Island shape anisotropy in organic thin film growth induced by ion-beam irradiated rippled surfaces.

Controlling thin film growth of conjugated molecules is a key factor in organic electronics. Here, we report on the growth of the organic semiconductor para-hexaphenyl (6P) on ion bombarded, rippled TiO2(110) surfaces. These surfaces represent a one-dimensionally patterned substrate with alternating descending and ascending step trains with typical step distances below 1 nm. A clear island shape anisotropy and a discretization of the island width according to the ripple wavelength have been observed which are addressed to anisotropic detachment of molecules differently bound to the island rim at ascending and descending steps. By changing the average ripple length from ∼11 nm to ∼60 nm, the islands' length-to-width ratio could be tuned between ∼1.5 : 1 and ∼4.5 : 1. Further, strong diffusion anisotropy along and perpendicular to the ripples was found to be responsible for an increasing island density with decreasing ripple length.

Functionalization of Polypropylene by TiO2 Photocatalytic Nanoparticles: On the Importance of the Surface Oxygen Plasma Treatment.

A new two-step method for developing a nanocomposite of polypropylene (PP) decorated with photocatalytically active TiO2 nanoparticles (nTiO2) is proposed. This method involves the low-temperature plasma functionalization of polypropylene followed by the ultrasound-assisted anchoring of nTiO2. The nanoparticles, polymeric substrate, and resultant nanocomposite were thoroughly characterized using nanoparticle tracking analysis (NTA), microscopic observations (SEM, TEM, and EDX), spectroscopic investigations (XPS and FTIR), thermogravimetric analysis (TG/DTA), and water contact angle (WCA) measurements. The photocatalytic activity of the nanocomposites was evaluated through the degradation of methyl orange. The individual TiO2 nanoparticles ranged from 2 to 6 nm in size. The oxygen plasma treatment of PP generated surface functional groups (mainly -OH and -C=O), transforming the surface from hydrophobic to hydrophilic, which facilitated the efficient deposition of nTiO2. Optimized plasma treatment and sonochemical deposition parameters resulted in an active photocatalytic nTiO2/PP system, degrading 80% of the methyl orange under UVA irradiation in 200 min. The proposed approach is considered versatile for the functionalization of polymeric materials with photoactive nanoparticles and, in a broader perspective, can be utilized for the fabrication of self-cleaning surfaces.

Fabrication of plasmonic probes for reproducible nanospectroscopic investigation of lipid monolayers - The electrochemical etching with DC-pulsed voltage.

Tip-enhanced Raman spectroscopy (TERS) is a label-free analytical technique that characterizes molecular systems, potentially even with a nanometric resolution. In principle, the metallic plasmonic probe is illuminated with a laser beam generating the localized surface plasmons, which induce a strong local electric field enhancement in close proximity to the probe. Such field enhancement improves the Raman scattering cross-section from the sample volume localized near the probe apex. TERS provides a high spatial resolution and a great sensitivity, however, it is rather rarely used due to technical limitations causing unstable enhancement and the relative lack of data reproducibility. Despite many scientific efforts for the fabrication of effective TER probes providing robust TER enhancement still requires further investigations. In this work, we explore new possibilities based on preparation of scanning tunnelling microscopy (STM) plasmonic probes, since by nature of the tunnelling effect, they potentially could offer a very high spatial resolution in STM guided TERS experiments. Here we compare two methods of STM-TERS probe preparation for effective spectra acquisition. Our results strongly indicate that an application of square pulse voltage upon the etching procedure significantly improves the quality of the TER data over those obtained with a constant voltage one. To demonstrate the efficiency of our probes we present the results of hyperspectral TER mapping of the 1,2-dipalmitoyl-sn-glycero-3-phosphoethanolamine (DPPE) monolayer deposited on an ultra-pure and atomically flat gold substrate.

The influence of microinjection parameters on cell survival and procedure efficiency.

Microinjection is a method commonly used to deliver various substances into cells. The procedure is performed on a widefield microscope stage using fine glass needle to penetrate the cell membrane. Microinjection can be carried out using a manual or semi-automatic mode. For commercially available equipment currently reported microinjection success rate and cell viability are relatively low (around 50% for both indicators). Here, for the first time, we systematically show how the microinjection effectiveness and cell viability are influenced by needle diameter and chosen microinjection mode. We found that manual mode entailed a higher injection rate, reducing cell viability at the same time. The reduction in needle diameter caused a significant increase in cell survival rate (from 43 to 73% for manual mode and from 58% to 86% for semi-automatic mode) and did not affect significantly the success rate. Our findings will help optimize this method in the context of cell biology research.•This study shows how to improve microinjection parameters, such as procedure efficiency and cell survival rate, for commercially available equipment.•Manual mode, in comparison with semi-automatic mode, results in higher microinjection efficiency, but lower cell survival rate.•The increase in micropipette diameter causes lower cell viability and a higher microinjection success rate.

Optimization of tip-enhanced Raman spectroscopy for probing the chemical structure of DNA.

Tip-enhanced Raman (TER) spectroscopy combines the nanometric spatial resolution of atomic force microscopy (AFM) and the chemical sensitivity of Raman spectroscopy. Thus, it provides a unique possibility to obtain spectroscopic information on individual, nanometre-size molecules. The enhancement of Raman scattering cross-section requires modification of the AFM tip apex with a plasmonic nanostructure. Despite numerous advances of TERS research, attaining good reproducibility and stable enhancement is still challenging mainly due to the lack of optimized probes and sample preparation procedures. Moreover, current nanospectroscopic standard samples - carbon nanotubes (CNTs) have relatively simple chemical structure, and therefore, they are far from real-life analytes, especially biological samples. In this work we focus on the optimization of TERS technique for efficient DNA measurements, including: a preparation of atomically-flat gold substrates, fixative free deposition of DNA and optimization of TERS probe preparation. Here we demonstrate a comprehensive comparison of the efficacy of several types of TERS probes. Applying the systematic approach, we obtained reliable and reproducible TER spectra of DNA. Thus, we provide preparation procedures of a new standard TERS sample, TERS substrates and TERS probes. Our research provides a solid foundation for further research on DNA and its interaction with other biomolecules upon biologically significant processes such as DNA damage and repair.