RESUMEN
Controlling the organization of self-assembling building blocks over a large area is crucial for lithographic tools based on the bottom-up approach. However, the fabrication of liquid crystal (LC) defect patterns with a particular ordering still remains a challenge because of the limited close-packed morphologies of LC defects. Here, we introduce a multiple-stamping domain separation method for the control of the dimensions and organization of LC defect structures. Prepatterns with various grid shapes on planar polyimide (PI) surfaces were fabricated by pressing a line-shaped stamp into the PI surfaces in two different directions, and then these surfaces were used to prepare LC defect structures confined to these grid domains. The dimensions of the LC defect structures, namely, the equilibrium diameter and the center to center spacing, are controlled by varying the line spacing of the stamps and the film thickness. A variety of arrangements of LC defects, including square, rhombic, hexagonal, and other oblique lattices, can be obtained by simply varying the stamping angle (Ω) between the first and second stamping directions. Furthermore, we demonstrate that the resulting controllable LC defect arrays can be used as templates for generating various patterns of nanoparticle clusters by trapping quantum dots (QDs) within the cores of the LC defects.
RESUMEN
Developing large-area, single domain of organic soft-building blocks such as block copolymers, colloids, and supramolecular materials is one of the most important issues in the materials science and nanotechnology. Owing to their small sizes, complex molecular architectures, and high mobility, supramolecular materials are not well-suited for building large area, single domain structures. In the described study, a single domain of supramolecular columnar dendrimers was created over large area. The columnar structures in these domains have smaller (4.5 nm) diameters, higher area densities (ca. 36 Tera-dots/in(2)) and larger domains (>0.1 × 0.1 mm(2)) than those of all existing BCP and colloidal assemblies. By simply annealing dendrimer thin films between two flat solid surfaces, single domains of hexagonal columnar structures are created over large macroscopic areas. Observations made in this effort should serve as the foundation for the design of new routes for bottom-up lithography based on supramolecular building blocks.
RESUMEN
Because the properties of molybdenum disulfide (MoS2) are strongly influenced by the sizes and boundaries of its domains, the direct visualization of large-area MoS2 domains is one of the most important challenges in MoS2 research. In the current study, we developed a simple and rapid method to observe and determine the boundaries of MoS2 domains. The technique, which depends on observations of nematic liquid crystal textures on the MoS2 surface, does not damage the sample and is not limited by domain size. Thus, this approach should significantly aid not only efforts aimed at gaining an understanding of the relationships between grain boundaries and properties of MoS2 but also those focusing on how domain sizes are controlled during large-area synthesis.
RESUMEN
A low-voltage-tunable one-dimensional nanobeam laser is realized by employing lithographically defined lateral electrodes. An InGaAsP nanobeam with a sub-micrometer width is transfer-printed in the middle of two electrodes using a polydimethylsiloxane stamp. Spectral tuning is achieved by controlling the molecular alignment of the surrounding liquid crystals (LCs). From µm-scale-gap structures, a total wavelength shift that exceed 6 nm is observed at a low voltage of less than 10 V. A measured spectral tuning rate of 0.87 nm/V, which is the largest value ever reported to our knowledge among LC-tuned photonic crystal lasers, was also noted.
RESUMEN
A dye-doped polymer-dispersed liquid crystal (PDLC) is an attractive material for application in smart windows. Smart windows using a PDLC can be operated simply and have a high contrast ratio compared to those of other devices that employed photochromic or thermochromic material. However, in conventional dye-doped PDLC methods, dye contamination can cause problems and has a limited degree of commercialization of electric smart windows. Here, we report on an approach to resolve dye-related problems by encapsulating the dye in monodispersed capsules. By encapsulation, a fabricated dye-doped PDLC had a contrast ratio of >120 at 600 nm. This fabrication method of encapsulating the dye in a core-shell structured microcapsule in a dye-doped PDLC device provides a practical platform for dye-doped PDLC-based smart windows.