The impact of film deposition and annealing on the nanostructure and dielectric constant of organic semiconductor thin films.

The strategy of using a bulk-heterojunction light-absorbing layer has led to the most efficient organic solar cells. However, optimising the blend morphology to maximise light absorption, charge generation and extraction can be challenging. Homojunction devices containing a single component have the potential to overcome the challenges associated with bulk heterojunction films. A strategy towards this goal is to increase the dielectric constant of the organic semiconductor to ≈10, which in principle would lead to free charge carrier generation upon photoexcitation. However, the factors that affect the thin film dielectric constants are still not well understood. In this work we report an organic semiconductor material that can be solution processed or vacuum evaporated to form good quality thin films to explore the effect of chromophore structure and film morphology on the dielectric constant and other optoelectronic properties. 2,2'-[(4,4,4',4'-Tetrakis{2-[2-methoxyethoxy]ethyl}-4H,4'H-{2,2'-bi[cyclo-penta[2,1-b:3,4-b']dithiophene]}-6,6'-diyl)bis(methaneylylidene)]dimalononitrile [D(CPDT-DCV)] was designed to have high electron-affinity end groups and low ionisation-potential central moieties. It can be processed from solution or be thermally evaporated, with the film morphology changing from face-on to a herringbone arrangement upon solvent or thermal annealing. The glycol solubilising groups led to the static dielectric constant (taken from capacitance measurements) of the films to be between 6 and 7 (independent of processing conditions), while the optical frequency dielectric constant depended on the processing conditions. The less ordered solution processed film was found to have the lowest optical frequency dielectric constant of 3.6 at 2.0 × 1014 Hz, which did not change upon annealing. In contrast, the more ordered evaporated film had an optical frequency dielectric constant 20% higher at 4.2 and thermal annealing further increased it to 4.5, which is amongst the highest reported for an organic semiconductor at that frequency. Finally, the more ordered evaporated films had more balanced charge transport, which did not change upon annealing.

Charge Generation Pathways in Organic Solar Cells: Assessing the Contribution from the Electron Acceptor.

Photocurrent generation in organic bulk heterojunction (BHJ) solar cells is most commonly understood as a process which predominantly involves photoexcitation of the lower ionization potential species (donor) followed by electron transfer to the higher electron affinity material (acceptor) [i.e., photoinduced electron transfer (PET), which we term Channel I]. A mirror process also occurs in which photocurrent is generated through photoexcitation of the acceptor followed by hole transfer to the nonexcited donor or photoinduced hole transfer (PHT), which we term Channel II. The role of Channel II photocurrent generation has often been neglected due to overlap of the individual absorption spectra of the donor and acceptor materials that are commonly used. More recently Channel II charge generation has been explored for several reasons. First, many of the new high-efficiency polymeric donors are used as the minority component in bulk heterojunction blends, and therefore, the acceptor absorption is a significant fraction of the total; second, nonfullerene acceptors have been prepared, which through careful design, allow for spectral separation from the donor material, facilitating fundamental studies on charge generation. In this article, we review the methodologies for investigating the two charge generation channels. We also discuss the factors that affect charge generation via Channel I and II pathways, including energy levels of the materials involved, exciton diffusion, and other considerations. Finally, we take a comprehensive look at the nonfullerene acceptor literature and discuss what information about Channel I and Channel II can be obtained from the experiments conducted and what other experiments could be undertaken to provide further information about the operational efficiencies of Channels I and II.

Detection of Explosive Vapors: The Roles of Exciton and Molecular Diffusion in Real-Time Sensing.

Time-resolved quartz crystal microbalance with in situ fluorescence measurements are used to monitor the sorption of the nitroaromatic (explosive) vapor, 2,4-dinitrotoluene (DNT) into a porous pentiptycene-containing poly(phenyleneethynylene) sensing film. Correlation of the nitroaromatic mass uptake with fluorescence quenching shows that the analyte diffusion follows the Case-II transport model, a film-swelling-limited process, in which a sharp diffusional front propagates at a constant velocity through the film. At a low vapor pressure of DNT of ≈16 ppb, the analyte concentration in the front is sufficiently high to give an average fluorophore-analyte separation of ≈1.5 nm. Hence, a long exciton diffusion length is not required for real-time sensing in the solid state. Rather the diffusion behavior of the analyte and the strength of the binding interaction between the analyte and the polymer play first-order roles in the fluorescence quenching process.

Photophysics of detection of explosive vapours via luminescence quenching of thin films: impact of inter-molecular interactions.

Fluorescence-based detection of explosive analytes requires an understanding of the nature of the excited state responsible for the luminescence response of a sensing material. Many measurements are carried out to elucidate the fundamental photophysical properties of an emissive material in solution. However, simple transfer of the understanding gained from the solution measurements to the solid-state can lead to errors. This is in part due to the absence of inter-molecular interactions of the chromophores in solution, which are present in the solid-state. To understand the role of inter-molecular interactions on the detection of explosive analytes we have chosen dendrimers from two different families, D1 and D2, which allow facile control of the inter-molecular interactions through the choice of dendrons and emissive chromophores. Using ultrafast transient absorption spectroscopy we find that the solution photoinduced absorption (PA) for both materials can be explained in terms of the generation of singlet excitons, which decay to the ground state, or intersystem cross (ISC) to form a triplet exciton. In neat films however, we observe different photophysical behaviours; first, ISC to the triplet state does not occur, and second, depending on the chromophore, charge transfer and charge separated states are formed. Furthermore, we find that when either dendrimer is interfaced with analyte vapour, the singlet state is strongly quenched, generating a charge transfer state that undergoes geminate recombination.

Tuning the optoelectronic properties of nonfullerene electron acceptors.

Broad spectral coverage over the solar spectrum is necessary for photovoltaic technologies and is a focus for organic solar cells. We report a series of small-molecule, nonfullerene electron acceptors containing the [(benzo[c][1,2,5]thiadiazol-4-yl)methylene]malononitrile unit as a high electron affinity component. The optoelectronic properties of these molecules were fine-tuned with the objective of attaining strong absorption at longer wavelengths by changing the low-ionization-potential moiety. The electron-accepting function of these materials was investigated with poly(3-n-hexylthiophene) (P3HT) as a standard electron donor. Significant photocurrent generation in the near infrared region, with an external quantum yield reaching as high as 22 % at 700 nm and an onset >800 nm was achieved. The results support efficient hole transfer to P3HT taking place after light absorption by the acceptor molecules. A Channel II-dominated power conversion efficiency of up to 1.5 % was, thus, achieved.

Spectral dependence of the internal quantum efficiency of organic solar cells: effect of charge generation pathways.

The conventional picture of photocurrent generation in organic solar cells involves photoexcitation of the electron donor, followed by electron transfer to the acceptor via an interfacial charge-transfer state (Channel I). It has been shown that the mirror-image process of acceptor photoexcitation leading to hole transfer to the donor is also an efficient means to generate photocurrent (Channel II). The donor and acceptor components may have overlapping or distinct absorption characteristics. Hence, different excitation wavelengths may preferentially activate one channel or the other, or indeed both. As such, the internal quantum efficiency (IQE) of the solar cell may likewise depend on the excitation wavelength. We show that several model high-efficiency organic solar cell blends, notably PCDTBT:PC70BM and PCPDTBT:PC60/70BM, exhibit flat IQEs across the visible spectrum, suggesting that charge generation is occurring either via a dominant single channel or via both channels but with comparable efficiencies. In contrast, blends of the narrow optical gap copolymer DPP-DTT with PC70BM show two distinct spectrally flat regions in their IQEs, consistent with the two channels operating at different efficiencies. The observed energy dependence of the IQE can be successfully modeled as two parallel photodiodes, each with its own energetics and exciton dynamics but both having the same extraction efficiency. Hence, an excitation-energy dependence of the IQE in this case can be explained as the interplay between two photocurrent-generating channels, without recourse to hot excitons or other exotic processes.

Time-resolved neutron reflectometry and photovoltaic device studies on sequentially deposited PCDTBT-fullerene layers.

We have used steady-state and time-resolved neutron reflectometry to study the diffusion of fullerene derivatives into the narrow optical gap polymer poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (PCDTBT) to explore the sequential processing of the donor and acceptor for the preparation of efficient organic solar cells. It was found that when [6,6]-phenyl-C61-butyric-acid-methyl-ester (60-PCBM) was deposited onto a thin film of PCDTBT from dichloromethane (DCM), a three-layer structure was formed that was stable below the glass-transition temperature of the polymer. When good solvents for the polymer were used in conjunction with DCM, both 60-PCBM and [6,6]-phenyl-C71-butyric-acid-methyl-ester (70-PCBM) were seen to form films that had a thick fullerene layer containing little polymer and a PCDTBT-rich layer near the interface with the substrate. Devices composed of films prepared by sequential deposition of the polymer and fullerene had efficiencies of up to 5.3%, with those based on 60-PCBM close to optimized bulk heterojunction (BHJ) cells processed in the conventional manner. Sequential deposition of pure components to form the active layer is attractive for large-area device fabrication, and the results demonstrate that this processing method can give efficient solar cells.

Energetic requirements of iridium(III) complex based photosensitisers in photocatalytic hydrogen generation.

A new family of Ir(III) complexes were synthesised and employed as light-induced hydrogen-production photosensitisers in aqueous systems, where hydrogen evolution was observed only when the PS* was reduced by the sacrificial agent, NEt3, signifying that a minimum potential difference of >0.2 V between E(PS*/PS(-)) and E(NEt3(+)/NEt3) is required for efficient hydrogen production [i.e., E(PS*/PS(-)) >1.19 V versus NHE]. The analytical method developed here is demonstrated to be useful for screening new photosensitisers for light-driven hydrogen generation.

Differentiating Between V- and G-Series Nerve Agent and Simulant Vapours Using Fluorescent Film Responses.

In-field rapid and reliable identification of nerve agents is critical for the protection of Defence and National Security personnel as well as communities. Fluorescence-based detectors can be portable and provide rapid detection of chemical threats. However, most current approaches cannot differentiate between dilute vapors of nerve agent classes and are susceptible to false positives due to the presence of common acids. Here a fluorescence-based method is shown for rapid differentiation between the V-series and phosphonofluoridate G-series nerve agents and avoids false positives due to common acids. Differentiation is achieved through harnessing two different mechanisms. Detection of the V-series is achieved using photoinduced hole transfer whereby the fluorescence of the sensing material is quenched in the presence of the V-series agent. The G-series is detected using a turn-on mechanism in which a silylated excited state intramolecular proton transfer sensing molecule is selectively deprotected by hydrogen fluoride, which is typically found as a contaminant and/or breakdown product in G-series agents such as sarin. The strategy provided discrimination between classes, as the sensor for the G-series agent class is insensitive to the V-series agent, and vice versa, and neither responded to common acids.

Dilute Donor Organic Solar Cells Based on Non-fullerene Acceptors.

The advent of small molecule non-fullerene acceptor (NFA) materials for organic photovoltaic (OPV) devices has led to a series of breakthroughs in performance and device lifetime. The most efficient OPV devices have a combination of electron donor and acceptor materials that constitute the light absorbing layer in a bulk heterojunction (BHJ) structure. For many BHJ-based devices reported to date, the weight ratio of donor to acceptor is near equal. However, the morphology of such films can be difficult to reproduce and manufacture at scale. There would be an advantage in developing a light harvesting layer for efficient OPV devices that contains only a small amount of either the donor or acceptor. In this work we explore low donor content OPV devices composed of the polymeric donor PM6 blended with high performance NFA materials, Y6 or ITIC-4F. We found that even when the donor:acceptor weight ratio was only 1:10, the OPV devices still have good photoconversion efficiencies of around 6% and 5% for Y6 and ITIC-4F, respectively. It was found that neither charge mobility nor recombination rates had a strong effect on the efficiency of the devices. Rather, the overall efficiency was strongly related to the film absorption coefficient and maintaining adequate interfacial surface area between donor and acceptor molecules/phases for efficient exciton dissociation.

The binding and fluorescence quenching efficiency of nitroaromatic (explosive) vapors in fluorescent carbazole dendrimer thin films.

We present a study on three generations of fluorescent carbazole dendrimers that exhibit strong binding with nitroaromatic compounds accompanied by photoluminescence (PL) quenching, making them attractive sensing materials for the detection of explosives such as 2,4,6-trinitrotoluene (TNT). The absorption and release of vapors of the (deuterated) TNT analogue 4-nitrotoluene (pNT) from thin films of the dendrimers were studied with a combination of time-correlated neutron reflectometry and PL spectroscopy. When saturated with pNT the PL of the films was fully quenched and could not be recovered with flowing nitrogen at room temperature but only upon heating to 40-80 °C. Although the majority of the absorbed pNT could be removed with this method the recovered films were found to still contain a residual pNT concentration of ~0.1 molecules per cubic nanometer. However, the proportion of the PL recovered increased with generation with the third generation dendrimer exhibiting close to full recovery despite the presence of residual pNT. This result is attributed to a combination of two effects. First, the dendrimer films present a range of binding sites for nitroaromatic molecules with the stronger binding sites surviving the thermal recovery process. Second, there is a large decrease of the exciton diffusion coefficient with dendrimer generation, preventing migration of the excitation to the remaining bound pNT.

Photophysics of delocalized excitons in carbazole dendrimers.

The photophysical properties in solution of three generations of carbazole-based dendrons and dendrimers with fluorenyl surface groups were studied using steady-state, time-resolved femtosecond transient absorption and anisotropy, and coherent two-dimensional ultraviolet spectroscopy. It was found that increasing the generation caused a switch in the nature of the emissive state between the first-generation compounds and the second- and third-generation dendrimers. Time-resolved anisotropy measurements revealed low initial anisotropies that decreased with increasing dendrimer generation consistent with increasing intradendrimer interchromophore coupling. Two-dimensional UV spectroscopy showed that the signal from the second- and third-generation dendrimers is the product of multiple chromophores interacting. The maximum number of interacting chromophores is reached by the second generation.

Utilizing Different Diffusion Mechanisms for Thin Film Fluorescence-Based Detection and Discrimination of Illicit Drug Vapors.

Film-based fluorescence sensors have been demonstrated to be powerful tools for real-time detection of trace chemical vapors. While explosive vapor detection via fluorescence quenching has been widely explored, fluorescence-based real-time detection and identification of illicit drug vapors remains a challenge. Here, we report two perylene diimide-based sensing materials, P1 and P2, incorporating 2,2-dihexyloctanyl chains and 4-[tris(4-{tert-butyl}phenyl)methyl]phenyl moieties at the imide positions, respectively. Quartz crystal microbalance with in situ photoluminescence measurements showed that N-methylphenethylamine, a simulant of methamphetamine (MA), diffused into films of P1 and P2 via Fickian and case-II mechanisms, respectively. The difference in the analyte diffusion mechanism led to P2 showing significantly faster luminescence quenching but slower luminescence recovery compared to P1. Finally, the different diffusion mechanisms were used as the basis for developing a simple sensor array based on P1 and P2 that could selectively detect free-base illicit drugs (MA, cocaine, and tetrahydrocannabinol) from potential interferants (organic amines, alcohol, and cosmetics) within 40 s.

Fluorinated Cation-Based 2D Perovskites for Efficient and Stable 3D/2D Heterojunction Perovskite Solar Cells.

Three-dimensional (3D) perovskite solar cells (PSCs) containing additives capable of forming two-dimensional (2D) structures in neat films have attracted attention due to their ability to enhance power conversion efficiency (PCE) in combination with improved operational stability. Herein, a newly designed fluorinated ammonium salt, 2-(perfluorophenyl)ethanaminium bromide:chloride50:50 (FEABr:Cl50:50), is introduced into CsMAFAPbI3-based PSCs with a standard n-i-p architecture. FEABr:Cl50:50 was used as an additive in the tin(IV) oxide (SnO2) electron transporting layer (ETL) as well as a surface treatment for the perovskite film. Used in this dual way, the additive was found to passivate charge-trapping defects within the SnO2 ETL and regulate the crystal growth of the perovskite layer. When FEABr:Cl50:50 was deposited onto the surface of the 3D perovskite film, it formed a thin hydrophobic 2D capping layer. Adopting this dual strategy led to the perovskite film having larger grain sizes, improved quality, and overall better device performance. As a result, the best-performing device exhibited a PCE of over 23% with negligible hysteresis in an n-i-p device architecture with an area of 0.2 cm2. Furthermore, unencapsulated devices with the hydrophobic 2D capping layer showed improved stability compared to the control device when measured under continuous light irradiation at a maximum power point (MPP) at 80 ± 5 °C in a humid (≈50%) environment.

Perylene Diimide Based Fluorescent Sensors for Drug Simulant Detection: The Effect of Alkyl-Chain Branching on Film Morphology, Exciton Diffusion, Vapor Diffusion, and Sensing Response.

Luminescence-based sensing has been demonstrated to be a powerful method for rapid trace detection of chemical vapors (analytes). Analyte diffusion has been shown to be the critical factor for real-time luminescence-based detection of explosive analytes via photoinduced electron transfer in amorphous films of conjugated polymers and dendrimers. However, similar studies to determine the critical factors for sensing have not been performed on materials that employ photoinduced hole transfer (PHT) to detect low electron affinity analytes such as illicit drugs. Nor have such studies been performed on semicrystalline sensing films. We have developed a family of perylene diimide-based sensing materials capable of undergoing PHT with amine-group containing analytes. It was found that the choice of branched alkyl chain [1-hexylheptyl (PHH), 2-hexyloctyl (PHO), or 2,2-dihexyloctyl (PDHO)] attached to the nitrogen atoms of the imide moiety strongly affected the solution-processed film morphology. PHH and PHO were found to contain crystalline phases, whereas PDHO was essentially amorphous. The degree of crystallinity strongly influenced exciton diffusion, with PHH and PHO exhibiting exciton diffusion coefficients that were 20× and 10× greater than the value of the amorphous PDHO. The degree of film crystallinity was also found to be critical when the films were applied to detect N-methylphenethylamine (MPEA), a simulant of methamphetamine. While PHH had the largest exciton diffusion coefficient [(1.0 ± 0.2) × 10-2 cm2 s-1] and analyte uptake (12.3 ± 1.8 ng) it showed the smallest quenching efficiency (2.6% ng-1). In contrast, PHO, which sorbed the least analyte (6.1 ± 0.4 ng) of the three compounds, had the largest quenching efficiency (7.1% ng-1) due to its molecular packing and hence exciton diffusion coefficient [(4.5 ± 1.4) × 10-3 cm2 s-1] not being affected by sorption of the analyte. These results show that when applying fluorescent films in practical detection scenarios there is a potential trade-off between a high exciton diffusion constant and analyte diffusion for semicrystalline sensing materials and that a high exciton diffusion coefficient in an as-cast film does not necessarily translate into a more efficient fluorescent quenching. The results also show that sensing materials that form semicrystalline films, whose packing is not disrupted by analyte diffusion, provide a route for overcoming these effects and achieving high sensitivity.

Twisted Carbazole Dendrons for Solution-Processable Green Emissive Phosphorescent Dendrimers.

A family of first-generation dendrimers containing 3,5-bis(carbazolyl)phenyl dendrons attached to a green emissive fac-tris(2-phenylpyridyl)iridium(III) core were prepared. The solubility of the dendrimers was imparted by the attachment of tert-butyl surface groups to the carbazole moieties. The dendrimers differed in the number of dendrons attached to each ligand (one or two dendrons) as well as the degree of rotational restriction within the dendrons. The densities of the films containing the doubly dendronized materials were higher than those of their mono-dendronized counterparts, with the dendrimer containing two rotationally constrained dendrons per ligand having the highest density at 1.12 ± 0.04 g cm-3. The dendrimers were found to have high photoluminescence quantum yields (PLQYs) in solution of between 80 and 90%, with the doubly dendronized materials having the lower values and a red-shifted emission. The neat film PLQY values of the dendrimers were less than those measured in solution although the relative decrease was smaller for the doubly dendronized materials. The dendrimers were incorporated into solution-processed bilayer organic light-emitting diodes (OLEDs) composed of neat or blend emissive layers and an electron transport layer. The best-performing devices had the dendrimers blended with a host material and external quantum efficiencies as high as 14.0%, which is higher than previously reported results for carbazole-incorporating emissive dendrimers. A feature of the devices containing blends of the doubly dendronized materials was that the maximum efficiency was relatively insensitive to the concentration in the host between 1 and 7 mol %.

Influence of the Alkyl Chain Length of (Pentafluorophenylalkyl) Ammonium Salts on Inverted Perovskite Solar Cell Performance.

We study the effect of (2,3,4,5,6-pentafluorophenyl)alkylamine additives with differing alkyl chain lengths (methyl, ethyl, and n-propyl) on the performance of methylammonium lead triiodide (MAPbI3) perovskite solar cells. The results show that the length of the alkyl chain between the 2,3,4,5,6-pentafluorophenyl group and ammonium moiety has a critical effect on the perovskite film structure and subsequent device performance. The 2,3,4,5,6-pentafluorophenyl ammonium additive with the shortest linking group (a methylene unit), namely (2,3,4,5,6-pentafluorophenyl)methylammonium iodide, was found to be distributed throughout the bulk of the perovskite film with a 2D phase only being observable at high concentrations (>30 mol%). In contrast, the additives with ethyl and n-propyl linking groups phase-separate during solution processing and are found to concentrate at the surface of the perovskite film. Photoluminescence measurements showed that the fluorinated additives passivated the surface defects on the perovskite grains. Of the three additives, inverted devices containing 0.32 mol% of the 2,3,4,5,6-pentafluorophenyl ammonium additive with the methylene linking group achieved a maximum power conversion efficiency of 22.0%, with the device efficiency decreasing with increasing additive concentration. In contrast, the devices composed of the additive with the longest alkyl linker, 3-(2,3,4,5,6-pentafluorophenyl)propylammonium iodide, had the poorest performance, with PCEs less than that of the neat MAPbI3 control and decreasing with increasing additive concentration.

Fluorinated Interlayer Modulation of NiOx-Based Inverted Perovskite Solar Cells.

p-Type inorganic nickel oxide (NiOx) exhibits high transparency, tunable-optoelectronic properties, and a work function (WF) that is potentially suitable for hole extraction in inverted perovskite solar cells (PSCs). However, NiOx films possess surface defects that lead to high interfacial recombination and an energy offset with the ionization potential of the perovskite. Herein, we show that fluorinated 3-(2,3,4,5,6-pentafluorophenyl)propan-1-aminium iodide (FPAI) can be used to modify the electronic properties of the NiOx anode interlayer. The FPAI modification led to good perovskite crystal growth and films with reduced surface defects. The FPAI modification also increased the WF of NiOx and improved charge extraction. These improvements led to an increased Voc value compared with control devices without FPAI modification, 1.05 V versus 1.00 V, and a higher short-circuit current and larger fill factor. As a result, the best PSCs with FPAI-modified NiOx had a power conversion efficiency of 19.3%. Finally, the PSCs with the FPAI-modified NiOx layer were found to have improved stability.

Acid is a potential interferent in fluorescent sensing of chemical warfare agent vapors.

A common feature of fluorescent sensing materials for detecting chemical warfare agents (CWAs) and simulants is the presence of nitrogen-based groups designed to nucleophilically displace a phosphorus atom substituent, with the reaction causing a measurable fluorescence change. However, such groups are also basic and so sensitive to acid. In this study we show it is critical to disentangle the response of a candidate sensing material to acid and CWA simulant. We report that pyridyl-containing sensing materials designed to react with a CWA gave a strong and rapid increase in fluorescence when exposed to Sarin, which is known to contain hydrofluoric acid. However, when tested against acid-free diethylchlorophosphate and di-iso-propylfluorophosphate, simulants typically used for evaluating novel G-series CWA sensors, there was no change in the fluorescence. In contrast, simulants that had been stored or tested under a standard laboratory conditions all led to strong changes in fluorescence, due to acid impurities. Thus the results provide strong evidence that care needs to be taken when interpreting the results of fluorescence-based solid-state sensing studies of G-series CWAs and their simulants. There are also implications for the application of these pyridyl-based fluorescence and other nucleophilic/basic sensing systems to real-world CWA detection.

Engineering fluorinated-cation containing inverted perovskite solar cells with an efficiency of >21% and improved stability towards humidity.

Efficient and stable perovskite solar cells with a simple active layer are desirable for manufacturing. Three-dimensional perovskite solar cells are most efficient but need to have improved environmental stability. Inclusion of larger ammonium salts has led to a trade-off between improved stability and efficiency, which is attributed to the perovskite films containing a two-dimensional component. Here, we show that addition of 0.3 mole percent of a fluorinated lead salt into the three-dimensional methylammonium lead iodide perovskite enables low temperature fabrication of simple inverted solar cells with a maximum power conversion efficiency of 21.1%. The perovskite layer has no detectable two-dimensional component at salt concentrations of up to 5 mole percent. The high concentration of fluorinated material found at the film-air interface provides greater hydrophobicity, increased size and orientation of the surface perovskite crystals, and unencapsulated devices with increased stability to high humidity.