Influence of design and postprocessing parameters on the degradation behavior and mechanical properties of additively manufactured magnesium scaffolds.

Magnesium shows promising properties concerning its use in absorbable implant applications such as biodegradability, improved mechanical strength and plastic deformability. Following extensive research, the first fixation and compression screws composed of magnesium rare earth alloys were commercialised, notably in the field of orthopaedic surgery. Preclinical and clinical follow-up studies showed that the rapid degradation of unprotected metallic Magnesium surfaces and concomitant hydrogen gas bursts still raise concern regarding certain surgical indications and need to be further improved. In order to enlarge the scope of further applications, the development of future magnesium implants must aim at freedom of design and reduction of volume, hereby enabling higher functionalised implants, as e.g. plate systems or scaffold grafts for bone replacement therapy. In order to overcome the boundaries of conventional manufacturing methods such as turning or milling, the process of Laser Powder Bed Fusion (LPBF) for magnesium alloys was recently introduced. It enables the production of lattice structures, therefore allowing for reduction of implant material volume. Nevertheless, the concomitant increase of free surface of such magnesium scaffolds further stresses the aforementioned disadvantages of vast degradation and early loss of mechanical stability if not prevented by suitable postprocessing methods. Magnesium scaffold structures with different pore sizes were therefore manufactured by LPBF and consequently further modified either by thermal heat treatment or Plasma Electrolytic Oxidation (PEO). Implant performance was assessed by conducting degradation studies and mechanical testing. PEO modified scaffolds with small pore sizes exhibited improved long-term stability, while heat treated specimens showed impaired performance regarding degradation and mechanical stability. STATEMENT OF SIGNIFICANCE: Magnesium based scaffold structures offer wide possibilities for advanced functionalized bioabsorbable implants. By implementing lattice structures, big implant sizes and mechanically optimized implant geometries can be achieved enabling full bone replacement or large-scale plate systems, e.g. for orthopedic applications. As shape optimization and lattice structuring of such scaffolds consequently lead to enlarged surface, suitable design and postprocessing routines come into focus. The presented study addresses these new and relevant topics for the first time by evaluating geometry as well as heat and surface treatment options as input parameters for improved chemical and mechanical stability. The outcome of these variations is measured by degradation tests and mechanical analysis. Evaluating these methods, a significant contribution to the development of absorbable magnesium scaffolds is made. The findings can help to better understand the interdependence of high surface to volume ratio Magnesium implants and to deliver methods to incorporate such lattice structures into future large-scale implant applications manufactured from bioabsorbable Magnesium alloys.

Laser additive manufacturing of biodegradable magnesium alloy WE43: A detailed microstructure analysis.

WE43, a magnesium alloy containing yttrium and neodymium as main alloying elements, has become a well-established bioresorbable implant material. Implants made of WE43 are often fabricated by powder extrusion and subsequent machining, but for more complex geometries laser powder bed fusion (LPBF) appears to be a promising alternative. However, the extremely high cooling rates and subsequent heat treatment after solidification of the melt pool involved in this process induce a drastic change in microstructure, which governs mechanical properties and degradation behaviour in a way that is still unclear. In this study we investigated the changes in the microstructure of WE43 induced by LPBF in comparison to that of cast WE43. We did this mainly by electron microscopy imaging, and chemical mapping based on energy-dispersive X-ray spectroscopy in conjunction with electron diffraction for the identification of the various phases. We identified different types of microstructure: an equiaxed grain zone in the center of the laser-induced melt pool, and a lamellar zone and a partially melted zone at its border. The lamellar zone presents dendritic lamellae lying on the Mg basal plane and separated by aligned Nd-rich nanometric intermetallic phases. They appear as globular particles made of Mg3Nd and as platelets made of Mg41Nd5 occurring on Mg prismatic planes. Yttrium is found in solid solution and in oxide particles stemming from the powder particles' shell. Due to the heat influence on the lamellar zone during subsequent laser passes, a strong texture developed in the bulk material after substantial grain growth. STATEMENT OF SIGNIFICANCE: Additively manufactured magnesium alloys have the potential of providing a major breakthrough in bone-reconstruction surgery by serving as biodegradable porous scaffold material. This study is the first to report in detail on the microstructure development of the established magnesium alloy WE43 fabricated by the additive manufacturing process of Laser Powder Bed Fusion (LPBF). It presents unique microstructural features which originate from the laser-melting process. An in situ transmission electron microscopy heating experiment further demonstrates the development of two distinct intermetallic phases in additively manufactured WE43 alloys. While one forms already during solidification, the other precipitates due to the ongoing heat treatment during LPBF processing.