RESUMEN
Lithium-ion battery electrodes are typically manufactured via slurry casting, which involves mixing active material particles, conductive carbon, and a polymeric binder in a solvent, followed by casting and drying the coating on current collectors (Al or Cu). These electrodes are functional but still limited in terms of pore network percolation, electronic connectivity, and mechanical stability, leading to poor electron/ion conductivities and mechanical integrity upon cycling, which result in battery degradation. To address this, we fabricate trichome-like carbon-iron fabrics via a combination of electrospinning and pyrolysis. Compared with slurry cast Fe2O3 and graphite-based electrodes, the carbon-iron fabric (CMF) electrode provides enhanced high-rate capacity (10C and above) and stability, for both half cell and full cell testing (the latter with a standard lithium nickel manganese oxide (LNMO) cathode). Further, the CMFs are free-standing and lightweight; therefore, future investigation may include scaling this as an anode material for pouch cells and 18,650 cylindrical batteries.
RESUMEN
The electrochemical behaviour of ferrocene (Fc) is investigated in six different deep eutectic solvents (DESs) formed by means of hydrogen bonding between selected ammonium and phosphonium salts with glycerol and ethylene glycol. Combinations of cyclic voltammetry and chronoamperometry are employed to characterise the DESs. The reductive and oxidative potential limits are reported versus the Fc/Fc(+) couple. The diffusion coefficient, D, of ferrocene in all studied DESs is found to lie between 8.49 × 10(-10) and 4.22 × 10(-8) cm(2) s(-1) (these do not change significantly with concentration). The standard rate constant for heterogeneous electron transfer across the electrode/DES interface is determined to be between 1.68 × 10(-4) and 5.44 × 10(-4) cm s(-1) using cyclic voltammetry. These results are of the same order of magnitude as those reported for other ionic liquids in the literature.
RESUMEN
The hierarchically nanostructured NiTe@CoxSy composites are constructed on a foamed nickel substrate by a two-step electrode preparation process. Structural characterization shows the dense growing of CoxSy nanosheets around NiTe nanorods forms a hierarchical nanostructure which possesses synergetic effects from both compositional and structural complementarity, more pathways for ion/electrolyte transport, richer redox active sites, and better conductivity. Thanks to the rational design of this hierarchical structure, NiTe@CoxSy delivers a high areal capacitance of 7.7F cm-2 at 3 mA cm-2 and achieves the improved capacitance retention of 97.9% after 10,000 cycles. Of particular importance is the successful fabrication of NiTe@CoxSy//activated carbon hybrid supercapacitors. This hybrid device has a wide operating voltage window, high areal energy density of 0.48 mWh cm-2 at 2.55 mW cm-2, impressive rate capability of 62.3% even after a 20-fold increase of the current density, and a 115.1% of initial capacitance retention after 15,000 cycles. Meanwhile, two tandem such hybrid devices can easily drive a pair of mini fans or light up a heart-like pattern assembled by 10 red LEDs. These experimental results not only demonstrate that the hierarchically nanostructured NiTe@CoxSy composites can serve as a prospective candidate electrode; but also develop a novel strategy about how to achieve high-performance stockpile equipment by rationale designing a desirable nanostructures.
RESUMEN
Hybrid redox flow cells (HRFC) are key enablers for the development of reliable large-scale energy storage systems; however, their high cost, limited cycle performance, and incompatibilities associated with the commonly used carbon-based electrodes undermine HRFC's commercial viability. While this is often linked to lack of suitable electrocatalytic materials capable of coping with HRFC electrode processes, the combinatory use of nanocarbon additives and carbon paper electrodes holds new promise. Here, by coupling electrophoretically deposited nitrogen-doped graphene (N-G) with carbon electrodes, their surprisingly beneficial effects on three types of HRFCs, namely, hydrogen/vanadium (RHVFC), hydrogen/manganese (RHMnFC), and polysulfide/air (S-Air), are revealed. RHVFCs offer efficiencies over 70% at a current density of 150 mA cm-2 and an energy density of 45 Wh L-1 at 50 mA cm-2, while RHMnFCs achieve a 30% increase in energy efficiency (at 100 mA cm-2). The S-Air cell records an exchange current density of 4.4 × 10-2 mA cm-2, a 3-fold improvement of kinetics compared to the bare carbon paper electrode. We also present cost of storage at system level compared to the standard all-vanadium redox flow batteries. These figures-of-merit can incentivize the design, optimization, and adoption of high-performance HRFCs for successful grid-scale or renewable energy storage market penetration.