Spatial organization and connectivity of wood rays in Pinus massoniana xylem based on high-resolution µCT-assisted network analysis.

MAIN CONCLUSION: Spatial organization and connectivity of wood rays in Pinus massoniana was comprehensively viewed and regarded as anatomical adaptions to ensure the properties of rays in xylem. Spatial organization and connectivity of wood rays are essential for understanding the wood hierarchical architecture, but the spatial information is ambiguous due to small cell size. Herein, 3D visualization of rays in Pinus massoniana was performed using high-resolution µCT. We found brick-shaped rays were 6.5% in volume fractions, nearly twice the area fractions estimated by 2D levels. Uniseriate rays became taller and wider during the transition from earlywood to latewood, which was mainly contributed from the height increment of ray tracheids and widened ray parenchyma cells. Furthermore, both volume and surface area of ray parenchyma cells were larger than ray tracheids, so ray parenchyma took a higher proportion in rays. Moreover, three different types of pits for connectivity were segmented and revealed. Pits in both axial tracheids and ray tracheids were bordered, but the pit volume and pit aperture of earlywood axial tracheids were almost tenfold and over fourfold larger than ray tracheids. Contrarily, cross-field pits between ray parenchyma and axial tracheids were window-like with the principal axis of 31.0 µm, but its pit volume was approximately one-third of axial tracheids. Additionally, spatial organization of rays and axial resin canal was analyzed by a curved surface reformation tool, providing the first evidence of rays close to epithelial cells inward through the resin canal. Epithelial cells had various morphologies and large variations in cell size. Our results give new insights into the organization of radial system of xylem, especially the connectivity of rays with adjacent cells.

Fabricable concentric-ring metalens with high focusing efficiency based on two-dimensional subwavelength unit splicing.

To address the challenges posed by computational resource consumption and data volume in the development of large-aperture metalenses, a design method for concentric-ring metalens based on two-dimensional unit splicing is proposed in this paper. In the method, the unit structure library is constructed through global traversal under the machining process constraints. The phase matching is performed for two polarization states with specific weights and the design of binary-height, concentric-ring structures with arbitrary polarization sensitivity is realized, whose focusing efficiency (the encircled power within 3×FWHM of the focal spot divided by the near-field outgoing power) is up to 90%. Based on this method, a polarization-insensitive metalens with a design wavelength of 10µm, diameter of 2 cm, and numerical aperture of 0.447 is obtained. The method combines the advantages of lower computation requirements for a building block array of a metalens and lower structure data for a concentric-ring metalens. Consequently, it becomes possible to reduce calculation and processing costs by several orders of magnitude during the development process of metalenses with diameters ranging from 103 to 105 wavelengths. The resulting focusing efficiency can approach the upper limit achievable through global structural optimization and significantly surpass that of binary-height Fresnel lenses.

Positional differences in the micro- and ultra-structural variations of ray parenchyma cells during the transformation from sapwood to heartwood.

Ray parenchyma cells are involved in the initiation of heartwood formation. The position within a ray influences the timing of ray parenchyma cell differentiation and function; however, there is little information concerning the positional influence on the cellular changes of ray parenchyma cells from sapwood and heartwood. In this study, radial variations in morphology, size, and ultrastructure of ray parenchyma cells were studied by combined transmission electron microscopy and optical microscopy. Results showed that cellular traits of ray parenchyma cells in Populus tomentosa were all affected by both radial position in the secondary xylem and position within a ray. Specifically, radial variations in cellular traits were more evident in isolation cells, which were not adjacent to vessel elements. Both cell length and cell width/length ratio of isolation cells were bigger than contact cells, which contacted adjacent vessel elements via pits. Moreover, the secondary wall thickening and lignification of contact cells developed in the current-year xylem, much earlier than isolation cells. Secondary walls in contact cells were in a polylamellate structure with a protective layer on the inner side. No alteration in the ultrastructure of contact cells occurred in the sapwood-heartwood transition zone, except that most contact cells died. By contrast, in the transition zone, isolation cells still lived. A thin secondary wall began to deposit on the thick primary wall of isolation cells, with two isotropic layers on the inner side of the primary wall and secondary wall respectively being characteristic. Meanwhile, starch grains in isolation cells were depleted, and dark polyphenolic droplets lost their spherical shape and flowed together. Furthermore, the intercellular spaces of isolation cells became densified in the transition zone. Overall, cellular changes suggested that the positional information of ray parenchyma cells appeared to be an important factor in the transformation from sapwood to heartwood. Unlike contact cells, isolation cells were more elongated, specialized in radial transport, had a delayed formation of secondary walls, and were involved in the synthesis of heartwood substances. Our result promotes the elucidation of the involvement of xylem rays in heartwood formation.

High-Efficiency Achromatic Metalens Topologically Optimized in the Visible.

Metalens, composed of arrays of nano-posts, is an ultrathin planar optical element used for constructing compact optical systems which can achieve high-performance optical imaging by wavefront modulating. However, the existing achromatic metalenses for circular polarization possess the problem of low focal efficiency, which is caused by the low polarization conversion efficiencies of the nano-posts. This problem hinders the practical application of the metalens. Topology optimization is an optimization-based design method that can effectively extend the degree of design freedom, allowing the phases and polarization conversion efficiencies of the nano-posts to be taken into account simultaneously in the optimization procedures. Therefore, it is used to find geometrical configurations of the nano-posts with suitable phase dispersions and maximized polarization conversion efficiencies. An achromatic metalens has a diameter of 40 µm. The average focal efficiency of this metalens is 53% in the spectrum of 531 nm to 780 nm by simulation, which is higher than the previously reported achromatic metalenses with average efficiencies of 20~36%. The result shows that the introduced method can effectively improve the focal efficiency of the broadband achromatic metalens.