From Collection or Archaeological Finds? A Non-Destructive Analytical Approach to Distinguish between Two Sets of Bronze Coins of the Roman Empire.

This study stems from the need for numismatics to establish whether there may be relationships between a group of 103 bronze coins from the Roman era found in archaeological excavations on the Cesén Mountain (Treviso, Italy) and a group of 117 coins kept at the Museum of Natural History and Archaeology in Montebelluna (Treviso, Italy). The chemists were delivered six coins with neither pre-agreements nor further information on the origin of the coins. Therefore, the request was to hypothetically assign the coins to the two groups on the basis of similarities and differences in their surface composition. Only non-destructive analytical techniques were allowed to be used to characterize the surface of the six coins taken blindly from the two sets. The elemental analysis of each coins' surface was carried out by µ-XRF. To better observe the morphology of the coins' surfaces, SEM-EDS was used. Compounds covering the coins coming from both corrosion processes (patinas) and the deposition of soil encrustations were also analyzed by means of the FTIR-ATR technique. The molecular analysis confirmed the presence of silico-aluminate minerals on some coins, unequivocally indicating a provenance from clayey soil. Some soil samples, collected from the archaeological site of interest, were analyzed to verify whether the encrusted layer on coins could contain chemical components compatible with them. This result, together with the chemical and morphological investigations, led us to subdivide the six target coins into two groups. The first group is made up of two coins coming from the set of coins from excavation (found in the subsoil) and from the set from open air finds (coins found in the top layer of the soil). The second group is made up of four coins that are devoid of characteristics corresponding to exposure to soil contact for long periods of time and, moreover, their surface compounds could suggest a different provenance. The analytical results of this study made it possible to correctly assign all six coins to the two groups of finds and support numismatics, which was unconvinced in considering all coins to come from the same finding site only on the basis of archaeological documentations.

The effect of carbodiimide on push-out bond strength of fiber posts and endogenous enzymatic activity.

BACKGROUND: To investigate the effect of 0.3 M 1-ethyl-3(3-dimethylaminopropyl) carbodiimide (EDC) aqueous solution pretreatment on push-out bond strength (PBS) and matrix-metalloproteinases (MMPs) activity within radicular dentin when different post cementation strategies were employed. METHODS: One hundred and twenty monoradicular human teeth were endodontically treated and randomly divided into six groups, depending on the cementation strategy and root dentin pretreatment (n = 20): EAR: cementation with an etch-and-rinse adhesive (LuxaBond Total Etch, DMG) and resin cement (LuxaCore Z Dual, DMG); EAR/EDC: 1 min EDC pretreatment after etching + EAR; SE: cementation with a self-etch primer (Multilink Primer, Ivoclar Vivadent) and corresponding cement (Multilink Automix, Ivoclar Vivadent); SE/EDC: self-etch primer + EDC pretreatment + SE; SA: cementation with a universal self-adhesive cement (RelyX Universal, 3 M); SA/EDC: EDC pretreatment + SA. Slices were submitted to PBS test and interfacial nanoleakage evaluation 24 h after cementation or after thermocycling (40.000 cycles, 5-55 °C). To investigate the effect of EDC on MMPs activity, 4 additional first maxillary premolars per group were processed for in situ zymography analysis. Multivariate ANOVA and post hoc Tukey tests were used to analyze PBS values. The data from in situ zymography were analyzed with Kruskal-Wallis test and Dunn's pairwise multiple comparison procedures (α = 0.05). RESULTS: The variables "EDC pretreatment", "root region" and "thermocycling" significantly influenced PBS (p < 0.05), while the variable "cementation strategy" had no influence (p > 0.05). Thermocycling significantly reduced PBS in SE and SA groups (p < 0.05). EDC was effective in preserving PBS after artificial aging. EDC pretreatment significantly reduced enzymatic activity at baseline in EAR and SE groups, and in SA group after thermocycling (p < 0.05). CONCLUSIONS: The use of EDC prevents the reduction of bond-strength values after artificial aging and silences endogenous enzymatic activity within radicular dentin when different cementation strategies were employed.

Profile of a new extended range-of-vision IOL: a laboratory study.

PURPOSE: To evaluate the surface profile of a new-generation extended range-of-vision intraocular lens (IOL) and to compare it with that obtained for a monofocal IOL based on the same platform. METHODS: Prospective, experimental, laboratory study comparing the surface profile of the DFT015 (AcrySof IQ Vivity; Alcon Laboratories, Inc.), a new-generation presbyopia-correcting IOL, with the profile of the SN60WF (AcrySof IQ; Alcon Laboratories, Inc.), an aspheric monofocal IOL based on the same platform. Raw profiles were obtained using contact profilometry. The best-fit form was then subtracted from each raw profile to highlight potential differences. RESULTS: No significant differences were appreciated in raw profiles. On the contrary, after form removal, the new extended range-of-vision IOL showed a peculiar profile characterized by the presence of two altitudinal symmetrical changes in the order of 1 µm, localized in the central portion of the optic. CONCLUSIONS: The new-generation extended range-of-vision IOL evaluated showed a smooth change of its surface compared to the same platform monofocal IOL. The altitudinal changes blended in the central design of the new presbyopia-correcting IOL, although micrometric, might play a crucial role in creating a continuous focal range while minimizing visual disturbances.

Scanning electron microscopy study of different one-piece foldable acrylic intraocular lenses after injection through microincisional cataract surgery cartridges.

PURPOSE: To evaluate possible surface alterations of different models of one-piece foldable acrylic intraocular lenses (IOLs) after folding and ejecting process through 2.2-mm microincisional cataract surgery (MICS) cartridges. METHODS: In this experimental laboratory study, the following IOLs were studied: Johnson&Johnson PCB00, HOYA iSert 251, Alcon AcrySof IQ SN60WF, Bausch&Lomb enVISTA MX-60. A total of 80 IOLs were analyzed. Twenty intraocular lenses of each type were studied: ten with a power of + 21 D ± 1 and ten with a power of + 28 D ± 1. IOLs were injected through a dedicated 2.2-mm MICS cartridge into a 50-mL vial containing 10 mL of deionized water. After rinsing and metallization process, scanning electron microscopy images were acquired. RESULTS: All IOLs presented high-quality construction biomaterials. Some IOLs showed superficial scratches and tears on the optic surface, mainly positioned according to the direction of the stress induced by the folding process. In other cases, small superficial tears were seen in a more peripheral position. CONCLUSIONS: All lenses showed excellent surface quality. After folding and injection process some superficial scratches and tears of the IOL optic were detected in some models. Further studies are needed to assess the possible effects of those superficial damages on the optical quality of the IOLs.

Cerium Oxide Nanoparticles Absorption through Intact and Damaged Human Skin.

Cerium oxide (CeO2) nanoparticles (NPs) are used in polishing products and absorbents, as promoters in wound healing, and as organopesticide decontaminants. While systemic bioaccumulation and organ toxicity has been described after inhalation, data on CeO2 NPs' transdermal permeation are lacking. Our study was an in vitro investigation of the permeation of 17-nm CeO2 NPs dispersed in synthetic sweat (1 g L-1) using excised human skin on Franz cells. Experiments were performed using intact and needle-abraded skin, separately. The average amount of Ce into intact and damaged skin samples was 3.64 ± 0.15 and 7.07 ± 0.78 µg cm-2, respectively (mean ± SD, p = 0.04). Ce concentration in the receiving solution was 2.0 ± 0.4 and 3.3 ± 0.7 ng cm-2 after 24 h (p = 0.008). The Ce content was higher in dermal layers of damaged skin compared to intact skin (2.93 ± 0.71 µg cm-2 and 0.39 ± 0.16 µg cm-2, respectively; p = 0.004). Our data showed a very low dermal absorption and transdermal permeation of cerium, providing a first indication of Ce skin uptake due to contact with CeO2.

Complex Coacervates between a Lactose-Modified Chitosan and Hyaluronic Acid as Radical-Scavenging Drug Carriers.

Complex coacervation of two oppositely charged polysaccharides, namely a lactose-modified chitosan (CTL) and hyaluronan (HA), was investigated in this study. Coacervates of the two polysaccharides were prepared by drop-by-drop injection of HA into CTL. Transmittance and dynamic light scattering (DLS) measurements in combination with TEM analyses demonstrated the formation of spheroidal colloids in the nano-/microsize range showing good homogeneity. Strikingly, the presence of 150 mM supporting NaCl did not hamper the colloid formation. Stability studies on selected formulations demonstrated that HA/CTL coacervates were stable up to 3 weeks at 37 °C and behaved as pH-responsive colloids since transition from entangled to disentangled chains was attained for a proper pH range. The possibility of freeze-drying the coacervates for storage purposes and the ability of encapsulating selected payloads were investigated as well, for two values of the fraction of the lactitol side-chain substitution (FL). Finally, biological tests using human neutrophils were undertaken at acidic pH value (pH = 6.0): under such experimental conditions, akin to those frequently occurring in the inflammatory microenvironment, coacervates scavenged reactive oxygen species (ROS) generated by these cells in basal conditions. Given the well documented bioactivity of CTL with respect to chitosan toward cartilage regeneration, these findings point to a possible application of HA/CTL-based colloids as scavenging and bioactive carriers for the delivery of therapeutic molecules at confined inflamed sites such as knee joints.

Influence of dentin pretreatment with synthetic hydroxyapatite application on the bond strength of fiber posts luted with 10-methacryloyloxydecyl dihydrogen phosphate-containing luting systems.

The aim of this in vitro study was evaluate the effect of application of synthetic hydroxyapatite on fiber post bond strength to radicular dentine. Forty, single-root teeth were endodontically treated and an 8 mm post space was prepared. Specimens were randomly placed in four groups (n = 10 in each) and treated using the following fiber post luting procedures: group 1, 17% EDTA + Panavia SA; group 2, 17% EDTA + Teethmate Desensitizer + Panavia SA; group 3, All-Bond Universal + Duo-Link Universal; and group 4, All-Bond Universal + Teethmate Desensitizer + Duo-Link Universal. Fiber posts were luted in the post space and light-cured for 120 s using a light-emitting diode (LED) lamp. After 7 d of storage at 37°C, the teeth were cut into 1-mm-thick slices, which were subjected to a push-out test until failure using a universal testing machine. Two specimens per group were prepared for scanning electron microscopy analysis. An energy-dispersive X-ray spectroscopy detector was used for elemental analysis of the specimen surface. The results were statistically analyzed using one-way anova. The fiber post bond strength was statistically significantly increased after the application of Teethmate Desensitizer to post space walls, either with a 10-MDP-containing self-adhesive cement or with a universal adhesive. Scanning electron microscopy and EDAX analysis showed that Teethmate Desensitizer created a calcium phosphate precipitate over post space dentinal tubules, which significantly improved the bond strength of the fiber post luted with 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP)-containing adhesive systems.

Evaluation of the In Vitro Effects of Cervical Marginal Relocation Using Composite Resins on the Marginal Quality of CAD/CAM Crowns.

PURPOSE: To evaluate the effect of cervical margin relocation (CMR) for crowns designed using CAD/CAM technology, and made of pre-cured resin or lithium disilicate, before and after thermomechanical loading. The test hypothesis was that the marginal quality of the crowns would not be influenced by the CMR with composite resins before or after thermomechanical loading. MATERIALS AND METHODS: Standard crown preparations were created in 40 human molars. The margins were located in enamel, except for the mesial proximal box, where the cervical margin was 2.0 mm below the cementoenamel junction, with 4.0 mm in the buccolingual and 2.0 mm in the mesiodistal dimension. For the CMR technique, a 2-mm layer of conventional or flowable composite resin was applied to the mesial box. Using the Cerec CAD/CAM system, 40 standard crowns were prepared, and restorations were luted using a dual-curing adhesive cement. SEM analysis was performed using epoxy resin replicas before and after loading to assess the marginal quality of interfaces of the mesial proximal box with CMR/crown and the distal face of the tooth without CMR. Statistical differences between groups were analyzed using the Kruskal-Wallis test and Bonferroni's post-hoc test. RESULTS: The null hypothesis was accepted, since no statistically significant differences were found in marginal quality before and after thermomechanical cycling (p > 0.05). CONCLUSION: The implementation of CMR before and after thermomechanical cycling had no effect on the quality of cervical margins. To establish whether CMR is a suitable procedure for the adhesive luting of composite resin crowns in deep proximal boxes, additional studies are required.

Use of methacrylate-modified chitosan to increase the durability of dentine bonding systems.

This study aimed at investigating the effect of a methacrylate-modified chitosan on the durability of adhesive interfaces to improve the clinical performance of dental restorations. Chitosan was modified with methacrylic acid (Chit-MA70) on 16% of the amino groups. Viscosity, rheology, and (1)H NMR spectroscopy were performed to characterize the modified polysaccharide. Chit-MA70 was blended into a primer of an "etch-and-rinse" experimental adhesive system and tested on human teeth. The presence of methacrylate moieties and of residual positive charges on the polysaccharide chain allowed Chit-MA70 to covalently bind to the restorative material and electrostatically interact with demineralized dentin. The Chit-MA70 containing an adhesive system showed values of the immediate bond strength (26.0 ± 8.7 MPa) comparable to the control adhesive system (25.5 ± 8.7 MPa). However, it was shown that upon performing thermo-mechanical cycling treatment of the dental restoration on human teeth, the adhesive with the methacrylate-modified chitosan, in variance with the control adhesive, did not show any decrease in the bond strength (28.4 ± 8.8 MPa). The modified chitosan is proposed as a component of the "etch-and-rinse" adhesive system to efficiently improve the durability of dental restorations.

Microradiography and microcomputed tomography comparative analysis in human bone cores harvested after maxillary sinus augmentation: a pilot study.

OBJECTIVES: The aim of this study was to compare microradiography (MR) and microcomputed tomography (µCT) analysis of bone samples following maxillary sinus augmentation at different time periods and determine the relationships between measured area and volume fractions. MATERIALS AND METHODS: Lateral window sinus grafts were performed on 10 patients using a mineralized human bone allograft (MHBA). At implant placement, 5-13 months after surgery, 10 bone core biopsies were harvested. Prior to histologic sectioning, bone samples were evaluated with µCT. The morphometric parameters computed by MR and µCT were compared using Pearson's correlation and Bland and Altman analysis and included hard tissue fraction (HV/TV:%), soft tissue fraction (SV/TV:%), vital bone fraction (BV/TV:%) and residual graft fraction (GV/TV:%). RESULTS: Strong positive correlation between MR and µCT was found for HV/TV and SV/TV and BV/TV [r = 0.84, 0.84 and 0.69, respectively] but weak for GV/TV [r = 0.10]. CONCLUSION: µCT technology shows promising potential as an indicator of bone morphology changes; however, caution should be used in interpreting morphometric parameters, as the different methods reveal important biases.

Alginate-Sr/Mg Containing Bioactive Glass Scaffolds: The Characterization of a New 3D Composite for Bone Tissue Engineering.

In bone regeneration, combining natural polymer-based scaffolds with Bioactive Glasses (BGs) is an attractive strategy to improve the mechanical properties of the structure, as well as its bioactivity and regenerative potential. Methods: For this purpose, a well-studied alginate/hydroxyapatite (Alg/HAp) porous scaffold was enhanced with an experimental bioglass (BGMS10), characterized by a high crystallization temperature and containing therapeutic ions such as strontium and magnesium. This resulted in an improved biological response compared to 45S5 Bioglass®, the "gold" standard among BGs. Porous composite scaffolds were fabricated by freeze-drying technique and characterized by scanning electron microscopy and microanalysis, infrared spectroscopy, and microcomputed tomography. The mechanical properties and cytocompatibility of the new scaffold composition were also evaluated. The addition of bioglass to the Alg/HAp network resulted in a slightly lower porosity. However, despite the change in pore size, the MG-63 cells were able to better adhere and proliferate when cultured for one week on a BG scaffold compared to the control Alg/HAp scaffolds. Thus, our findings indicate that the combination of bioactive glass BGMS10 does not affect the structural and physicochemical properties of the Alg/HAp scaffold and confers bioactive properties to the structures, making the Alg/HAp-BGMS10 scaffold a promising candidate for future application in bone tissue regeneration.

Primary Stability of Implants Inserted into Polyurethane Blocks: Micro-CT and Analysis In Vitro.

The approach employed for the site preparation of the dental implant is a variable factor that affects the implant's primary stability and its ability to integrate with the surrounding bone. The main objective of this in vitro study is to evaluate the influence of different techniques used to prepare the implant site on the primary stability of the implant in two different densities of artificial bone. MATERIALS AND METHODS: A total of 150 implant sites were prepared in rigid polyurethane blocks to simulate two distinct bone densities of 15 pounds per cubic foot (PCF) and 30 PCF, with a 1-mm-thick simulated cortex. The implant sites were equally distributed among piezoelectric surgery (PES), traditional drills (TD), and black ruby magnetic mallet inserts (MM). Two methods have been employed to evaluate the implant's primary stability, Osstell and micro-tomography. RESULTS: In the present study, we observed significant variations in the implant stability quotient (ISQ) values. More precisely, our findings indicate that the ISQ values were generally higher for 30 PCF compared to 15 PCF. In terms of the preparation technique, PES exhibited the greatest ISQ values, followed by MM, and finally TD. These findings corresponded for both bone densities of 30 PCF (PES 75.6 ± 1.73, MM 69.8 ± 1.91, and TD 65.8 ± 1.91) and 15 PCF (PES 72.3 ± 1.63, MM 62.4 ± 1.77, and TD 60.6 ± 1.81). By utilizing Micro-CT scans, we were able to determine the ratio of the implant occupation to the preparation site. Furthermore, we could calculate the maximum distance between the implant and the wall of the preparation site. The findings demonstrated that PES had a higher ratio of implant to preparation site occupation, followed by TD, and then the MM, at a bone density of 30 PCF (PES 96 ± 1.95, TD 94 ± 1.88, and MM 90.3 ± 2.11). Nevertheless, there were no statistically significant differences in the occupation ratio among these three approaches in the bone density of 15 PCF (PES 89.6 ± 1.22, TD 90 ± 1.31, and MM 88.4 ± 1.17). Regarding the maximum gap between the implant and the site preparation, the smallest gaps were seen when TD were used, followed by MM, and finally by PES, either in a bone density 15 PCF (PES 318 ± 21, TD 238 ± 17, and MM 301 ± 20 µm) or in a bone density 30 PCF (PES 299 ± 20, TD 221 ± 16, and MM 281 ± 19 µm). A statistical analysis using ANOVA revealed these differences to be significant, with p-values of < 0.05. CONCLUSION: The outcomes of this study indicate that employing the PES technique and osteo-densification with MM during implant insertion may enhance the primary stability and increase the possibility of early implant loading.

Mechanical and fatigue resistance of restorations supported by welded-framework and realized using computer-aided designed prosthetic shells: In vitro pilot study.

Resin coating in implants rehabilitation cannot always be aesthetic, durable and comfortable for the patient mainly due to the limited dimensions of the final structure. Intraoral welding technique and computer-aided designed prosthetic shells may be a solution. This in vitro study evaluates the capacity of load and the weakest point of implant-supported provisional prosthesis using welded titanium framework. Twelve samples were produced to simulate an implant supported fixed prosthetic bridge. Two implants (Ankylos; Dentsply Sirona Implants; Germany) were inserted inside blocks of nanoceramic material produced with a stereolithographic 3D printer. A polymethylmethacrylate (PMMA) resin shell was performed with CAD/CAM and relined on welded framework. Six samples were produced with the same procedure reducing resin thickness. The samples were subjected to fatigue test (6,500,000 cycles) using ElectroForce 3310 fatigue machine (t1); subsequently a mechanical compression test using a universal Shimadzu AGS-X 10 machine (t2). The samples were analyzed with a photographic and radiographic documentation at t0, t1 and t2. The samples survived mechanical fatigue test without evidence of failure. The radiographic and photographic evaluation revealed the fracture of resin coating after the mechanical compression test. The samples with minimal resin thickness fractured first. Adequate assessment of the resin thickness is mandatory to improve the longevity of these rehabilitations. CAD-CAM digital prosthetic design allows us to optimize the thicknesses and the prosthetic shapes, allowing us to obtain good degrees of resistance even in the presence of reduced prosthetic spaces.

Influence of ageing on self-etch adhesives: one-step vs. two-step systems.

The aim of this study was to evaluate microtensile bond strength (µTBS) to dentine, interfacial nanoleakage expression, and stability after ageing, of two-step vs. one-step self-etch adhesives. Human molars were cut to expose middle/deep dentine, assigned to groups (n = 15), and treated with the following bonding systems: (i) Optibond XTR (a two-step self-etch adhesive; Kerr), (ii) Clearfil SE Bond (a two-step self-etch adhesive; Kuraray), (iii) Adper Easy Bond (a one-step self-etch adhesive; 3M ESPE), and (iv) Bond Force (a one-step self-etch adhesive; Tokuyama). Specimens were processed for µTBS testing after 24 h, 6 months, or 1 yr of storage in artificial saliva at 37°C. Nanoleakage expression was examined in similarly processed additional specimens. At baseline the µTBS results ranked in the following order: Adper Easy Bond = Optibond XTR ≥Clearfil SE = Bond Force, and interfacial nanoleakage analysis showed Clearfil SE Bond = Adper Easy Bond = Optibond XTR> Bond Force. After 1 yr of storage, Optibond XTR, Clearfil SE Bond, and Adper Easy Bond showed higher µTBS and lower interfacial nanoleakage expression compared with Bond Force. In conclusion, immediate bond strength, nanoleakage expression, and stability over time were not related to the number of steps of the bonding systems, but to their chemical formulations.

Nano-composite scaffolds for bone tissue engineering containing silver nanoparticles: preparation, characterization and biological properties.

In this study nano-composite scaffolds to be used as bone grafts have been endowed with antibacterial properties owing to the presence of silver nanoparticles. The alginate/hydroxyapatite composite scaffolds were prepared by internal gelation followed by a freeze-drying procedure to obtain a porous structure. The nanoparticles were prepared in presence of a lactose modified-chitosan and this colloidal solution was adsorbed on the scaffolds by exploiting electrostatic interactions. The adsorption and release of the silver from the composite scaffold was measured by ICP-AES and spectrofluorimetry measurements. Micro-computed tomography analysis of the scaffolds showed a homogeneous porous structure with average pore sizes of 341.5 µm and porosity of 80 %. In vitro biological tests (MTS and killing kinetics assays) demonstrated that silver does not affect the ability of the scaffolds to promote osteoblasts proliferation and that at the same time it exerts a strong bactericidal effect against both Gram+ and Gram- bacterial strains. Overall, the combined results indicate that these biocompatible antimicrobial scaffolds possess ideal characteristics for tissue engineering applications.

Aging affects the adhesive interface of posts luted with self-adhesive cements: a 1-year study.

PURPOSE: To examine the bond strength and interfacial nanoleakage expression of fiber posts luted to intraradicular dentin with self-adhesive cements. Six-month and 1-year aging effects were examined. MATERIALS AND METHODS: Post space was created in endodontically treated human incisors. Each tooth was assigned to a self-adhesive cement/post combination: (1) Bifix SE Cement (Voco) with proprietary posts (Rebilda Post, Voco), (2) RelyX Unicem (3M ESPE) with proprietary posts (Rely X Fiber Post, 3M ESPE), (3) MaxCem (Kerr) with Rebilda Posts. Each specimen was cut into 1-mm-thick sections and either immediately stressed to failure with the push-out bond strength test or aged in artificial saliva for 6 months or 1 year before testing. Additional specimens were processed for quantitative interfacial nanoleakage analysis using ammoniacal silver nitrate. RESULTS: Immediate bond strength ranked in the following order: Bifix SE (7.8 ± 2.9 MPa) = RelyX Unicem (8.4 ± 2.7 MPa) > MaxCem (4.6 ± 2.4 MPa) (p < 0.05). Aging significantly reduced the bond strength of all cements after 1 year: Bifix SE (3.8 ± 1.4 MPa) = RelyX Unicem (5.8 ± 1.7 MPa) > MaxCem (1.3 ± 0.9 MPa; p<0.05). No immediate difference in interfacial nanoleakage expression was found. Nanoleakage increased after aging, and MaxCem showed the highest values. CONCLUSION: The push-out strength and interfacial nanoleakage expression of fiber posts luted with self-adhesive cements were dependent on luting material and type of post, and were significantly affected by storage time.

Antibacterial and bioactive multilayer electrospun wound dressings based on hyaluronic acid and lactose-modified chitosan.

Antibacterial multilayer electrospun matrices based on hyaluronic acid (HA) and a lactose-modified chitosan (CTL) were synthetized (i) by combining electrospun polycaprolactone (PCL) and polysaccharidic matrices in a bilayer device and (ii) by sequentially coating the PCL mat with CTL and HA. In both cases, the antibacterial activity was provided by loading rifampicin within the PCL support. All matrices disclosed suitable morphology and physicochemical properties to be employed as wound dressings. Indeed, both the bilayer and coated fibers showed an optimal swelling capacity (3426 ± 492 % and 1435 ± 251 % after 7 days, respectively) and water vapor permeability (160 ± 0.78 g/m2h and 170 ± 12 g/m2h at 7 days, respectively). On the other hand, the polysaccharidic dressings were completely wettable in the presence of various types of fluids. Depending on the preparation method, a different release of both polysaccharides and rifampicin was detected, and the immediate polysaccharide dissolution from the bilayer structure impacted the antibiotic release (42 ± 4 % from the bilayer structure against 25 ± 2 % from the coated fibers in 4 h). All the multilayer matrices, regardless of their production strategy and composition, revealed optimal biocompatibility and bioactivity with human dermal fibroblasts, as the released bioactive polysaccharides induced a faster wound closure in the cell monolayer (100 % in 24 h) compared to the controls (78 ± 8 % for untreated cells and 89 ± 5 % for cells treated with PCL alone, after 24 h). The inhibitory and bactericidal effects of the rifampicin loaded matrices were assessed on S. aureus, S. epidermidis, E. coli, and P. aeruginosa. The antibacterial matrices were found to be highly effective except for E. coli, which was more resistant even at higher amounts of rifampicin, with a bacterial concentration of 6.4 ± 0.4 log CFU/mL and 6.8 ± 0.3 log CFU/mL after 4 h in the presence of the rifampicin-loaded bilayer and coated matrices, respectively.

Advantages of agarose on alginate for the preparation of polysaccharide/hydroxyapatite porous bone scaffolds compatible with a proline-rich antimicrobial peptide.

The optimized proline-rich antimicrobial peptide B7-005 was loaded on bone scaffolds based on polysaccharides and hydroxyapatite. Alginate was firstly chosen in order to exploit its negative charges, which allowed an efficient B7-005 loading but hindered its release, due to the strong interactions with the positive charged peptide. Hence, alginate was substituted with agarose which allowed to prepare scaffolds with similar structure, porosity, and mechanical performance than the ones prepared with alginate and hydroxyapatite. Moreover, agarose scaffolds could release B7-005 within the first 24 h of immersion in aqueous environment. The peptide did not impaired MG-63 cell adhesion and proliferation in the scaffold, and a positive cell proliferation trend was observed up to two weeks. The released B7-005 was effective against the pathogensE. coli, K. pneumoniae, andA. baumannii, but not againstS. aureusandP. aeruginosa, thus requiring further tuning of the system to improve its antimicrobial activity.

Correlation of Shear Bond Strength and Degree of Conversion in Conventional and Self-Adhesive Systems Used in Orthodontic Bonding Procedures.

(1) Background: Self-adhesive systems have been proposed for the orthodontic bonding with the intention to reduce the traditional three-component system. (2) Methods: The sample consisted of 32 extracted intact permanent premolars randomly divided into two groups (n = 16). In Group I the metal brackets were bonded with Transbond XT Primer and Transbond XT Paste. In Group II the metal brackets were bonded with GC Ortho connect. The resin was polymerized for 20 s from two directions (mesial and occlusal) using a Bluephase light-curing unit. The shear bond strength (SBS) was measured using a universal testing machine. Immediately after SBS testing, Raman microspectrometry was performed for each sample to calculate the degree of conversion (DC). (3) Results: There was no statistically significant difference in the SBS between the two groups. A significantly higher DC (p < 0.001) value was recorded in Group II, in which the brackets were bonded with GC. Very weak or no correlation (0.01) was recorded between SBS and DC in Group I and moderate positive correlation was recorded in Group II (0.33). (4) Conclusions: No difference was found in SBS between the conventional and two-step systems used in orthodontics. The two-step system demonstrated higher DC compared to the conventional system. There is a very weak or moderate correlation between DC and SBS.