, we determined these metrics for organic extracts of PM2.5 of emissions from biodiesel containing 5% soy oil (soy B5); 5, 20, 50, and 100% canola (canola B5, B20, B50, B100), and 100% waste vegetable oil (WVO B100). The mutagenic potencies (rev/mg PM2.5) of the canola B100 and WVO B100 emissions were generally greater than those of B0, whereas the mutagenicity emission factors (rev/MJth, rev/kg fuel, and rev/m3) were less, reflecting the lower PM emissions of the biodiesels relative to B0. Nearly all the rev/mg PM2.5 and rev/MJth values were greater in TA98 with S9 than without S9, indicating a relatively greater role for polycyclic aromatic hydrocarbons, which require S9, than nitroarenes, which do not. In TA100 -S9, the rev/mg PM2.5 and rev/MJth for the biodiesels were generally ≥ to those of B0, indicating that most of these biodiesels produced more direct-acting, base-substitution mutagenic activity than did B0. For B100 biodiesels and petroleum diesel, the rev/MJth in TA98 + S9 ranked: petroleum diesel > canola > WVO > soy. The diesel emissions generally had rev/MJth values orders of magnitude higher than those of large utility-scale combustors (natural gas, coal, oil, or wood) but orders of magnitude lower than those of inefficient open burning (e.g., residential wood fireplaces). These comparative data of the potential health effects of a variety of biodiesel fuels will help inform the life-cycle assessment and use of biodiesel fuels.

Instillation of coarse ash particulate matter and lipopolysaccharide produces a systemic inflammatory response in mice.

Coronary ischemic events increase significantly following a "bad air" day. Ambient particulate matter (PM10) is the pollutant most strongly associated with these events. PM10 produces inflammatory injury to the lower airways. It is not clear, however, whether pulmonary inflammation translates to a systemic response. Lipopolysaccharide (LPS) is a proinflammatory molecule often associated with the coarse fraction of PM. It was hypothesized that PM>2.5 from coal plus LPS induce pulmonary inflammation leading to a systemic inflammatory response. Mice were intratracheally instilled with saline, PM (200 microg), PM + LPS10 (PM + 10 microg LPS), or PM + LPS100 (PM + 100 microg LPS). Eighteen hours later, histologic analysis was performed on lungs from each group. Pulmonary and systemic inflammation were assessed by measuring the proinflammatory cytokines tumor necrosis factor (TNF)-alpha and interleukin (IL)-6 in the pulmonary supernatant and plasma. In a follow-up study, the effects of LPS alone were assessed. Histologic analysis revealed a dose-dependent elevation in pulmonary inflammation with all treatments. Pulmonary TNF-alpha and IL-6 both increased significantly with PM + LPS100 treatment. Regarding plasma, TNF-alpha significantly increased in both PM + LPS10 and PM + LPS100 treatments. For plasma IL-6, all groups tended to rise with a significant increase in the PM + LPS100 group. The results of the follow-up study indicate that the responses to PM + LPS were not due to LPS alone. These results suggest that coarse coal fly ash PM>2.5 combined with LPS produced pulmonary and systemic inflammatory responses. The resulting low-level systemic inflammation may contribute to the increased severity of ischemic heart disease observed immediately following a bad air day.

Diesel exhaust enhanced susceptibility to influenza infection is associated with decreased surfactant protein expression.

We have previously shown that exposure of respiratory epithelial cells to diesel exhaust (DE) enhances susceptibility to influenza infection and increases the production of interleukin (IL)-6 and interferon (IFN)-beta. The purpose of this study was to confirm and expand upon these in vitro results by assessing the effects of DE exposure on the progression of influenza infection and on development of associated pulmonary immune and inflammatory responses in vivo. BALB/c mice were exposed to air or to DE containing particulate matter at concentrations of 0.5 or 2 mg/m(3) for 4 h/day for 5 days and subsequently instilled with influenza A/Bangkok/1/79 virus. Exposure to 0.5 mg/m(3) (but not the higher 2-mg/m(3) dose) of DE increased susceptibility to influenza infection as demonstrated by a significant increase in hemagglutinin (HA) mRNA levels, a marker of influenza copies, and greater immunohistochemical staining for influenza virus protein in the lung. The enhanced susceptibility to infection observed in mice exposed to 0.5 mg/m(3) of DE was associated with a significant increase in the expression of IL-6, while antiviral lung IFN levels were unaffected. Analysis of the expression and production of surfactant proteins A and D, which are components of the interferon-independent antiviral defenses, showed that these factors were decreased following exposure to 0.5 mg/m(3) of DE but not to the higher 2-mg/m(3) concentration. Taken together, the results demonstrate that exposure to DE enhances the susceptibility to respiratory viral infections by reducing the expression and production of antimicrobial surfactant proteins.