The Recyclability of Fire-Retarded Biobased Polyamide 11 (PA11) Composites Reinforced with Basalt Fibers (BFs): The Influence of Reprocessing on Structure, Properties, and Fire Behavior.

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FRs). Significant amounts of FRs are usually required to effectively affect a polymer's burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but also, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of the four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame-retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC), and pentaerythritol (PER) and its composites containing additional short basalt fibers (BFs). Composites manufactured via twin-screw extrusion were subjected to four reprocessing cycles using injection molding. A comprehensive analysis of their structural, mechanical, and fire behavior changes in each cycle was conducted. The obtained results confirmed the safety of using the proposed fire-retarded polyamide and its composites while reprocessing under the recommended process parameters without the risk of significant changes in the structure. The partial increase in flammability of reprocessed PA-based materials caused mainly by polymer degradation has been described.

Nanofibers and Microfibers for Osteochondral Tissue Engineering.

The use of fibers into scaffolds is a way to mimic natural tissues, in which fibrils are embedded in a matrix. The use of fibers can improve the mechanical properties of the scaffolds and may act as structural support for cell growth. Also, as the morphology of fibrous scaffolds is similar to the natural extracellular matrix, cells cultured on these scaffolds tend to maintain their phenotypic shape. Different materials and techniques can be used to produce micrfibers- and nanofibers for scaffolds manufacturing; cells, in general, adhere and proliferate very well on PCL, chitosan, silk fibroin, and other nanofibers. One of the most important techniques to produce microfibers/nanofibers is electrospinning. Nanofibrous scaffolds are receiving increasing attention in bone tissue engineering, because they are able to offer a favorable microenvironment for cell attachment and growth. Different polymers can be electrospun, i.e., polyester, polyurethane, PLA, PCL, collagen, and silk. Other materials such as bioglass fibers, nanocellulose, and even carbon fiber and fabrics have been used to help increase bioactivity, mechanical properties of the scaffold, and cell proliferation. A compilation of mechanical properties and most common biological tests performed on fibrous scaffolds is included in this chapter. HIGHLIGHTS: The use of microfibers and nanofibers allows for tailoring the scaffold properties. Electrospinning is one of the most important techniques nowadays to produce fibrous scaffolds. Microfibers and nanofibers use in scaffolds is a promising field to improve the behavior of scaffolds in osteochondral applications.

Thermal ecology and microhabitat use of an arboreal lizard in two different Pantanal wetland phytophysionomies (Brazil).

Temperature is one of the main environmental variables shaping the evolution and biology of terrestrial ectotherms. The Pantanal is the largest continuous wetland in the World. However, a lack of knowlegde still exists on the thermal ecology of terrestrial ectothems from this wetland. In this context, the thermal ecology of the lizard Tropidurus lagunablanca Carvalho, 2016 (Squamata, Tropiduridae) was investigated in the Brazilian Pantanal. The thermal ecology and microhabitat use of lizards from a riparian forest was compared to lizards from a park savanna. At both studied areas, air and body temperatures of lizards did not differ between sexes. Mean T. lagunablanca body temperatures were higher at the savanna compared to the forest, while air temperatures were similar in both habitats. The main substrates were tree trunks, with a frequency of approximately 90% of the observations. Lizards from the savanna used higher perches than those from the forest despite -in average- trees were higher at the forest. Lizard sun and shade exposure was similar for both areas. Lizards from both habitats showed similar strong linear relationships between body and air temperatures. However, lizard behaviour of using tree trunk perches differently under different sunlight situations suggests that these lizards actively thermoregulate. Further research on the thermoregulation abilities of this species, with a null hypotesis and behavioral observations will shed light on lizard thermal biology. Studies on the ecophysiological aspects of these lizards should be a priority to understand how they will react to climate change and which conservation measures will be more effective concerning their preservation.

Wind constraints on the thermoregulation of high mountain lizards.

Thermal biology of lizards affects their overall physiological performance. Thus, it is crucial to study how abiotic constraints influence thermoregulation. We studied the effect of wind speed on thermoregulation in an endangered mountain lizard (Iberolacerta aurelioi). We compared two populations of lizards: one living in a sheltered rocky area and the other living in a mountain ridge, exposed to strong winds. The preferred temperature range of I. aurelioi, which reflects thermal physiology, was similar in both areas, and it was typical of a cold specialist. Although the thermal physiology of lizards and the structure of the habitat were similar, the higher wind speed in the exposed population was correlated with a significant decrease in the effectiveness thermoregulation, dropping from 0.83 to 0.74. Our results suggest that wind reduces body temperatures in two ways: via direct convective cooling of the animal and via convective cooling of the substrate, which causes conductive cooling of the animal. The detrimental effect of wind on thermoregulatory effectiveness is surprising, since lizards are expected to thermoregulate more effectively in more challenging habitats. However, wind speed would affect the costs and benefits of thermoregulation in more complex ways than just the cooling of animals and their habitats. For example, it may reduce the daily activity, increase desiccation, or complicate the hunting of prey. Finally, our results imply that wind should also be considered when developing conservation strategies for threatened ectotherms.

Adaptive seasonal shifts in the thermal preferences of the lizard Iberolacerta galani (Squamata, Lacertidae).

The León rock lizard, Iberolacerta galani, lives in isolated mountains of Spain. We studied the seasonal changes in the thermal biology of I. galani between spring and summer. We calculated precision, accuracy and effectiveness of thermoregulation and the habitat thermal quality for spring, and compared with the values of summer. In addition, we studied how the shift in the thermal preferences of lizards would contribute to achieve a higher effectiveness of thermoregulation. Thermal preferences of León rock lizards are among the lowest in lacertids, and are also very narrow, maintaining the narrowness among seasons. As for summer (27.90-29.70°C, mean value =28.76°C), the thermal preferences of I. galani are also low in spring (29.60-31.10°C, mean value =30.38°C), supporting the idea that this species is adapted to cold environments. The habitat thermal quality is lower in spring (10.99°C) than in summer (9.36°C), while the effectiveness of thermoregulation is higher in spring (0.92) than in summer (0.80). We found that the seasonal shift in thermal preferences contributes significantly to enhance the effectiveness of thermoregulation in both seasons, more in spring (0.45°C) than in summer (0.16°C). Because I. galani inhabits isolated mountains, where the activity period is reduced from April to October, we hypothesize that the observed adaptation of the thermal preferences, which enhance thermoregulation to a larger extent in spring, may evolved to maximize performance during the reproductive season.

The peak of thermoregulation effectiveness: Thermal biology of the Pyrenean rock lizard, Iberolacerta bonnali (Squamata, Lacertidae).

We studied, at 2200m altitude, the thermal biology of the Pyrenean rock lizard, Iberolacerta bonnali, in the glacial cirque of Cotatuero (National Park of Ordesa, Huesca, Spain). The preferred thermal range (PTR) of I. bonnali indicates that it is a cold-adapted ectotherm with a narrow PTR (29.20-32.77°C). However, its PTR (3.57°C) is twice as wide as other Iberolacerta lizards, which may be explained by its broader historical distribution. The studied area is formed by a mosaic of microhabitats which offer different operative temperatures, so that lizards have, throughout their entire daily period of activity, the opportunity to choose the most thermally suitable substrates. I. bonnali achieves an effectiveness of thermoregulation of 0.95, which makes it the highest value found to date among the Lacertidae, and one of the highest among lizards. Their relatively wide distribution, their wider PTR, and their excellent ability of thermoregulation, would make I. bonnali lizards less vulnerable to climate change than other species of Iberolacerta. Thanks to its difficult access, the studied area is not visited by a large number of tourists, as are other areas of the National Park. Thus, it is a key area for the conservation of the Pyrenean rock lizard. By shuttling between suitable microhabitats, lizards achieve suitable body temperatures during all day. However, such thermally suitable microhabitats should vary in other traits than thermal quality, such as prey availability or predation risk. Hence, it seems that these not-thermal traits are not constraining habitat selection and thermoregulation in this population. Therefore, future research in this population may study the causes that would lead lizards to prioritize thermoregulation to such extent in this population.

Sexual differences in behavioral thermoregulation of the lizard Scelarcis perspicillata.

Temperature determines all aspects of the biology of ectotherms. Although sexual differences in thermal ecology are not the rule in lizards, some species exhibit such differences. We studied the effect of sex and reproductive condition on the thermoregulation of an introduced population of Scelarcis perspicillata during the summer in Menorca (Balearic Islands, Spain). These lizards live in the wall surfaces of a limestone quarry, where the sun is scarce because of the narrowness of the quarry walls. The population is sexually dimorphic, with larger males than females. We measured body temperature (Tb) of adult males and females in the field, and air (Ta) and substrate temperature (Ts) at the capture sites, and recorded exposure to sunlight, height of the perch, and type of substrate. We also recorded operative temperatures (Te) as a null hypothesis of thermoregulation. Finally, we studied the thermal preferences of adult males and females in a laboratory thermal gradient. Thermal preferences were similar for pregnant and non-pregnant females, and sex did not affect the thermal preferences of lizards, even after controlling for the effect of body size. However, in the field, females achieved higher Tb than males, and occupied microhabitats with higher Ta and Ts and lower perch heights than males. Furthermore, females selected perches in full sun at a higher frequency than males. As a consequence, females achieved a higher accuracy and effectiveness of thermoregulation (0.89) than males (0.84). Thus, all else being equal, females would achieve a higher performance than males. The observed results are attributable to sexual differences in behaviour, probably in relation with the reproductive season.

Recent Advancements towards Sustainability in Rotomoulding.

Rotational moulding is a unique low-shear process used to manufacture hollow parts. The process is an excellent process method for batch processing, minimal waste and stress-free parts. However, the process has drawbacks such as long cycle times, gas dependency and a limited palette of materials relative to other process methods. This review aimed to shed light on the current state-of-the-art research contributing towards sustainability in rotational moulding. The scope of this review broadly assessed all areas of the process such as material development, process adaptations and development, modelling, simulation and contributions towards applications carving a more sustainable society. The PRISMA literature review method was adopted, finding that the majority of publications focus on material development, specifically on the use of waste, fillers, fibres and composites as a way to improve sustainability. Significant focus on biocomposites and natural fibres highlighted the strong research interest, while recyclate studies appeared to be less explored to date. Other research paths are process modification, modelling and simulation, motivated to increase energy efficiency, reduction in scrap and attempts to reduce cycle time with models. An emerging research interest in rotational moulding is the contribution towards the hydrogen economy, particularly type IV hydrogen vessels.

Characterization of Microalgae Biomass-Based Composites Obtained through Rotational Molding.

The wide range of applications and the numerous advantages of plastics have led to their excessive use, with subsequent damage to ecosystems. As an environmentally friendly alternative, biocomposites have gained much attention, and microalgae have become a potential source for their production. In this study, the use of washed and unwashed Spirulina in polyethylene-based composites has been evaluated as a way to prevent the thermooxidation of polyethylene, while at the same time, reducing the amount of virgin plastic used. Biocomposites were produced by rotomolding, testing different biomass contents and determining their mechanical and thermal performances as well as their water uptake level. Composites with up to 15% of biomass (by weight), a particularly high ratio for rotomolding, were satisfactorily produced. Using 5% of both biomasses did not significantly modify the behavior when compared with the neat PE samples' properties. For higher loadings, the use of non-washed biomass allowed us to obtain better properties, with added benefits related to using an unwashed biomass (less water consumption, lower costs and fewer environmental impacts). On the other hand, this study showed a promising beneficial effect on the thermooxidative resistance of composites, as the oxidation induction times were notably increased with biomass addition.

Characterization of PLA Sheets Prepared by Stretching under Different Conditions: Influence of Reprocessing and Establishing Optimal Conditions.

Polylactide (PLA) is one of the most commonly used biomaterials nowadays, with many recognized benefits, particularly in the packaging and single-use products industries. However, little research has been conducted on its stretching behavior. This work investigates the optimal conditions of biaxial stretching of injection-molded PLA samples produced under different processing conditions (pressure, drying, and pre-processing by extrusion, to simulate a recycling step). The injection-molded samples were characterized to determine their mechanical, thermal and thermo-mechanical behavior, water absorption, thermal behavior, and crystallization kinetics. The extruded samples showed reduced thermal stability, lower viscosity, decreased mechanical properties, and higher crystallization rates due to thermal degradation. However, the stretched samples provided similar properties regardless of the materials pre-processing. Regarding the assessment of the biaxial stretching process, processing at lower temperatures provides the films with a higher yield and breaking strength, while the time and strain rates have little influence on such properties. It was then determined that 82 °C is the optimal temperature for stretching the PLA samples. An increase in the stretch ratio provided a higher elastic modulus and higher values of opacity due to an increased crystallinity induced by stress during the process. Films as thin as 50 µm can be obtained by biaxially stretching injection-molded preforms, producing a deformation over 150% and acquiring good mechanical properties: about 90 MPa for the yield and a breaking strength and elastic modulus of 4000 MPa.

Mechanical Performance of Rotationally Molded Multilayer mLDPE/Banana-Fiber Composites.

The incorporation of materials different from the polymer within the rotational molding process usually results in lowered mechanical properties, where impact strength is of particular concern. In order to overcome this issue, multilayer structures of virgin polyethylene (PE) and banana fiber composites were prepared to determine the impact of the different layers on the performance of the final part. Cycle time has been studied to identify the influence of the addition of fibers in the process. The tensile, flexural and impact properties have been analyzed, finding improvements in Young's modulus of up to 13%, although at the expense of significant decreases in impact strength. A reduction in the fiber size due to the pulverization process was observed, which affected the rheological and mechanical behavior of the composite. The beneficial effects of working in multiple layers have been demonstrated in this work, where composites with up to 5% of banana fiber have been produced in two-layer structures. Finally, the need to add neat polyethylene in the external layer is also highlighted as a way to counteract the reductions in mechanical properties, particularly for flexural elastic modulus and tensile strength, and this also helps with the drop in impact behavior to a lower extent.

Uncertain future for global sea turtle populations in face of sea level rise.

Sea level rise has accelerated during recent decades, exceeding rates recorded during the previous two millennia, and as a result many coastal habitats and species around the globe are being impacted. This situation is expected to worsen due to anthropogenically induced climate change. However, the magnitude and relevance of expected increase in sea level rise (SLR) is uncertain for marine and terrestrial species that are reliant on coastal habitat for foraging, resting or breeding. To address this, we showcase the use of a low-cost approach to assess the impacts of SLR on sea turtles under various Intergovernmental Panel on Climate Change (IPCC) SLR scenarios on different sea turtle nesting rookeries worldwide. The study considers seven sea turtle rookeries with five nesting species, categorized from vulnerable to critically endangered including leatherback turtles (Dermochelys coriacea), loggerhead turtles (Caretta caretta), hawksbill turtles (Eretmochelys imbricata), olive ridley turtles (Lepidochelys olivacea) and green turtles (Chelonia mydas). Our approach combines freely available digital elevation models for continental and remote island beaches across different ocean basins with projections of field data and SLR. Our case study focuses on five of the seven living sea turtle species. Under moderate climate change scenarios, by 2050 it is predicted that at some sea turtle nesting habitats 100% will be flooded, and under an extreme scenario many sea turtle rookeries could vanish. Overall, nesting beaches with low slope and those species nesting at open beaches such as leatherback and loggerheads sea turtles might be the most vulnerable by future SLR scenarios.

Extrinsic traits consistently drive microhabitat decisions of an arboreal snake, independently of sex and personality.

One pivotal topic on habitat selection is to understand the influence of intrinsic and extrinsic factors on the selection process. Although the effect of some extrinsic variables and sex has been extensively studied, almost nothing is known about the effect of personality, particularly on snakes. Here we addressed the relative importance of extrinsic (tree-related) and intrinsic (sex and personality) factors driving microhabitat selection decisions of a nocturnal tree snake (Leptodeira annulata). We implemented a protocol to quantify the influence of personality and sex on the role of extrinsic variables on microhabitat selection. First, we conducted three behavioral experiments to extract the shyness-boldness and avoidance-exploitation personality traits of male snakes. Then, we evaluated the role of sex and personality on the effect of tree-traits (thickness, canopy cover and shelter availability) on microhabitat selection, using two-step conditional logistic regression. Snakes consistently selected tree trunks, preferably thick and with high canopy cover and shelter availability, independently of their sex or personality. For this species, only extrinsic variables determined microhabitat decisions. Our protocol will aid to quantify the role of personality on microhabitat selection of other species and understand whether this is an important variable in habitat decision-making or not.

Recent Developments in Inorganic Composites in Rotational Molding.

Rotational molding allows for obtaining hollow parts with good aesthetics and properties, having as main drawbacks the lack of pressure and the long cycle times, which limit the range of materials. Different fillers have been introduced in rotomolding to obtain composite materials assessed. This review has shown that glass fibers or particles are the most common material among them, although carbon fibers or clays have also been studied. In general terms, 10% loadings provide an increase in mechanical properties; higher loadings usually lead to a decrease in processability or final properties. When the filler consists of a micro- or nano-material, such as clay or graphene, lower loadings are proposed, generally not exceeding 3%. The use of fillers of an inorganic nature to obtain composites has not been as explored as the incorporation of lignocellulosic materials and even less if referring to waste materials or side streams from industrial processes. So, there is a broad field for assessing the processing and properties of rotomolded composites containing inorganic waste materials, including the study of the relationship between the ratio of filler/reinforcement and the final properties and also their preprocessing (dry blending vs. melting compounding).

The role of environmental temperature on movement patterns of giant anteaters.

Mammals can show conspicuous behavioral responses to thermal variation, including changes in movement patterns. We used an integrative approach to understand how environmental temperature can drive the movement behavior of a mammal with low capacity for physiological thermoregulation, the giant anteater (Myrmecophaga tridactyla). We tracked 52 giant anteaters in 7 areas throughout the Brazilian savannah. We estimated the distance moved, area used, use of forest areas, and mean environmental temperature for each monitoring day of each individual. We modeled these data with Mixed Structural Equations - considering the possible interactions between our variables and controlling for sex and body mass. Giant anteaters reduced displacement and increased forest use with decreasing environmental temperature, probably because of their low body heat production. It is possible that they reduce distance moved and area used by reducing the duration of activity. With decreasing temperature, forest habitats become warmer than open ones, besides buffer rain and chilly winds. Reducing displacement and using forests are important strategies to reduce body heat loss and the energetic costs of thermoregulation. However, decreasing movement can limit food access and, consequently, fitness. Therefore, we highlight the importance of forests as thermal shelters. With increasing frequency and intensity of extreme weather events, we showed the need to preserve forest patches to offer suitable conditions for tropical mammals' behavioral thermoregulation. In this context, policies favoring deforestation on Brazilian territory are especially worrisome. Finally, we emphasize the need of integrative approaches to understand the complex interactions between organisms and the environment.

Are Natural-Based Composites Sustainable?

This paper assesses the aspects related to sustainability of polymer composites, focusing on the two main components of a composite, the matrix and the reinforcement/filler. Most studies analyzed deals with the assessment of the composite performance, but not much attention has been paid to the life cycle assessment (LCA), biodegradation or recyclability of these materials, even in those papers containing the terms "sustainable" (or its derivate words), "green" or "eco". Many papers claim about the sustainable or renewable character of natural fiber composites, although, again, analysis about recyclability, biodegradation or carbon footprint determination of these materials have not been studied in detail. More studies focusing on the assessment of these composites are needed in order to clarify their potential environmental benefits when compared to other types of composites, which include compounds not obtained from biological resources. LCA methodology has only been applied to some case studies, finding enhanced environmental behavior for natural fiber composites when compared to synthetic ones, also showing the potential benefits of using recycled carbon or glass fibers. Biodegradable composites are considered of lesser interest to recyclable ones, as they allow for a higher profitability of the resources. Finally, it is interesting to highlight the enormous potential of waste as raw material for composite production, both for the matrix and the filler/reinforcement; these have two main benefits: no resources are used for their growth (in the case of biological materials), and fewer residues need to be disposed.

Valorization of Invasive Plants from Macaronesia as Filler Materials in the Production of Natural Fiber Composites by Rotational Molding.

This paper compares the mechanical properties of different natural fiber composites produced by rotational molding as a way of waste valorization from campaigns to control invasive plant species in Macaronesia. Rotomolded parts produced with polymeric matrices (polyethylene) and filled with up to 20% by weight of cellulosic fibers obtained from Arundo donax L., Pennisetum setaceum, and Ricinus communis plants were characterized in terms of tensile, flexural, and impact strength. It was found that the sieving of natural fibers allowed for their introduction in higher loadings, from 10 (for un-sieved material) to 20%; fiber size greatly affected the mechanical properties of the final parts, although some combinations were proven not to reduce the mechanical properties of the neat resin. This study is a first approach to the valorization of residues obtained from periodic campaigns of the control of invasive species performed by public authorities, usually at the local level. It is important to highlight that the main objective of this research did not focus on economically profitable activity; instead, it was focused on the reduction of wastes to be disposed from ecosystem maintenance actions and the investment of potential income into preservation policies.

Environmental Hazards of Giant Reed (Arundo donax L.) in the Macaronesia Region and Its Characterisation as a Potential Source for the Production of Natural Fibre Composites.

This paper summarises the results obtained from the characterisation of giant reed (Arundo donax L.) plant and fibres. The research is part of a project developed in the Macaronesia region, of which the aim is to demonstrate the feasibility of using biomass from invasive plant species in the composites sector as a way of financing control campaigns and habitats conservation labours. An experimental procedure for the extraction of fibre bundles from this plant was developed, and the material obtained was characterised in terms of chemical composition, thermogravimetry and infrared spectra to evaluate its potential application in the production of polymeric composite materials as a strategy for the valorisation of residual biomass from this invasive species in Macaronesia. Thermoplastic matrix composites with fibre content up to 40 wt.% were produced and their mechanical properties under tensile, flexural and impact loading were determined. No references on the preparation of composite materials with polyolefin matrices and giant reed fibres have been found. Results obtained from mechanical tests show a good performance of the manufactured composites, with a significant increase in both flexural and tensile stiffness; the flexural modulus is almost tripled for PE-based composites and rises to 88% with respect to PP matrix. The ultimate flexural strength and the tensile and flexural yield strength are kept at acceptable values compared to neat polymer materials, although ultimate tensile strength and impact resistance are significantly affected when natural fibres are added.

Opuntia spp. Fibre Characterisation to Obtain Sustainable Materials in the Composites Field.

Some studies have evaluated the use of Opuntia as reinforcement for polymeric matrices, obtaining good results in energy absorption tests and increasing the tensile elastic modulus. However, no studies focusing on the previous characterisation of the fibres and their treatment to improve compatibility with polymeric matrices have been found. This work analyses the chemical composition of Opuntia maxima (OM) and Opuntia dillenii (OD) cladodes and fibre, studying how different treatments influence it. AOAC 2000 methods were used to determine non-structural components and the Van Soest method was used to estimate structural components. Surface characteristics of the samples were also evaluated by Fourier Transform Infrared Spectroscopy (FTIR). Opuntia fibre presented higher cellulose (50-66%) and lignin (6-14%) content and lower hemicellulose (8-13%) content than Opuntia cladodes (9-14% cellulose, 20-50% hemicellulose, 1-4% lignin). Despite the variability of lignocellulosic materials, OD cladodes treated with water and acetic acid achieved an increase in the structural components. Alkaline fibre treatment removed pectin and hemicellulose from the fibre surface, slightly increasing the cellulose content. Future research should evaluate whether the treated Opuntia fibre can improve the mechanical properties of reinforced polymer.

An annual study on plastic accumulation in surface water and sediment cores from the coastline of Tenerife (Canary Island, Spain).

Sediment core samples from high tide lines and in submerged zones as well as surface water samples from eight beaches of Tenerife were analysed. Sampling was conducted over a period of one year in intervals of 5 weeks. The majority of particles were found in the high tide sediment (66%), followed by water samples (23%) and finally in sediment from submerged zones (11%). Regarding the particle amount per volume (items/L), accumulation in sediment samples was statistically higher compared to water samples. Mean values of items/L were higher in high tide sediments. In high tide and water samples, mostly white and transparent particles >1 mm were found. More than 70% were represented by fragments. In sediments from submerged zones, yellow and blue microparticles (<1 mm) were predominant and 61.9% consisted of fibres. Larger particles were mainly identified as PP, PE, PS, PTFE and PVC, while polymer types of smaller particles were more variable.