All-Dielectric Integrated Meta-Antenna Operating in 6G Terahertz Communication Window.

Efficient transceivers and antennas at terahertz frequencies are leading the development of 6G terahertz communication systems. The antenna design for high-resolution terahertz spatial sensing and communication remains challenging, while emergent metallic metasurface antennas can address this issue but often suffer from low efficiency and complex manufacturing. Here, an all-dielectric integrated meta-antenna operating in 6G terahertz communication window for high-efficiency beam focusing in the sub-wavelength scale is reported. With the antenna surface functionalized by metagrating arrays with asymmetric scattering patterns, the design and optimization methods are demonstrated with a physical size constraint. The highest manipulation and diffraction efficiencies achieve 84.1% and 48.1%. The commercially accessible fabrication method with low cost and easy to implement has been demonstrated for the meta-antenna by photocuring 3D printing. A filamentous focal spot is measured as 0.86λ with a long depth of focus of 25.3λ. Its application for integrated imaging and communication has been demonstrated. The proposed technical roadmap provides a general pathway for creating high-efficiency integrated meta-antennas with great potential in high-resolution 6G terahertz spatial sensing and communication applications.

Investigation of unidirectional coupling of dipole emitters in valley photonic heterostructure waveguides.

Photonic heterostructure has recently become a promising platform to study topological photonics with the introduction of mode width degree of freedom (DOF). However, there is still a lack of comprehensive analysis on the coupling of dipole emitters in photonic heterostructures, which constrains the development of on-chip quantum optics based on chiral dipole sources. We systematically analyze the unidirectional coupling mechanism between dipole emitters and valley photonic heterostructure waveguides (VPHWs). With the eigenmode calculations and full-wave simulations, the Stokes parameters are obtained to compare the coupling performance of two types of valley-interface VPHWs. Simulation results show that compared to the zigzag interface with inversion symmetry, the strategy of bearded interface with glide symmetry is easier to realize high-efficiency coupling. By adjusting the position and chirality of dipole emitters in VPHWs, the transmission of light reverses with guided modes coupled to different directions. Furthermore, a topological beam modulator is realized based on VPHWs, which maintains the robustness to large-area potential barriers and sharp corners. Our work supplies a powerful guide for chiral light-matter interaction, which is expected to be applied to increasingly compact and efficient on-chip optical platforms in the future.

Tunable metasurfaces for implementing terahertz controllable NOT logic gate functions.

Compared with traditional electrical logic gates, optical or terahertz (THz) computing logic gates have faster computing speeds and lower power consumption, and can better meet the huge data computing needs. However, there are limitations inherent in existing optical logic gates, such as single input/output channels and susceptibility to interference. Here, we proposed a new approach utilizing polarization-sensitive graphene-vanadium dioxide metasurface THz logic gates. Benefitting from two actively tunable materials, the proposed controlled-NOT logic gate(CNOT LG) enables versatile functionality through a dual-parameter control system. This system allows for the realization of multiple output states under diverse polarized illuminating conditions, aligning with the expected input-output logic relationship of the CNOT LG. Furthermore, to demonstrate the robustness of the designed THz CNOT LG metasurface, we designed an imaging array harnessing the dynamic control capabilities of tunable meta-atoms, facilitating clear near-field imaging. This research is promising for advancing CNOT LG applications in the THz spectrum. It has potential applications in telecommunications, sensing, and imaging.

Wavelength division multiplexing based on the coupling effect of helical edge states in two-dimensional dielectric photonic crystals.

Photonic topological insulators with topologically protected edge states featuring one-way, robustness and backscattering-immunity possess extraordinary abilities to steer and manipulate light. In this work, we construct a topological heterostructure (TH) consisting of a domain of nontrivial pseudospin-type topological photonic crystals (PCs) sandwiched between two domains of trivial PCs based on two-dimensional all-dielectric core-shell PCs in triangle lattice. We consider three THs with different number of layers in the middle nontrivial domain (i.e., one-layer, two-layer, three-layer) and demonstrate that the projected band diagrams of the three THs host interesting topological waveguide states (TWSs) with properties of one-way, large-area, broad-bandwidth and robustness due to coupling effect of the helical edge states associated with the two domain-wall interfaces. Moreover, taking advantage of the tunable bandgap between the TWSs by the layer number of the middle domain due to the coupling effect, a topological Y-splitter with functionality of wavelength division multiplexing is explicitly demonstrated exploiting the unique feature of the dispersion curves of TWSs in the three THs. Our work not only offers a new method to realize pseudospin-polarized large-area TWSs with tunable mode-width, but also could provide new opportunities for practical applications in on-chip multifunctional (i.e., wavelength division multiplexing) photonic devices with topological protection and information processing with pseudospin-dependent transport.

Nd:YVO4/YVO4 cascaded Raman laser pumped dual-wavelength signal wave MgO:PPLN-OPO with wide range adjustable wavelength interval.

This article presents a dual-wavelength signal wave output system capable of generating a broad range of adjustable wavelength intervals. The setup involved the creation of a dual-wavelength cascaded Raman laser featuring composite cavities operating at 1176 nm and 1313 nm. Experimental investigations were carried out on an external cavity MgO:PPLN-OPO driven by the cascaded Raman laser. By setting the crystal polarization period to 27.6-34.4 µm and the temperature to 50-130°C, adjustable tunable output of dual-wavelength signal wave at 1176 nm-MgO:PPLN-OPO (1550-2294 nm) and 1313 nm-MgO:PPLN-OPO (1768-2189 nm) was achieved with a wavelength interval of 0-218 nm. Under the conditions of a period of 34.4 µm, temperature of 90°C, and an incident Raman power of 2.6 W, the highest conversion efficiency of Raman to dual-wavelength signal wave (2212, 2182 nm) was 34.2%. Furthermore, the maximum output power of dual-wavelength signal wave was recorded at 1.02 W with an incident Raman power of 3.33 W.

High responsivity photodetector based on MEH-PPV/CsPbBr3heterojunction.

Perovskite quantum dots (QDs) and organic materials have great research potential in the field of optoelectronic devices. In this paper, MEH-PPV/CsPbBr3heterojunction photodetectors (PDs) are prepared by spin coating method based on the good photoelectric properties of CsPbBr3perovskite QDs and MEH-PPV. The MEH-PPV/CsPbBr3heterojunction improves the energy level arrangement, and CsPbBr3QDs can passivate the surface defects of MEH-PPV films to achieve effective charge separation and transfer, thus inhibiting the dark current and improving the photoelectric performance of the device. Under 532 nm laser irradiation, the responsivity (R) of MEH-PPV/CsPbBr3heterojunction PD is 11.98 A W-1, the specific detectivity (D*) is 6.98 × 1011Jones, and the response time is 15/16 ms. This work provides experience for the study of perovskite QDs and organic materials heterojunction optoelectronic devices.

MAPbI3perovskite photodetectors for high-performance optical wireless communication.

High-sensitivity and fast-response photodetectors (PDs) are vital part of optical wireless communication (OWC) system. In this work, we develop an organic-inorganic hybrid perovskite material (MAPbI3) based p-i-n structured PD. By optimizing the precursor solution concertation, the PD showed a high responsivity of 0.98 A W-1, a fast response timetrise/tfallof 12/12.5 µs, a specific detectivity of 2.62 × 1013Jones, and the f-3dBof 24 kHz under the 532 nm laser and -0.2 V bias voltage. Furthermore, we designed an OWC system based on the prepared PD. With the baud rate of 19200 bps, the system exhibits a bit error rate less than 10-6, and it can realize 9.63 m long-distance communication and quick transmission applications such as strings, texts, photos, and audios. Our work demonstrates the great application potential of perovskite PDs in the field of optical communication.

High performance CsBi3I10/PCBM bulk heterojunction perovskite photodetector.

Lead halide perovskites (LHPs) have been extensively studied due to their remarkable optoelectronic performance. However, the toxicity of a lead ion to humans and its instability under ambient conditions render lead-based halide perovskite an unsuitable material for commercialization. Meanwhile, lead-free halide perovskite (LFHP) devices generally exhibit poor performance. Therefore, enhancing photoelectric conversion capacity is the most important issue that needs to be addressed. Here, we propose a photodetector (PD) fabricated using C s B i 3 I 10/p h e n y l-C 61-butyric acid methyl ester (PCBM) bulk heterojunction as the active layer. The PD illuminated under 532 nm can reach a high responsivity (1.54 A/W) at -2V bias, while at 2 V bias, the PD reaches a higher responsivity (224.40 A/W). All of those results suggest that C s B i 3 I 10/P C B M bulk heterojunctions hold enormous potential in substituting for LHPs in optoelectronic devices.

The Highly Sensitive Refractive Index Sensing of Seawater Based on a Large Lateral Offset Mach-Zehnder Interferometer.

A novel fiber sensor for the refractive index sensing of seawater based on a Mach-Zehnder interferometer has been demonstrated. The sensor consisted of a single-mode fiber (SMF)-no-core fiber (NCF)-single-mode fiber structure (shortened to an SNS structure) with a large lateral offset spliced between the two sections of a multimode fiber (MMF). Optimization studies of the multimode fiber length, offset SNS length, and vertical axial offset distance were performed to improve the coupling efficiency of interference light and achieve the best extinction ratio. In the experiment, a large lateral offset sensor was prepared to detect the refractive index of various ratios of saltwater, which were used to simulate seawater environments. The sensor's sensitivity was up to -13,703.63 nm/RIU and -13,160 nm/RIU in the refractive index range of 1.3370 to 1.3410 based on the shift of the interference spectrum. Moreover, the sensor showed a good linear response and high stability, with an RSD of only 0.0089% for the trough of the interference in air over 1 h.

Narrow linewidth and wideband tunable continuous-wave terahertz generator based on difference frequency generation with DAST crystal.

A narrow linewidth and wideband tunable continuous-wave terahertz generator with DAST crystal has been demonstrated in this paper. Two narrow-linewidth CW fiber lasers were used as the pump sources for difference frequency generation. The terahertz wave can be continuously tunable in the range of 1.1-3 THz. The maximum output power of 2.79nW was obtained at 2.568 THz. The linewidth of the output THz wave was estimated to be 56.5 MHz by fitting transmission spectrum of CO gas at 450 Pa pressure around 80.52 cm-1 with the Vogit gas model. Furthermore, the output spectra at room temperature and pressure was in good agreement with the air absorption lines in Hitran database. Moreover, the narrower absorption characteristic spectrum of 2-Deoxy-D-Glucose sample has been obtained through the spectrum measurements. Therefore, it could promote the practical prospect of tunable CW-THz source, which will have good potential in THz high-precision spectroscopic detection and multispectral imaging.

Terahertz narrowband filter metasurfaces based on bound states in the continuum.

The electromagnetically induced transparency (EIT) effect realized by metasurfaces have potential for narrowband filtering due to their narrow bandwidth. In optics, bound states in the continuum (BIC) can produce strong localized resonances, which means that light can be trapped and stored for long periods of time to produce very high Q-factors. This has potential applications in designing highly efficient sensors and narrow bandpass filters. Here, we present two metal-flexible dielectric metasurfaces consisting of copper structures and polyimide substrates. Quasi BICs are obtained by breaking C2 symmetry of the metal structures. Resonance-captured quasi-BICs with ultra-high q-factor resonances satisfy the dark modes required to realize the EIT and couple to the bright modes in the structure to achieve narrowband filtering. The peak transmission rates are around 0.9 at 0.29 THz-0.32 THz and 0.23 THz-0.27 THz, respectively. Our results have practical implications for the realization of low-frequency terahertz communications.

Ultrasensitive optical modulation in hybrid metal-perovskite and metal-graphene metasurface THz devices.

Implementation of efficient terahertz (THz) wave control is essential for THz technology development for applications including sixth-generation communications and THz sensing. Therefore, realization of tunable THz devices with large-scale intensity modulation capabilities is highly desirable. By integrating perovskite and graphene with a metallic asymmetric metasurface, two ultrasensitive devices for dynamic THz wave manipulation through low-power optical excitation are demonstrated experimentally here. The perovskite-based hybrid metadevice offers ultrasensitive modulation with a maximum modulation depth for the transmission amplitude reaching 190.2% at the low optical pump power of 5.90 mW/cm2. Additionally, a maximum modulation depth of 227.11% is achieved in the graphene-based hybrid metadevice at a power density of 18.87 mW/cm2. This work paves the way toward design and development of ultrasensitive devices for optical modulation of THz waves.

Longitudinal evolution from scalar to vector beams assembled from all-dielectric metasurfaces.

Vector vortex beams (VVBs) with non-uniform polarization states have a wide range of applications, from particle capture to quantum information. Here, we theoretically demonstrate a generic design for all-dielectric metasurfaces operating in the terahertz (THz) band, characterized as a longitudinal evolution from scalar vortices carrying homogeneous polarization states to inhomogeneous vector vortices with polarization singularities. The order of the converted VVBs can be arbitrarily tailored by manipulating the topological charge embedded in two orthogonal circular polarization channels. The introduction of the extended focal length and the initial phase difference effectively guarantees the smoothness of the longitudinal switchable behavior. A generic design approach based on vector-generated metasurfaces can assist in the exploration of new singular properties of THz optical fields.

Efficient continuous-wave Nd:YVO4/KGW intracavity Raman laser.

We demonstrate an efficient Nd:YVO4/KGW intracavity Raman laser in continuous-wave (CW) scheme. With a V-shaped fundamental laser cavity and a short Stokes cavity in it, the oscillating beam sizes are designed to alleviate the thermal effect and to enhance the Raman gain for efficient CW operation. The output power of CW Stokes wave at 1177 nm reached 9.33 W under an incident laser diode pump power of 36.65 W, with corresponding optical efficiency being 25.5%. To the best of our knowledge, these are the highest Stokes output power and conversion efficiency of CW intracavity Raman lasers.

1.2†W single-frequency Tm3+/Ho3+ co-doped fiber oscillator at 2050†nm.

In this Letter, a watt-level single-frequency fiber oscillator at 2050 nm was demonstrated for the first time, to the best of our knowlegde, in a linear laser cavity with a piece of an un-pumped Tm3+/Ho3+ co-doped fiber serving as a saturable absorber. With delicate optimization of mode filtering effect of the dynamic gratings formed in the saturable absorber, a maximum single-frequency laser output power of 1.2 W was achieved under a total bidirectional pump power of 5.8 W at 1570 nm, and the corresponding optical efficiency is 20.7%. This is, to the best of our knowledge, the highest power of a single-frequency fiber oscillator at the wavelength above 2 µm.

Widely tunable single-frequency Er-doped ZBLAN fiber laser with emission from 3.37 to 3.72†µm.

We demonstrate a widely tunable single-frequency Er-doped ZBLAN fiber laser operating on a 4F9/2→4I9/2 transition band. An uncoated germanium (Ge) plate serves as a narrow-bandwidth etalon and is inserted in the cavity to achieve a single longitudinal mode selection. Wavelength tuning from 3373.8 nm to 3718.5 nm was demonstrated by using a blazed diffraction grating at 3.5 µm. At the emission peak of 3465.6 nm, the laser yields over 100 mW single-frequency output power, with a 3 dB linewidth <6.9 MHz, and a slope efficiency (with respect to the incident 1990 nm pump power) of 20.3%. Such a tunable mid-infrared single-frequency fiber laser may serve as a versatile laser source in spectroscopy and sensing applications.

High-power, high-efficiency single-frequency DBR fiber laser at 1064†nm based on Yb3+-doped silica fiber.

A high-power, high-efficiency single-frequency fiber laser at 1064 nm was demonstrated based on a distributed Bragg reflector (DBR) all-silica-fiber configuration. A single-frequency laser with an output power of 642 mW and slope efficiency of 66.4% with respect to absorbed pump power was achieved from a 1.2-cm-long commercially available Yb3+-doped silica fiber. To the best of our knowledge, this is the highest single-frequency laser power and efficiency obtained from the DBR all-silica fiber laser. The work presented here paves the way for the development of high-power, robust, and cost-effective single-frequency Yb3+-doped all-silica fiber lasers.

Terahertz beam characterization by temporal-spatial mapping with a reflecting echelon.

A terahertz beam imaging method was proposed that involves scanning a reflecting echelon with temporal-spatial mapping inversion based on self-developed translation-scan and rotation-scan temporal-spatial mapping (TTSM and RTSM) algorithms. The beam characteristics of a terahertz time-domain spectroscopy (TDS) system, such as its size, shape, and energy distribution, were obtained. Besides the weak terahertz beam emitted from a TDS system, this scheme is also suitable for imaging large-size terahertz or laser beams in time-domain systems where existing beam imaging is impractical.

Chiral metasurface zone plate for transmission-reflection focusing of circularly polarized terahertz waves.

The properties of traditional Fresnel zone plates have been greatly enhanced by metasurfaces, which allow the control of polarization, orbital angular momentum, or other parameters on the basis of focusing. In this Letter, a new, to the best of our knowledge, method for circularly polarized wave manipulation based on a zone plate is proposed. Chiral meta-atoms and binary geometric phase are used for the simultaneous focusing of reflected and transmitted terahertz waves. The silicon-based dielectric chiral units, which show great performance of spin-selective transmission near 0.54 THz, separate the orthogonal circularly polarized components. A binary Pancharatnam-Berry (P-B) phase gradient is obtained by rotating the unit 90 degrees, then the phase zone plate can be easily designed. The simulation results show that the proposed chiral metasurface zone plate has the function of reflection-transmission separation and focusing for the circularly polarized terahertz waves. In addition, we also demonstrate the possibility of using a 1064-nm continuous infrared laser to adjust the intensity of our devices, based on photo-generated carriers in silicon. The design principle of the chiral metasurface zone plates can be extended to other wavelengths, providing new ideas for the regulation of circularly polarized light.

High responsivity of VIS-NIR photodetector based on Ag2S/P3HT heterojunction.

Ag2S quantum dot (QD) photodetectors (PDs) have attracted a lot of attention in the field of imaging system and optical communication. However, the current Ag2S PDs mainly works in the near-infrared band, and its detection ability in the visible band remains to be strengthened. In this paper, we used poly(3-hexylthiophene) (P3HT) with high carrier mobility and Ag2S QDs to construct heterojunction PD. Stronger absorption in blends with polymer P3HT compared to single Ag2S QDs. The optical absorption spectra show that the Ag2S/P3HT has strong light absorption peak at 394 and 598 nm. The results show that P3HT significantly enhances the absorption of Ag2S QDs from the visible to near-infrared band. The output characteristics, transfer characteristics and fast switching capability of the device at 405 nm, 532 nm and 808 nm were tested. The device has the responsivity of 6.05 A W-1, 83.72 A W-1and 37.31 A W-1under 405 nm, 532 nm and 808 nm laser irradiation. This work plays an important role in improving the detection performance of Ag2S QDs and broadening its applications in photoelectric devices for weak light and wide spectrum detection.