Sequential injection spectrophotometric determination of etilefrine hydrochloride.

A simple, fast, economical and automated sequential injection spectrophotometric method for the determination of etilefrine hydrochloride is developed. The method is based on the condensation reaction of etilefrine hydrochloride with 4-aminoantipyrine in the presence of alkaline potassium hexacyanoferrate and the absorbance of the colored product measured at 503 nm. Aspiration order, flow rate, reaction coil diameter, reaction coil length, concentration of 4-aminoantipyrine and potassium ferricyanide, as well as aspiration volume of reagents and sample has been optimized. Using these optimized parameters, a linear relationship between the relative peak height and concentration was obtained in the range 1-20 mg l(-1). The detection limit (as 3sigma value) was 0.1 mg l(-1) and precision was 2.7% and 1.5% at 1 and 2 mg l(-1), respectively. This method is superior over previously reported ones in terms of linear range, short analysis time, high sample throughput, excellent reagent economy and minimum waste generation.

New horizons in sequential injection kinetic analysis.

The need to measure several quantities rapidly in the same sample has prompted the development of automated methods of analysis that in both the continuous and discontinuous modes offer the possibility of simultaneous determinations. The application of pH gradients and differential kinetic determinations dominate the simultaneous determination of two or more closely related species in mixtures without prior separation. Various options enable use of kinetic-based measurements for the simultaneous determination of different analytes in flow systems. Some possible general reactions are given and discussed. The scope of sequential injection kinetic analysis is illustrated with examples.

On-line dilution and determination of the amount of concentrated hydrochloric acid in the final products from a hydrochloric acid production plant using a sequential injection titration system.

An on-line sequential injection titration system for the determination of the concentration of concentrated hydrochloric acid as final product from a hydrochloric acid production plant is described. The system involves on-line dilution of the concentrated hydrochloric acid solution to an acceptable range for direct measurement by merging the sample stream with a de-ionized water diluent stream, followed by mixing in a dilution coil, before aspiration into the sequential injection system. Concentrated standard solutions were treated in exactly the same way as the samples. The system was evaluated for reproducibility, linearity, accuracy, and sample throughput. A linear relationship between peak width and logarithm of acid concentration was found in the range 5.934-8.995 mol l(-1) and a concentration of 0.005 mol l(-1) NaOH solution was used as titrant. Samples from the production plant showed excellent agreement when compared with the manual and automated batchwise titrations. The relative standard deviation was found to be less than 0.4% with a sample frequency of 30 samples per hour.

Spectrophotometric determination of magnesium in pharmaceutical preparations by cost-effective sequential injection analysis.

A simple and rapid, inexpensive spectrophotometric method was proposed for magnesium assay in pharmaceutical preparations by sequential injection analysis (SIA). The method is based on the reaction between o-cresolphthalein complexone (CPC) and Mg(II) in alkaline media, yielding a pink colored complex with absorption maximum at 570nm. Since the formation constant between Ca-CPC and Mg-CPC is similar, initially a sample/standard solution was aspirated into the holding coil followed by a mixture of masking-buffer solutions. This was done because masking of calcium should be accomplished before Mg-CPC complexation. Then the reagent was introduced into the reaction coil to produce a colored complex, which is measured spectrophotometrically at 570nm. In this way the interference of calcium was reduced. Furthermore, all the parameters that affect the reaction were evaluated. The calibration curve is linear over a range of 0-20mgl(-1) of Mg(II) with a detection limit of 0.24mgl(-1). A sample throughput of 80 samples per hour and relative standard deviation <2.0% were achieved. The proposed method was successfully applied for the assay of magnesium in three different compositions of pharmaceutical preparations (tablets). The results were found to be in good agreement with the manual flame atomic absorption spectrophotometry (FAAS) and UV-Vis spectrophotometry methods and with the claimed values by the manufactures. The t-test shows no significant difference at 95% confidence level.

Sequential injection spectrophotometric determination of iron as Fe(II) in multi-vitamin preparations using 1,10-phenanthroline as complexing agent.

A sequential injection analysis (SIA) system is proposed for the determination of iron (II). Fe(II) was determined by SIA based on the reaction between 1,10-phenanthroline and iron (II), yielding an orange-red colour complex with absorption maximum at 512nm. The method involved aspiration of 187mul sample/standard zone followed by a zone of a reagent solution containing 140mul of 7.8 x 10(-4)moll(-1) 1,10-phenanthroline into a carrier stream to be stacked inside a holding coil and flow reversed through a reaction coil to a detector. The optimum condition was evaluated and the calibration curve is linear over a range of 0.25 to 5.0mgl(-1) of Fe(II) with detection limit of 18mugl(-1). A sample throughput of 40h(-1) was established. This technique is found to be simple, accurate, reproducible and sensitive. The proposed method was successfully applied for the determination of total iron as Fe(II) in pharmaceutical products (multi-vitamin tablets) and is especially useful for the determination of iron (II) in tablets with lower iron (II) contents. The results were found to be in good agreement with the results obtained by manual UV/Vis spectrophotometry and flame atomic absorption spectrometry (FAAS) and with claimed values by the manufacturers.

Sequential injection spectrophotometric determination of trace amounts of iodide by its catalytic effect on the 4,4'-methylenebis(N,N-dimethylaniline)-chloramine-T reaction.

A simple and sensitive sequential injection spectrophotometric procedure is proposed for the determination of trace amounts of iodide in pharmaceutical preparations. The method is based on the catalytic effect of iodide on the (tetra base) 4,4'-methylenebis(N,N-dimethylaniline)-chloramine-T reaction in acidic solution. The method involves a sequential aspiration of 255mul sample/standard followed by 170mul tetra base and then 128mul chloramine-T solutions into a carrier stream to be stacked inside a holding coil and flow reversed through a reaction coil towards a detector. The resulting colored compound is measured at 600nm using an UV/Vis-spectrophotometer. All the parameters that affect the reaction were evaluated and the calibration curve is linear over a range of 0.1-6.0mugl(-1) of iodide concentration with detection limit of 0.05mugl(-1). A sample throughput of 80 samples per hour and relative standard deviation of less than 2.0% was achieved. The method is successfully applied for the determination of iodide in three different samples (tablets).

An on-line potentiometric sequential injection titration process analyser for the determination of acetic acid.

An on-line potentiometric sequential injection titration process analyser for the determination of acetic acid is proposed. A solution of 0.1 mol L(-1) sodium chloride is used as carrier. Titration is achieved by aspirating acetic acid samples between two strong base-zone volumes into a holding coil and by channelling the stack of well-defined zones with flow reversal through a reaction coil to a potentiometric sensor where the peak widths were measured. A linear relationship between peak width and logarithm of the acid concentration was obtained in the range 1-9 g/100 mL. Vinegar samples were analysed without any sample pre-treatment. The method has a relative standard deviation of 0.4% with a sample frequency of 28 samples per hour. The results revealed good agreement between the proposed sequential injection and an automated batch titration method.