Flow-through Gas Phase Photocatalysis Using TiO2 Nanotubes on Wirelessly Anodized 3D-Printed TiNb Meshes.

In this work, for the first time 3D Ti-Nb meshes of different composition, i.e., Ti, Ti-1Nb, Ti-5Nb, and Ti-10 Nb, were produced by direct ink writing. This additive manufacturing method allows tuning of the mesh composition by simple blending of pure Ti and Nb powders. The 3D meshes are extremely robust with a high compressive strength, giving potential use in photocatalytic flow-through systems. After successful wireless anodization of the 3D meshes toward Nb-doped TiO2 nanotube (TNT) layers using bipolar electrochemistry, they were employed for the first time for photocatalytic degradation of acetaldehyde in a flow-through reactor built based on ISO standards. Nb-doped TNT layers with low concentrations of Nb show superior photocatalytic performance compared with nondoped TNT layers due to the lower amount of recombination surface centers. High concentrations of Nb lead to an increased number of recombination centers within the TNT layers and reduce the photocatalytic degradation rates.

Enhanced CO Functionality on Carbon Papers Ensures Lowering Nucleation Delay of ALD for Ru towards Unprecedented Alkaline HER Activity.

The success in lowering the nucleation delay for Atomic Layer Deposition (ALD) of Ru on carbon surfaces is mitigated by constructive pretreatments resulting enhancement of CO functionality. Treatment of the carbon papers (CP) allowed Ru species deposition for minimum number of ALD cycles (25 cycles) with good conformality. The development of electrocatalysts from single atoms to nanoparticles (NPs) on conductive supports with low metal loadings, thus improving performance, is essential in electrocatalysis. For alkaline hydrogen evolution reaction, ALD decorated CPs with Ru exhibit low onset potentials of ≈4.7 mV versus reversable hydrogen electrode (RHE) (at 10 mA cm-2 ) and a high turnover frequency of 1.92 H2 s-1 at 30 mV versus RHE. The Ru decorated CPs show comparable to higher catalytic activity than of Platinum (Pt) decorated CP also developed by ALD. The current representation of unfamiliar catalytic activities of Ru active centers developed by ALD, pave a bright and sustainable path for energy conversion reactions.

Photocatalytic degradation of gaseous pollutants on nanostructured TiO2 films of various thickness and surface area.

This work deals with the preparation of TiO2 nanoparticulate layers of various mass (0.05 mg/cm2 to 2 mg/cm2) from three commercial nanopowder materials, P90, P25 and CG 300, their characterisation (profilometry, BET and SEM) and evaluation of their photocatalytic activity in the gaseous phase in a flow-through photoreactor according to the ISO standard (ISO 22197-2). Hexane was chosen as a single model pollutant and a mixture of four compounds, namely acetaldehyde, acetone, heptane and toluene was used for the evaluation of the efficiency of simultaneous removal of several pollutants. A linear dependence between the layer mass and the layer thickness for all materials was found. Up to a layer mass 0.5 mg/cm2, the immobilisation P90 and P25 powder did not result in a decrease in BET surface area, whereas with an increase in layer mass to 1 mg/cm2, a decrease of the BET surface was observed, being more significant in the case of P90. The photocatalytic conversion of hexane was comparable for all immobilised powders up to a layer mass of 0.5 mg/cm2. For higher layer mass, the photocatalytic conversion of hexane on P25 and P90 differ; the latter achieved about 30% higher conversion. In the case of the simultaneous degradation of four compounds, acetaldehyde was degraded best, followed by acetone and toluene; the least degraded compound was heptane. The measurement of released CO2 revealed that 90% of degraded hexane was mineralised to CO2 and water while for a mixture of 4 VOCs, the level of mineralisation was 83%.

Enzyme-Photocatalyst Tandem Microrobot Powered by Urea for Escherichia coli Biofilm Eradication.

Urinary-based infections affect millions of people worldwide. Such bacterial infections are mainly caused by Escherichia coli (E. coli) biofilm formation in the bladder and/or urinary catheters. Herein, the authors present a hybrid enzyme/photocatalytic microrobot, based on urease-immobilized TiO2 /CdS nanotube bundles, that can swim in urea as a biocompatible fuel and respond to visible light. Upon illumination for 2 h, these microrobots are able to remove almost 90% of bacterial biofilm, due to the generation of reactive radicals, while bare TiO2 /CdS photocatalysts (non-motile) or urease-coated microrobots in the dark do not show any toxic effect. These results indicate a synergistic effect between the self-propulsion provided by the enzyme and the photocatalytic activity induced under light stimuli. This work provides a photo-biocatalytic approach for the design of efficient light-driven microrobots with promising applications in microbiology and biomedicine.

Anodic TiO2 Nanotubes on 3D-Printed Titanium Meshes for Photocatalytic Applications.

In this work, large 3D Ti meshes fabricated by direct ink writing were wirelessly anodized for the first time to prepare highly photocatalytically active TiO2 nanotube (TNT) layers. The use of bipolar electrochemistry enabled the fabrication of TNT layers within the 3D Ti meshes without the establishment of an electrical contact between Ti meshes and the potentiostat, confirming its unique ability and advantage for the synthesis of anodic structures on metallic substrates with a complex geometry. TNT layers with nanotube diameters of up to 110 nm and thicknesses of up to 3.3 µm were formed. The TNT-layer-modified 3D Ti meshes showed a superior performance for the photocatalytic degradation of methylene blue in comparison to TiO2-nanoparticle-decorated and nonanodized Ti meshes (with a thermal oxide layer), resulting in multiple increases in the dye degradation rate. The results presented here open new horizons for the employment of anodized 3D Ti meshes in various flow-through (photo)catalytic reactors.

SiO2 Fibers of Two Lengths and Their Effect on Cellular Responses of Macrophage-like Cells.

The immunoreactivity or/and stress response can be induced by nanomaterials' different properties, such as size, shape, etc. These effects are, however, not yet fully understood. This study aimed to clarify the effects of SiO2 nanofibers (SiO2NFs) on the cellular responses of THP-1-derived macrophage-like cells. The effects of SiO2NFs with different lengths on reactive oxygen species (ROS) and pro-inflammatory cytokines TNF-α and IL-1ß in THP-1 cells were evaluated. From the two tested lengths, it was only the L-SiO2NFs with a length ≈ 44 ± 22 µm that could induce ROS. Compared to this, only S-SiO2NFs with a length ≈ 14 ± 17 µm could enhance TNF-α and IL-1ß expression. Our results suggested that L-SiO2NFs disassembled by THP-1 cells produced ROS and that the inflammatory reaction was induced by the uptake of S-SiO2NFs by THP-1 cells. The F-actin staining results indicated that SiO2NFs induced cell motility and phagocytosis. There was no difference in cytotoxicity between L- and S-SiO2NFs. However, our results suggested that the lengths of SiO2NFs induced different cellular responses.

Chiral Templating of Polycarbonate Membranes by Pinene Using the Modified Atomic Layer Deposition Approach.

In this article, chiral templating of a polycarbonate (PC) membrane by (-)-α-pinene using the atomic layer deposition (ALD) approach is investigated. The templating with the enantiomer of (-)-α-pinene, used as a case compound, was performed either on the original commercial PC membrane or on the PC membrane with a beforehand deposited Al2O3 layer. The efficiency of the templating was assessed by a difference in the membrane ability to adsorb/absorb (-)-α-pinene, (+)-α-pinene, and their racemic mixture, using a very sensitive gas sorption analyzer. The results clearly show that the solution-diffusion mechanism rather than the sieving mechanism applied for adsorption/absorption of (-/+)-α-pinene enantiomers, which have the same size of the molecule. The PC membrane with the predeposited Al2O3 before the (-)-α-pinene templating shows significantly higher sorption of (-)-α-pinene compared to (+)-α-pinene and racemate, which clearly demonstrates the presence of a chiral recognition effect.

Generation and Stabilization of Small Platinum Clusters Pt12±x Inside a Metal-Organic Framework.

The generation and matrix stabilization of ligand-free, small platinum nanoclusters (NCs) Pt12±x is presented. The metal-organic framework-template approach is based on encapsulating CO-ligated, atom-precise Pt9 Chini clusters [{Pt3(CO)6}3]2- into the zeolitic imidazolate framework ZIF-8. The selective formation of the air-stable inclusion compound [NBu4]2[{Pt3(CO)6}4]@ZIF-8 of defined atomicity Pt12 and with Pt loadings of 1-20 wt % was monitored by UV/vis and IR spectroscopy and was confirmed by high-resolution transmission electron microscopy (HR-TEM), high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), X-ray photoelectron spectroscopy (XPS), and powder X-ray diffraction (PXRD). Thermally induced decarbonylation at 200 °C yields the composite material Ptn@ZIF-8 with a cluster atomicity n close to 12, irrespective of the Pt loading. The PtNCs retain their size even during annealing at 300 °C for 24 h and during catalytic hydrogenation of 1-hexene at 25 °C in the liquid phase. The Ptn@ZIF-8 material can conveniently be used for storing small PtNCs and their further processing. Removal of the protective ZIF-8 matrix under acidic conditions and transfer of the PtNCs to carbon substrates yields defined aggregation to small Pt nanoparticles (1.14 ± 0.35 nm, HR-TEM), which have previously shown exceptional performance in the electrocatalytic oxygen reduction reaction (ORR).

Optimizing the Size of Platinum Nanoparticles for Enhanced Mass Activity in the Electrochemical Oxygen Reduction Reaction.

High oxygen reduction (ORR) activity has been for many years considered as the key to many energy applications. Herein, by combining theory and experiment we prepare Pt nanoparticles with optimal size for the efficient ORR in proton-exchange-membrane fuel cells. Optimal nanoparticle sizes are predicted near 1, 2, and 3 nm by computational screening. To corroborate our computational results, we have addressed the challenge of approximately 1 nm sized Pt nanoparticle synthesis with a metal-organic framework (MOF) template approach. The electrocatalyst was characterized by HR-TEM, XPS, and its ORR activity was measured using a rotating disk electrode setup. The observed mass activities (0.87±0.14 A mgPt -1 ) are close to the computational prediction (0.99 A mgPt -1 ). We report the highest to date mass activity among pure Pt catalysts for the ORR within similar size range. The specific and mass activities are twice as high as the Tanaka commercial Pt/C catalysis.

Advanced immunocapture of milk-borne Salmonella by microfluidic magnetically stabilized fluidized bed.

The success of microfluidic immunocapture based on magnetic beads depends primarily on a sophisticated microscale separation system and on the quality of the magnetic immunosorbent. A microfluidic chip containing a magnetically stabilized fluidized bed (µMSFB), developed for the capture and on-chip amplification of bacteria, was recently described by Pereiro et al.. The present work shows the thorough development of anti-Salmonella magnetic immunosorbents with the optimal capture efficiency and selectivity. Based on the corresponding ISO standards, these parameters have to be high enough to capture even a few cells of bacteria in a proper aliquot of sample, e.g. milk. The selection of specific anti-Salmonella IgG molecules and the conditions for covalent bonding were the key steps in preparing an immunosorbent of the desired quality. The protocol for immunocapturing was first thoroughly optimized and studied in a batchwise arrangement, and then the carrier was integrated into the µMSFB chip. The combination of the unique design of the chip (guaranteeing the collision of cells with magnetic beads) with the advanced immunosorbent led to a Salmonella cell capture efficiency of up to 99%. These high values were achieved repeatedly even in samples of milk differing in fat content. The rate of nonspecific capture of Escherichia coli (i.e. the negative control) was only 2%.

Synthesis, Structure and Application of Intramolecularly-Coordinated Gallium Chalcogenides: Suitable Single-Source precursors for Gax Sey Materials.

Studies have been focused on the synthesis of N→Ga-coordinated organogallium selenides and tellurides [L1 Ga(µ-Se)]2 (1), [L2 Ga(µ-Se)]2 (2) and [L1 Ga(µ-Te)]2 (3), respectively, containing either N,C,N- or C,N-chelating ligands L1, 2 (L1 is {2,6-(Me2 NCH2 )2 C6 H3 }- and L2 is {2-(Et2 NCH2 )-4,6-tBu2 -C6 H2 }- ) having Ga/E (E=Se or Te) atoms in 1/1 ratio. To change the Ga/E ratio, an unusual N→Ga-coordinated organogallium tetraselenide L1 Ga(κ2 -Se4 ) (4) was prepared. An unprecedented complex (L1 Ga)2 (µ-Te2 )(µ-Te) (5), as the result of the non-stability of 3, was also isolated. Compound 2 is a suitable single-source precursor for the preparation of amorphous GaSe thin films by the spin coating. Moreover, simple heating of an octadecylamine solution of 2 provided, after work up, monoclinic Ga2 Se3 crystals with different crystallinity according to conditions used. Therefore, compound 2 may be also used as a source of Ga2 Se3 in the low-temperature doping process of Bi2 Se3 .

Atomic Layer Deposition Al2O3 Coatings Significantly Improve Thermal, Chemical, and Mechanical Stability of Anodic TiO2 Nanotube Layers.

We report on a very significant enhancement of the thermal, chemical, and mechanical stability of self-organized TiO2 nanotubes layers, provided by thin Al2O3 coatings of different thicknesses prepared by atomic layer deposition (ALD). TiO2 nanotube layers coated with Al2O3 coatings exhibit significantly improved thermal stability as illustrated by the preservation of the nanotubular structure upon annealing treatment at high temperatures (870 °C). In addition, a high anatase content is preserved in the nanotube layers against expectation of the total rutile conversion at such a high temperature. Hardness of the resulting nanotube layers is investigated by nanoindentation measurements and shows strongly improved values compared to uncoated counterparts. Finally, it is demonstrated that Al2O3 coatings guarantee unprecedented chemical stability of TiO2 nanotube layers in harsh environments of concentrated H3PO4 solutions.

Atomic Layer Deposition for Coating of High Aspect Ratio TiO2 Nanotube Layers.

We present an optimized approach for the deposition of Al2O3 (as a model secondary material) coating into high aspect ratio (≈180) anodic TiO2 nanotube layers using the atomic layer deposition (ALD) process. In order to study the influence of the diffusion of the Al2O3 precursors on the resulting coating thickness, ALD processes with different exposure times (i.e., 0.5, 2, 5, and 10 s) of the trimethylaluminum (TMA) precursor were performed. Uniform coating of the nanotube interiors was achieved with longer exposure times (5 and 10 s), as verified by detailed scanning electron microscopy analysis. Quartz crystal microbalance measurements were used to monitor the deposition process and its particular features due to the tube diameter gradient. Finally, theoretical calculations were performed to calculate the minimum precursor exposure time to attain uniform coating. Theoretical values on the diffusion regime matched with the experimental results and helped to obtain valuable information for further optimization of ALD coating processes. The presented approach provides a straightforward solution toward the development of many novel devices, based on a high surface area interface between TiO2 nanotubes and a secondary material (such as Al2O3).

Ultrathin TiO2 Coatings via Atomic Layer Deposition Strongly Improve Cellular Interactions on Planar and Nanotubular Biomedical Ti Substrates.

This work aims to investigate the chemical and/or structural modification of Ti and Ti-6Al-4V (TiAlV) alloy surfaces to possess even more favorable properties toward cell growth. These modifications were achieved by (i) growing TiO2 nanotube layers on these substrates by anodization, (ii) surface coating by ultrathin TiO2 atomic layer deposition (ALD), or (iii) by the combination of both. In particular, an ultrathin TiO2 coating, achieved by 1 cycle of TiO2 ALD, was intended to shade the impurities of F- and V-based species in tested materials while preserving the original structure and morphology. The cell growth on TiO2-coated and uncoated TiO2 nanotube layers, Ti foils, and TiAlV alloy foils were compared after incubation for up to 72 h. For evaluation of the biocompatibility of tested materials, cell lines of different tissue origin, including predominantly MG-63 osteoblastic cells, were used. For all tested nanomaterials, adding an ultrathin TiO2 coating improved the growth of MG-63 cells and other cell lines compared with the non-TiO2-coated counterparts. Here, the presented approach of ultrathin TiO2 coating could be used potentially for improving implants, especially in terms of shading problematic F- and V-based species in TiO2 nanotube layers.

2D FeSx Nanosheets by Atomic Layer Deposition: Electrocatalytic Properties for the Hydrogen Evolution Reaction.

2-dimensional FeSx nanosheets of different sizes are synthesized by applying different numbers of atomic layer deposition (ALD) cycles on TiO2 nanotube layers and graphite sheets as supporting materials and used as an electrocatalyst for the hydrogen evolution reaction (HER). The electrochemical results confirm electrocatalytic activity in alkaline media with outstanding long-term stability (>65 h) and enhanced catalytic activity, reflected by a notable drop in the initial HER overpotential value (up to 26 %). By using a range of characterization techniques, the origin of the enhanced catalytic activity was found to be caused by the synergistic interplay between in situ morphological and compositional changes in the 2D FeSx nanosheets during HER. Under the application of a cathodic potential in alkaline media, the as-synthesized 2D FeSx nanosheets transformed into iron oxyhydroxide-iron oxysulfide core-shell nanoparticles, which exhibited a higher active catalytic surface and newly created Fe-based HER catalytic sites.

Gigahertz-Based Visible Light Detection Enabled via CdS-Coated TiO2 Nanotube Layers.

Detection of visible light is a key component in material characterization techniques and often a key component of quality or purity control analyses for health and safety applications. Here in this work, to enable visible light detection at gigahertz frequencies, a planar microwave resonator is integrated with high aspect ratio TiO2 nanotube (TNT) layer-sensitized CdS coating using the atomic layer deposition (ALD) technique. This unique method of visible light detection with microwave-based sensing improves integration of the light detection devices with digital technology. The designed planar microwave resonator sensor was implemented and tested with resonant frequency between 8.2 and 8.4 GHz and a resonant amplitude between -15 and -25 dB, depending on the wavelength of the illuminated light illumination on the nanotubes. The ALD CdS coating sensitized the nanotubes in visible light up to ∼650 nm wavelengths, as characterized by visible spectroscopy. Furthermore, CdS-coated TNT layer integration with the planar resonator sensor allowed for development of a robust microwave sensing platform with improved sensitivity to green and red light (60 and 1300%, respectively) compared to the blank TNT layers. Moreover, the CdS coating of the TNT layer enhanced the sensor's response to light exposure and resulted in shorter recovery times once the light source was removed. Despite having a CdS coating, the sensor was capable of detecting blue and UV light; however, refining the sensitizing layer could potentially enhance its sensitivity to specific wavelengths of light in certain applications.

Transcriptomic hallmarks of in vitro TiO2 nanotubes toxicity in Chlamydomonas reinhardtii.

Recently, more accessible transcriptomic approaches have provided a new and deeper understanding of environmental toxicity. The present study focuses on the transcriptomic profiles of green microalgae Chlamydomonas reinhardtii exposed to new industrially promising material, TiO2 nanotubes (NTs), as an example of a widely used one-dimensional nanomaterial. The first algal in vitro assay included 2.5 and 7.5 mg/L TiO2 NTs, resulting in a dose-dependent negative effect on biological endpoints. At a working concentration of 7.5 mg/L, RNA-sequencing showed a mainly negative effect on the cells. In summary, the results indicated metabolic disruption, such as ATP loss, damage to mitochondria and chloroplasts, loss of solutes due to permeated membranes, and cell wall damage. Moreover, apoptosis-induced transcripts were detected. Interestingly, reactivation of transposons was observed. In signalling and transcription pathways, including chromatin remodelling and locking, the annotated genes were downregulated.

Fast-Charging Capability of Thin-Film Prussian Blue Analogue Electrodes for Aqueous Sodium-Ion Batteries.

Prussian blue analogues are considered as promising candidates for aqueous sodium-ion batteries providing a decently high energy density for stationary energy storage. However, suppose the operation of such materials under high-power conditions could be facilitated. In that case, their application might involve fast-response power grid stabilization and enable short-distance urban mobility due to fast re-charging. In this work, sodium nickel hexacyanoferrate thin-film electrodes are synthesized via a facile electrochemical deposition approach to form a model system for a robust investigation. Their fast-charging capability is systematically elaborated with regard to the electroactive material thickness in comparison to a ″traditional″ composite-type electrode. It is found that quasi-equilibrium kinetics allow extremely fast (dis)charging within a few seconds for sub-micron film thicknesses. Specifically, for a thickness below ≈ 500 nm, 90% of the capacity can be retained at a rate of 60C (1 min for full (dis)charge). A transition toward mass transport control is observed when further increasing the rate, with thicker films being dominated by this mode earlier than thinner films. This can be entirely attributed to the limiting effects of solid-state diffusion of Na+ within the electrode material. By presenting a PBA model cell yielding 25 Wh kg-1 at up to 10 kW kg-1, this work highlights a possible pathway toward the guided design of hybrid battery-supercapacitor systems. Furthermore, open challenges associated with thin-film electrodes are discussed, such as the role of parasitic side reactions, as well as increasing the mass loading.

High-Frequency TiO2 Nanotube-Adapted Microwave Coplanar Waveguide Resonator for High-Sensitivity Ultraviolet Detection.

Ultraviolet (UV) sensors are a key component in growing applications such as water quality treatment and environmental monitoring, with considerable interest in their miniaturization and enhanced operation. This work presents a passive gold coplanar waveguide split ring resonator integrated with anodic self-organized TiO2 nanotube (TNT) membranes with a thickness of 20 µm to provide real-time UV detection. The resonator operated as a one-port device to capture the reflection coefficient (S11) signal, with a center frequency of 16 GHz and a notch amplitude of -88 dB. It was experimentally analyzed for its UV sensing capability in the range of 36.5-463 µW/cm2. The high-frequency resonator was improved through design choices including the addition of a tapered input transmission line, wire bonding for practical device design, and an interdigitated capacitive ring gap. The high frequency also helped mitigate noise due to water vapor or environmental contaminants. S11 amplitude variation was found through both experiments and modeling to follow a linear trend with UV illumination intensity. The resonator exhibited over 45 ± 2 dB shift in the resonant amplitude under the highest UV illumination conditions, with a sensitivity of 0.084 dB/µW cm-2 and the potential to sense UV intensity as low as 2.7 µW/cm2. The presented device enabled a repeatable and accurate microwave response under UV illumination with very high sensitivity, entirely through the use of passive circuit elements.

The centrifugal spinning of vitamin doped natural gum fibers for skin regeneration.

The study investigates the use of fiber carriers, based on biopolymeric gums as potential candidates for cosmetic and dermatological applications, in particular for skin regeneration. Gum arabic (GA), xanthan gum (XA), and gum karaya (GK) were used as the main gum materials for the fibers, which were prepared by centrifugal spinning from an aqueous solution. These solutions of different mass gum ratios were blended with poly (ethylene oxide) (PEO) for better spinnability. Finally, vitamins E and C were added to selected solutions of gums. The resulting fibers were extensively investigated. The morphology and structure of all fibers were investigated by scanning electron microscopy and Fourier transformed infrared spectroscopy. Most importantly, they were characterized by the release of vitamin E loaded in the fibers using UV-VIS spectroscopy. The presentation will show that the newly prepared fibers from GA and PEO represent a very promising material for cosmetic and dermatologic applications.