Evaluation of the Effect of Bariatric Surgery-Induced Weight Loss on Knee Gait and Cartilage Degeneration.

The objective of the study was to investigate the effects of bariatric surgery-induced weight loss on knee gait and cartilage degeneration in osteoarthritis (OA) by combining magnetic resonance imaging (MRI), gait analysis, finite element (FE) modeling, and cartilage degeneration algorithm. Gait analyses were performed for obese subjects before and one-year after the bariatric surgery. FE models were created before and after weight loss for those subjects who did not have severe tibio-femoral knee cartilage loss. Knee cartilage degenerations were predicted using an adaptive cartilage degeneration algorithm which is based on cumulative overloading of cartilage, leading to iteratively altered cartilage properties during OA. The average weight loss was 25.7±11.0 kg corresponding to a 9.2±3.9 kg/m2 decrease in body mass index (BMI). External knee rotation moment increased, and minimum knee flexion angle decreased significantly (p < 0.05) after weight loss. Moreover, weight loss decreased maximum cartilage degeneration by 5±23% and 13±11% on the medial and lateral tibial cartilage surfaces, respectively. Average degenerated volumes in the medial and lateral tibial cartilage decreased by 3±31% and 7±32%, respectively, after weight loss. However, increased degeneration levels could also be observed due to altered knee kinetics. The present results suggest that moderate weight loss changes knee kinetics and kinematics and can slow-down cartilage degeneration for certain patients. Simulation results also suggest that prediction of cartilage degeneration is subject-specific and highly depend on the altered gait loading, not just the patient's weight.

Histomorphometric and osteocytic characteristics of cortical bone in male subtrochanteric femoral shaft.

The histomorphometric properties of the subtrochanteric femoral region have rarely been investigated. The aim of this study was to investigate the age-associated variations and regional differences of histomorphometric and osteocytic properties in the cortical bone of the subtrochanteric femoral shaft, and the association between osteocytic and histological cortical bone parameters. Undecalcified histological sections of the subtrochanteric femoral shaft were obtained from cadavers (n = 20, aged 18-82 years, males). They were cut and stained using modified Masson-Goldner stain. Histomorphometric parameters of cortical bone were analysed with ×50 and ×100 magnification after identifying cortical bone boundaries using our previously validated method. Within cortical bone areas, only complete osteons with typical concentric lamellae and cement line were selected and measured. Osteocytic parameters of cortical bone were analyzed under phase contrast microscopy and epifluorescence within microscopic fields (0.55 mm2 for each). The cortical widths of the medial and lateral quadrants were significantly higher than other quadrants (P < 0.01). Osteonal area per cortical bone area was lower and cortical porosities were higher in the posterior quadrant than in the other quadrants (P < 0.05). Osteocyte lacunar number per cortical bone area was found higher in the young subjects (≤ 50 years) than in the older ones (> 50 years) both before and after adjustments for body height and weight (P < 0.05). Moreover, significant but low correlations were found between the cortical bone and osteocytic parameters (0.20 ≤ R2  ≤ 0.35, P < 0.05). It can be concluded that in healthy males, the cortical histomorphometric parameters differ between the anatomical regions of the subtrochanteric femoral shaft, and are correlated with the osteocytic parameters from the same site. These findings may be of use when discussing mechanisms that predispose patients to decreasing bone strength.

Porosity predicted from ultrasound backscatter using multivariate analysis can improve accuracy of cortical bone thickness assessment.

A rapidly growing area of interest in quantitative ultrasound assessment of bone is to determine cortical bone porosity from ultrasound backscatter. Current backscatter analyses are based on numerical simulations, while there are no published reports of successful experimental measurements. In this study, multivariate analysis is applied to ultrasound reflections and backscatter to predict cortical bone porosity. The porosity is then applied to estimate cortical bone radial speed of sound (SOS) and thickness using ultrasound backscatter signals obtained at 2.25 and 5 MHz center frequencies from cortical bone samples (n = 43) extracted from femoral diaphyses. The study shows that the partial least squares regression technique could be employed to successfully predict (R2 = 0.71-0.73) cortical porosity. It is found that this multivariate approach can reduce uncertainty in pulse-echo assessment of cortical bone thickness from 0.220 to 0.045 mm when porosity based radial SOS was applied, instead of a constant value from literature. Upon further validation, accurate estimation of cortical bone porosity and thickness may be applied as a financially viable option for fracture risk assessment of individuals.

Finite difference time domain model of ultrasound propagation in agarose scaffold containing collagen or chondrocytes.

Measurement of ultrasound backscattering is a promising diagnostic technique for arthroscopic evaluation of articular cartilage. However, contribution of collagen and chondrocytes on ultrasound backscattering and speed of sound in cartilage is not fully understood and is experimentally difficult to study. Agarose hydrogels have been used in tissue engineering applications of cartilage. Therefore, the aim of this study was to simulate the propagation of high frequency ultrasound (40 MHz) in agarose scaffolds with varying concentrations of chondrocytes (1 to 32 × 10(6) cells/ml) and collagen (1.56-200 mg/ml) using transversely isotropic two-dimensional finite difference time domain method (FDTD). Backscatter and speed of sound were evaluated from the simulated pulse-echo and through transmission measurements, respectively. Ultrasound backscatter increased with increasing collagen and chondrocyte concentrations. Furthermore, speed of sound increased with increasing collagen concentration. However, this was not observed with increasing chondrocyte concentrations. The present study suggests that the FDTD method may have some applicability in simulations of ultrasound scattering and propagation in constructs containing collagen and chondrocytes. Findings of this study indicate the significant role of collagen and chondrocytes as ultrasound scatterers and can aid in development of modeling approaches for understanding how cartilage architecture affects to the propagation of high frequency ultrasound.

Differences in acoustic impedance of fresh and embedded human trabecular bone samples-Scanning acoustic microscopy and numerical evaluation.

Trabecular bone samples are traditionally embedded and polished for scanning acoustic microscopy (SAM). The effect of sample processing, including dehydration, on the acoustic impedance of bone is unknown. In this study, acoustic impedance of human trabecular bone samples (n = 8) was experimentally assessed before (fresh) and after embedding using SAM and two-dimensional (2-D) finite-difference time domain simulations. Fresh samples were polished with sandpapers of different grit (P1000, P2500, and P4000). Experimental results indicated that acoustic impedance of samples increased significantly after embedding [mean values 3.7 MRayl (fresh), 6.1 MRayl (embedded), p < 0.001]. After polishing with different papers, no significant changes in acoustic impedance were found, even though higher mean values were detected after polishing with finer (P2500 and P4000) papers. A linear correlation (r = 0.854, p < 0.05) was found between the acoustic impedance values of embedded and fresh bone samples polished using P2500 SiC paper. In numerical simulations dehydration increased the acoustic impedance of trabecular bone (38%), whereas changes in surface roughness of bone had a minor effect on the acoustic impedance (-1.56%/0.1 µm). Thereby, the numerical simulations corroborated the experimental findings. In conclusion, acoustic impedance measurement of fresh trabecular bone is possible and may provide realistic material values similar to those of living bone.

Inter-individual changes in cortical bone three-dimensional microstructure and elastic coefficient have opposite effects on radial sound speed.

Knowledge about simultaneous contributions of tissue microstructure and elastic properties on ultrasound speed in cortical bone is limited. In a previous study, porosities and elastic coefficients of cortical bone in human femurs were shown to change with age. In the present study, influences of inter-individual and site-dependent variation in cortical bone microstructure and elastic properties on radial speed of sound (SOS; at 4, 6, and 8 MHz) were investigated using three-dimensional (3D) finite difference time domain modeling. Models with fixed (nominal model) and sample-specific (sample-specific model) values of radial elastic coefficients were compared. Elastic coefficients and microstructure for samples (n = 24) of human femoral shafts (n = 6) were derived using scanning acoustic microscopy and micro-computed tomography images, respectively. Porosity-related SOS varied more extensively in nominal models than in sample-specific models. Linear correlation between pore separation and SOS was similar (R = 0.8, p < 0.01, for 4 MHz) for both models. The determination coefficient (R(2)= 0.75, p < 0.05) between porosity and radial SOS, especially at 4 MHz, was highest in the posterior quadrant. The determination coefficient was lower for models with sample-specific values of radial elastic coefficient implemented (R(2) < 0.33, p < 0.05), than for nominal models (0.48 < R(2)< 0.63, p < 0.05). This information could be useful in in vivo pulse-echo cortical thickness measurements applying constant SOS.

Infrared thermography reveals effect of working posture on skin temperature in office workers.

INTRODUCTION: Musculoskeletal symptoms related to using traditional computer workstations are common. Quantitative methods for measuring muscle stress and strain are needed to improve ergonomics of workstations. We hypothesize that infrared thermography (IRT) is suited for this purpose. METHODS: This hypothesis was evaluated by estimating muscle activity in upright and traditional working postures with IRT and surface electromyography (sEMG). IRT and sEMG measurements were conducted in 14 female participants with both working postures. First, measurements with the traditional posture were performed. Later, participants had 1 month to adjust to the upright working posture before repeating the measurements. IRT images were acquired before and after a full working day, with sEMG recordings being conducted throughout the measurement days. Participants evaluated their neck pain severity using neck disability index (NDI) questionnaires before the first and after the second measurement day. RESULTS: Spatial variation in upper back temperature was higher (p = 0.008) when working in traditional posture and the upright working posture reduced (p < 0.05) upper back muscle activity. The NDI was significantly lower (p = 0.003) after working in the upright posture. CONCLUSION: IRT was found suitable for evaluating muscle activity and upright working posture to reduce the NDI and muscle activity in the upper back.

Characterizing human subchondral bone properties using near-infrared (NIR) spectroscopy.

Degenerative joint conditions are often characterized by changes in articular cartilage and subchondral bone properties. These changes are often associated with subchondral plate thickness and trabecular bone morphology. Thus, evaluating subchondral bone integrity could provide essential insights for diagnosis of joint pathologies. This study investigates the potential of optical spectroscopy for characterizing human subchondral bone properties. Osteochondral samples (n = 50) were extracted from human cadaver knees (n = 13) at four anatomical locations and subjected to NIR spectroscopy. The samples were then imaged using micro-computed tomography to determine subchondral bone morphometric properties, including: plate thickness (Sb.Th), trabecular thickness (Tb.Th), volume fraction (BV/TV), and structure model index (SMI). The relationship between the subchondral bone properties and spectral data in the 1st (650-950 nm), 2nd (1100-1350 nm) and 3rd (1600-1870 nm) optical windows were investigated using partial least squares (PLS) regression multivariate technique. Significant correlations (p < 0.0001) and relatively low prediction errors were obtained between spectral data in the 1st optical window and Sb.Th (R2 = 92.3%, error = 7.1%), Tb.Th (R2 = 88.4%, error = 6.7%), BV/TV (R2 = 83%, error = 9.8%) and SMI (R2 = 79.7%, error = 10.8%). Thus, NIR spectroscopy in the 1st tissue optical window is capable of characterizing and estimating subchondral bone properties, and can potentially be adapted during arthroscopy.

Phased-array ultrasound technology enhances accuracy of dual frequency ultrasound measurements - towards improved ultrasound bone diagnostics.

Overlying soft tissues attenuate ultrasound backscattered from bone, complicating diagnostics of osteoporosis at the most important fracture sites. Dual-frequency ultrasound technique (DFUS) has been proposed to solve this problem through determination of thickness and composition of overlying soft tissue. This study applies DFUS technique for the first time with a phased-array transducer to investigate if the thickness of two interfering layers (oil and water) can be accurately determined in a variety of configurations. Results indicate that DFUS may be used with phased-array ultrasound systems, making them a suitable combination to consider in future development of clinical in vivo ultrasound methodologies.

Effects of non-optimal focusing on dual-frequency ultrasound measurements of bone.

In pulse-echo (PE) ultrasound measurements, the use of focused transducers is desirable for quantitative assessment of bone characteristics because of the attenuation in the overlying soft tissues. However, the variable thickness and composition of the soft tissue overlying bone affect the focal depth of the ultrasound beam and induce errors into the measurements. To compensate for the attenuation-related effects caused by the interfering soft tissue (i.e., fat and lean tissue), a dual-frequency ultrasound (DFUS) technique was recently introduced. The aim of this study was to investigate the effect of non-optimal focal depth of the ultrasound beam on the determination of the integrated reflection coefficient (IRC) of bone when overlaid by an interfering layer composed of oil and water. The feasibility of the DFUS-based correction of the IRC was evaluated through numerical simulations and experimental measurements. Even when the interfering layer-bone interface was out of focus, the total thickness of the interfering layer could be accurately determined with the technique. However, based on the simulations, the errors in the determination of the composition of the interfering layer increased (0.004 to 113.8%) with the increase in distance between the interfering layer-bone interface and the focus of the ultrasound beam. Attenuation compensation, based on the true composition of the interfering layer, resulted in an average relative error of 22.3% in the IRC values calculated from the simulations. Interestingly, the attenuation compensation with the interfering layer composition estimated using the DFUS technique resulted in a smaller average relative error of 14.9% in the IRC values. The simulations suggest that DFUS can reduce the errors induced by soft tissue in bone PE ultrasound measurements. The experimental measurements indicate that the accuracy of the IRC measurements is rather similar when using DFUS correction or correction based on the true composition of the interfering layer. However, the results suggest that accurate determination of soft tissue composition may be difficult without optimal focusing of the ultrasound beam on the soft tissue-bone interface.

Numerical analysis of uncertainties in dual frequency bone ultrasound technique.

Quantitative ultrasound (QUS) measurements are used in the diagnostics of osteoporosis. However, the variation in the thickness and composition of the overlying soft tissue causes significant errors to the bone QUS parameters and diminishes the reliability of the technique in vivo. Recently, the dual frequency ultrasound (DFUS) technique was introduced to minimize the errors related to soft tissue effects. In this study, the significance of soft tissue induced errors and their elimination with the DFUS technique were simulated using the finite difference time domain technique. Furthermore, we investigated the potential of the DFUS corrected integrated reflection coefficient (IRC) of bone to detect changes in the cortical bone density. The effects of alterations in the thickness of fat and lean tissue layers and the inclination between the soft-tissues and between the soft tissue-bone layers were simulated. When the angle of the soft tissue interface was zero, i.e., perpendicular to the incident ultrasound beam, the DFUS-calculated soft tissue composition correlated highly linearly with the true soft tissue composition. The inclination between the soft tissue-bone layers was found to be critical. Even a 2-degree inclination between the soft tissue and the bone surface induced an almost 18% relative error in the corrected IRC. Increasing the inclination between the soft tissue layers increased the error in the DFUS-calculated lean and fat tissue thickness. This error was especially significant at inclination angles greater than 20 degrees. The significant soft tissue induced errors in IRC values (>300 %) could be effectively minimized (<10%) by means of the DFUS correction. Importantly, after the DFUS correction, physiologically relevant variation in the cortical bone density could be detected (p<0.05).