RESUMEN
A decrease in CO2 emissions is urgently required in the present situation due to the fast growth of carbon dioxide (CO2) in the atmosphere, which has caused a series of global climate issues. This study used an impregnation-evaporation method to immobilize an amino functionalized ionic liquid [C2OHmim][Lys] on a chromatographic column filler GDX-103 and create a novel supported ionic liquid. The results showed that the supported ionic liquid with 60 wt % ionic liquid content had the best adsorption performance at 40 °C, and the CO2 adsorption isotherm showed that the adsorption capacity at 0.1 MPa was 1.29 mmol CO2/g sorbent, which was 6 times greater than the adsorption capacity of the pure carrier. The sample with 60% ionic liquid content has an adsorption capacity of 1.02 mmol CO2/g sorbent under the condition of CO2/N2 mixed gas with 10% CO2 content. This is 43 times greater than the adsorption capacity of the pure carrier, and its adsorption performance is stable after three adsorption and desorption cycles. Through the rich porous structure of GDX-103, the ionic liquid is effectively supported and dispersed, which expands the contact area between CO2 and ionic liquid and enhances the mass transfer of CO2. At the same time, CO2 can be chemically bound to the groups on the anion of ionic liquid and be immobilized, so it has a high selective adsorption capacity of CO2, which makes it a great alternative to traditional CO2 adsorbents.
RESUMEN
Developing non-noble-metal electrocatalysts for hydrogen evolution reactions with high activity and stability is the key issue in green hydrogen generation based on electrolytic water splitting. It has been recognized that the stacking of large CoP particles limits the intrinsic activity of as-synthesized CoP catalyst for hydrogen evolution reaction. In the present study, N-MoxC/CoP-0.5 with excellent electrocatalytic activity for hydrogen evolution reaction was prepared using N-MoxC as decoration. A reasonable overpotential of 106 mV (at 10 mA cm-2) and a Tafel slope of 59 mV dec-1in 1.0 M KOH solution was achieved with N-MoxC/CoP-0.5 electrocatalyst, which exhibits superior activity even after working for 37 h. Uniformly distributed ultrafine nanoclusters of the N-MoxC/CoP-0.5 hybrids could provide sufficient interfaces for enhanced charge transfer. The effective capacity of the hydrogen evolution reaction could be preserved in the complex, and the enlarged electrocatalytic surface area could be expected to offer more active sites for the reaction.
RESUMEN
Capparis spinosa L. (CSL) is used in traditional medicinal purposes for wound dressing because it contains natural phenolic and flavonoid active compounds. In the current study, a bilayer of biocompatible and mechanically stable nanofiber scaffolds with polycaprolactone (PCL)/zinc oxide and Capparis spinosa L. ethyl acetate extract (CSLE)/polylactic acid (PLA) layers was successfully prepared by an electrostatic spinning technique. Microstructural observations carried out by scanning electron microscopy (SEM) have shown that the nanofibers with a smooth surface are continuous and bead-free, and that the size distribution is uniform, with an average diameter of 314.15 nm. The results of careful observation further suggested that polymers in the nanofibers have excellent compatibility with drugs. The results of Fourier transform infrared (FTIR) spectroscopy suggested that CSLE and zinc oxide nanoparticles (ZnO) were successfully loaded in the nanofiber membranes. Water contact angle measurements revealed that the bilayer nanofiber membranes exhibited satisfactory wettability (outside layer, 130°; inner layer, 72.4°). Tensile testing showed that the bilayer PCL/ZnO-CSLE/PLA nanofibers remained unbroken until reaching 10.69 MPa, which is much higher than the tensile strengths of the individual layers or the individual components. Moreover, agar disk diffusion assessment confirmed that the bilayer nanofiber membranes obviously hindered bacterial growth. Cytotoxicity studies showed that the bilayer nanofiber membranes effectively accelerated cell proliferation. The investigated PCL/ZnO-CSLE/PLA bilayer nanofibers have potential for use as membranes for wound dressing applications.