Analytical Multimode Scanning and Transmission Electron Imaging and Tomography of Multiscale Structural Architectures of Sulfur Copolymer-Based Composite Cathodes for Next-Generation High-Energy Density Li-S Batteries.

Poly[sulfur-random-(1,3-diisopropenylbenzene)] copolymers synthesized via inverse vulcanization represent an emerging class of electrochemically active polymers recently used in cathodes for Li-S batteries, capable of realizing enhanced capacity retention (1,005 mAh/g at 100 cycles) and lifetimes of over 500 cycles. The composite cathodes are organized in complex hierarchical three-dimensional (3D) architectures, which contain several components and are challenging to understand and characterize using any single technique. Here, multimode analytical scanning and transmission electron microscopies and energy-dispersive X-ray/electron energy-loss spectroscopies coupled with multivariate statistical analysis and tomography were applied to explore origins of the cathode-enhanced capacity retention. The surface topography, morphology, bonding, and compositions of the cathodes created by combining sulfur copolymers with varying 1,3-diisopropenylbenzene content and conductive carbons have been investigated at multiple scales in relation to the electrochemical performance and physico-mechanical stability. We demonstrate that replacing the elemental sulfur with organosulfur copolymers improves the compositional homogeneity and compatibility between carbons and sulfur-containing domains down to sub-5 nm length scales resulting in (a) intimate wetting of nanocarbons by the copolymers at interfaces; (b) the creation of 3D percolation networks of conductive pathways involving graphitic-like outer shells of aggregated carbons;

A planar, chip-based, dual-beam refractometer using an integrated organic light-emitting diode (OLED) light source and organic photovoltaic (OPV) detectors.

We present a simple chip-based refractometer with a central organic light-emitting diode (OLED) light source and two opposed organic photovoltaic (OPV) detectors on an internal reflection element (IRE) substrate, creating a true dual-beam sensor platform. For first-generation platforms, we demonstrate the use of a single heterojunction OLED based on electroluminescence from an Alq(3)/TPD heterojunction (tris-(8-hydroxyquinoline)aluminum/N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine) and light detection with planar heterojunction pentacene/C(60) OPVs. The sensor utilizes the considerable fraction of emitted light from conventional thin-film OLEDs that is coupled into guided modes in the IRE, instead of into the forward (display) direction. A ray-optics description is used to describe light throughput and efficiency-limiting factors for light coupling from the OLED into the substrate modes, light traversing through the IRE substrate, and light coupling into the OPV detectors. The arrangement of the OLED at the center of the chip provides for two sensing regions: a "sample" channel and a "reference" channel, with detection of light by independent OPV detectors. This configuration allows for normalization of the sensor response against fluctuations in OLED light output, stability, and local fluctuations (temperature) that might influence sensor response. The dual-beam configuration permits significantly enhanced sensitivity to refractive index changes, relative to single-beam protocols, and is easily integrated into a field-portable instrumentation package. Changes in refractive index (DeltaRI) between 10(-2) and 10(-3) RI units could be detected for single beam operation, with sensitivity increased to DeltaRI approximately 10(-4) RI units when the dual-beam configuration is employed.

Conformal Polymeric Multilayer Coatings on Sulfur Cathodes via the Layer-by-Layer Deposition for High Capacity Retention in Li-S Batteries.

We report on the conformal coating of thickness-tunable multilayers directly onto the sulfur (S8) cathodes by the layer-by-layer (LbL) deposition for the significant improvement in the performances of Li-S batteries even without key additives (LiNO3) in the electrolyte. Poly(ethylene oxide) (PEO)/poly(acrylic acid) (PAA) multilayers on a single poly(allylamine hydrochloride) (PAH)/PAA priming bilayer, deposited on the S8 cathodes, effectively protected from the polysulfide leakage, while providing a Li+ ion diffusion channel. As a result, PAH/PAA/(PEO/PAA)3 multilayer-coated cathodes exhibited the highest capacity retention (806 mAh g-1) after 100 cycles at 0.5 C, as well as the high C-rate capability up to 2.0 C. Furthermore, the multilayer coating effectively mitigated the polysulfide shuttle effect in the absent of LiNO3 additives in the electrolyte.

Elemental Sulfur and Molybdenum Disulfide Composites for Li-S Batteries with Long Cycle Life and High-Rate Capability.

The practical implementation of Li-S technology has been hindered by short cycle life and poor rate capability owing to deleterious effects resulting from the varied solubilities of different Li polysulfide redox products. Here, we report the preparation and utilization of composites with a sulfur-rich matrix and molybdenum disulfide (MoS2) particulate inclusions as Li-S cathode materials with the capability to mitigate the dissolution of the Li polysulfide redox products via the MoS2 inclusions acting as "polysulfide anchors". In situ composite formation was completed via a facile, one-pot method with commercially available starting materials. The composites were afforded by first dispersing MoS2 directly in liquid elemental sulfur (S8) with sequential polymerization of the sulfur phase via thermal ring opening polymerization or copolymerization via inverse vulcanization. For the practical utility of this system to be highlighted, it was demonstrated that the composite formation methodology was amenable to larger scale processes with composites easily prepared in 100 g batches. Cathodes fabricated with the high sulfur content composites as the active material afforded Li-S cells that exhibited extended cycle lifetimes of up to 1000 cycles with low capacity decay (0.07% per cycle) and demonstrated exceptional rate capability with the delivery of reversible capacity up to 500 mAh/g at 5 C.

Molecular ordering in monolayers of an alkyl-substituted perylene-bisimide dye by attenuated total reflectance ultraviolet-visible spectroscopy.

Surface-relative orientational parameters were determined for monolayer films of N, N'-ditridecylperylenetetracarboxylic dianhydridediimide (C13-PTCDI) in terms of the relative electronic transition dipole strengths, providing a three-dimensional view of the absorption dipole distribution. In order to obtain a macroscopically ordered film, C13-PTCDI was deposited by (1) horizontal Lang-muir-Blodgett (LB) transfer onto methyl- and phenyl-silanized glass, and (2) vapor deposition onto oriented films of poly(tetrafluoroethylene) (PTFE) on glass. Films of LB-deposited C13-PTCDI were found to be completely isotropic prior to annealing. After annealing, these films remained isotropic in the plane of the substrate while the out-of-plane anisotropy was significantly enhanced. In contrast, films of C13-PTCDI vapor deposited onto oriented poly(tetrafluoroethylene) (PTFE)-modified substrates yielded films with a high degree of both in- and out-of-plane anisotropy. Atomic force microscopy (AFM) images of both the LB- and vapor-deposited films show substantial differences in film morphology and long-range order. These results demonstrate that molecular orientation in C13-PTCDI films can be controlled by varying substrate surface chemistry and post-deposition processing.

Improving the Charge Conductance of Elemental Sulfur via Tandem Inverse Vulcanization and Electropolymerization.

The synthesis of polymeric materials using elemental sulfur (S8) as the chemical feedstock has recently been developed using a process termed inverse vulcanization. The preparation of chemically stable sulfur copolymers was previously prepared by the inverse vulcanization of S8 and 1,3-diisopropenylbenzene (DIB); however, the development of synthetic methods to introduce new chemical functionality into this novel class of polymers remains an important challenge. In this report the introduction of polythiophene segments into poly(sulfur-random-1,3-diisopropenylbenzene) is achieved by the inverse vulcanization of S8 with a styrenic functional 3,4-propylenedioxythiophene (ProDOT-Sty) and DIB, followed by electropolymerization of ProDOT side chains. This methodology demonstrates for the first time a facile approach to introduce new functionality into sulfur and high sulfur content polymers, while specifically enhancing the charge conductivity of these intrinsically highly resistive materials.

Inverse Vulcanization of Elemental Sulfur to Prepare Polymeric Electrode Materials for Li-S Batteries.

Sulfur-rich copolymers based on poly(sulfur-random-1,3-diisopropenylbenzene) (poly(S-r-DIB)) were synthesized via inverse vulcanization to create cathode materials for lithium-sulfur battery applications. These materials exhibit enhanced capacity retention (1005 mAh/g at 100 cycles) and battery lifetimes over 500 cycles at a C/10 rate. These poly(S-r-DIB) copolymers represent a new class of polymeric electrode materials that exhibit one of the highest charge capacities reported, particularly after extended charge-discharge cycling in Li-S batteries.

New infrared transmitting material via inverse vulcanization of elemental sulfur to prepare high refractive index polymers.

Polymers for IR imaging: The preparation of high refractive index polymers (n = 1.75 to 1.86) via the inverse vulcanization of elemental sulfur is reported. High quality imaging in the near (1.5 µm) and mid-IR (3-5 µm) regions using high refractive index polymeric lenses from these sulfur materials was demonstrated.

The use of elemental sulfur as an alternative feedstock for polymeric materials.

An excess of elemental sulfur is generated annually from hydrodesulfurization in petroleum refining processes; however, it has a limited number of uses, of which one example is the production of sulfuric acid. Despite this excess, the development of synthetic and processing methods to convert elemental sulfur into useful chemical substances has not been investigated widely. Here we report a facile method (termed 'inverse vulcanization') to prepare chemically stable and processable polymeric materials through the direct copolymerization of elemental sulfur with vinylic monomers. This methodology enabled the modification of sulfur into processable copolymer forms with tunable thermomechanical properties, which leads to well-defined sulfur-rich micropatterned films created by imprint lithography. We also demonstrate that these copolymers exhibit comparable electrochemical properties to elemental sulfur and could serve as the active material in Li-S batteries, exhibiting high specific capacity (823 mA h g(-1) at 100 cycles) and enhanced capacity retention.

Directing the deposition of ferromagnetic cobalt onto Pt-tipped CdSe@CdS nanorods: synthetic and mechanistic insights.

A methodology providing access to dumbbell-tipped, metal-semiconductor and metal oxide-semiconductor heterostructured nanorods has been developed. The synthesis and characterization of CdSe@CdS nanorods incorporating ferromagnetic cobalt nanoinclusions at both nanorod termini (i.e., dumbbell morphology) are presented. The key step in the synthesis of these heterostructured nanorods was the decoration of CdSe@CdS nanorods with platinum nanoparticle tips, which promoted the deposition of metallic CoNPs onto Pt-tipped CdSe@CdS nanorods. Cobalt nanoparticle tips were then selectively oxidized to afford CdSe@CdS nanorods with cobalt oxide domains at both termini. In the case of longer cobalt-tipped nanorods, heterostructured nanorods were observed to self-organize into complex dipolar assemblies, which formed as a consequence of magnetic associations of terminal CoNP tips. Colloidal polymerization of these cobalt-tipped nanorods afforded fused nanorod assemblies from the oxidation of cobalt nanoparticle tips at the ends of nanorods via the nanoscale Kirkendall effect. Wurtzite CdS nanorods survived both the deposition of metallic CoNP tips and conversion into cobalt oxide phases, as confirmed by both XRD and HRTEM analysis. A series of CdSe@CdS nanorods of four different lengths ranging from 40 to 174 nm and comparable diameters (6-7 nm) were prepared and modified with both cobalt and cobalt oxide tips. The total synthesis of these heterostructured nanorods required five steps from commercially available reagents. Key synthetic considerations are discussed, with particular emphasis on reporting isolated yields of all intermediates and products from scale up of intermediate precursors.

Conducting polymer diffraction gratings on gold surfaces created by microcontact printing and electropolymerization at submicron length scales.

Conducting polymer diffraction gratings on Au substrates have been created using microcontact printing of C18-alkanethiols, followed by electropolymerization of either poly(aniline) (PANI) or poly(3,4-ethylenedioxythiophene) (PEDOT). Soft-polymer replicas of simple diffraction grating masters (1200 lines/mm) were used to define the alkanethiol template for polymer growth. Growth of PANI and PEDOT diffraction gratings was followed in real time, through in situ tapping-mode atomic force microscopy, and by monitoring diffraction efficiency (DE) as a function of grating depth. DE increased as grating depth increased, up to a limiting efficiency (13-26%, with white light illumination), defined by the combined optical properties of the grating and the Au substrate, and ultimately limited by the loss of resolution due to coalescence of the polymer films. Grating efficiency is strongly dependent upon the grating depth and the refractive index contrast between the grating material and the surrounding solutions. Both PEDOT and PANI gratings show refractive index changes as a function of applied potential, consistent with changes in refractive index brought about by the doping/dedoping of the conducting polymer. The DE of PANI gratings are strongly dependent on the pH of the superstrate solution; the maximum sensitivity (DeltaDE/DeltapH) is achieved with PANI gratings held at +0.4 V versus Ag/AgCl, where the redox chemistry is dominated by the acid-base equilibrium between the protonated (emeraldine salt) and deprotonated (emeraldine base) forms of PANI. Simulations of DE were conducted for various combinations of conducting polymer refractive index and grating depth, to compute sensitivity parameters, which are maximized when the grating depth is ca. 50% of its maximum obtainable depth.

Surface composition and electrical and electrochemical properties of freshly deposited and acid-etched indium tin oxide electrodes.

We compare the near-surface composition and electroactivity of commercial indium tin oxide (ITO) thin films, activated by plasma cleaning or etching with strong haloacids, with ITO films that have been freshly deposited in high vacuum, before and after exposure to the atmosphere or water vapor. Conductive-tip AFM, X-ray photoelectron spectroscopy (XPS), and the electrochemistry of probe molecules in solution were used to compare the relative degrees of electroactivity and the near-surface composition of these materials. Brief etching of commercial ITO samples with concentrated HCl or HI significantly enhances the electrical activity of these oxides as revealed by C-AFM. XPS was used to compare the composition of these activated surfaces, focusing on the intrinsically asymmetric O 1s line shape. Energy-loss processes associated with photoemission from the tin-doped, oxygen-deficient oxides complicate the interpretation of the O 1s spectra. O 1s spectra from the stoichiometric indium oxide lattice are accompanied by higher-binding-energy peaks associated with hydroxylated forms of the oxide (and in some cases carbonaceous impurities) and overlapping photoemission associated with energy-loss processes. Characterization of freshly sputter-deposited indium oxide (IO) and ITO films, transferred under high vacuum to the surface analysis environment, allowed us to differentiate the contributions of tin doping and oxygen-vacancy doping to the O 1s line shape, relative to higher-binding-energy O 1s components associated with hydroxyl species and carbonaceous impurities. Using these approaches, we determined that acid activation and O2 plasma etching create an ITO surface that is still covered with an average of one to two monolayers of hydroxide. Both of these activation treatments lead to significantly higher rates of electron transfer to solution probe molecules, such as dimethyferrocene in acetonitrile. Solution electron-transfer events appear to occur at no more than 4x10(7) electroactive sites per cm2 (each with diameters of ca. 50-200 nm) (i.e., a small fraction of the geometric area of the electrode). Electron-transfer rates correlate with the near-surface tin dopant concentration, suggesting that these electroactive sites arise from near-surface tin enrichment.