Wastewater from leather tanning and processing in Palestine: Characterization and management aspects.

Leather manufacturing industry has major environmental impacts. Characterization of tannery's wastewater (WW) is a key step in the management of wastewater released from various processes. This study presents some physicochemical characteristics measured in wastewater. It compares the pollution loads released from both goat and cow hides processing. The main pollution characteristics of wastewater released from two local tanneries were determined experimentally, through analyzing real samples of industrial discharges. These include chemical oxygen demand (COD), total solids (TS), total dissolved solids (TDS), total suspended solids (TSS), pH, and the concentrations of chloride, ammonia (NH3) and chromium in both states, Cr (III) and Cr (VI). Characterization of such processes effluents assists in identifying waste generation rates and discharges, and then in recommending cleaner production options. The results shows that the amount of WW produced in the local Palestinian tanneries is much lower than tanneries worldwide, whereas it is more concentrated with pollutants. Liming process has the highest COD and the highest pH value, where tanning process releases WW highly concentrated with chromium. Real process measurements and mass balance calculations indicated that the chromium uptake efficiency is only 46.6%. Such a low efficiency indicates that cleaner production measures are essential in local tanneries.

The Phase Behavior of γ-Oryzanol and ß-Sitosterol in Edible Oil.

The phase behavior of binary mixtures of γ-oryzanol and ß-sitosterol and ternary mixtures of γ-oryzanol and ß-sitosterol in sunflower oil was studied. Binary mixtures of γ-oryzanol and ß-sitosterol show double-eutectic behavior. Complex phase behavior with two intermediate mixed solid phases was derived from differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS) data, in which a compound that consists of γ-oryzanol and ß-sitosterol molecules at a specific ratio can be formed. SAXS shows that the organization of γ-oryzanol and ß-sitosterol in the mixed phases is different from the structure of tubules in ternary systems. Ternary mixtures including sunflower oil do not show a sudden structural transition from the compound to a tubule, but a gradual transition occurs as γ-oryzanol and ß-sitosterol are diluted in edible oil. The same behavior is observed when melting binary mixtures of γ-oryzanol and ß-sitosterol at higher temperatures. This indicates the feasibility of having an organogelling agent in dynamic exchange between solid and liquid phase, which is an essential feature of triglyceride networks.

Is Desalination a Solution to Freshwater Scarcity in Developing Countries?

Rapid population growth and urbanization are two main drivers for the over-abstraction of conventional freshwater resources in various parts of the world, which leads to the situation of water scarcity (per capita availability <1000 m3/year). Predictions based on the World Bank projected population data and the FAO AQUASTAT database for freshwater availability show that by 2050, 2 billion people living in 44 countries will likely suffer from water scarcity, of which 95% may live in developing countries. Among these, the countries that will likely be most strongly hit by water scarcity by 2050 are Uganda, Burundi, Nigeria, Somalia, Malawi, Eritrea, Ethiopia, Haiti, Tanzania, Niger, Zimbabwe, Afghanistan, Sudan, and Pakistan. Currently, these countries have not yet established desalination to meet their freshwater demand. However, the current global trend shows that membrane-based desalination technology is finding new outlets for supplying water to meet growing water demand in most of the water-scarce countries. These 14 water-scarce countries will demand an additional desalination capacity of 54 Mm3/day by 2050 in order to meet the standard of current municipal water demand and to compensate for the withdrawal of renewable resources. Case studies from India, China, and South Africa have highlighted that other countries may apply the strategy of using desalinated water for industrial users. Moreover, challenges to the widespread adoption of desalination exist such as expense, significant energy use, the need for specialized staff training, the large carbon footprint of facilities, environmental issues such as greenhouse gas emission (GHGs), chemical discharge, and operational problems such as membrane fouling.

Removal of hydrogen sulfide from biogas using activated carbon synthesized from different locally available biomass wastes - a case study from Palestine.

The main aim of this study was to remove hydrogen sulfide (H2S) from biogas by adsorption using synthesized activated carbon prepared using locally available biomass. The effect of the type of precursors, impregnation reagent and bed height was studied in continuous reactors. Three types of biomass wastes (almond shells, eucalyptus and coffee grains) were collected, grinded, sieved, pyrolyzed at 500°C and impregnated with chemical reagents such as potassium hydroxide or zinc chloride. Adsorption tests were performed using a fixed bed filter filled with the produced activated carbon. The highest biochar yield of 36% was obtained eucalyptus followed by almond shells (28.5%) and coffee grains (24%), respectively. The highest adsorption capacity and removal efficiency were obtained with eucalyptus followed by almond shells and coffee grains, respectively. For instance, eucalyptus showed an adsorption capacity of ~690 (mg hydrogen sulfide/g adsorbent) followed by almond (230 mg hydrogen sulfide/g adsorbent) and coffee grains (22 mg hydrogen sulfide/g adsorbent). As an impregnation reagent, potassium hydroxide gave the highest adsorption efficiency and capacity than zinc chloride. Furthermore, the breakthrough time with KOH (180 min) was higher than ZnCl2 (70 min). Increasing the bed height during continuous breakthrough tests increased the adsorption capacity and hydrogen sulfide removal efficiency. The results of this study showed that the adsorption efficiency of the synthesized activated carbon and consequently the hydrogen sulfide removal efficiency could be fine-tuned by selecting an appropriate biomass precursor and proper impregnation reagent.

Stability of aqueous food grade fibrillar systems against pH change.

We report that the stability of an aqueous food grade fibril system upon pH change is affected by the presence of peptides that are formed during the process of fibril formation. We discuss several other relationships between food relevant properties and nano-scale characteristics, and compare these relationships for aqueous fibril systems to those of oil based fibril systems. In such fibril systems, dynamics, self-organisation, and sensitivity to external conditions, play an important role. These aspects are common to complex systems in general and define the future challenge in relating functional properties of food to molecular scale properties of their ingredients.

Organogel-emulsions with mixtures of ß-sitosterol and γ-oryzanol: influence of water activity and type of oil phase on gelling capability.

In this study, water-in-oil emulsions were prepared from water containing different salt concentrations dispersed in an oil phase containing a mixture of ß-sitosterol and γ-oryzanol. In pure oil, the ß-sitosterol and γ-oryzanol molecules self-assemble into tubular microstructures to produce a firm organogel. However, in the emulsion, the water molecules bind to the ß-sitosterol molecules, forming monohydrate crystals that hinder the formation of the tubules and resulting in a weaker emulsion-gel. Addition of salt to the water phase decreases the water activity, thereby suppressing the formation of sitosterol monohydrate crystals even after prolonged storage times (∼1 year). When the emulsions were prepared with less polar oils, the tubular microstructure was promoted, which significantly increased the firmness of the emulsion-gel. The main conclusion of this study is that the formation of oryzanol and sitosterol tubular microstructure in the emulsion can be promoted by reducing the water activity and/or by using oils of low polarity.

Elucidation of density profile of self-assembled sitosterol + oryzanol tubules with small-angle neutron scattering.

Small-angle neutron scattering (SANS) experiments have been performed on self-assembled tubules of sitosterol and oryzanol in triglyceride oils to investigate details of their structure. Alternative organic phases (deuterated and non-deuterated decane, limonene, castor oil and eugenol) were used to both vary the contrast with respect to the tubules and investigate the influence of solvent chemistry. The tubules were found to be composed of an inner and an outer shell containing the androsterol group of sitosterol or oryzanol and the ferulic acid moieties in the oryzanol molecule, respectively. While the inner shell has previously been detected in SAXS experiments, the outer shell was not discernible due to similar scattering length density with respect to the surrounding solvent for X-rays. By performing contrast variation SANS experiments, both for the solvent and structurant, a far more detailed description of the self-assembled system is obtainable. A model is introduced to fit the SANS data; we find that the dimensions of the inner shell agree quantitatively with the analysis performed in earlier SAXS data (radius of 39.4 +/- 5.6 angstroms for core and inner shell together, wall thickness of 15.1 +/- 5.5 angstroms). However, the newly revealed outer shell was found to be thinner than the inner shell (wall thickness 8.0 +/- 6.5 angstroms). The changes in the scattering patterns may be explained in terms of the contrast between the structurant and the organic phase and does not require any subtle indirect effects caused by the presence of water, other than water promoting the formation of sitosterol monohydrate in emulsions with aqueous phases with high water activity.

The Influence of Concentration and Temperature on the Formation of γ-Oryzanol + ß-Sitosterol Tubules in Edible Oil Organogels.

The gelation process of mixtures of γ-oryzanol and sitosterol structurants in sunflower oil was studied using light scattering, rheology, and micro-scanning calorimetry (Micro-DSC). The relation between temperature and the critical aggregation concentration (CAC) of tubule formation of γ-oryzanol and sitosterol was determined using these techniques. The temperature dependence of the CAC was used to estimate the binding energy and enthalpic and entropic contribution to the tubular formation process. The binding energy calculated at the corresponding temperatures and CACs were relatively low, in order of 2 RT (4.5 kJ mol(-1)), which is in accord with the reversibility of the tubular formation process. The formation of the tubules was associated with negative (exothermic) enthalpy change (ΔH(0)) compared with positive entropy term (-T ΔS(0) >0), indicating that the aggregation into tubules is an enthalpy-driven process. The oryzanol-sitosterol ratio affected the aggregation process; solutions with ratio of (60 oryzanol-40 sitosterol) started aggregation at higher temperature compared with other ratios.