Electromagnetic interference shielding of segregated polymer composite with an ultralow loading of in situ thermally reduced graphene oxide.

An in situ thermally reduced graphene/polyethylene conductive composite with a segregated structure was fabricated, which achieved a high electromagnetic interference shielding effectiveness of up to 28.3-32.4 dB at an ultralow graphene loading of 0.660 vol.%. Our work suggests a new way of effectively using graphene.

Temperature dependence of graphene oxide reduced by hydrazine hydrate.

Graphene oxide (GO) was successfully prepared by a modified Hummer's method. The reduction effect and mechanism of the as-prepared GO reduced with hydrazine hydrate at different temperatures and time were characterized by x-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), elemental analysis (EA), x-ray diffractions (XRD), Raman spectroscopy and thermo-gravimetric analysis (TGA). The results showed that the reduction effect of GO mainly depended on treatment temperature instead of treatment time. Desirable reduction of GO can only be obtained at high treatment temperature. Reduced at 95 °C for 3 h, the C/O atomic ratio of GO increased from 3.1 to 15.1, which was impossible to obtain at low temperatures, such as 80, 60 or 15 °C, even for longer reduction time. XPS, 13C NMR and FTIR results show that most of the epoxide groups bonded to graphite during the oxidation were removed from GO and form the sp(2) structure after being reduced by hydrazine hydrate at high temperature (>60 °C), leading to the electric conductivity of GO increasing from 1.5 × 10(-6) to 5 S cm(-1), while the hydroxyls on the surface of GO were not removed by hydrazine hydrate even at high temperature. Additionally, the FTIR, XRD and Raman spectrum indicate that the GO reduced by hydrazine hydrate can not be entirely restored to the pristine graphite structures. XPS and FTIR data also suggest that carbonyl and carboxyl groups can be reduced by hydrazine hydrate and possibly form hydrazone, but not a C = C structure.

Facile synthesis of chitosan-based acid-resistant composite films for efficient selective adsorption properties towards anionic dyes.

To effectively and selectively remove toxic anionic dyes which are heavily discharged and to promote them recovery, a sustainable cellulose nanofiber/chitosan (CNF/CS) composite film was elaborately designed through a facile procedure. Based on the strong supporting effect of CNF and excellent compatibility between CNF and CS, the composite film presents low swelling and acid-proof properties, which can prevent the adsorption process from the disintegration of adsorbent. Moreover, the positive electrical property of CNF/CS film increases the discrepancy in adsorption capacities for anionic and cationic dyes. The maximum adsorption capacity of anionic methyl orange (MO) on CNF/CS film reaches 655.23 mg/g with a desirable recyclability. The adsorption behavior attributed to a physico-chemical and monolayer adsorption process. This work opens a new route for the development of eco-friendly and highly efficient adsorbents on selective removal and recycling of anionic dyes from wastewater.

A Highly Sensitive and Broad-Range Pressure Sensor Based on Polyurethane Mesodome Arrays Embedded with Silver Nanowires.

The pressure sensor with high sensitivity and a broad pressure sensing range is highly desired for flexible electronics. Here, a high-performance pressure sensor based on a hybrid structure was facilely fabricated using the glass template method, which consists of polyurethane (PU) mesodomes embedded with gradient-distributed silver nanowire (AgNW). Such a novel hybrid architecture enables the as-prepared PU/AgNW pressure sensor to have high sensitivity as well as a wide detection range. Moreover, the obtained PU/AgNW pressure sensors have a fast response time (20 ms), good cycling stability, and excellent flexibility. The pressure sensor, benefiting from its outstanding comprehensive sensing performance, can be used for expression recognition and human activity monitoring, showing tremendous application potential in wearable devices. The proposed architecture and developed methodology in this work is promising for future flexible electronic applications.

Highly Bendable and Durable Waterproof Paper for Ultra-High Electromagnetic Interference Shielding.

An efficient electromagnetic interference (EMI) shielding paper with excellent water repellency and mechanical flexibility has been developed, by assembling silver nanowires (AgNWs) and hydrophobic inorganic ceramic on the cellulose paper, via a facile dip-coating preparation. Scanning electron microscope (SEM) observations confirmed that AgNWs were interconnected and densely coated on both sides of the cellulose fiber, which endows the as-prepared paper with high conductivity (33.69 S/cm in-plane direction) at a low AgNW area density of 0.13 mg/cm2. Owing to multiple reflections and scattering between the two outer highly conductive surfaces, the obtained composite presented a high EMI shielding effectiveness (EMI SE) of up to 46 dB against the X band, and ultrahigh specific EMI SE of 271.2 dB mm-1. Moreover, the prepared hydrophobic AgNW/cellulose (H-AgNW/cellulose) composite paper could also maintain high EMI SE and extraordinary waterproofness (water contact angle > 140°) by suffering dozens of bending tests or one thousand peeling tests. Overall, such a multifunctional paper might have practical applications in packaging conductive components and can be used as EMI shielding elements in advanced application areas, even under harsh conditions.

Highly Sensitive and Stretchable Polyurethane Fiber Strain Sensors with Embedded Silver Nanowires.

Flexible strain sensors have attracted a great amount of attention for promising applications in next-generation artificially intelligent devices. However, it is difficult for conventional planar strain sensors to meet the requirements of miniature size and light weight for flexible electronics. Herein, a highly sensitive and stretchable fiber strain sensor with a millimeter diameter was innovatively fabricated by the capillary tube method to integrate silver nanowires (AgNWs) in polyurethane (PU) fibers. Scanning electron microscopy results demonstrate that AgNWs were embedded into the surface layer of PU fibers and formed completely conductive networks. The unique AgNW networks endow the PU/AgNW fibers with superior electrical conductivity of 3.1 S/cm, high elongation at break of 265%, wide response range of 43%, high gauge factor of 87.6 up to 22% strain, fast response time of 49 ms, and excellent reliability and stability. Such satisfactory stretchability and sensitivity is attributed to the combination of the highly stretchable PU matrix and the embedded architecture of the AgNW conductive network. Moreover, PU/AgNW fibers can be employed as wearable devices to detect various human motions and to drive light-emitting diodes at a lower voltage (2.7 V).

Hydrophobic Graphene Oxide as a Promising Barrier of Water Vapor for Regenerated Cellulose Nanocomposite Films.

Regenerated cellulose (RC) films exhibit poor water barrier performance, which seriously restricts its applications. To address this issue, an impermeable and hydrophobic graphene oxide modified by chemically grafting octadecylamine (GO-ODA) was utilized to enhance the water vapor barrier performance of RC nanocomposite films. Compared to the neat RC film, more than 20% decrease in the coefficient of water vapor permeability (P H2O) was achieved by loading only 2.0 wt % GO-ODA. The promising hydrophobicity of GO-ODA effectively retarded the formation of hydrogen bonding at the relatively weakened interface between GO and RC, compensating for the diffusion of water vapor molecules at the interface; on the other hand, the fully exfoliated GO-ODA nanosheets were inclined to align with the surface of the as-prepared RC nanocomposite films during hot-pressure drying, creating a much more tortuous pathway for diffusion of water molecules. The new insights could be valuable for widening application of cellulose such as packaging.

Synergetic Toughening Effect of Carbon Nanotubes and ß-Nucleating Agents on the Polypropylene Random Copolymer/Styrene-Ethylene-Butylene- Styrene Block Copolymer Blends.

Polypropylene random co-polymer (PPR)/styrene-ethylene-butylene-styrene (SBS) block copolymer blends with high toughness and favorable tensile properties were successfully obtained by blending with traces of multi-wall carbon nanotubes (MWCNTs) and ß-nucleating agents (ß-NAs). ß-NAs can effectively induce the ductile ß-form crystal in the PPR matrix. Although the addition of MWCNTs was reported to be only benefit for the tensile strength of PPR and relatively disadvantageous for the toughness, the obviously synergistic toughening effect in PPR/SBS blends was found when MWCNTs and ß-NAs coexisted. The notched izod impact strength of PPR/30 wt % SBS blend with MWCNTs and ß-NAs increased from 11.3 to 58.9 kJ/m²; more than 5-fold increment compared with pure PPR. Meanwhile, the tensile strength retention of this PPR blend is still above 72.2%. The micro-morphology indicated that the MWCNTs can act as bridges between SBS particle and PPR matrix, effectively transferring the stress and absorbing impact energy among SBS particles.

Layer-Structured Design and Fabrication of Cyanate Ester Nanocomposites for Excellent Electromagnetic Shielding with Absorption-Dominated Characteristic.

In this work, we propose novel layer-structured polymer composites (PCs) for manipulating the electromagnetic (EM) wave transport, which holds unique electromagnetic interference (EMI) shielding features. The as-prepared PCs with a multilayered structure exhibits significant improvement in overall EMI shielding effectiveness (EMI SE) by adjusting the contents and distribution of electrical and magnetic loss fillers. The layer-structured PCs with low nanofiller content (5 wt % graphene nanosheets (GNSs) and 15 wt % Fe3O4) and a thickness of only 2 mm exhibited ultrahigh electrical conductivity and excellent EMI SE, reaching up to 2000 S/m and 45.7 dB in the X-band, respectively. The increased EMI SE of the layer-structured PCs was mainly based on the improved absorption rather than the reflection of electromagnetic waves, which was attributed to the "absorb-reflect-reabsorb" process for the incident electromagnetic waves. This work may provide a simple and effective approach to achieve new EMI shielding materials, especially for absorption-dominated EMI shielding.

Facile preparation of 3D regenerated cellulose/graphene oxide composite aerogel with high-efficiency adsorption towards methylene blue.

Composite aerogels consisting of graphene oxide (GO) and regenerated cellulose (RCE) were prepared via a solution mixing-regeneration and freeze-drying process. The prepared RCE/GO composites aerogel exhibited 3D network thin-walled pore structure with large specific surface area, also favorable compression recovery capability, outstanding dye elimination efficiency and reusability after the addition of GO. With addition of only 0.5 wt% GO, the methylene blue (MB) elimination efficiency of RCE/GO aerogel reached 99.0% and still remained at 90.5% after five-time reused under oscillation adsorption. In addition, our research indicates that the excellent MB adsorption of RCE/GO composite aerogel was driven by electrostatic interactions and followed a pseudo-second-order adsorption kinetic and monolayer Langmuir adsorption isotherm. This investigation provides the guidance for the development of green environmental adsorbents to remove organic dye from sewage water.

Efficient electromagnetic interference shielding of lightweight carbon nanotube/polyethylene composites via compression molding plus salt-leaching.

Carbon nanotube/high density polyethylene (CNT/HDPE) foam composites with high electrical conductivity and electromagnetic interference (EMI) shielding performance were developed by means of compression molding plus salt-leaching. The uniform porous structure and interconnected CNT networks throughout the cell backbones endowed the as-prepared foam composites with a significantly lower electrical percolation threshold (0.22 vol%) than that of the solid composites (0.84 vol%). Owing to the multiple reflections and scattering between the cell-matrix interfaces, the foam composites presented a superior specific EMI shielding effectiveness (EMI SE) of 104.3 dB cm3 g-1, 2.2 times higher than that of their solid counterpart. Besides this, the pore sizes of the CNT/HDPE foam composites could be easily tuned by controlling the particle size of the porogen. Also, the electrical conductivity and specific EMI SE increased with an increase in the cell diameter, which was attributed to the formation of a more perfect conductive network in the cell backbones. Our approach provides a novel idea for fabricating new lightweight EMI shielding materials, especially for aircraft and spacecraft applications.