Improved algorithm of aerosol particle size distribution based on remote sensing data.

The optical parameters (extinction or backscatter coefficients) of multi-wavelength beams can be used for the retrieval of the aerosol particle size distribution (APSD). An improved algorithm for APSD and aerosol microphysical parameters (AMPs) is studied and discussed by using only multi-wavelength extinction coefficients data. The regularized algorithm and prior value are combined for the retrieval of APSD and AMPs. The regularization algorithm, based on minimum discrepancy principle and averaging procedure, is used for the retrieval of fine-mode APSD and an averaging procedure that can achieve stable outputs is proposed. The 1% averaging result near the minimum of the discrepancy is selected and verified. Based on the inversion results of fine mode from the regularization algorithm, the lognormal distribution with a prior value (model radius) is applied to reconstruct the coarse mode of APSDs through fitting the data. The comprehensive application of the regularization algorithm and averaging process improves the stability of the inversion in the fine mode, and the use of the prior value broadens the inversion radius range of APSD. The complex refractive index need not be assumed for this method. The inversion error for different types of aerosols is analyzed and studied. The reliability of the algorithm is tested and verified by many typical APSDs and the measured APSDs by particle size spectrometer in different pollution days. The algorithm sensitivity analysis is also provided and discussed. The algorithm can obtain reliable inversion of APSD and AMPs with large radius range.

Largely enhanced efficiency in ZnO nanowire/p-polymer hybridized inorganic/organic ultraviolet light-emitting diode by piezo-phototronic effect.

ZnO nanowire inorganic/organic hybrid ultraviolet (UV) light-emitting diodes (LEDs) have attracted considerable attention as they not only combine the high flexibility of polymers with the structural and chemical stability of inorganic nanostructures but also have a higher light extraction efficiency than thin film structures. However, up to date, the external quantum efficiency of UV LED based on ZnO nanostructures has been limited by a lack of efficient methods to achieve a balance between electron contributed current and hole contributed current that reduces the nonradiative recombination at interface. Here we demonstrate that the piezo-phototronic effect can largely enhance the efficiency of a hybridized inorganic/organic LED made of a ZnO nanowire/p-polymer structure, by trimming the electron current to match the hole current and increasing the localized hole density near the interface through a carrier channel created by piezoelectric polarization charges on the ZnO side. The external efficiency of the hybrid LED was enhanced by at least a factor of 2 after applying a proper strain, reaching 5.92%. This study offers a new concept for increasing organic LED efficiency and has a great potential for a wide variety of high-performance flexible optoelectronic devices.

Piezotronic effect in solution-grown p-type ZnO nanowires and films.

Investigating the piezotronic effect in p-type piezoelectric semiconductor is critical for developing a complete piezotronic theory and designing/fabricating novel piezotronic applications with more complex functionality. Using a low temperature solution method, we were able to produce ultralong (up to 60 µm in length) Sb doped p-type ZnO nanowires on both rigid and flexible substrates. For the p-type nanowire field effect transistor, the on/off ratio, threshold voltage, mobility, and carrier concentration of 0.2% Sb-doped sample are found to be 10(5), 2.1 V, 0.82 cm(2)·V(-1)·s(-1), and 2.6 × 10(17) cm(-3), respectively, and the corresponding values for 1% Sb doped samples are 10(4), 2.0 V, 1.24 cm(2)·V(-1)·s(-1), and 3.8 × 10(17) cm(-3). We further investigated the universality of piezotronic effect in the as-synthesized Sb-doped p-type ZnO NWs and reported for the first time strain-gated piezotronic transistors as well as piezopotential-driven mechanical energy harvesting based on solution-grown p-type ZnO NWs. The results presented here broaden the scope of piezotronics and extend the framework for its potential applications in electronics, optoelectronics, smart MEMS/NEMS, and human-machine interfacing.

Eardrum-inspired active sensors for self-powered cardiovascular system characterization and throat-attached anti-interference voice recognition.

The first bionic membrane sensor based on triboelectrification is reported for self-powered physiological and behavioral measurements such as local internal body pressures for non-invasive human health assessment. The sensor can also be for self-powered anti-interference throat voice recording and recognition, as well as high-accuracy multimodal biometric authentication, thus potentially expanding the scope of applications in self-powered wearable medical/health monitoring, interactive input/control devices as well as accurate, reliable, and less intrusive biometric authentication systems.

Paper-based origami triboelectric nanogenerators and self-powered pressure sensors.

Discovering renewable and sustainable power sources is indispensable for the development of green electronics and sensor networks. In this paper, we present origami triboelectric nanogenerators (TENGs) using paper as the starting material, with a high degree of flexibility, light weight, low cost, and recyclability. Slinky- and doodlebug-shaped TENGs can be easily fabricated by properly folding printer papers. The as-fabricated TENGs are capable of harvesting ambient mechanical energy from various kinds of human motions, such as stretching, lifting, and twisting. The generated electric outputs have been used to directly light-up commercial LEDs. In addition, the as-fabricated TENGs can also serve as self-powered pressure sensors.

Harvesting broadband kinetic impact energy from mechanical triggering/vibration and water waves.

We invented a triboelectric nanogenerator (TENG) that is based on a wavy-structured Cu-Kapton-Cu film sandwiched between two flat nanostructured PTFE films for harvesting energy due to mechanical vibration/impacting/compressing using the triboelectrification effect. This structure design allows the TENG to be self-restorable after impact without the use of extra springs and converts direct impact into lateral sliding, which is proved to be a much more efficient friction mode for energy harvesting. The working mechanism has been elaborated using the capacitor model and finite-element simulation. Vibrational energy from 5 to 500 Hz has been harvested, and the generator's resonance frequency was determined to be ∼100 Hz at a broad full width at half-maximum of over 100 Hz, producing an open-circuit voltage of up to 72 V, a short-circuit current of up to 32 µA, and a peak power density of 0.4 W/m(2). Most importantly, the wavy structure of the TENG can be easily packaged for harvesting the impact energy from water waves, clearly establishing the principle for ocean wave energy harvesting. Considering the advantages of TENGs, such as cost-effectiveness, light weight, and easy scalability, this approach might open the possibility for obtaining green and sustainable energy from the ocean using nanostructured materials. Lastly, different ways of agitating water were studied to trigger the packaged TENG. By analyzing the output signals and their corresponding fast Fourier transform spectra, three ways of agitation were evidently distinguished from each other, demonstrating the potential of the TENG for hydrological analysis.

Optimizing performance of silicon-based p-n junction photodetectors by the piezo-phototronic effect.

Silicon-based p-n junction photodetectors (PDs) play an essential role in optoelectronic applications for photosensing due to their outstanding compatibility with well-developed integrated circuit technology. The piezo-phototronic effect, a three-way coupling effect among semiconductor properties, piezoelectric polarizations, and photon excitation, has been demonstrated as an effective approach to tune/modulate the generation, separation, and recombination of photogenerated electron-hole pairs during optoelectronic processes in piezoelectric-semiconductor materials. Here, we utilize the strain-induced piezo-polarization charges in a piezoelectric n-ZnO layer to modulate the optoelectronic process initiated in a p-Si layer and thus optimize the performances of p-Si/ZnO NWs hybridized photodetectors for visible sensing via tuning the transport property of charge carriers across the Si/ZnO heterojunction interface. The maximum photoresponsivity R of 7.1 A/W and fastest rising time of 101 ms were obtained from these PDs when applying an external compressive strain of -0.10‰ on the ZnO NWs, corresponding to relative enhancement of 177% in R and shortening to 87% in response time, respectively. These results indicate a promising method to enhance/optimize the performances of non-piezoelectric semiconductor material (e.g., Si) based optoelectronic devices by the piezo-phototronic effect.

3D fiber-based hybrid nanogenerator for energy harvesting and as a self-powered pressure sensor.

In the past years, scientists have shown that development of a power suit is no longer a dream by integrating the piezoelectric nanogenerator (PENG) or triboelectric nanogenerator (TENG) with commercial carbon fiber cloth. However, there is still no design applying those two kinds of NG together to collect the mechanical energy more efficiently. In this paper, we demonstrate a fiber-based hybrid nanogenerator (FBHNG) composed of TENG and PENG to collect the mechanical energy in the environment. The FBHNG is three-dimensional and can harvest the energy from all directions. The TENG is positioned in the core and covered with PENG as a coaxial core/shell structure. The PENG design here not only enhances the collection efficiency of mechanical energy by a single carbon fiber but also generates electric output when the TENG is not working. We also show the potential that the FBHNG can be weaved into a smart cloth to harvest the mechanical energy from human motions and act as a self-powered strain sensor. The instantaneous output power density of TENG and PENG can achieve 42.6 and 10.2 mW/m(2), respectively. And the rectified output of FBHNG has been applied to charge the commercial capacitor and drive light-emitting diodes, which are also designed as a self-powered alert system.

Triboelectrification based motion sensor for human-machine interfacing.

We present triboelectrification based, flexible, reusable, and skin-friendly dry biopotential electrode arrays as motion sensors for tracking muscle motion and human-machine interfacing (HMI). The independently addressable, self-powered sensor arrays have been utilized to record the electric output signals as a mapping figure to accurately identify the degrees of freedom as well as directions and magnitude of muscle motions. A fast Fourier transform (FFT) technique was employed to analyse the frequency spectra of the obtained electric signals and thus to determine the motion angular velocities. Moreover, the motion sensor arrays produced a short-circuit current density up to 10.71 mA/m(2), and an open-circuit voltage as high as 42.6 V with a remarkable signal-to-noise ratio up to 1000, which enables the devices as sensors to accurately record and transform the motions of the human joints, such as elbow, knee, heel, and even fingers, and thus renders it a superior and unique invention in the field of HMI.

Taxel-addressable matrix of vertical-nanowire piezotronic transistors for active and adaptive tactile imaging.

Designing, fabricating, and integrating arrays of nanodevices into a functional system are the key to transferring nanoscale science into applicable nanotechnology. We report large-array three-dimensional (3D) circuitry integration of piezotronic transistors based on vertical zinc oxide nanowires as an active taxel-addressable pressure/force sensor matrix for tactile imaging. Using the piezoelectric polarization charges created at a metal-semiconductor interface under strain to gate/modulate the transport process of local charge carriers, we designed independently addressable two-terminal transistor arrays, which convert mechanical stimuli applied to the devices into local electronic controlling signals. The device matrix can achieve shape-adaptive high-resolution tactile imaging and self-powered, multidimensional active sensing. The 3D piezotronic transistor array may have applications in human-electronics interfacing, smart skin, and micro- and nanoelectromechanical systems.

Piezotronic effect in flexible thin-film based devices.

Flexible piezotronic devices based on RF-sputtered piezoelectric semiconductor thin films have been investigated for the first time. The dominating role of the piezotronic effect over the geometrical and piezoresistive effect in the as-fabricated devices has been confirmed and the modulation effect of the piezopotential on charge carrier transport under different strains is subsequently studied. Moreover, it is also demonstrated that the UV sensing capability of the as-fabricated thin film based piezotronic device can be tuned by the piezopotential, showing significantly enhanced sensitivity and improved reset time under tensile strain.

Triboelectric active sensor array for self-powered static and dynamic pressure detection and tactile imaging.

We report an innovative, large-area, and self-powered pressure mapping approach based on the triboelectric effect, which converts the mechanical stimuli into electrical output signals. The working mechanism of the triboelectric active sensor (TEAS) was theoretically studied by both analytical method and numerical calculation to gain an intuitive understanding of the relationship between the applied pressure and the responsive signals. Relying on the unique pressure response characteristics of the open-circuit voltage and short-circuit current, we realize both static and dynamic pressure sensing on a single device for the first time. A series of comprehensive investigations were carried out to characterize the performance of the TEAS, and high sensitivity (0.31 kPa(-1)), ultrafast response time (<5 ms), long-term stability (30,000 cycles), as well as low detection limit (2.1 Pa) were achieved. The pressure measurement range of the TEAS was adjustable, which means both gentle pressure detection and large-scale pressure sensing were enabled. Through integrating multiple TEAS units into a sensor array, the as-fabricated TEAS matrix was capable of monitoring and mapping the local pressure distribution applied on the device with distinguishable spatial profiles. This work presents a technique for tactile imaging and progress toward practical applications of nanogenerators, providing potential solutions for accomplishment of artificial skin, human-electronic interfacing, and self-powered systems.

Enhanced performance of flexible ZnO nanowire based room-temperature oxygen sensors by piezotronic effect.

A flexible oxygen sensor based on individual ZnO nanowires is demonstrated with high sensitivity at room temperature and the influence of the piezotronic effect on the performance of this oxygen sensor is investigated. By applying a tensile strain, the already very high sensitivity due to the Schottky contact and pre-treatment of UV light is even further enhanced.

Single-electrode-based sliding triboelectric nanogenerator for self-powered displacement vector sensor system.

We report a single-electrode-based sliding-mode triboelectric nanogenerator (TENG) that not only can harvest mechanical energy but also is a self-powered displacement vector sensor system for touching pad technology. By utilizing the relative sliding between an electrodeless polytetrafluoroethylene (PTFE) patch with surface-etched nanoparticles and an Al electrode that is grounded, the fabricated TENG can produce an open-circuit voltage up to 1100 V, a short-circuit current density of 6 mA/m(2), and a maximum power density of 350 mW/m(2) on a load of 100 MΩ, which can be used to instantaneously drive 100 green-light-emitting diodes (LEDs). The working mechanism of the TENG is based on the charge transfer between the Al electrode and the ground by modulating the relative sliding distance between the tribo-charged PTFE patch and the Al plate. Grating of linear rows on the Al electrode enables the detection of the sliding speed of the PTFE patch along one direction. Moreover, we demonstrated that 16 Al electrode channels arranged along four directions were used to monitor the displacement (the direction and the location) of the PTFE patch at the center, where the output voltage signals in the 16 channels were recorded in real-time to form a mapping figure. The advantage of this design is that it only requires the bottom Al electrode to be grounded and the top PTFE patch needs no electrical contact, which is beneficial for energy harvesting in automobile rotation mode and touch pad applications.

Triboelectric nanogenerator for harvesting wind energy and as self-powered wind vector sensor system.

We report a triboelectric nanogenerator (TENG) that plays dual roles as a sustainable power source by harvesting wind energy and as a self-powered wind vector sensor system for wind speed and direction detection. By utilizing the wind-induced resonance vibration of a fluorinated ethylene-propylene film between two aluminum foils, the integrated TENGs with dimensions of 2.5 cm × 2.5 cm × 22 cm deliver an output voltage up to 100 V, an output current of 1.6 µA, and a corresponding output power of 0.16 mW under an external load of 100 MΩ, which can be used to directly light up tens of commercial light-emitting diodes. Furthermore, a self-powered wind vector sensor system has been developed based on the rationally designed TENGs, which is capable of detecting the wind direction and speed with a sensitivity of 0.09 µA/(m/s). This work greatly expands the applicability of TENGs as power sources for self-sustained electronics and also self-powered sensor systems for ambient wind detection.

High-performance single CdS nanowire (nanobelt) Schottky junction solar cells with Au/graphene Schottky electrodes.

High-performance single CdS nanowire (NW) as well as nanobelt (NB) Schottky junction solar cells were fabricated. Au (5 nm)/graphene combined layers were used as the Schottky contact electrodes to the NWs (NBs). Typical as-fabricated NW solar cell shows excellent photovoltaic behavior with an open circuit voltage of ∼0.15 V, a short circuit current of ∼275.0 pA, and an energy conversion efficiency of up to ∼1.65%. The physical mechanism of the combined Schottky electrode was discussed. We attribute the prominent capability of the devices to the high-performance Schottky combined electrode, which has the merits of low series resistance, high transparency, and good Schottky contact to the CdS NW (NB). Besides, a promising site-controllable patterned graphene transfer method, which has the advantages of economizing graphene material and free from additional etching process, was demonstrated in this work. Our results suggest that semiconductor NWs (NBs) are promising materials for novel solar cells, which have potential application in integrated nano-optoelectronic systems.

Ultrahigh-performance inverters based on CdS nanobelts.

We report ultrahigh-performance inverters, each consisting of two top-gate metal-oxide-semiconductor field-effect transistors based on n-CdS nanobelts. High-kappa HfO(2) dielectrics are used as the top-gate oxide layers. The inverters have a large supply voltage (V(DD)) range (from 50 mV to 10 V) and very high voltage gain ( approximately 10, 100, and 1000 at V(DD) = 0.2, 1, and 10 V, respectively). Current consumption is less than 7 nA at V(DD) = 1 V, corresponding to a power consumption of less than 7 nW. The high and low output voltages are close to full rail. The inverters also exhibit good dynamic behavior with square wave input at frequencies up to 1 kHz. The operation of the inverters is analyzed in detail. The inverters are promising for future low power high performance logic circuit applications.