A series of perylene diimide cathode interlayer materials for green solvent processing in conventional organic photovoltaics.

Herein, we report on the design, synthesis, physical and chemical properties, and organic photovoltaic (OPV) device performance of four new cathode interlayer (CIL) materials based on bay N-annulated perylene diimides. Starting from the previously reported N-annulated perylene diimide (PDIN-H), the N-position was functionalized with a benzyl and pentafluorobenzyl group to make PDIN-B and PDIN-FB, respectively. Similarly, starting from the previously reported cyanated N-annulated perylene diimide (CN-PDIN-H), the N-position was functionalized with a benzyl and pentafluorobenzyl group to make CN-PDIN-B and CN-PDIN-FB, respectively. The materials exhibit solubility in the green solvent, ethyl acetate, and thus were processed into thin films using ethyl acetate as the solvent. The optoelectronic properties were assessed for both solution and film, and the electrochemical properties were probed in solution. To validate the potential as electron transporting layers, each film was used in conventional OPVs as the CIL with processing from ethyl acetate, while using a bulk heterojunction (BHJ) comprised of PM6:Y6. High power conversion efficiencies (PCEs) of 13% were achieved compared to control devices using the standard PFN-Br CIL.

Lowering Electrocatalytic CO2 Reduction Overpotential Using N-Annulated Perylene Diimide Rhenium Bipyridine Dyads with Variable Tether Length.

We report the design, synthesis, and characterization of four N-annulated perylene diimide (NPDI) functionalized rhenium bipyridine [Re(bpy)] supramolecular dyads. The Re(bpy) scaffold was connected to the NPDI chromophore either directly [Re(py-C0-NPDI)] or via an ethyl [Re(bpy-C2-NPDI)], butyl [Re(bpy-C4-NPDI)], or hexyl [Re(bpy-C6-NPDI)] alkyl-chain spacer. Upon electrochemical reduction in the presence of CO2 and a proton source, Re(bpy-C2/4/6-NPDI) all exhibited significant current enhancement effects, while Re(py-C0-NPDI) did not. During controlled potential electrolysis (CPE) experiments at Eappl = -1.8 V vs Fc+/0, Re(bpy-C2/4/6-NPDI) all achieved comparable activity (TONco ∼ 25) and Faradaic efficiency (FEco ∼ 94%). Under identical CPE conditions, the standard catalyst Re(dmbpy) was inactive for electrocatalytic CO2 reduction; only at Eappl = -2.1 V vs Fc+/0 could Re(dmbpy) achieve the same catalytic performance, representing a 300 mV lowering in overpotential for Re(bpy-C2/4/6-NPDI). At higher overpotentials, Re(bpy-C4/6-NPDI) both outperformed Re(bpy-C2-NPDI), indicating the possibility of coinciding electrocatalytic CO2 reduction mechanisms that are dictated by tether-length and overpotential. Using UV-vis-nearIR spectroelectrochemistry (SEC), FTIR SEC, and chemical reduction experiments, it was shown that the NPDI-moiety served as an electron-reservoir for Re(bpy), thereby allowing catalytic activity at lower overpotentials. Density functional theory studies probing the optimized geometries and frontier molecular orbitals of various catalytic intermediates revealed that the geometric configuration of NPDI relative to the Re(bpy)-moiety plays a critical role in accessing electrons from the electron-reservoir. The improved performance of Re(bpy-C2/4/6-NPDI)dyads at lower overpotentials, relative to Re(dmbpy), highlights the utility of chromophore electron-reservoirs as a method for lowering the overpotential for CO2 conversion.

Development of Organic Dye-Based Molecular Materials for Use in Fullerene-Free Organic Solar Cells.

This personal account describes the pursuit of non-fullerene acceptors designed from simple and accessible organic pi-conjugated building blocks and assembled through efficient direct (hetero)arylation cross-coupling protocols. Initial materials development focused on isoindigo and diketopyrrolopyrrole organic dyes flanked by imide-based terminal acceptors. Efficiencies in solution-processed organic solar cells were modest but highlighted the potential of the material design. Materials performance was improved through structural engineering to pair perylene diimide with these organic dyes. Optimization of active layer processing and solar cell device fabrication identified the perylene diimide flanked diketopyrrolopyrrole structure as the best framework, with fullerene-free organic solar cells achieving power conversion efficiencies above 6 %. This material has met our criteria for a simple wide band gap fullerene alternative for pairing with a range of donor polymers.

Additive induced crystallization of a twisted perylene diimide dimer within a polymer matrix.

The controlled aggregation of organic π-conjugated molecular semiconductors within a host material (often a polymer) is important for obtaining appropriate organic film morphologies and mechanical properties for optoelectronic applications. In this study, we demonstrate how we have challenged the twisting effect in perylene diimide dimers, which is known to hinder their aggregation. Indeed, a twisted N-annulated perylene diimide dimer (tPDI2N-EH) can be induced to form crystalline aggregates within a host poly-3-hexylthiophene (P3HT) polymer matrix using solution processing. The size of the aggregates can be controlled using varying amounts of the common processing solvent additive 1,8-diiodooctane (DIO) during film formation, by changing the concentration of the molecule within the polymer film, and by adjusting the film drying time. A combination of UV-visible spectroscopy, fluorescence microscopy, cross-polarized light microscopy, and atomic force microscopy were used to characterize the organic films.

Direct (Hetero)Arylation for the Synthesis of Molecular Materials: Coupling Thieno[3,4-c]pyrrole-4,6-dione with Perylene Diimide to Yield Novel Non-Fullerene Acceptors for Organic Solar Cells.

Herein we report on the synthesis of an N-annulated perylene diimide (PDI) disubstituted thieno[3,4-c]pyrrole-4,6-dione (TPD) molecular acceptor (PDI-TPD-PDI) by direct heteroarylation (DHA) methods. Three sets of DHA conditions that explore the effects of solvent, temperature, and catalyst were employed to find the optimal conditions for the synthesis of two PDI-TPD-PDI derivatives. We then selected one PDI-TPD-PDI for use as a non-fullerene acceptor in organic solar cell devices with the donor polymer PBDB-T. Active layer bulk-heterojunction blends were modified using several post-deposition treatments, including thermal annealing, solvent vapour annealing, and high boiling solvent additives. It was found that active layers cast from o-dichlorobenzene with a 3% v/v diphenylether additive yielded films with adequate phase separation, and subsequently gave the best organic solar cell performance, with power conversion efficiencies greater than 3%.

Direct (Hetero)Arylation Polymerization of a Spirobifluorene and a Dithienyl-Diketopyrrolopyrrole Derivative: New Donor Polymers for Organic Solar Cells.

The synthesis and preliminary evaluation as donor material for organic photovoltaics of the poly(diketopyrrolopyrrole-spirobifluorene) (PDPPSBF) is reported herein. Prepared via homogeneous and heterogeneous direct (hetero)arylation polymerization (DHAP), through the use of different catalytic systems, conjugated polymers with comparable molecular weights were obtained. The polymers exhibited strong optical absorption out to 700 nm as thin-films and had appropriate electronic energy levels for use as a donor with PC70BM. Bulk heterojunction solar cells were fabricated giving power conversion efficiencies above 4%. These results reveal the potential of such polymers prepared in only three steps from affordable and commercially available starting materials.

Optimized synthesis of π-extended squaraine dyes relevant to organic electronics by direct (hetero)arylation and Sonogashira coupling reactions.

This study reports on the synthesis and characterization of four molecular π-extended squaraine compounds relevant to the field of organic electronics. The compounds each consist of a bis-indole squaraine core end-capped with indoloquinoxaline units employing three different bridging units, namely thiophene, thiazole, and acetylene. Compound 10 bears a thiophene bridge, 11 consists of a thiophene bridge and fluorinated indoloquinoxaline terminal units, and compounds 12 and 13 are bridged by thiazole and acetylene, respectively. The final compounds are constructed using the atom economical direct (hetero)arylation or the classic Sonogashira carbon-carbon bond formation protocols. Each carbon-carbon bond forming reaction employing thiophene bridges (i.e. synthesis of compounds 10 and 11) has been optimized using the stable and reusable silica supported Pd catalyst, SiliaCat® DPP-Pd, streamlining the synthetic procedure. While compounds 12 and 13 were also accessible using the SiliaCat® DPP-Pd catalyst, the use of Herrmann-Beller and Pd(PPh3)4 catalysts, respectively, lead to improved isolated yields of the final materials. Compounds 10-13 were characterized by thermal gravimetric analysis, cyclic voltammetry, optical absorption spectroscopy, photoluminescence spectroscopy, and each structure was analysed using density functional theory. All compounds exhibit high thermal stability and good solubility in common organic solvents, including in the greener alternative 2-methyl tetrahydrofuran. The reported compounds display stable ambipolar redox behaviour, furthermore, we have demonstrated that the frontier molecular energy levels can be effectively tuned by changing the bridging unit as predicted by density functional theory. Most striking is the drastic optical absorption profile changes observed from this class of materials upon post-deposition film annealing, suggesting molecular rearrangement in the solid-state. The induced changes and fine structure observed upon post-deposition annealing is unique to these π-extended squaraines with nothing like it reported in the literature for related squaraine based materials.

Synthesis and structure-property relationships of phthalimide and naphthalimide based organic π-conjugated small molecules.

Five organic π-conjugated small molecules with bithiophene-phthalimide backbones bearing alkyl chains of different symmetry, length and branching character were synthesized using optimized microwave and direct heteroarylation protocols. The chosen alkyl chains were 1-ethylpropyl, 1-methylbutyl, pentyl, hexyl and octyl. A sixth compound was also synthesized replacing the phthalimide terminal units with octylnaphthalimide for additional scope. Through the thorough analysis of both thermal and optical properties and the investigation of self-assembly tendencies by single crystal X-ray diffraction and variable angle spectroscopic ellipsometry it is evident that alkyl side chains and building block size influence many facets of material properties. Within this class of materials the 1-ethylpropyl derivative exhibited the most unique behaviour.

Understanding the morphology of solution processed fullerene-free small molecule bulk heterojunction blends.

Bulk-heterojunction (BHJ) molecular blends prepared from small molecules based on diketopyrrolopyrrole (DPP) and perylene-diimide (PDI) chromophores have been studied using optical absorption, cyclic voltammetry, photoluminescence quenching, X-ray diffraction, atomic force microscopy, and current-voltage measurements. The results provided useful insights into the use of DPP and PDI based molecules as donor-acceptor composites for organic photovoltaic (OPV) applications. Beside optoelectronic compatibility, the choice of active layer processing conditions is of key importance to improve the performance of BHJ solar cells. In this context, post-production treatments, viz. thermal and solvent vapour annealing, and the use of 1,8-diiodooctane as a solvent additive were employed to optimize the morphology of blend films. X-ray diffraction and atomic force microscopy indicated that the aforementioned processing strategies led to non-optimal composite morphologies with significantly large crystallites in comparison to exciton diffusion lengths. Although the open circuit voltage of the OPV devices was satisfactory (0.78 V), it was anticipated that the bulky domains hamper charge dissociation and transport, which resulted in low photovoltaic performance.

Design and synthesis of molecular donors for solution-processed high-efficiency organic solar cells.

Organic semiconductors incorporated into solar cells using a bulk heterojunction (BHJ) construction show promise as a cleaner answer to increasing energy needs throughout the world. Organic solar cells based on the BHJ architecture have steadily increased in their device performance over the past two decades, with power conversion efficiencies reaching 10%. Much of this success has come with conjugated polymer/fullerene combinations, where optimized polymer design strategies, synthetic protocols, device fabrication procedures, and characterization methods have provided significant advancements in the technology. More recently, chemists have been paying particular attention to well-defined molecular donor systems due to their ease of functionalization, amenability to standard organic purification and characterization methods, and reduced batch-to-batch variability compared to polymer counterparts. There are several critical properties for efficient small molecule donors. First, broad optical absorption needs to extend towards the near-IR region to achieve spectral overlap with the solar spectrum. Second, the low lying highest occupied molecular orbital (HOMO) energy levels need to be between -5.2 and -5.5 eV to ensure acceptable device open circuit voltages. Third, the structures need to be relatively planar to ensure close intermolecular contacts and high charge carrier mobilities. And last, the small molecule donors need to be sufficiently soluble in organic solvents (≥10 mg/mL) to facilitate solution deposition of thin films of appropriate uniformity and thickness. Ideally, these molecules should be constructed from cost-effective, sustainable building blocks using established, high yielding reactions in as few steps as possible. The structures should also be easy to functionalize to maximize tunability for desired properties. In this Account, we present a chronological description of our thought process and design strategies used in the development of highly efficient molecular donors that achieve power conversion efficiencies greater than 7%. The molecules are based on a modular D(1)-A-D(2)-A-D(1) architecture, where A is an asymmetric electron deficient heterocycle, which allowed us to quickly access a library of compounds and develop structure-property-performance relationships. Modifications to the D1 and D2 units enable spectral coverage throughout the entire visible region and control of HOMO energy levels, while adjustments to the pendant alkyl substituents dictate molecular solubility, thermal transition temperatures, and solid-state organizational tendencies. Additionally, we discuss regiochemical considerations that highlight how individual atom placements can significantly influence molecular and subsequently device characteristics. Our results demonstrate the utility of this architecture for generating promising materials to be integrated into organic photovoltaic devices, call attention to areas for improvement, and provide guiding principles to sustain the steady increases necessary to move this technology forward.

An electron-deficient small molecule accessible from sustainable synthesis and building blocks for use as a fullerene alternative in organic photovoltaics.

An electron-deficient small molecule accessible from sustainable isoindigo and phthalimide building blocks was synthesized via optimized synthetic procedures that incorporate microwave-assisted synthesis and a heterogeneous catalyst for Suzuki coupling, and direct heteroarylation carbon-carbon bond forming reactions. The material was designed as a non-fullerene acceptor with the help of DFT calculations and characterized by optical, electronic, and thermal analysis. Further investigation of the material revealed a differing solid-state morphology with the use of three well-known processing conditions: thermal annealing, solvent vapor annealing and small volume fractions of 1,8-diiodooctane (DIO) additive. These unique morphologies persist in the active layer blends and have demonstrated a distinct influence on device performance. Organic photovoltaic-bulk heterojunction (OPV-BHJ) devices show an inherently high open circuit voltage (Voc ) with the best power conversion efficiency (PCE) cells reaching 1.0 V with 0.4 v/v % DIO as a processing additive.

Design and computational characterization of non-fullerene acceptors for use in solution-processable solar cells.

In an effort to seek high-performance small molecule electron acceptor materials for use in heterojunction solar cells, computational chemistry was used to examine a variety of terminal acceptor-conjugated bridge-core acceptor-conjugated bridge-terminal acceptor small molecules. In particular, we have systematically predicted the geometric, electronic, and optical properties of 16 potential small-molecule acceptors based upon a series of electron deficient π-conjugated building blocks that have been incorporated into materials exhibiting good electron transport properties. Results show that the band gap, HOMO/LUMO energy levels, orbital spatial distribution, and intrinsic dipole moments can be systematically altered by varying the electron properties of the terminal or core acceptor units. In addition, the identity of the conjugated bridge can help fine-tune the electronic properties of the molecule, where this study showed that the strongest electron affinity of the conjugated π-bridge increased the stability in the HOMO and LUMO energies and increased the band gap of these small-molecule acceptors. As a result, this work points toward an isoindigo (C5) core combined with C2-thienopyrrole dione (A5) terminal units as the most promising small molecule acceptor material that can be fine-tuned with the choice of conjugated bridge and may be considered as reasonable candidates for synthesis and incorporation into organic solar cells.

Impact of regiochemistry and isoelectronic bridgehead substitution on the molecular shape and bulk organization of narrow bandgap chromophores.

A comparison of two classes of small molecules relevant to the field of organic electronics is carried out at the molecular and supramolecular levels. First, two molecules that differ only in the position of a pyridyl N-atom within an acceptor fragment are compared and contrasted. X-ray investigation of single crystals reveals that positioning the pyridyl N-atoms proximal to the molecules center changes the molecular shape by bending the molecule into a banana shape. Second, we demonstrate that the banana shape of the molecule can be controlled by replacing a Si atom within the dithienosilole fragment with a C or Ge atom. Here, utilization of cyclopentadithiophene or dithienogermole as the internal electron-rich unit leads to a decrease or an increase in the bending of the conjugated backbone, respectively. Such molecular shape changes alter intermolecular packing and thus affect bulk properties, leading to large differences in the optical, thermal, and crystallization properties.

Pyridalthiadiazole-based narrow band gap chromophores.

π-Conjugated materials containing pyridal[2,1,3]thiadiazole (PT) units have recently achieved record power conversion efficiencies of 6.7% in solution-processed, molecular bulk-heterojunction (BHJ) organic photovoltaics. Recognizing the importance of this new class of molecular systems and with the aim of establishing a more concrete path forward to predict improvements in desirable solid-state properties, we set out to systematically alter the molecular framework and evaluate structure-property relationships. Thus, the synthesis and properties of 13 structurally related D(1)-PT-D(2)-PT-D(1) compounds, where D represents a relatively electron-rich aromatic segment compared to PT, are provided. Physical properties were examined using a combination of absorption spectroscopy, cyclic voltammetry, thermal gravimetric analysis, differential scanning calorimetry, and solubility analysis. Changes to end-capping D(1) units allowed for fine control over electronic energy levels both in solution and in the bulk. Substitution of different alkyl chains on D(2) gives rise to controllable melting and crystallization temperatures and tailored solubility. Alterations to the core donor D(2) lead to readily identifiable changes in all properties studied. Finally, the regiochemistry of the pyridal N-atom in the PT heterocycle was investigated. The tailoring of structures via subtle structural modifications in the presented molecular series highlights the simplicity of accessing this chromophore architecture. Examination of the resulting materials properties relevant for device fabrication sets forth which can be readily predicted by consideration of molecular structure and which lack a systematic understanding. Guidelines can be proposed for the design of new molecular frameworks with the possibility of outperforming the current state of the art OPV performance.

Solar cell efficiency, self-assembly, and dipole-dipole interactions of isomorphic narrow-band-gap molecules.

We examine the correlations of the dipole moment and conformational stability to the self-assembly and solar cell performance within a series of isomorphic, solution-processable molecules. These charge-transfer chromophores are described by a D(1)-A-D-A-D(1) structure comprising electron-rich 2-hexylbithiophene and 3,3'-di-2-ethylhexylsilylene-2,2'-bithiophene moieties as the donor units D(1) and D, respectively. The building blocks 2,1,3-benzothiadiazole (BT) and [1,2,5]thiadiazolo[3,4-c]pyridine (PT) were used as the electron-deficient acceptor units A. Using a combination of UV-visible spectroscopy, field-effect transistors, solar cell devices, grazing incident wide-angle X-ray scattering, and transmission electron microscopy, three PT-containing compounds (1-3) with varying regiochemistry and symmetry, together with the BT-based compound 5,5'-bis{(4-(7-hexylthiophen-2-yl)thiophen-2-yl)-[1,2,5]thiadiazolobenzene}-3,3'-di-2-ethylhexylsilylene-2,2'-bithiophene (4), are compared and contrasted in solution, in thin films, and as blends with the electron acceptor [6,6]-phenyl-C(70)-butyric acid methyl ester. The molecules with symmetric orientations of the PT acceptor, 1 and 2, yield highly ordered blended thin films. The best films, processed with the solvent additive 1,8-diiodooctane, show donor "crystallite" length scales on the order of 15-35 nm and photovoltaic power conversion efficiencies (PCEs) of 7.0 and 5.6%, respectively. Compound 3, with an unsymmetrical orientation of PT heterocycles, shows subtle differences in the crystallization behavior and a best PCE of 3.2%. In contrast, blends of the BT-containing donor 4 are highly disordered and give PCEs below 0.2%. We speculate that the differences in self-assembly arise from the strong influence of the BT acceptor and its orientation on the net dipole moment and geometric description of the chromophore.

Photoinduced charge generation in a molecular bulk heterojunction material.

Understanding the charge generation dynamics in organic photovoltaic bulk heterojunction (BHJ) blends is important for providing the necessary guidelines to improve overall device efficiency. Despite more than 15 years of experimental and theoretical studies, a universal picture describing the generation and recombination processes operating in organic photovoltaic devices is still being forged. We report here the results of ultrafast transient absorption spectroscopy measurements of charge photogeneration and recombination processes in a high-performing solution-processed molecular BHJ. For comparison, we also studied a high-performing polymer-based BHJ material. We find that the majority of charge carriers in both systems are generated on <100 fs time scales and posit that excited state delocalization is responsible for the ultrafast charge transfer. This initial delocalization is consistent with the fundamental uncertainty associated with the photon absorption process (in the visible, λ/4π > 30 nm) and is comparable with the phase-separated domain size. In addition, exciton diffusion to charge-separating heterojunctions is observed at longer times (1-500 ps). Finally, charge generation in pure films of the solution processed molecule was studied. Polarization anisotropy measurements clearly demonstrate that the optical properties are dominated by molecular (Frenkel) exictons and delocalized charges are promptly produced (t < 100 fs).

Solution-processed small-molecule solar cells with 6.7% efficiency.

Organic photovoltaic devices that can be fabricated by simple processing techniques are under intense investigation in academic and industrial laboratories because of their potential to enable mass production of flexible and cost-effective devices. Most of the attention has been focused on solution-processed polymer bulk-heterojunction (BHJ) solar cells. A combination of polymer design, morphology control, structural insight and device engineering has led to power conversion efficiencies (PCEs) reaching the 6-8% range for conjugated polymer/fullerene blends. Solution-processed small-molecule BHJ (SM BHJ) solar cells have received less attention, and their efficiencies have remained below those of their polymeric counterparts. Here, we report efficient solution-processed SM BHJ solar cells based on a new molecular donor, DTS(PTTh(2))(2). A record PCE of 6.7% under AM 1.5 G irradiation (100 mW cm(-2)) is achieved for small-molecule BHJ devices from DTS(PTTh(2))(2):PC(70)BM (donor to acceptor ratio of 7:3). This high efficiency was obtained by using remarkably small percentages of solvent additive (0.25% v/v of 1,8-diiodooctane, DIO) during the film-forming process, which leads to reduced domain sizes in the BHJ layer. These results provide important progress for solution-processed organic photovoltaics and demonstrate that solar cells fabricated from small donor molecules can compete with their polymeric counterparts.

Ni, Pd, Pt, and Ru complexes of phosphine-borate ligands.

The species Cy(2)PHC(6)F(4)BF(C(6)F(5))(2) reacts with Pt(PPh(3))(4) to yield the new product cis-(PPh(3))(2)PtH(Cy(2)PC(6)F(4)BF(C(6)F(5))(2)) 1 via oxidative addition of the P-H bond of the phosphonium borate to Pt(0). The corresponding reaction with Pd(PPh(3))(4) affords the Pd analogue of 1, namely, cis-(PPh(3))(2)PdH(Cy(2)PC(6)F(4)BF(C(6)F(5))(2)) 3; while modification of the phosphonium borate gave the salt [(PPh(3))(3)PtH][(tBu(2)PC(6)F(4)BF(C(6)F(5))(2))] 2. Alternatively initial deprotonation of the phosphonium borate gave [tBu(3)PH][Cy(2)PC(6)F(4)BF(C(6)F(5))(2)] 4, [SIMesH][Cy(2)PC(6)F(4)BF(C(6)F(5))(2)] 5 which reacted with NiCl(2)(DME) yielding [BaseH](2)[trans-Cl(2)Ni(Cy(2)PC(6)F(4)BF(C(6)F(5))(2))(2)] (Base = tBu(3)P 6, SIMes 7) or with PdCl(2)(PhCN)(2) to give [BaseH](2)[trans-Cl(2)Pd(Cy(2)PC(6)F(4)BF(C(6)F(5))(2))(2)] (Base = tBu(3)P 8, SIMes 9). While [C(10)H(6)N(2)(Me)(4)H][tBu(2)PC(6)F(4)BF(C(6)F(5))(2)] 10 was also prepared. A third strategy for formation of a metal complex of anionic phosphine-borate derivatives was demonstrated in the reaction of (COD)PtMe(2) with the neutral phosphine-borane Mes(2)PC(6)F(4)B(C(6)F(5))(2) affording (COD)PtMe(Mes(2)PC(6)F(4)BMe(C(6)F(5))(2)) 11. Extension of this reactivity to tBu(2)PH(CH(2))(4)OB(C(6)F(5))(3)) was demonstrated in the reaction with Pt(PPh(3))(4) which yielded cis-(PPh(3))(2)PtH(tBu(2)P(CH(2))(4)OB(C(6)F(5))(3)) 12, while the reaction of [SIMesH][tBu(2)P(CH(2))(4)OB(C(6)F(5))(3)] 13 with NiCl(2)(DME) and PdCl(2)(PhCN)(2) afforded the complexes [SIMesH](2)[trans-Cl(2)Ni(tBu(2)PC(4)H(8)OB(C(6)F(5))(3))(2)] 14 and [SIMesH](2)[trans-PdCl(2)(tBu(2)P(CH(2))(4)OB(C(6)F(5))(3))(2)] 15, respectively, analogous to those prepared with 4 and 5. Finally, the reaction of 7 and 13with [(p-cymene)RuCl(2)](2) proceeds to give the new orange products [SIMesH][(p-cymene)RuCl(2)(Cy(2)PC(6)F(4)BF(C(6)F(5))(2))] 16 and [SIMesH][(p-cymene)RuCl(2)(tBu(2)P(CH(2))(4)OB(C(6)F(5))(3))] 17, respectively. Crystal structures of 1, 6, 10, 11, 12, and 16 are reported.

Promoting photocatalytic CO2 reduction through facile electronic modification of N-annulated perylene diimide rhenium bipyridine dyads.

The development of CO2 conversion catalysts has become paramount in the effort to close the carbon loop. Herein, we report the synthesis, characterization, and photocatalytic CO2 reduction performance for a series of N-annulated perylene diimide (NPDI) tethered Re(bpy) supramolecular dyads [Re(bpy-C2-NPDI-R)], where R = -H, -Br, -CN, -NO2, -OPh, -NH2, or pyrrolidine (-NR2). The optoelectronic properties of these Re(bpy-C2-NPDI-R) dyads were heavily influenced by the nature of the R-group, resulting in significant differences in photocatalytic CO2 reduction performance. Although some R-groups (i.e. -Br and -OPh) did not influence the performance of CO2 photocatalysis (relative to -H; TONco ∼60), the use of an electron-withdrawing -CN was found to completely deactivate the catalyst (TONco < 1) while the use of an electron-donating -NH2 improved CO2 photocatalysis four-fold (TONco = 234). Despite being the strongest EWG, the -NO2 derivative exhibited good photocatalytic CO2 reduction abilities (TONco = 137). Using a combination of CV and UV-vis-nIR SEC, it was elucidated that the -NO2 derivative undergoes an in situ transformation to -NH2 under reducing conditions, thereby generating a more active catalyst that would account for the unexpected activity. A photocatalytic CO2 mechanism was proposed for these Re(bpy-C2-NPDI-R) dyads (based on molecular orbital descriptions), where it is rationalized that the photoexcitation pathway, as well as the electronic driving-force for NPDI2- to Re(bpy) electron-transfer both significantly influence photocatalytic CO2 reduction. These results help provide rational design principles for the future development of related supramolecular dyads.