A Capacitively-Fed Inverted-F Antenna for Displacement Detection in Structural Health Monitoring.

This paper presents a capacitive displacement sensor based on a capacitively fed inverted-F antenna (CFIFA) for displacement detection. The sensor is composed of a grounded L-shape patch and a rectangular upper patch, forming a capacitor between them. The asymmetric dipole model is adopted to explain the frequency shift and current distribution of the proposed antenna sensor at its first-order resonance. The numerical simulation of the CFIFA using the Ansoft high-frequency structure simulator (HFSS) software is carried out to optimize the dimensional parameters, allowing the antenna to perform better. Two sets of CFIFAs are fabricated and tested for verification. Results show that the CFIFA has a good linear relationship between its first resonant frequency and the relative displacement, and is capable of a long range of displacement measuring.

Long-Range Displacement Meters Based on Chipped Circular Patch Antenna.

This paper presents a passive wireless long-range displacement sensor that is based on the circular patch antenna, and the detecting range of the sensor can be customized. The sensor consists of a chipped circular antenna with two opened rectangular windows, a substrate, and a ground plate with a sloping channel. No bonding between the antenna and the ground plate allows for the chipped antenna to slide along the sloping channel. The channel will drive the current flow on the plate once the chip is activated, increasing the effective electrical length and, consequently, decreasing the resonant frequency of the circular antenna. The sensing mechanism equates the measuring displacement to the relative movement of the antenna with respect to the ground that achieves the measurement of long-range displacement and, thus, the proposed sensor can avoid stress damage to the antenna due to excessive deformation. Three different range sensors were simulated in the the Ansoft high frequency structure simulator (HFSS). The results show that the resonance frequency of the antenna has a linear relationship with the varying chute depth beneath the chip. Three sensors were fabricated, and the experimental results also validated that the sensitivity of the sensor can be adjusted.

Polyelectrolyte-promoted forward osmosis-membrane distillation (FO-MD) hybrid process for dye wastewater treatment.

Polyelectrolytes have proven their advantages as draw solutes in forward osmosis process in terms of high water flux, minimum reverse flux, and ease of recovery. In this work, the concept of a polyelectrolyte-promoted forward osmosis-membrane distillation (FO-MD) hybrid system was demonstrated and applied to recycle the wastewater containing an acid dye. A poly(acrylic acid) sodium (PAA-Na) salt was used as the draw solute of the FO to dehydrate the wastewater, while the MD was employed to reconcentrate the PAA-Na draw solution. With the integration of these two processes, a continuous wastewater treatment process was established. To optimize the FO-MD hybrid process, the effects of PAA-Na concentration, experimental duration, and temperature were investigated. Almost a complete rejection of PAA-Na solute was observed by both FO and MD membranes. Under the conditions of 0.48 g mL(-1) PAA-Na and 66 °C, the wastewater was most efficiently dehydrated yet with a stabilized PAA-Na concentration around 0.48 g mL(-1). The practicality of PAA-Na-promoted FO-MD hybrid technology demonstrates not only its suitability in wastewater reclamation, but also its potential in other membrane-based separations, such as protein or pharmaceutical product enrichment. This study may provide the insights of exploring novel draw solutes and their applications in FO related processes.

Crack detection for concrete bridges with imaged based deep learning.

Within the framework of intelligent bridge detection, a number of crack detection methods based on image processing techniques have been implemented. In this study, a combined novel approach with deep learning of a single shot multibox detector (SSD) and the eight neighborhood algorithm is proposed and applied to bridge crack image identification to provide an automatic method for crack detection. First, a large number of concrete crack images collected from the site were segmented and preprocessed for the establishment of a crack image dataset. Deep learning of the SSD algorithm was introduced on the training set to establish the detection model, where the model parameters were adjusted by the validation set. Sliding window technology was integrated to identify the cracks in the test set. The effects of the sliding window size and dataset size on the crack detection results were discussed. Moreover, the eight neighborhood algorithm was adopted for further crack detection correction. The results show that the configuration achieves good crack detection by the deep learning of the SSD algorithm with high precision and recall. The introduction of the eight neighborhood correction algorithm further improves the detection results by eliminating some misjudged results. Finally, the developed algorithm was placed into a portable device, with which cracks were effectively identified. The introduced method shows significantly better performance in crack detection, and the system installed on the portable device provides a way to broaden its application in the automatic crack detection of concrete bridges.

Pulse-heating infrared thermography inspection of bonding defects on carbon fiber reinforced polymer composites.

Non-destructive analysis of fiber reinforced polymer (FRP) composites is important for confirming the long-term safety and durability of concrete structures. In this study, a pulse-heating infrared thermography technique was used to detect and characterize bonding defects of externally bonded carbon fiber reinforced polymers (CFRP) on concrete surface structures. The CFRP composite contains various bonding defects of three different sizes located at five different depths. Sequential thermal images were obtained to describe the temperature contrast and shapes of the bonding defects. Through analysis of the maximum temperature response, we investigated the effects of defect size and depth on the defect temperature response. The relationship between the defect depth and maximum temperature response was used to quantitatively estimate the defect depth. In addition, finite element simulations were performed on the CFRP composites with bonding defects to investigate the temperature response of various defects, which showed good agreement with the experimental results. This confirms the effectiveness of the infrared thermography method to detect and characterize bonding defects of FRP composites bonded on concrete structures.

Experimental Study on Force Sensitivity of the Conductivity of Carbon Nanotubes-Modified Epoxy Resins.

The addition of a conductive material into polymer improves its mechanical properties, electrical properties and thermal conductivity and bestows it with good self-sensing and self-adjusting properties. In this study, carbon nanotubes-modified epoxy resins (CNTs-EP) were successfully prepared with good dispersion through the combined methods of three roller rolling, ultrasonic processing and adding surfactant. Tests were conducted to evaluate the resistivity of unloaded modified epoxy resins with different mixing amounts of carbon nanotubes (CNTs), to determine the conductive percolation threshold. On the basis of the test results, a series of monotonic and cyclic uniaxial tensile tests were then conducted to investigate the force sensitivity of the conductivity of epoxy resins modified with different mixing amounts of CNTs. The relationship between the stress and the resistivity under various mixing amounts was studied, indicating that the resistance response could play a good warning role on the damage of the modified polymer material.

Investigations of inorganic and organic fouling behaviors, antifouling and cleaning strategies for pressure retarded osmosis (PRO) membrane using seawater desalination brine and wastewater.

By employing seawater desalination brine (SWBr) and wastewater brine (WWBr) as the feed pair, membrane fouling behaviors as well as antifouling and cleaning strategies for the state-of-the-art thin-film composite polyethersulfone (TFC-PES) hollow fiber membrane have been systematically investigated under pressure retarded osmosis (PRO) operations. Fouling on the polyamide selective layer induced by the SWBr draw solution is relatively mild because of the outstanding membrane rejection and the hydration antifouling layer formed by the permeating water. However, using WWBr as the feed causes fast and severe internal concentration polarization (ICP) and fouling within the porous PES substrate, which result in dramatic flux and power density declines. In addition, the PRO fouling upon and within the porous substrate is highly irreversible. Experimental data show that both anti-scalant pretreatment and pH adjustment of WWBr could effectively mitigate inorganic fouling, while increasing feed flow velocity along the substrate surface is ineffective for fouling control. To clean the fouled membranes, hydraulic-pressure induced backwash and flushing with alkaline and NaOCl solutions on the fouled surface are effective strategies to remove foulants and regenerate membranes with a flux recovery of 83-90%. However, osmotic backwash shows low cleaning efficiency in PRO. In summary, a proper combination of feed pretreatment and membrane cleaning strategies has been demonstrated in this study to sustain PRO operations with a high water flux and power density.

Zwitterions coated hollow fiber membranes with enhanced antifouling properties for osmotic power generation from municipal wastewater.

Fouling on pressure-retarded osmosis (PRO) membranes leads to severe declines in water flux and power density because their porous substrates are facing the wastewater feed. Thus, inorganics, organics and microorganisms in the wastewater are prone to depositing on the substrate surface and even in its pores. In order to reduce the fouling propensity, coating the substrate surface of PRO membranes with zwitterionic materials proves to be an effective way. In this work, 2-methacryloyloxyethylphosphorylcholine (MPC), is modified and grafted onto the polydopamine (PDA) coated poly (ether sulfone) (PES) hollow fiber substrate. Both the synthesis and surface coating of MPC are easy and facile to be scaled up. Compared with the pristine PES and PES-PDA substrates, the MPC modified substrate (PES-PDA-MPC) exhibits high resistance to protein adsorption as well as bacteria adhesion. By using a state-of-the-art thin-film composite poly (ether sulfone) (TFC-PES) hollow fiber membrane as the control for power generation, the power density of the TFC-PES-PDA-MPC membrane can achieve as high as 7.7 W/m2 while the unmodified one has only 6.0 W/m2 after 3 h's PRO tests. In conclusion, the osmotic power generation of PRO membranes can be significantly sustained by modifying the membrane surface with zwitterions.

Integrated honeycomb technology motivated by the structure of beetle forewings.

The authors' previously presented architecture of beetle forewings has become the source of motivation for developing an integrated honeycomb structure. In this paper, we briefly review this architecture, describe the characteristics of this proposed novel structure, and, show that the beetle forewing contains a fully integrated honeycomb plate rather than a traditional "honeycomb" structure. Herein, a basic geometrical model of the fiber orientation is also provided, and how to develop an integrated honeycomb technology is discussed. By assuming that each hexagonal space of the honeycomb is filled with a male tool and a continuous plate is built, we consider disassembling the plate into a limited number of basic male tools and a honeycomb plate. The male tools were made with paraffin wax, and basalt fiber meshes were laid inside the female tool. We injected a mixture of shredded basalt fiber and epoxy resin into the mold for making a prototype structure. After solidification at a low temperature followed by the removal of the male tools via heating, an integrated honeycomb plate with trabeculae inside the honeycomb was manufactured. We consider that the proposed manufacturing process, which does not need bonding, is a breakthrough and it is envisioned that it will introduce an alternative to the traditional assembly method of manufacturing honeycomb plates.