RESUMEN
Because of its high specific capacity and superior rate performance, porous carbon is regarded as a potential anode material for lithium-ion batteries (LIBs). However, porous carbon materials with wide pore diameter distributions suffer from low structural stability and low electrical conductivity during the application process. During this study, the calcium carbonate nanoparticle template method is used to prepare coal tar pitch-derived porous carbon (CTP-X). The coal tar pitch-derived porous carbon has a well-developed macroporous-mesoporous-microporous hierarchical porous network structure, which provides abundant active sites for Li+ storage, significantly reduces polarization and charge transfer resistance, shortens the diffusion path and promotes the rapid transport of Li+. More specifically, the CTP-2 anode shows high charge capacity (496.9â mAh g-1 at 50â mA g-1), excellent rate performance (413.6â mAh g-1 even at 500â mA g-1), and high cycling stability (capacity retention rate of about 100 % after 1,000 cycles at 2â A g-1). The clean and eco-friendly large-scale utilization of coal tar pitch will facilitate the development of high-performance anodes in the field of LIBs.
RESUMEN
The stability and resilience of an anaerobic ammonium oxidation (anammox) system under transient nanoscale Zero-Valent Iron (nZVI) (50, 75 and 100â¯mgâ¯L-1), hydraulic shock (2-fold increase in flow rate) and their combination were studied in an up-flow anaerobic sludge blanket reactor. The response to the shock loads can be divided into three phases i.e. shock, inertial and recovery periods. The effects of the shock loads were directly proportional to the shock intensity. The effluent quality was gradually deteriorated after exposure to high nZVI level (100â¯mgâ¯L-1) for 2â¯h. The higher effluent sensitivity index and response caused by unit intensity of shock was observed under hydraulic and combined shocks. Notably, the specific anammox activity and the content of heme c were considerably reduced during the shock phase and the maximum loss rates were about 30.5% and 24.8%, respectively. Nevertheless, the extracellular polymeric substance amount in the shock phase was enhanced in varying degrees and variation tendency was disparate at all the tested shock loads. These results suggested that robustness of the anammox system was dependent on the magnitude shocks applied and the reactor resistance can be improved by reducing hydraulic retention time with the increase of nZVI concentration under these circumstances.
Asunto(s)
Hierro/química , Aguas Residuales , Reactores Biológicos , Aguas del Alcantarillado , Purificación del AguaRESUMEN
Ternary transition metal oxides (TMOs) are deemed as promising anode materials of Li-ion batteries (LIBs) owing to their large theoretical capacity and rich redox reaction. Nevertheless, the inherent semiconductor characteristic and enormous volume variation of TMOs during cycling bring about sluggish reaction kinetics, fast capacity fading, and poor rate capability. In this study, three-dimensional (3D) porous CoNiO2@CTP architectures, i.e., CoNiO2 microspheres combined with coal tar pitch-derived porous carbon, were designed and synthesized through a one-step hydrothermal method followed by a heat treatment process for the first time. The microsphere morphology increases the contact area between the anode and electrolyte, shortens the transport distance of Li+ ions, and reduces the agglomeration. The existence of the CTP layer provides rich charge transmission paths, improves the electronic conductivity of CoNiO2 and provides abundant active sites for Li+ storage. Owing to the synergistic effect of porous carbon and microsphere morphology of CoNiO2, the CoNiO2@CTP (10.0 wt%) anode shows remarkable electrochemical performance with a high charge capacity (1437.5 mA h g-1 at 500 mA g-1), good rate performance (839.76 mA h g-1 even at 1 A g-1), and remarkable cycle durability (741.4 mA h g-1 after 1000 cycles at 1 A g-1), which is significantly better than pristine CoNiO2. This study not only provides a simple strategy for high-value utilization of CTP but also offers cost-effective CoNiO2@CTP architectures for high-performance LIBs.
RESUMEN
In this work, a rational design and construction of porous spherical NiO@NiMoO4 wrapped with PPy was reported for the application of high-performance supercapacitor (SC). The results show that the NiMoO4 modification changes the morphology of NiO, and the hollow internal morphology combined with porous outer shell of NiO@NiMoO4 and NiO@NiMoO4@PPy hybrids shows an increased specific surface area (SSA), and then promotes the transfer of ions and electrons. The shell of NiMoO4 and PPy with high electronic conductivity decreases the charge-transfer reaction resistance of NiO, and then improves the electrochemical kinetics of NiO. At 20Ag-1, the initial capacitances of NiO, NiMoO4, NiO@NiMoO4 and NiO@NiMoO4@PPy are 456.0, 803.2, 764.4 and 941.6Fg-1, respectively. After 10,000 cycles, the corresponding capacitances are 346.8, 510.8, 641.2 and 904.8Fg-1, respectively. Especially, the initial capacitance of NiO@NiMoO4@PPy is 850.2Fg-1, and remains 655.2Fg-1 with a high retention of 77.1% at 30Ag-1 even after 30,000 cycles. The calculation result based on density function theory shows that the much stronger Mo-O bonds are crucial for stabilizing the NiO@NiMoO4 composite, resulting in a good cycling stability of these materials.