U.S. national PM2.5 Chemical Speciation Monitoring Networks-CSN and IMPROVE: description of networks.

The US. EnvironmentalProtection Agency (EPA) initiated the national PM2.5 Chemical Speciation Monitoring Network (CSN) in 2000 to support evaluation of long-term trends and to better quantify the impact of sources on particulate matter (PM) concentrations in the size range below 2.5 µm aerodynamic diameter (PM2.5; fine particles). The network peaked at more than 260 sites in 2005. In response to the 1999 Regional Haze Rule and the need to better understand the regional transport of PM, EPA also augmented the long-existing Interagency Monitoring of Protected Visual Environments (IMPROVE) visibility monitoring network in 2000, adding nearly 100 additional IMPROVE sites in rural Class 1 Areas across the country. Both networks measure the major chemical components of PM2.5 using historically accepted filter-based methods. Components measured by both networks include major anions, carbonaceous material, and a series of trace elements. CSN also measures ammonium and other cations directly, whereas IMPROVE estimates ammonium assuming complete neutralization of the measured sulfate and nitrate. IMPROVE also measures chloride and nitrite. In general, the field and laboratory approaches used in the two networks are similar; however, there are numerous, often subtle differences in sampling and chemical analysis methods, shipping, and quality control practices. These could potentially affect merging the two data sets when used to understand better the impact of sources on PM concentrations and the regional nature and long-range transport of PM2zs. This paper describes, for the first time in the peer-reviewed literature, these networks as they have existed since 2000, outlines differences infield and laboratory approaches, provides a summary of the analytical parameters that address data uncertainty, and summarizes major network changes since the inception of CSN. Implications: Two long-term chemical speciation particle monitoring networks have operated simultaneously in the United States since 2001, when the EPA began regular operations of its PM2.5 Chemical Speciation Monitoring Network (IMPROVE began in 1988). These networks use similar field sampling and analytical methods, but there are numerous, often subtle differences in equipment and methodologies that can affect the results. This paper describes these networks since 20000 (inception of CSN) and their differences, and summarizes the analytical parameters that address data uncertainty, providing researches and policymakers with background information they may need (e.g., for 2018 PM2.5 designation and State Implementation Plan process; McCarthy, 2013) to assess results from each network and decide how these data sets can be mutually employed for enhanced analyses. Changes in CSN and IMPROVE that have occurred over the years also are described.

The changing paradigm of air pollution monitoring.

The air pollution monitoring paradigm is rapidly changing due to recent advances in (1) the development of portable, lower-cost air pollution sensors reporting data in near-real time at a high-time resolution, (2) increased computational and visualization capabilities, and (3) wireless communication/infrastructure. It is possible that these advances can support traditional air quality monitoring by supplementing ambient air monitoring and enhancing compliance monitoring. Sensors are beginning to provide individuals and communities the tools needed to understand their environmental exposures with these data individual and community-based strategies can be developed to reduce pollution exposure as well as understand linkages to health indicators. Each of these areas as well as corresponding challenges (e.g., quality of data) and potential opportunities associated with development and implementation of air pollution sensors are discussed.

Characterization of summertime coarse particulate matter in the Desert Southwest--Arizona, USA.

UNLABELLED: A year-long study was conducted in Pinal County, AZ, to characterize coarse (2.5 - 10 microm aerodynamic diameter, AD) and fine (< 2.5 microm AD) particulate matter (PMc and PMf, respectively) to further understand spatial and temporal variations in ambient PM concentrations and composition in rural, arid environments. Measurements of PMc and PMf mass, ions, elements, and carbon concentrations at one-in-six day resolution were obtained at three sites within the region. Results from the summer of 2009 and specifically the local monsoon period are presented. The summer monsoon season (July - September) and associated rain and/or high wind events, has historically had the largest number of PM10 NAAQS exceedances within a year. Rain events served to clean the atmosphere, decreasing PMc concentrations resulting in a more uniform spatial gradient among the sites. The monsoon period also is characterized by high wind events, increasing PMc mass concentrations, possibly due to increased local wind-driven soil erosion or transport. Two PM10 NAAQS exceedances at the urban monitoring site were explained by high wind events and can likely be excluded from PM10 compliance calculations as exceptional events. At the more rural Cowtown site, PM10 NAAQS exceedances were more frequent, likely due to the impact from local dust sources. PM mass concentrations at the Cowtown site were typically higher than at the Pinal County Housing and Casa Grande sites. Crustal material was equal to 52-63% of the PMc mass concentration on average. High concentrations of phosphate and organic carbon found at the rural Cowtown were associated with local cattle feeding operations. A relatively high correlation between PMc and PMf (R2 = 0.63) indicated that the lower tail of the coarse particle fraction often impacts the fine particle fraction, increasing the PMf concentrations. Therefore, reductions in PMc sources will likely also reduce PMf concentrations, which also are near the value of the 24-hr PM2.5 NAAQS. IMPLICATIONS: In the desert southwest, summer monsoons are often associated with above average PM10 (< 10 microm AD) mass concentrations. Competing influences of monsoon rain and wind events showed that rain suppresses ambient concentrations while high wind increase them. In this region, the PMc fraction dominates PM10 and crustal sources contribute 52-63% to local PMc mass concentrations on average. Cattle feedlot emissions are also an important source and a unique chemical signature was identified for this source. Observations suggest monsoon wind events alone cannot explain PM10 NAAQS exceedances, thus requiring these values to remain in compliance calculations rather than being removed as exceptional wind events.

Mobile-Platform Measurement of Air Pollutant Concentrations in California: Performance Assessment, Statistical Methods for Evaluating Spatial Variations, and Spatial Representativeness.

Mobile platform measurements provide new opportunities for characterizing spatial variations of air pollution within urban areas, identifying emission sources, and enhancing knowledge of atmospheric processes. The Aclima, Inc. mobile measurement and data acquisition platform was used to equip four Google Street View cars with research-grade instruments, two of which were available for the duration of this study. On-road measurements of air quality were made during a series of sampling campaigns between May 2016 and September 2017 at high (i.e., 1-second [s]) temporal and spatial resolution at several California locations: Los Angeles, San Francisco, and the northern San Joaquin Valley (including non-urban roads and the cities of Tracy, Stockton, Manteca, Merced, Modesto, and Turlock). The results demonstrate that the approach is effective for quantifying spatial variations of air pollutant concentrations over measurement periods as short as two weeks. Measurement accuracy and precision are evaluated using results of weekly performance checks and periodic audits conducted through the sampler inlets, which show that research instruments located within stationary vehicles are capable of reliably measuring nitric oxide (NO), nitrogen dioxide (NO2), ozone (O3), methane (CH4) black carbon (BC), and particle number (PN) concentration with bias and precision ranging from <10 % for gases to <25 % for BC and PN at 1-s time resolution. The quality of the mobile measurements in the ambient environment is examined by comparisons with data from an adjacent (< 9 m) stationary regulatory air quality monitoring site and by paired collocated vehicle comparisons, both stationary and driving. The mobile measurements indicate that U.S. EPA classifications of two Los Angeles stationary regulatory monitors' scales of representation are appropriate. Paired time-synchronous mobile measurements are used to characterize the spatial scales of concentration variations when vehicles were separated by <1 to 10 kilometers (km). A data analysis approach is developed to characterize spatial variations while limiting the confounding influence of diurnal variability. The approach is illustrated using data from San Francisco, revealing 1-km scale differences in mean NO2 and O3 concentrations up to 117 % and 46 %, respectively, of mean values during a two-week sampling period. In San Francisco and Los Angeles, spatial variations up to factors of 6 to 8 occur at sampling scales of 100 - 300m, corresponding to 1-minute averages.

The national ambient air monitoring strategy: rethinking the role of national networks.

A current re-engineering of the United States routine ambient monitoring networks intended to improve the balance in addressing both regulatory and scientific objectives is addressed in this paper. Key attributes of these network modifications include the addition of collocated instruments to produce multiple pollutant characterizations across a range of representative urban and rural locations in a new network referred to as the National Core Monitoring Network (NCore). The NCore parameters include carbon monoxide (CO), sulfur dioxide (SO2), reactive nitrogen (NOy), ozone (O3), and ammonia (NH3) gases and the major fine particulate matter (PM2.5) aerosol components (ions, elemental and organic carbon fractions, and trace metals). The addition of trace gas instruments, deployed at existing chemical speciation sites and designed to capture concentrations well below levels of national air quality standards, is intended to support both long-term epidemiological studies and regional-scale air quality model evaluation. In addition to designing the multiple pollutant NCore network, steps were taken to assess the current networks on the basis of spatial coverage and redundancy criteria, and mechanisms were developed to facilitate incorporation of continuously operating particulate matter instruments.

Continuous and semicontinuous monitoring techniques for particulate matter mass and chemical components: a synthesis of findings from EPA's Particulate Matter Supersites Program and related studies.

The U.S. Environmental Protection Agency (EPA) established the Particulate Matter (PM) Supersites Program to provide key stakeholders (government and private sector) with significantly improved information needed to develop effective and efficient strategies for reducing PM on urban and regional scales. All Supersites projects developed and evaluated methods and instruments, and significant advances have been made and applied within these programs to yield new insights to our understanding of PM accumulation in air as well as improved source-receptor relationships. The tested methods include a variety of continuous and semicontinuous instruments typically with a time resolution of an hour or less. These methods often overcome many of the limitations associated with measuring atmospheric PM mass concentrations by daily filter-based methods (e.g., potential positive or negative sampling artifacts). Semicontinuous coarse and ultrafine mass measurement methods also were developed and evaluated. Other semicontinuous monitors tested measured the major components of PM such as nitrate, sulfate, ammonium, organic and elemental carbon, trace elements, and water content of the aerosol as well as methods for other physical properties of PM, such as number concentration, size distribution, and particle density. Particle mass spectrometers, although unlikely to be used in national routine monitoring networks in the foreseeable future because of their complex technical requirements and cost, are mentioned here because of the wealth of new information they provide on the size-resolved chemical composition of atmospheric particles on a near continuous basis. Particle mass spectrometers likely represent the greatest advancement in PM measurement technology during the last decade. The improvements in time resolution achieved by the reported semicontinuous methods have proven to be especially useful in characterizing ambient PM, and are becoming essential in allowing scientists to investigate sources of particulate pollution and to probe into the dynamics and mechanisms of aerosol formation in the atmosphere.

Secondary particulate matter in the United States: insights from the Particulate Matter Supersites Program and related studies.

Secondary aerosols comprise a major fraction of fine particulate matter (PM2.5) in all parts of the country, during all seasons, and times of day. The most abundant secondary species include sulfate, nitrate, ammonium, and secondary organic aerosols (SOAs). The relative abundance of each species varies in space and time as a function of meteorology, source emissions strength and type, thermodynamics, and atmospheric processing. Transport of secondary aerosols from upwind locations can contribute significantly at downwind receptor sites, especially regionally in the eastern United States, and across a given urbanized area, such as in Los Angeles. Processes governing the formation of the inorganic secondary species (sulfate, nitrate, and ammonium) are fairly well understood, although the occurrence of nucleation bursts initiated with the formation of ultrafine sulfuric acid particles observed regionally on clean days in the eastern United States was unexpected. Because of the complex nature of organic material in air, much is still to be learned about the sources, formation, and even spatial and temporal distributions of SOAs. For example, a considerable fraction of ambient organic PM is oxidized organic species, many of which still need to be identified, quantified, and their sources and formation mechanisms determined. Furthermore, significant uncertainty (approaching 50% or more) is associated with estimating the SOA fraction of organic material in air with current methods. This review summarizes the findings of the Supersites Program and related studies addressing secondary particulate matter (PM), including spatial and temporal variations of secondary PM and its precursor species, data and methods for determining the primary and secondary fractions of PM mass, and findings on the anthropogenic and natural fractions of secondary PM.

Key scientific findings and policy- and health-relevant insights from the U.S. Environmental Protection Agency's Particulate Matter Supersites Program and related studies: an integration and synthesis of results.

In 1998, the U.S. Environmental Protection Agency (EPA) initiated a major air quality program known as the Particulate Matter (PM) Supersites Program. The Supersites Program was a multiyear, $27 million air quality monitoring program consisting of eight regional air quality projects located throughout the United States, each with differing atmospheric pollution conditions resulting from variations in source emissions and meteorology. The overall goal of the program was to elucidate source-receptor relationships and atmospheric processes leading to PM accumulation on urban and regional scales; thus providing the scientific underpinning for modeling and data analysis efforts to support State Implementation Plans and more effective risk management approaches for PM. The program had three main objectives: (1) conduct methods development and evaluation, (2) characterize ambient PM, and (3) support health effects and exposure research. This paper provides a synthesis of key scientific findings from the Supersites Program and related studies. EPA developed 16 science/policy-relevant questions in conjunction with state and other federal agencies, Regional Planning Organizations, and the private sector. These questions were addressed to the extent possible, even given the vast amount of new information available from the Supersites Program, in a series of papers published as a special issue of the Journal of Air & Waste Management Association (February 2008). This synthesis also includes discussions of: (1) initial Supersites Program support for air quality management efforts in specific locations throughout the United States; (2) selected policy-relevant insights, based on atmospheric sciences findings, useful to air quality managers and decision makers planning emissions management strategies to address current and future PM National Ambient Air Quality Standards (NAAQS) and network planning and implementation; (3) selected health-relevant insights interpreted from atmospheric sciences findings in light of future directions for health and exposure scientists planning studies of the effects of PM on human health; and (4) selected knowledge gaps to guide future research. Finally, given the scope and depth of research and findings from the Supersites Program, this paper provides a reference source so readers can glean a general understanding of the overall research conducted and its policy-relevant insights. Supporting details for the results presented are available through the cited references. An annotated table of contents allows readers to easily find specific subject matter within the text.

Source Identification of Coarse Particles in the Desert Southwest, USA using Positive Matrix Factorization.

The Desert Southwest Coarse Particulate Matter Study was undertaken to further our understanding of the spatial and temporal variability and sources of fine and coarse particulate matter (PM) in rural, arid, desert environments. Sampling was conducted between February 2009 and February 2010 in Pinal County, AZ near the town of Casa Grande where PM concentrations routinely exceed the U.S. National Ambient Air Quality Standards (NAAQS) for both PM10 and PM2.5. In this desert region, exceedances of the PM10 NAAQS are dominated by high coarse particle concentrations, a common occurrence in this region of the United States. This work expands on previously published measurements of PM mass and chemistry by examining the sources of fine and coarse particles and the relative contribution of each to ambient PM mass concentrations using the positive matrix factorization receptor model (Clements et al., 2014). Coarse particles within the region were apportioned to nine sources including primary biological aerosol particles (PBAPs - 25%), crustal material (20%), re-entrained road dust (11%), feedlot (11% at the site closest to a cattle feedlot), secondary particles (10%), boron-rich crustal material (9%), and transported soil (6%), with minor contributions from ammonium nitrate, and salt (considered to be NaCl). Fine particles within the region were apportioned to six sources including motor vehicles (37%), road dust (29%), lead-rich (10%), with minor contributions from brake wear, crustal material, and salt. These results can help guide local air pollution improvement strategies designed to reduce levels of PM to below the NAAQS.

Regional Photochemical Measurement and Modeling Studies: A Summary of the Air & Waste Management Association International Specialty Conference.

This paper summarizes the Air & Waste Management Association's International Specialty Conference, "Regional Photochemical Measurement and Modeling Studies," held in San Diego, California, on November 8-12,1993. The purpose of the conference was to facilitate exchange of information and to initiate better communication and interaction among scientists, air quality managers, regulators, and others involved in or applying tools (models and measurements to support the modeling efforts) that can be used to develop equitable and effective emissions management practices for attainment of ozone standards. Attendees heard more than 350 presentations from authors representing nearly 30 air quality and meteorological measurement and modeling studies from 18 countries. While the primary emphasis of the conference was technical, two policy sessions were included (Plenary and Concluding Sessions) to place the technical results in perspective with the policy issues. The technical agenda was divided into three subjects: Analysis of Field Measurements (results and interpretation), Modeling (status and results), and Other Topics. Papers presented at the conference are being published in a variety of journals or books to meet the needs of the scientific and policy communities. A complete bibliographical listing of the papers presented at the conference is included with this paper. An unexpected outcome of the conference has been the development of an initiative for continuing the intercomparison of goals and scientific findings from regional air quality studies in Europe and North America, entitled "Regional Oxidants Programs Intercomparison" (ROxPIn). This paper will also discuss the goals and objectives of ROxPIn.

Objectives and Design of Central California's 1995 Integrated Monitoring Study of the California Regional PM10/PM2.5 Air Quality Study.

The 1995 Integrated Monitoring Study (IMS95) is part of the Phase 1 planning efforts for the California Regional PM10/PM2.5 Air Quality Study. Thus, the overall objectives of IMS95 are to (1) fill information gaps needed for planning an effective field program later this decade; (2) develop an improved conceptual model for pollution buildup (PM10, PM2.5, and aerosol precursors) in the San Joaquin Valley; (3) develop a uniform air quality, meteorological, and emissions database that can be used to perform initial evaluations of aerosol and fog air quality models; and (4) provide early products that can be used to help with the development of State Implementation Plans for PM10. Consideration of the new particulate matter standards were also included in the planning and design of IMS95, although they were proposed standards when IMS95 was in the planning process.