Geometric light trapping with a V-trap for efficient organic solar cells.

The efficiency of today's most efficient organic solar cells is primarily limited by the ability of the active layer to absorb all the sunlight. While internal quantum efficiencies exceeding 90% are common, the external quantum efficiency rarely exceeds 70%. Light trapping techniques that increase the ability of a given active layer to absorb light are common in inorganic solar cells but have only been applied to organic solar cells with limited success. Here, we analyze the light trapping mechanism for a cell with a V-shape substrate configuration and demonstrate significantly improved photon absorption in an 5.3%-efficient PCDTBT:PC(70)BM bulk heterojunction polymer solar cell. The measured short circuit current density improves by 29%, in agreement with model predictions, and the power conversion efficiency increases to 7.2%, a 35% improvement over the performance in the absence of a light trap.

Resonant cavity enhanced light harvesting in flexible thin-film organic solar cells.

Dielectric/metal/dielectric (DMD) electrodes have the potential to significantly increase the absorption efficiency and photocurrent in flexible organic solar cells. We demonstrate that this enhancement is attributed to a broadband cavity resonance. Silver-based semitransparent DMD electrodes with sheet resistances below 10 ohm/sq. are fabricated on flexible polyethylene terephthalate (PET) substrates in a high-throughput roll-to-roll sputtering tool. We carefully study the effect of the semitransparent DMD electrode (here composed of Zn(x)Sn(y)O(z)/Ag/In(x)Sn(y)O(z)) on the optical device performance of a copper phthalocyanine (CuPc)/fullerene (C60) bilayer cell and illustrate that a resonant cavity enhanced light trapping effect dominates the optical behavior of the device.

Exhaled breath SARS-CoV-2 shedding patterns across variants of concern.

OBJECTIVES: We performed exhaled breath (EB) and nasopharyngeal (NP) quantitative polymerase chain reaction (qPCR) and NP rapid antigen testing (NP RAT) of SARS-CoV-2 infections with different variants. METHODS: We included immuno-naïve alpha-infected (n = 11) and partly boosted omicron-infected patients (n = 8) as high-risk contacts. We compared peak NP and EB qPCR cycle time (ct) values between cohorts (Wilcoxon-Mann-Whitney test). Test positivity was compared for three infection phases using Cochran Q test. RESULTS: Peak median NP ct was 11.5 (interquartile range [IQR] 10.1-12.1) for alpha and 12.2 (IQR 11.1-15.3) for omicron infections. Peak median EB ct was 25.2 (IQR 24.5-26.9) and 28.3 (IQR 26.4-30.8) for alpha and omicron infections, respectively. Distributions did not differ between cohorts for NP (P = 0.19) or EB (P = 0.09). SARS-CoV-2 shedding peaked on day 1 in EB (confidence interval [CI] 0.0 - 4.5) and day 3 in NP (CI 1.5 - 6.0). EB qPCR positivity equaled NP qPCR positivity on D0-D1 (P = 0.44) and D2-D6 (P = 1.0). It superseded NP RAT positivity on D0-D1 (P = 0.003) and D2-D6 (P = 0.008). It was inferior to both on D7-D10 (P < 0.001). CONCLUSION: Peak EB and nasopharynx shedding were comparable across variants. EB qPCR positivity matched NP qPCR and superseded NP RAT in the first week of infection.

Molecular detection of SARS-COV-2 in exhaled breath at the point-of-need.

The SARS-CoV-2 pandemic has highlighted the need for improved technologies to help control the spread of contagious pathogens. While rapid point-of-need testing plays a key role in strategies to rapidly identify and isolate infectious patients, current test approaches have significant shortcomings related to assay limitations and sample type. Direct quantification of viral shedding in exhaled particles may offer a better rapid testing approach, since SARS-CoV-2 is believed to spread mainly by aerosols. It assesses contagiousness directly, the sample is easy and comfortable to obtain, sampling can be standardized, and the limited sample volume lends itself to a fast and sensitive analysis. In view of these benefits, we developed and tested an approach where exhaled particles are efficiently sampled using inertial impaction in a micromachined silicon chip, followed by an RT-qPCR molecular assay to detect SARS-CoV-2 shedding. Our portable, silicon impactor allowed for the efficient capture (>85%) of respiratory particles down to 300 nm without the need for additional equipment. We demonstrate using both conventional off-chip and in-situ PCR directly on the silicon chip that sampling subjects' breath in less than a minute yields sufficient viral RNA to detect infections as early as standard sampling methods. A longitudinal study revealed clear differences in the temporal dynamics of viral load for nasopharyngeal swab, saliva, breath, and antigen tests. Overall, after an infection, the breath-based test remains positive during the first week but is the first to consistently report a negative result, putatively signalling the end of contagiousness and further emphasizing the potential of this tool to help manage the spread of airborne respiratory infections.

Semitransparent organic photovoltaic cells with laminated top electrode.

We demonstrate semitransparent small molecular weight organic photovoltaic cells using a laminated silver nanowire mesh as a transparent, conductive cathode layer. The lamination process does not damage the underlying solar cell and results in a transparent electrode with low sheet resistance and high optical transmittance without impacting photocurrent collection. The resulting semitransparent phthalocyanine/fullerene organic solar cell has a power conversion efficiency that is 57% of that of a device with a conventional metal cathode due to differences in optical absorption.

The origin of enhanced optical absorption in solar cells with metal nanoparticles embedded in the active layer.

We analyze the enhancement in optical absorption of an absorbing medium when spherical metal nanoparticles are embedded in it. Our analysis uses generalized Mie theory to calculate the absorbed optical power as a function of the distance from the metal nanoparticle. This analysis is used to evaluate the potential of enhancing optical absorption in thin-film solar cells by embedding spherical metal nanoparticles. We consider the trade-off between maximizing overall optical absorption and ensuring that a large fraction of the incident optical power is dissipated in the absorbing host medium rather than in the metal nanoparticle. We show that enhanced optical absorption results from strong scattering by the metal nanoparticle which locally enhances the optical electric fields. We also discuss the effect of a thin dielectric encapsulation of the metal nanoparticles.

High performance solar-selective absorbers using coated sub-wavelength gratings.

Spectral control of the emissivity of surfaces is essential for efficient conversion of solar radiation into heat. We investigated surfaces consisting of sub-wavelength V-groove gratings coated with aperiodic metal-dielectric stacks. The spectral behavior of the coated gratings was modeled using rigorous coupled-wave analysis (RCWA). The proposed absorber coatings combine impedance matching using tapered metallic features with the excellent spectral selectivity of aperiodic metal-dielectric stacks. The aspect ratio of the V-groove can be tailored in order to obtain the desired spectral selectivity over a wide angular range. Coated V-groove gratings with optimal aspect ratio are predicted to have thermal emissivity below 6% at 720K while absorbing >94% of the incident light. These sub-wavelength gratings would have the potential to significantly increase the efficiency of concentrated solar thermal systems.

Optimal light trapping in ultra-thin photonic crystal crystalline silicon solar cells.

Crystalline silicon is an attractive photovoltaic material because of its natural abundance, accumulated materials and process knowledge, and its appropriate band gap. To reduce cost, thin films of crystalline silicon can be used. This reduces the amount of material needed and allows material with shorter carrier diffusion lengths to be used. However, the indirect band gap of silicon requires that a light trapping approach be used to maximize optical absorption. Here, a photonic crystal (PC) based approach is used to maximize solar light harvesting in a 400 nm-thick silicon layer by tuning the coupling strength of incident radiation to quasiguided modes over a broad spectral range. The structure consists of a double layer PC with the upper layer having holes which have a smaller radius compared to the holes in the lower layer. We show that the spectrally averaged fraction of photons absorbed is increased 8-fold compared to a planar cell with equivalent volume of active material. This results in an enhancement of maximum achievable photocurrent density from 7.1 mA/cm(2) for an unstructured film to 21.8 mA/cm(2) for a film structured as the double layer photonic crystal. This photocurrent density value approaches the limit of 26.5 mA/cm(2), obtained using the Yablonovitch light trapping limit for the same volume of active material.

Efficient bulk heterojunction photovoltaic cells using small-molecular-weight organic thin films.

The power conversion efficiency of small-molecular-weight and polymer organic photovoltaic cells has increased steadily over the past decade. This progress is chiefly attributable to the introduction of the donor-acceptor heterojunction that functions as a dissociation site for the strongly bound photogenerated excitons. Further progress was realized in polymer devices through use of blends of the donor and acceptor materials: phase separation during spin-coating leads to a bulk heterojunction that removes the exciton diffusion bottleneck by creating an interpenetrating network of the donor and acceptor materials. The realization of bulk heterojunctions using mixtures of vacuum-deposited small-molecular-weight materials has, on the other hand, posed elusive: phase separation induced by elevating the substrate temperature inevitably leads to a significant roughening of the film surface and to short-circuited devices. Here, we demonstrate that the use of a metal cap to confine the organic materials during annealing prevents the formation of a rough surface morphology while allowing for the formation of an interpenetrating donor-acceptor network. This method results in a power conversion efficiency 50 per cent higher than the best values reported for comparable bilayer devices, suggesting that this strained annealing process could allow for the formation of low-cost and high-efficiency thin film organic solar cells based on vacuum-deposited small-molecular-weight organic materials.

Design of wide-angle solar-selective absorbers using aperiodic metal-dielectric stacks.

Spectral control of the emissivity of surfaces is essential in applications such as solar thermal and thermophotovoltaic energy conversion in order to achieve the highest conversion efficiencies possible. We investigated the spectral performance of planar aperiodic metal-dielectric multilayer coatings for these applications. The response of the coatings was optimized for a target operational temperature using needle-optimization based on a transfer matrix approach. Excellent spectral selectivity was achieved over a wide angular range. These aperiodic metal-dielectric stacks have the potential to significantly increase the efficiency of thermophotovoltaic and solar thermal conversion systems. Optimal coatings for concentrated solar thermal conversion were modeled to have a thermal emissivity <7% at 720K while absorbing >94% of the incident light. In addition, optimized coatings for solar thermophotovoltaic applications were modeled to have thermal emissivity <16% at 1750K while absorbing >85% of the concentrated solar radiation.

Broadband optical absorption enhancement through coherent light trapping in thin-film photovoltaic cells.

We show that optical absorption in thin-film photovoltaic cells can be enhanced by inserting a tuned two-component aperiodic dielectric stack into the device structure. These coatings are a generalization and unification of the concepts of an anti-reflection coating used in solar cells and high-reflectivity distributed Bragg mirror used in resonant cavity-enhanced narrowband photodetectors. Optimized two-component coatings approach the physically realizable limit and optimally redistribute the spectral photon density-of-states to enhance the absorption of the active layer across its absorption spectrum. Specific designs for thin-film organic solar cells increase the photocurrent under AM1.5 illumination, averaged over all incident angles and polarizations, by up to 40%.

The optical advantages of curved focal plane arrays.

The design of optical systems for digital cameras is complicated by the requirement that the image surface be planar, which results in complex and expensive optics. We analyze a compact optical system with a curved image surface and compare its performance to systems with planarimage surfaces via optics analysis and image system simulation. Our analysis shows that a curved image surface provides a way to lower the number of optical elements, reduce aberrations including astigmatism and coma, and increase off-axis brightness and sharpness. A method to fabricate curved image focal plane arrays using monolithic silicon is demonstrated.

Design of non-periodic dielectric stacks for tailoring the emission of organic lighting-emitting diodes.

The majority of photons emitted in organic light-emitting diodes are either trapped in the substrate or emitted into lossy waveguided modes. We show how optimized, non-periodic dielectric stacks inserted between the substrate and transparent anode can be used to improve the photon outcoupling efficiency by tailoring of the local photon density of states. Unlike previously demonstrated outcoupling schemes, this method does not lead to pixel blurring and maintains a Lambertian angular emission profiles within a specified cone. For small molecular weight, green-emitting devices, a 2.5-fold uniformly distributed increase in brightness is achievable for a viewing angle of 60 degrees .

Three-part differential of unlabeled leukocytes with a compact lens-free imaging flow cytometer.

A compelling clinical need exists for inexpensive, portable haematology analyzers that can be utilized at the point-of-care in emergency settings or in resource-limited settings. Development of a label-free, microfluidic blood analysis platform is the first step towards such a miniaturized, cost-effective system. Here we assemble a compact lens-free in-line holographic microscope and employ it to image blood cells flowing in a microfluidic chip, using a high-speed camera and stroboscopic illumination. Numerical reconstruction of the captured holograms allows classification of unlabeled leukocytes into three main subtypes: lymphocytes, monocytes and granulocytes. A scale-space recognition analysis to evaluate cellular size and internal complexity is also developed and used to build a 3-part leukocyte differential. The lens-free image-based classification is compared to the 3-part white blood cell differential generated by using a conventional analyzer on the same blood sample and is found to be in good agreement with it.

Solution processed zinc oxide nanopyramid/silver nanowire transparent network films with highly tunable light scattering properties.

Metal nanowire transparent networks are promising replacements to indium tin oxide (ITO) transparent electrodes for optoelectronic devices. While the transparency and sheet resistance are key metrics for transparent electrode performance, independent control of the film light scattering properties is important to developing multifunctional electrodes for improved photovoltaic absorption. Here we show that controlled incorporation of ZnO nanopyramids into a metal nanowire network film affords independent, highly tunable control of the scattering properties (haze) with minimal effects on the transparency and sheet resistance. Varying the zinc oxide/silver nanostructure ratios prior to spray deposition results in sheet resistances, transmission (600 nm), and haze (600 nm) of 6-30 Ω â–¡(-1), 68-86%, and 34-66%, respectively. Incorporation of zinc oxide nanopyramid scattering agents into the conducting nanowire mesh has a negligible effect on mesh connectivity, providing a straightforward method of controlling electrode scattering properties. The decoupling of the film scattering power and electrical characteristics makes these films promising candidates for highly scattering transparent electrodes in optoelectronic devices and can be generalized to other metal nanowire films as well as carbon nanotube transparent electrodes.

Ion-pair reversed-phase chromatography of short double-stranded deoxyribonucleic acid in silicon micro-pillar array columns: retention model and applications.

Separation of double-stranded (ds) DNAs is important in numerous biochemical analyses relevant for clinical applications. A widely used separation technique is high performance liquid chromatography (HPLC), in the variant of ion-pair reversed-phase (IP-RP) chromatography. HPLC can be miniaturized by means of silicon micro-pillar array columns leading to on-chip fast and high resolution dsDNA separation with limited sample quantity. However, theoretical studies of retentive behavior of dsDNA in miniaturized chromatographic columns are hardly available, despite their enormous practical relevance. This paper established a new retention model to describe the size dependent separation of dsDNAs for any characteristic of the linear mobile phase gradient, in analogy to the model used to describe the retention of polymer chains with repeating units in RP HPLC. The model agrees with a large amount of dsDNA retention data, measured using DNA molecules in the size range of 10-400 base pairs in columns with different lengths (2 and 40cm) and different micro-pillar sizes (2 and 2.5µm in diameter), in various mobile phase gradients. The model is particularly useful in practice, since it requires no numerical solutions and the column-specific fitting parameters (4 or 5) can be determined in a limited number of separation runs. As examples of its applications, the model has been used for the optimization of dsDNA step-gradient separations (5 dsDNAs separated within 8min) and for the determination of the size of dsDNA fragment (with uncertainty of about 2%). These applications are especially relevant for on-chip DNA analysis devices.

Color in the corners: ITO-free white OLEDs with angular color stability.

High-efficiency white OLEDs fabricated on silver nanowire-based composite transparent electrodes show almost perfectly Lambertian emission and superior angular color stability, imparted by electrode light scattering. The OLED efficiencies are comparable to those fabricated using indium tin oxide. The transparent electrodes are fully solution-processable, thin-film compatible, and have a figure of merit suitable for large-area devices.

Open-cell recording of action potentials using active electrode arrays.

The investigation of complex communication in cellular networks requires superior measurement tools than those available to date. Electrode arrays integrated onto silicon electronics are increasingly used to measure the electrical activity of cells in an automated and highly parallelized fashion, but they are restricted to recording extracellular potentials. Here, we report on an array of TiN electrodes built using standard silicon electronics for intracellular action potential recording. Intracellular access, possible at each of the 16 384 electrodes on the chip, was accomplished by local membrane electroporation using electrical stimulation with subcellular, micrometer-sized electrodes. Access to the cell interior was transient and could be tuned in duration by adapting the electroporation protocol. Intracellular sensing was found to be minimally invasive in the short and long-term, allowing consecutive intracellular recordings from the same cell over the course of days. Finally, we applied this method to investigate the effect of an ion channel blocker on cardiac electrical activity. This technique opens the door to massively parallel, long-term intracellular recording for fundamental electrophysiology and drug screening.

Fully solution-processed inverted polymer solar cells with laminated nanowire electrodes.

We demonstrate organic photovoltaic cells in which every layer is deposited by solution processing on opaque metal substrates, with efficiencies similar to those obtained in conventional device structures on transparent substrates. The device architecture is enabled by solution-processed, laminated silver nanowire films serving as the top transparent anode. The cells are based on the regioregular poly(3-hexylthiophene) and C(61) butyric acid methyl ester bulk heterojunction and reach an efficiency of 2.5% under 100 mW/cm(2) of AM 1.5G illumination. The metal substrates are adequate barriers to moisture and oxygen, in contrast to transparent plastics that have previously been used, giving rise to the possibility of roll-to-roll solution-processed solar cells that are packaged by lamination to glass substrates, combining the cost advantage of roll-to-roll processing with the barrier properties of glass and metal foil.

Scalable coating and properties of transparent, flexible, silver nanowire electrodes.

We report a comprehensive study of transparent and conductive silver nanowire (Ag NW) electrodes, including a scalable fabrication process, morphologies, and optical, mechanical adhesion, and flexibility properties, and various routes to improve the performance. We utilized a synthesis specifically designed for long and thin wires for improved performance in terms of sheet resistance and optical transmittance. Twenty Omega/sq and approximately 80% specular transmittance, and 8 ohms/sq and 80% diffusive transmittance in the visible range are achieved, which fall in the same range as the best indium tin oxide (ITO) samples on plastic substrates for flexible electronics and solar cells. The Ag NW electrodes show optical transparencies superior to ITO for near-infrared wavelengths (2-fold higher transmission). Owing to light scattering effects, the Ag NW network has the largest difference between diffusive transmittance and specular transmittance when compared with ITO and carbon nanotube electrodes, a property which could greatly enhance solar cell performance. A mechanical study shows that Ag NW electrodes on flexible substrates show excellent robustness when subjected to bending. We also study the electrical conductance of Ag nanowires and their junctions and report a facile electrochemical method for a Au coating to reduce the wire-to-wire junction resistance for better overall film conductance. Simple mechanical pressing was also found to increase the NW film conductance due to the reduction of junction resistance. The overall properties of transparent Ag NW electrodes meet the requirements of transparent electrodes for many applications and could be an immediate ITO replacement for flexible electronics and solar cells.