Band gap engineering in blended organic semiconductor films based on dielectric interactions.

Blending organic molecules to tune their energy levels is currently being investigated as an approach to engineer the bulk and interfacial optoelectronic properties of organic semiconductors. It has been proven that the ionization energy and electron affinity can be equally shifted in the same direction by electrostatic effects controlled by blending similar halogenated derivatives with different energetics. Here we show that the energy gap of organic semiconductors can also be tuned by blending. We use oligothiophenes with different numbers of thiophene rings as an example and investigate their structure and electronic properties. Photoelectron spectroscopy and inverse photoelectron spectroscopy show tunability of the single-particle gap, with the optical gaps showing similar, but smaller, effects. Theoretical analysis shows that this tuning is mainly caused by a change in the dielectric constant with blend ratio. Further studies will explore the practical impact of this energy-level engineering strategy for optoelectronic devices.

Emissive and charge-generating donor-acceptor interfaces for organic optoelectronics with low voltage losses.

Intermolecular charge-transfer states at the interface between electron donating (D) and accepting (A) materials are crucial for the operation of organic solar cells but can also be exploited for organic light-emitting diodes1,2. Non-radiative charge-transfer state decay is dominant in state-of-the-art D-A-based organic solar cells and is responsible for large voltage losses and relatively low power-conversion efficiencies as well as electroluminescence external quantum yields in the 0.01-0.0001% range3,4. In contrast, the electroluminescence external quantum yield reaches up to 16% in D-A-based organic light-emitting diodes5-7. Here, we show that proper control of charge-transfer state properties allows simultaneous occurrence of a high photovoltaic and emission quantum yield within a single, visible-light-emitting D-A system. This leads to ultralow-emission turn-on voltages as well as significantly reduced voltage losses upon solar illumination. These results unify the description of the electro-optical properties of charge-transfer states in organic optoelectronic devices and foster the use of organic D-A blends in energy conversion applications involving visible and ultraviolet photons8-11.

Spectroscopic analysis of vibrational coupling in multi-molecular excited states.

Multi-molecular excited states accompanied by intra- and inter-molecular geometric relaxation are commonly encountered in optical and electrooptical studies and applications of organic semiconductors as, for example, excimers or charge transfer states. Understanding the dynamics of these states is crucial to improve organic devices such as light emitting diodes and solar cells. Their full microscopic description, however, demands sophisticated tools such as ab initio quantum chemical calculations which come at the expense of high computational costs and are prone to errors by assumptions as well as iterative algorithmic procedures. Hence, the analysis of spectroscopic data is often conducted at a phenomenological level only. Here, we present a toolkit to analyze temperature dependent luminescence data and gain first insights into the relevant microscopic parameters of the molecular system at hand. By means of a Franck-Condon based approach considering a single effective inter-molecular vibrational mode and different potentials for the ground and excited state we are able to explain the luminescence spectra of such multi-molecular states. We demonstrate that by applying certain reasonable simplifications the luminescence of charge transfer states as well as excimers can be satisfactorily reproduced for temperatures ranging from cryogenics to above room temperature. We present a semi-classical and a quantum-mechanical description of our model and, for both cases, demonstrate its applicability by analyzing the temperature dependent luminescence of the amorphous donor-acceptor heterojunction tetraphenyldibenzoperiflanthene:C60 as well as polycrystalline zinc-phthalocyanine to reproduce the luminescence spectra and extract relevant system parameters such as the excimer binding energy.

On the origin of the open-circuit voltage of polymer-fullerene solar cells.

The increasing amount of research on solution-processable, organic donor-acceptor bulk heterojunction photovoltaic systems, based on blends of conjugated polymers and fullerenes has resulted in devices with an overall power-conversion efficiency of 6%. For the best devices, absorbed photon-to-electron quantum efficiencies approaching 100% have been shown. Besides the produced current, the overall efficiency depends critically on the generated photovoltage. Therefore, understanding and optimization of the open-circuit voltage (Voc) of organic solar cells is of high importance. Here, we demonstrate that charge-transfer absorption and emission are shown to be related to each other and Voc in accordance with the assumptions of the detailed balance and quasi-equilibrium theory. We underline the importance of the weak ground-state interaction between the polymer and the fullerene and we confirm that Voc is determined by the formation of these states. Our work further suggests alternative pathways to improve Voc of donor-acceptor devices.

Electroluminescence from charge transfer states in polymer solar cells.

In this article we report the weak but omnipresent electroluminescence (EL) from several types of organic polymer:fullerene bulk heterojunction solar cells biased in the forward direction. The light emitted from blends of some commonly used polymers and the fullerene molecule is significantly different from that of any of the pure materials comprising the blend. The lower energy of the blend EL is found to correlate with both the voltage onset of emission and the open-circuit voltage of the photovoltaic cell under solar illumination. We accordingly interpret the emission to originate from interfacial charge transfer state recombination and emphasize EL as a very valuable tool to characterize the charge transfer state present in donor/acceptor organic photovoltaic (OPV) cells.

Trapping light with micro lenses in thin film organic photovoltaic cells.

We demonstrate a novel light trapping configuration based on an array of micro lenses in conjunction with a self aligned array of micro apertures located in a highly reflecting mirror. When locating the light trapping element, that displays strong directional asymmetric transmission, in front of thin film organic photovoltaic cells, an increase in cell absorption is obtained. By recycling reflected photons that otherwise would be lost, thinner films with more beneficial electrical properties can effectively be deployed. The light trapping element enhances the absorption rate of the solar cell and increases the photocurrent by as much as 25%.

Impact of Interfaces and Laser Repetition Rate on Photocarrier Dynamics in Lead Halide Perovskites.

We studied charge carrier recombination in methylammonium lead iodide (MAPbI3) perovskite and the impact of interfaces on the charge carrier lifetime using time-resolved photoluminescence. Pristine films and those covered with organic electron and hole transport materials (ETM and HTM) were investigated at various laser repetition rates ranging from 10 kHz to 10 MHz in order to separate the bulk and interface-affected recombination. We revealed two different components in the PL decay. The fast component (shorter than 300 ns) is assigned to interfacial processes and the slow one to bulk recombination. A high repetition pulse train was shown to shorten PL decay in pristine perovskite while significantly prolonging the photocarrier lifetime in MAPbI3 covered by TMs. This effect can be qualitatively explained with a kinetic model taking interface traps into account. We demonstrate a significant influence of the excitation repetition rate on photocarrier lifetime, which should be considered when studying charge carrier dynamics in perovskites.

Improved charge carrier lifetime in planar perovskite solar cells by bromine doping.

The charge carrier lifetime is an important parameter in solar cells as it defines, together with the mobility, the diffusion length of the charge carriers, thus directly determining the optimal active layer thickness of a device. Herein, we report on charge carrier lifetime values in bromine doped planar methylammonium lead iodide (MAPbI3) solar cells determined by transient photovoltage. The corresponding charge carrier density has been derived from charge carrier extraction. We found increased lifetime values in solar cells incorporating bromine compared to pure MAPbI3 by a factor of ~2.75 at an illumination intensity corresponding to 1 sun. In the bromine containing solar cells we additionally observe an anomalously high value of extracted charge, which we deduce to originate from mobile ions.

Identification of Trap States in Perovskite Solar Cells.

Thermally stimulated current (TSC) measurements are used to characterize electronic trap states in methylammonium lead iodide perovsite solar cells. Several TSC peaks were observed over the temperature range from 20 K to room temperature. To elucidate the origins of these peaks, devices with various organic charge transport layers and devices without transport layers were tested. Two peaks appear at very low temperatures, indicating shallow trap states that are mainly attributed to the PCBM/C60 electron transport bilayer. However, two additional peaks appear at higher temperatures, that is, they are deeper in energy, and are assigned to the perovskite layer. At around T = 163 K, a sharp peak, also present in the dark TSC measurements, is assigned to the orthorhombic-tetragonal phase transition in the perovskite. However, a peak at around T = 191 K is assigned to trap states with activation energies of around 500 meV but with a rather low concentration of 1 × 10(21) m(-3).

Radiative efficiency of lead iodide based perovskite solar cells.

The maximum efficiency of any solar cell can be evaluated in terms of its corresponding ability to emit light. We herein determine the important figure of merit of radiative efficiency for Methylammonium Lead Iodide perovskite solar cells and, to put in context, relate it to an organic photovoltaic (OPV) model device. We evaluate the reciprocity relation between electroluminescence and photovoltaic quantum efficiency and conclude that the emission from the perovskite devices is dominated by a sharp band-to-band transition that has a radiative efficiency much higher than that of an average OPV device. As a consequence, the perovskite have the benefit of retaining an open circuit voltage ~0.14 V closer to its radiative limit than the OPV cell. Additionally, and in contrast to OPVs, we show that the photoluminescence of the perovskite solar cell is substantially quenched under short circuit conditions in accordance with how an ideal photovoltaic cell should operate.

Interlayer for modified cathode in highly efficient inverted ITO-free organic solar cells.

Inverted polymer solar cells with a bottom metal cathode modified by a conjugated polymer interlayer show considerable improvement of photocurrent and fill factor, which is due to hole blocking at the interlayer, and a modified surface energy which affects the nanostructure in the TQ1/[70]PCBM blend.

Polymer photovoltaics with alternating copolymer/fullerene blends and novel device architectures.

The synthesis of novel conjugated polymers, designed for the purpose of photovoltaic energy conversion, and their properties in polymer/fullerene materials and photovoltaic devices are reviewed. Two families of main-chain polymer donors, based on fluorene or phenylene and donor-acceptor-donor comonomers in alternating copolymers, are used to absorb the high-energy parts of the solar spectrum and to give high photovoltages in combinations with fullerene acceptors in devices. These materials are used in alternative photovoltaic device geometries with enhanced light incoupling to collect larger photocurrents or to enable tandem devices and enhance photovoltage.

Bridging dimensions in organic electronics: assembly of electroactive polymer nanodevices from fluids.

Processing and patterning of electroactive materials from solvents is a hallmark of flexible organic electronics, and commercial applications based on these properties are now emerging. Printing and ink-jetting are today preferred technologies for patterning, but these limit the formation of nanodevices, as they give structures way above the micrometer lateral dimension. There is therefore a great need for cheap, large area patterning of nanodevices and methods for top-down registration of these. Here we demonstrate large area patterning of connected micro/nanolines and nanotransistors from the conducting polymer PEDOT, assembled from fluids. We thereby simultaneously solve problems of large area nanopatterning, and nanoregistration.